Merge tag 'isci-for-3.5' into misc

isci update for 3.5

1/ Rework remote-node-context (RNC) handling for proper management of
   the silicon state machine in error handling and hot-plug conditions.
   Further details below, suffice to say if the RNC is mismanaged the
   silicon state machines may lock up.

2/ Refactor the initialization code to be reused for suspend/resume support

3/ Miscellaneous bug fixes to address discovery issues and hardware
   compatibility.

RNC rework details from Jeff Skirvin:

In the controller, devices as they appear on a SAS domain (or
direct-attached SATA devices) are represented by memory structures known
as "Remote Node Contexts" (RNCs).  These structures are transferred from
main memory to the controller using a set of register commands; these
commands include setting up the context ("posting"), removing the
context ("invalidating"), and commands to control the scheduling of
commands and connections to that remote device ("suspensions" and
"resumptions").  There is a similar path to control RNC scheduling from
the protocol engine, which interprets the results of command and data
transmission and reception.

In general, the controller chooses among non-suspended RNCs to find one
that has work requiring scheduling the transmission of command and data
frames to a target.  Likewise, when a target tries to return data back
to the initiator, the state of the RNC is used by the controller to
determine how to treat the incoming request. As an example, if the RNC
is in the state "TX/RX Suspended", incoming SSP connection requests from
the target will be rejected by the controller hardware.  When an RNC is
"TX Suspended", it will not be selected by the controller hardware to
start outgoing command or data operations (with certain priority-based
exceptions).

As mentioned above, there are two sources for management of the RNC
states: commands from driver software, and the result of transmission
and reception conditions of commands and data signaled by the controller
hardware.  As an example of the latter, if an outgoing SSP command ends
with a OPEN_REJECT(BAD_DESTINATION) status, the RNC state will
transition to the "TX Suspended" state, and this is signaled by the
controller hardware in the status to the completion of the pending
command as well as signaled in a controller hardware event.  Examples of
the former are included in the patch changelogs.

Driver software is required to suspend the RNC in a "TX/RX Suspended"
condition before any outstanding commands can be terminated.  Failure to
guarantee this can lead to a complete hardware hang condition.  Earlier
versions of the driver software did not guarantee that an RNC was
correctly managed before I/O termination, and so operated in an unsafe
way.

Further, the driver performed unnecessary contortions to preserve the
remote device command state and so was more complicated than it needed
to be.  A simplifying driver assumption is that once an I/O has entered
the error handler path without having completed in the target, the
requirement on the driver is that all use of the sas_task must end.
Beyond that, recovery of operation is dependent on libsas and other
components to reset, rediscover and reconfigure the device before normal
operation can restart.  In the driver, this simplifying assumption meant
that the RNC management could be reduced to entry into the suspended
state, terminating the targeted I/O request, and resuming the RNC as
needed for device-specific management such as an SSP Abort Task or LUN
Reset Management request.

1 files changed, 41 insertions, 5 deletions

diff --git a/arch/x86/xen/enlighten.c b/arch/x86/xen/enlighten.c
index 4f51bebac02c..95dccce8e979 100644
--- a/arch/x86/xen/enlighten.c
+++ b/arch/x86/xen/enlighten.c
@@ -63,6 +63,7 @@
 #include <asm/stackprotector.h>
 #include <asm/hypervisor.h>
 #include <asm/mwait.h>
+#include <asm/pci_x86.h>
 
 #ifdef CONFIG_ACPI
 #include <linux/acpi.h>
@@ -261,7 +262,8 @@ static void xen_cpuid(unsigned int *ax, unsigned int *bx,
 
 static bool __init xen_check_mwait(void)
 {
-#ifdef CONFIG_ACPI
+#if defined(CONFIG_ACPI) && !defined(CONFIG_ACPI_PROCESSOR_AGGREGATOR) && \
+	!defined(CONFIG_ACPI_PROCESSOR_AGGREGATOR_MODULE)
 	struct xen_platform_op op = {
 		.cmd			= XENPF_set_processor_pminfo,
 		.u.set_pminfo.id	= -1,
@@ -349,7 +351,6 @@ static void __init xen_init_cpuid_mask(void)
 	/* Xen will set CR4.OSXSAVE if supported and not disabled by force */
 	if ((cx & xsave_mask) != xsave_mask)
 		cpuid_leaf1_ecx_mask &= ~xsave_mask; /* disable XSAVE & OSXSAVE */
-
 	if (xen_check_mwait())
 		cpuid_leaf1_ecx_set_mask = (1 << (X86_FEATURE_MWAIT % 32));
 }
@@ -809,9 +810,40 @@ static void xen_io_delay(void)
 }
 
 #ifdef CONFIG_X86_LOCAL_APIC
+static unsigned long xen_set_apic_id(unsigned int x)
+{
+	WARN_ON(1);
+	return x;
+}
+static unsigned int xen_get_apic_id(unsigned long x)
+{
+	return ((x)>>24) & 0xFFu;
+}
 static u32 xen_apic_read(u32 reg)
 {
-	return 0;
+	struct xen_platform_op op = {
+		.cmd = XENPF_get_cpuinfo,
+		.interface_version = XENPF_INTERFACE_VERSION,
+		.u.pcpu_info.xen_cpuid = 0,
+	};
+	int ret = 0;
+
+	/* Shouldn't need this as APIC is turned off for PV, and we only
+	 * get called on the bootup processor. But just in case. */
+	if (!xen_initial_domain() || smp_processor_id())
+		return 0;
+
+	if (reg == APIC_LVR)
+		return 0x10;
+
+	if (reg != APIC_ID)
+		return 0;
+
+	ret = HYPERVISOR_dom0_op(&op);
+	if (ret)
+		return 0;
+
+	return op.u.pcpu_info.apic_id << 24;
 }
 
 static void xen_apic_write(u32 reg, u32 val)
@@ -849,6 +881,8 @@ static void set_xen_basic_apic_ops(void)
 	apic->icr_write = xen_apic_icr_write;
 	apic->wait_icr_idle = xen_apic_wait_icr_idle;
 	apic->safe_wait_icr_idle = xen_safe_apic_wait_icr_idle;
+	apic->set_apic_id = xen_set_apic_id;
+	apic->get_apic_id = xen_get_apic_id;
 }
 
 #endif
@@ -1365,8 +1399,10 @@ asmlinkage void __init xen_start_kernel(void)
 		/* Make sure ACS will be enabled */
 		pci_request_acs();
 	}
-		
-
+#ifdef CONFIG_PCI
+	/* PCI BIOS service won't work from a PV guest. */
+	pci_probe &= ~PCI_PROBE_BIOS;
+#endif
 	xen_raw_console_write("about to get started...\n");
 
 	xen_setup_runstate_info(0);