powerpc: Remove arch/ppc and include/asm-ppc

All the maintained platforms are now in arch/powerpc, so the old
arch/ppc stuff can now go away.

Acked-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Becky Bruce <becky.bruce@freescale.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Jochen Friedrich <jochen@scram.de>
Acked-by: John Linn <john.linn@xilinx.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Scott Wood <scottwood@freescale.com>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>

1 files changed, 0 insertions, 75 deletions

diff --git a/arch/ppc/platforms/sandpoint.h b/arch/ppc/platforms/sandpoint.h
deleted file mode 100644
index ed83759e4044..000000000000
--- a/arch/ppc/platforms/sandpoint.h
+++ /dev/null
@@ -1,75 +0,0 @@
-/*
- * Definitions for Motorola SPS Sandpoint Test Platform
- *
- * Author: Mark A. Greer
- *         mgreer@mvista.com
- *
- * 2000-2003 (c) MontaVista, Software, Inc.  This file is licensed under
- * the terms of the GNU General Public License version 2.  This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
- */
-
-/*
- * Sandpoint uses the CHRP map (Map B).
- */
-
-#ifndef __PPC_PLATFORMS_SANDPOINT_H
-#define __PPC_PLATFORMS_SANDPOINT_H
-
-#include <asm/ppcboot.h>
-
-#if 0
-/* The Sandpoint X3 allows the IDE interrupt to be directly connected
- * from the Windbond (PCI INTC or INTD) to the serial EPIC.  Someday
- * we should try this, but it was easier to use the existing 83c553
- * initialization than change it to route the different interrupts :-).
- *	-- Dan
- */
-#define SANDPOINT_IDE_INT0		23	/* EPIC 7 */
-#define SANDPOINT_IDE_INT1		24	/* EPIC 8 */
-#endif
-
-/*
- * The sandpoint boards have processor modules that either have an 8240 or
- * an MPC107 host bridge on them.  These bridges have an IDSEL line that allows
- * them to respond to PCI transactions as if they were a normal PCI devices.
- * However, the processor on the processor side of the bridge can not reach
- * out onto the PCI bus and then select the bridge or bad things will happen
- * (documented in the 8240 and 107 manuals).
- * Because of this, we always skip the bridge PCI device when accessing the
- * PCI bus.  The PCI slot that the bridge occupies is defined by the macro
- * below.
- */
-#define SANDPOINT_HOST_BRIDGE_IDSEL     12
-
-/*
- * Serial defines.
- */
-#define SANDPOINT_SERIAL_0		0xfe0003f8
-#define SANDPOINT_SERIAL_1		0xfe0002f8
-
-#define RS_TABLE_SIZE  2
-
-/* Rate for the 1.8432 Mhz clock for the onboard serial chip */
-#define BASE_BAUD			( 1843200 / 16 )
-#define UART_CLK			1843200
-
-#ifdef CONFIG_SERIAL_DETECT_IRQ
-#define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF|ASYNC_AUTO_IRQ)
-#else
-#define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF)
-#endif
-
-#define STD_SERIAL_PORT_DFNS \
-        { 0, BASE_BAUD, SANDPOINT_SERIAL_0, 4, STD_COM_FLAGS, /* ttyS0 */ \
-		iomem_base: (u8 *)SANDPOINT_SERIAL_0,			  \
-		io_type: SERIAL_IO_MEM },				  \
-        { 0, BASE_BAUD, SANDPOINT_SERIAL_1, 3, STD_COM_FLAGS, /* ttyS1 */ \
-		iomem_base: (u8 *)SANDPOINT_SERIAL_1,			  \
-		io_type: SERIAL_IO_MEM },
-
-#define SERIAL_PORT_DFNS \
-        STD_SERIAL_PORT_DFNS
-
-#endif /* __PPC_PLATFORMS_SANDPOINT_H */