diff options
| author | Arnd Bergmann <arnd@arndb.de> | 2019-09-03 16:10:52 +0200 |
|---|---|---|
| committer | Arnd Bergmann <arnd@arndb.de> | 2019-09-03 16:10:53 +0200 |
| commit | e8e39a2026abc7f148e3b92bf0d5c9721c2c6bff (patch) | |
| tree | 04df1d9dd2918ff85bf19adc76d4c8db6fb975cc /arch/arm64/boot | |
| parent | a0a4c25fba92d570f3256495328787ee30c3b044 (diff) | |
| parent | 215701807e53a379e1c9b2e6401676779ef85ea0 (diff) | |
| download | linux-e8e39a2026abc7f148e3b92bf0d5c9721c2c6bff.tar.bz2 | |
Merge tag 'imx-dt64-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX arm64 device tree update for 5.4:
- New board support: i.MX8MQ Nitrogen8m, Hummingboard Pulse,
PICO-PI-IMX8M, i.MX8QXP AI_ML, and LS1046A FRWY board.
- Add gpio-ranges for GPIO devices on i.MX8MQ and i.MX8MM.
- Update OPP table according to latest data sheet and add opp-suspend
to OPP table for i.MX8MQ and i.MX8MM.
- Add IDEL states for i.MX8MM SoC.
- Correct I2C clock divider for Layerscape SoCs.
- Add series alias and LPUART baud clock for i.MX8QXP SoC.
- Add MIPI D-PHY device for i.MX8MQ and enable it on imx8mq-librem5
board.
- Enable USB1 and Type-C support for i.MX8MM EVK board.
- Add Thermal Monitor Unit support for LS1028A SoC.
- Misc small update and correction on Layerscape and i.MX8 support.
* tag 'imx-dt64-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (41 commits)
arm64: dts: imx8mq: Add mux controller to iomuxc_gpr
arm64: dts: fsl: add support for Hummingboard Pulse
arm64: dts: ls1088a: update gpio compatible
arm64: dts: imx: Add i.mx8mq nitrogen8m basic dts support
arm64: dts: ls1088a-qds: Add the spi-flash nodes under the DSPI controller
arm64: dts: ls1088a: Add the DSPI controller node
arm64: dts: imx8mm: Enable cpu-idle driver
arm64: dts: ls1028a: Add esdhc node in dts
arm64: dts: ls1028a: Add properties node for Display output pixel clock
arm64: dts: lx2160a: Fix incorrect I2C clock divider
arm64: dts: ls1028a: Fix incorrect I2C clock divider
arm64: dts: ls1012a: Fix incorrect I2C clock divider
arm64: dts: ls1088a: Fix incorrect I2C clock divider
arm64: dts: ls1028a: fix gpio nodes
arm64: dts: ls1028a: Add Thermal Monitor Unit node
arm64: dts: imx8mq-evk: Unbypass audio_pll1
arm64: dts: imx8mm: Add opp-suspend property to OPP table
arm64: dts: imx8mq: Add opp-suspend property to OPP table
arm64: dts: ls1088a: Revise gpio registers to little-endian
arm64: dts: add the console node for DPAA2 platforms
...
Link: https://lore.kernel.org/r/20190825153237.28829-6-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Diffstat (limited to 'arch/arm64/boot')
22 files changed, 2241 insertions, 84 deletions
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile index 9ca375640f23..93fce8f0c66d 100644 --- a/arch/arm64/boot/dts/freescale/Makefile +++ b/arch/arm64/boot/dts/freescale/Makefile @@ -8,6 +8,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-rdb.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-qds.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-rdb.dtb +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1046a-frwy.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1046a-qds.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1046a-rdb.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1088a-qds.dtb @@ -23,7 +24,11 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mq-evk.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mq-hummingboard-pulse.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mq-nitrogen.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mq-pico-pi.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-rmb3.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-zest.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8qxp-ai_ml.dtb dtb-$(CONFIG_ARCH_MXC) += imx8qxp-mek.dtb diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi index ec6257a5b251..124a7e2d8442 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi @@ -323,7 +323,7 @@ #size-cells = <0>; reg = <0x0 0x2180000 0x0 0x10000>; interrupts = <0 56 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 0>; + clocks = <&clockgen 4 3>; status = "disabled"; }; @@ -333,7 +333,7 @@ #size-cells = <0>; reg = <0x0 0x2190000 0x0 0x10000>; interrupts = <0 57 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 0>; + clocks = <&clockgen 4 3>; status = "disabled"; }; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts index de6ef39f3118..5e14e5a19744 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts @@ -95,6 +95,14 @@ status = "okay"; }; +&esdhc { + status = "okay"; +}; + +&esdhc1 { + status = "okay"; +}; + &i2c0 { status = "okay"; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts index 9fb911317ecd..1a69221d9a1b 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts @@ -83,6 +83,19 @@ }; }; +&esdhc { + sd-uhs-sdr104; + sd-uhs-sdr50; + sd-uhs-sdr25; + sd-uhs-sdr12; + status = "okay"; +}; + +&esdhc1 { + mmc-hs200-1_8v; + status = "okay"; +}; + &i2c0 { status = "okay"; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi index 7975519b4f56..b139b29cef87 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi @@ -29,6 +29,7 @@ clocks = <&clockgen 1 0>; next-level-cache = <&l2>; cpu-idle-states = <&CPU_PW20>; + #cooling-cells = <2>; }; cpu1: cpu@1 { @@ -39,6 +40,7 @@ clocks = <&clockgen 1 0>; next-level-cache = <&l2>; cpu-idle-states = <&CPU_PW20>; + #cooling-cells = <2>; }; l2: l2-cache { @@ -70,11 +72,18 @@ clock-output-names = "sysclk"; }; - dpclk: clock-dp { + osc_27m: clock-osc-27m { compatible = "fixed-clock"; #clock-cells = <0>; clock-frequency = <27000000>; - clock-output-names= "dpclk"; + clock-output-names = "phy_27m"; + }; + + dpclk: clock-controller@f1f0000 { + compatible = "fsl,ls1028a-plldig"; + reg = <0x0 0xf1f0000 0x0 0xffff>; + #clock-cells = <1>; + clocks = <&osc_27m>; }; aclk: clock-axi { @@ -171,7 +180,7 @@ #size-cells = <0>; reg = <0x0 0x2000000 0x0 0x10000>; interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 1>; + clocks = <&clockgen 4 3>; status = "disabled"; }; @@ -181,7 +190,7 @@ #size-cells = <0>; reg = <0x0 0x2010000 0x0 0x10000>; interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 1>; + clocks = <&clockgen 4 3>; status = "disabled"; }; @@ -191,7 +200,7 @@ #size-cells = <0>; reg = <0x0 0x2020000 0x0 0x10000>; interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 1>; + clocks = <&clockgen 4 3>; status = "disabled"; }; @@ -201,7 +210,7 @@ #size-cells = <0>; reg = <0x0 0x2030000 0x0 0x10000>; interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 1>; + clocks = <&clockgen 4 3>; status = "disabled"; }; @@ -211,7 +220,7 @@ #size-cells = <0>; reg = <0x0 0x2040000 0x0 0x10000>; interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 1>; + clocks = <&clockgen 4 3>; status = "disabled"; }; @@ -221,7 +230,7 @@ #size-cells = <0>; reg = <0x0 0x2050000 0x0 0x10000>; interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 1>; + clocks = <&clockgen 4 3>; status = "disabled"; }; @@ -231,7 +240,7 @@ #size-cells = <0>; reg = <0x0 0x2060000 0x0 0x10000>; interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 1>; + clocks = <&clockgen 4 3>; status = "disabled"; }; @@ -241,7 +250,34 @@ #size-cells = <0>; reg = <0x0 0x2070000 0x0 0x10000>; interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 1>; + clocks = <&clockgen 4 3>; + status = "disabled"; + }; + + esdhc: mmc@2140000 { + compatible = "fsl,ls1028a-esdhc", "fsl,esdhc"; + reg = <0x0 0x2140000 0x0 0x10000>; + interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; + clock-frequency = <0>; /* fixed up by bootloader */ + clocks = <&clockgen 2 1>; + voltage-ranges = <1800 1800 3300 3300>; + sdhci,auto-cmd12; + little-endian; + bus-width = <4>; + status = "disabled"; + }; + + esdhc1: mmc@2150000 { + compatible = "fsl,ls1028a-esdhc", "fsl,esdhc"; + reg = <0x0 0x2150000 0x0 0x10000>; + interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>; + clock-frequency = <0>; /* fixed up by bootloader */ + clocks = <&clockgen 2 1>; + voltage-ranges = <1800 1800 3300 3300>; + sdhci,auto-cmd12; + broken-cd; + little-endian; + bus-width = <4>; status = "disabled"; }; @@ -277,33 +313,36 @@ }; gpio1: gpio@2300000 { - compatible = "fsl,qoriq-gpio"; + compatible = "fsl,ls1028a-gpio","fsl,qoriq-gpio"; reg = <0x0 0x2300000 0x0 0x10000>; interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; + little-endian; }; gpio2: gpio@2310000 { - compatible = "fsl,qoriq-gpio"; + compatible = "fsl,ls1028a-gpio","fsl,qoriq-gpio"; reg = <0x0 0x2310000 0x0 0x10000>; interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; + little-endian; }; gpio3: gpio@2320000 { - compatible = "fsl,qoriq-gpio"; + compatible = "fsl,ls1028a-gpio","fsl,qoriq-gpio"; reg = <0x0 0x2320000 0x0 0x10000>; interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; + little-endian; }; usb0: usb@3100000 { @@ -503,6 +542,89 @@ status = "disabled"; }; + tmu: tmu@1f00000 { + compatible = "fsl,qoriq-tmu"; + reg = <0x0 0x1f80000 0x0 0x10000>; + interrupts = <0 23 0x4>; + fsl,tmu-range = <0xb0000 0xa0026 0x80048 0x70061>; + fsl,tmu-calibration = <0x00000000 0x00000024 + 0x00000001 0x0000002b + 0x00000002 0x00000031 + 0x00000003 0x00000038 + 0x00000004 0x0000003f + 0x00000005 0x00000045 + 0x00000006 0x0000004c + 0x00000007 0x00000053 + 0x00000008 0x00000059 + 0x00000009 0x00000060 + 0x0000000a 0x00000066 + 0x0000000b 0x0000006d + + 0x00010000 0x0000001c + 0x00010001 0x00000024 + 0x00010002 0x0000002c + 0x00010003 0x00000035 + 0x00010004 0x0000003d + 0x00010005 0x00000045 + 0x00010006 0x0000004d + 0x00010007 0x00000045 + 0x00010008 0x0000005e + 0x00010009 0x00000066 + 0x0001000a 0x0000006e + + 0x00020000 0x00000018 + 0x00020001 0x00000022 + 0x00020002 0x0000002d + 0x00020003 0x00000038 + 0x00020004 0x00000043 + 0x00020005 0x0000004d + 0x00020006 0x00000058 + 0x00020007 0x00000063 + 0x00020008 0x0000006e + + 0x00030000 0x00000010 + 0x00030001 0x0000001c + 0x00030002 0x00000029 + 0x00030003 0x00000036 + 0x00030004 0x00000042 + 0x00030005 0x0000004f + 0x00030006 0x0000005b + 0x00030007 0x00000068>; + little-endian; + #thermal-sensor-cells = <1>; + }; + + thermal-zones { + core-cluster { + polling-delay-passive = <1000>; + polling-delay = <5000>; + thermal-sensors = <&tmu 0>; + + trips { + core_cluster_alert: core-cluster-alert { + temperature = <85000>; + hysteresis = <2000>; + type = "passive"; + }; + + core_cluster_crit: core-cluster-crit { + temperature = <95000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&core_cluster_alert>; + cooling-device = + <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + }; + pcie@1f0000000 { /* Integrated Endpoint Root Complex */ compatible = "pci-host-ecam-generic"; reg = <0x01 0xf0000000 0x0 0x100000>; @@ -551,9 +673,10 @@ interrupts = <0 222 IRQ_TYPE_LEVEL_HIGH>, <0 223 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "DE", "SE"; - clocks = <&dpclk>, <&aclk>, <&aclk>, <&pclk>; + clocks = <&dpclk 0>, <&aclk>, <&aclk>, <&pclk>; clock-names = "pxlclk", "mclk", "aclk", "pclk"; arm,malidp-output-port-lines = /bits/ 8 <8 8 8>; + arm,malidp-arqos-value = <0xd000d000>; port { dp0_out: endpoint { diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1046a-frwy.dts b/arch/arm64/boot/dts/freescale/fsl-ls1046a-frwy.dts new file mode 100644 index 000000000000..3595be0f2527 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/fsl-ls1046a-frwy.dts @@ -0,0 +1,155 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Device Tree Include file for Freescale Layerscape-1046A family SoC. + * + * Copyright 2019 NXP. + * + */ + +/dts-v1/; + +#include "fsl-ls1046a.dtsi" + +/ { + model = "LS1046A FRWY Board"; + compatible = "fsl,ls1046a-frwy", "fsl,ls1046a"; + + aliases { + serial0 = &duart0; + serial1 = &duart1; + serial2 = &duart2; + serial3 = &duart3; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + sb_3v3: regulator-sb3v3 { + compatible = "regulator-fixed"; + regulator-name = "LT8642SEV-3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; +}; + +&duart0 { + status = "okay"; +}; + +&duart1 { + status = "okay"; +}; + +&duart2 { + status = "okay"; +}; + +&duart3 { + status = "okay"; +}; + +&i2c0 { + status = "okay"; + + i2c-mux@77 { + compatible = "nxp,pca9546"; + reg = <0x77>; + #address-cells = <1>; + #size-cells = <0>; + + i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + power-monitor@40 { + compatible = "ti,ina220"; + reg = <0x40>; + shunt-resistor = <1000>; + }; + + temperature-sensor@4c { + compatible = "nxp,sa56004"; + reg = <0x4c>; + vcc-supply = <&sb_3v3>; + }; + + rtc@51 { + compatible = "nxp,pcf2129"; + reg = <0x51>; + }; + + eeprom@52 { + compatible = "atmel,24c512"; + reg = <0x52>; + }; + + eeprom@53 { + compatible = "atmel,24c512"; + reg = <0x53>; + }; + + }; + }; +}; + +&ifc { + #address-cells = <2>; + #size-cells = <1>; + /* NAND Flash */ + ranges = <0x0 0x0 0x0 0x7e800000 0x00010000>; + status = "okay"; + + nand@0,0 { + compatible = "fsl,ifc-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x0 0x0 0x10000>; + }; + +}; + +#include "fsl-ls1046-post.dtsi" + +&fman0 { + ethernet@e0000 { + phy-handle = <&qsgmii_phy4>; + phy-connection-type = "qsgmii"; + }; + + ethernet@e8000 { + phy-handle = <&qsgmii_phy2>; + phy-connection-type = "qsgmii"; + }; + + ethernet@ea000 { + phy-handle = <&qsgmii_phy1>; + phy-connection-type = "qsgmii"; + }; + + ethernet@f2000 { + phy-handle = <&qsgmii_phy3>; + phy-connection-type = "qsgmii"; + }; + + mdio@fd000 { + qsgmii_phy1: ethernet-phy@1c { + reg = <0x1c>; + }; + + qsgmii_phy2: ethernet-phy@1d { + reg = <0x1d>; + }; + + qsgmii_phy3: ethernet-phy@1e { + reg = <0x1e>; + }; + + qsgmii_phy4: ethernet-phy@1f { + reg = <0x1f>; + }; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1088a-qds.dts index 6f48d21b97c0..120e62dad154 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1088a-qds.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a-qds.dts @@ -17,6 +17,39 @@ compatible = "fsl,ls1088a-qds", "fsl,ls1088a"; }; +&dspi { + bus-num = <0>; + status = "okay"; + + flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <1000000>; + }; + + flash@1 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + spi-cpol; + spi-cpha; + spi-max-frequency = <3500000>; + reg = <1>; + }; + + flash@2 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + spi-cpol; + spi-cpha; + spi-max-frequency = <3500000>; + reg = <2>; + }; +}; + &i2c0 { status = "okay"; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi index dacd8cf03a7f..d1469b0747c7 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi @@ -252,6 +252,19 @@ #thermal-sensor-cells = <1>; }; + dspi: spi@2100000 { + compatible = "fsl,ls1088a-dspi", + "fsl,ls1021a-v1.0-dspi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x2100000 0x0 0x10000>; + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "dspi"; + clocks = <&clockgen 4 1>; + spi-num-chipselects = <6>; + status = "disabled"; + }; + duart0: serial@21c0500 { compatible = "fsl,ns16550", "ns16550a"; reg = <0x0 0x21c0500 0x0 0x100>; @@ -269,9 +282,10 @@ }; gpio0: gpio@2300000 { - compatible = "fsl,qoriq-gpio"; + compatible = "fsl,ls1088a-gpio", "fsl,qoriq-gpio"; reg = <0x0 0x2300000 0x0 0x10000>; interrupts = <0 36 IRQ_TYPE_LEVEL_HIGH>; + little-endian; gpio-controller; #gpio-cells = <2>; interrupt-controller; @@ -279,9 +293,10 @@ }; gpio1: gpio@2310000 { - compatible = "fsl,qoriq-gpio"; + compatible = "fsl,ls1088a-gpio", "fsl,qoriq-gpio"; reg = <0x0 0x2310000 0x0 0x10000>; interrupts = <0 36 IRQ_TYPE_LEVEL_HIGH>; + little-endian; gpio-controller; #gpio-cells = <2>; interrupt-controller; @@ -289,9 +304,10 @@ }; gpio2: gpio@2320000 { - compatible = "fsl,qoriq-gpio"; + compatible = "fsl,ls1088a-gpio", "fsl,qoriq-gpio"; reg = <0x0 0x2320000 0x0 0x10000>; interrupts = <0 37 IRQ_TYPE_LEVEL_HIGH>; + little-endian; gpio-controller; #gpio-cells = <2>; interrupt-controller; @@ -299,9 +315,10 @@ }; gpio3: gpio@2330000 { - compatible = "fsl,qoriq-gpio"; + compatible = "fsl,ls1088a-gpio", "fsl,qoriq-gpio"; reg = <0x0 0x2330000 0x0 0x10000>; interrupts = <0 37 IRQ_TYPE_LEVEL_HIGH>; + little-endian; gpio-controller; #gpio-cells = <2>; interrupt-controller; @@ -324,7 +341,7 @@ #size-cells = <0>; reg = <0x0 0x2000000 0x0 0x10000>; interrupts = <0 34 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 3>; + clocks = <&clockgen 4 7>; status = "disabled"; }; @@ -334,7 +351,7 @@ #size-cells = <0>; reg = <0x0 0x2010000 0x0 0x10000>; interrupts = <0 34 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 3>; + clocks = <&clockgen 4 7>; status = "disabled"; }; @@ -344,7 +361,7 @@ #size-cells = <0>; reg = <0x0 0x2020000 0x0 0x10000>; interrupts = <0 35 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 3>; + clocks = <&clockgen 4 7>; status = "disabled"; }; @@ -354,7 +371,7 @@ #size-cells = <0>; reg = <0x0 0x2030000 0x0 0x10000>; interrupts = <0 35 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 3>; + clocks = <&clockgen 4 7>; status = "disabled"; }; @@ -609,6 +626,11 @@ <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>; }; + console@8340020 { + compatible = "fsl,dpaa2-console"; + reg = <0x00000000 0x08340020 0 0x2>; + }; + ptp-timer@8b95000 { compatible = "fsl,dpaa2-ptp"; reg = <0x0 0x8b95000 0x0 0x100>; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi index 3ace91945b72..64101c9962ce 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi @@ -321,6 +321,11 @@ }; }; + console@8340020 { + compatible = "fsl,dpaa2-console"; + reg = <0x00000000 0x08340020 0 0x2>; + }; + ptp-timer@8b95000 { compatible = "fsl,dpaa2-ptp"; reg = <0x0 0x8b95000 0x0 0x100>; diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi b/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi index e6fdba39453c..408e0ecdce6a 100644 --- a/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi @@ -485,7 +485,7 @@ reg = <0x0 0x2000000 0x0 0x10000>; interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; clock-names = "i2c"; - clocks = <&clockgen 4 7>; + clocks = <&clockgen 4 15>; scl-gpio = <&gpio2 15 GPIO_ACTIVE_HIGH>; status = "disabled"; }; @@ -497,7 +497,7 @@ reg = <0x0 0x2010000 0x0 0x10000>; interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; clock-names = "i2c"; - clocks = <&clockgen 4 7>; + clocks = <&clockgen 4 15>; status = "disabled"; }; @@ -508,7 +508,7 @@ reg = <0x0 0x2020000 0x0 0x10000>; interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; clock-names = "i2c"; - clocks = <&clockgen 4 7>; + clocks = <&clockgen 4 15>; status = "disabled"; }; @@ -519,7 +519,7 @@ reg = <0x0 0x2030000 0x0 0x10000>; interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; clock-names = "i2c"; - clocks = <&clockgen 4 7>; + clocks = <&clockgen 4 15>; status = "disabled"; }; @@ -530,7 +530,7 @@ reg = <0x0 0x2040000 0x0 0x10000>; interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; clock-names = "i2c"; - clocks = <&clockgen 4 7>; + clocks = <&clockgen 4 15>; scl-gpio = <&gpio2 16 GPIO_ACTIVE_HIGH>; status = "disabled"; }; @@ -542,7 +542,7 @@ reg = <0x0 0x2050000 0x0 0x10000>; interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; clock-names = "i2c"; - clocks = <&clockgen 4 7>; + clocks = <&clockgen 4 15>; status = "disabled"; }; @@ -553,7 +553,7 @@ reg = <0x0 0x2060000 0x0 0x10000>; interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; clock-names = "i2c"; - clocks = <&clockgen 4 7>; + clocks = <&clockgen 4 15>; status = "disabled"; }; @@ -564,7 +564,7 @@ reg = <0x0 0x2070000 0x0 0x10000>; interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; clock-names = "i2c"; - clocks = <&clockgen 4 7>; + clocks = <&clockgen 4 15>; status = "disabled"; }; @@ -848,6 +848,11 @@ dma-coherent; }; + console@8340020 { + compatible = "fsl,dpaa2-console"; + reg = <0x00000000 0x08340020 0 0x2>; + }; + ptp-timer@8b95000 { compatible = "fsl,dpaa2-ptp"; reg = <0x0 0x8b95000 0x0 0x100>; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-evk.dts b/arch/arm64/boot/dts/freescale/imx8mm-evk.dts index ee7f2b2fc1ff..f7a15f3904c2 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-evk.dts +++ b/arch/arm64/boot/dts/freescale/imx8mm-evk.dts @@ -5,6 +5,7 @@ /dts-v1/; +#include <dt-bindings/usb/pd.h> #include "imx8mm.dtsi" / { @@ -89,9 +90,6 @@ ethphy0: ethernet-phy@0 { compatible = "ethernet-phy-ieee802.3-c22"; reg = <0>; - at803x,led-act-blind-workaround; - at803x,eee-okay; - at803x,vddio-1p8v; }; }; }; @@ -115,6 +113,21 @@ status = "okay"; }; +&usbotg1 { + dr_mode = "otg"; + hnp-disable; + srp-disable; + adp-disable; + usb-role-switch; + status = "okay"; + + port { + usb1_drd_sw: endpoint { + remote-endpoint = <&typec1_dr_sw>; + }; + }; +}; + &usdhc2 { pinctrl-names = "default", "state_100mhz", "state_200mhz"; pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; @@ -257,6 +270,42 @@ }; }; +&i2c2 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + ptn5110: tcpc@50 { + compatible = "nxp,ptn5110"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_typec1>; + reg = <0x50>; + interrupt-parent = <&gpio2>; + interrupts = <11 8>; + status = "okay"; + + port { + typec1_dr_sw: endpoint { + remote-endpoint = <&usb1_drd_sw>; + }; + }; + + typec1_con: connector { + compatible = "usb-c-connector"; + label = "USB-C"; + power-role = "dual"; + data-role = "dual"; + try-power-role = "sink"; + source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>; + sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM) + PDO_VAR(5000, 20000, 3000)>; + op-sink-microwatt = <15000000>; + self-powered; + }; + }; +}; + &iomuxc { pinctrl-names = "default"; @@ -299,6 +348,13 @@ >; }; + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL 0x400001c3 + MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA 0x400001c3 + >; + }; + pinctrl_pmic: pmicirq { fsl,pins = < MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x41 @@ -320,6 +376,12 @@ >; }; + pinctrl_typec1: typec1grp { + fsl,pins = < + MX8MM_IOMUXC_SD1_STROBE_GPIO2_IO11 0x159 + >; + }; + pinctrl_uart2: uart2grp { fsl,pins = < MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX 0x140 diff --git a/arch/arm64/boot/dts/freescale/imx8mm.dtsi b/arch/arm64/boot/dts/freescale/imx8mm.dtsi index 232a7412755a..984ea7b3fd9f 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mm.dtsi @@ -44,6 +44,19 @@ #address-cells = <1>; #size-cells = <0>; + idle-states { + entry-method = "psci"; + + cpu_pd_wait: cpu-pd-wait { + compatible = "arm,idle-state"; + arm,psci-suspend-param = <0x0010033>; + local-timer-stop; + entry-latency-us = <1000>; + exit-latency-us = <700>; + min-residency-us = <2700>; + }; + }; + A53_0: cpu@0 { device_type = "cpu"; compatible = "arm,cortex-a53"; @@ -55,6 +68,7 @@ operating-points-v2 = <&a53_opp_table>; nvmem-cells = <&cpu_speed_grade>; nvmem-cell-names = "speed_grade"; + cpu-idle-states = <&cpu_pd_wait>; }; A53_1: cpu@1 { @@ -66,6 +80,7 @@ enable-method = "psci"; next-level-cache = <&A53_L2>; operating-points-v2 = <&a53_opp_table>; + cpu-idle-states = <&cpu_pd_wait>; }; A53_2: cpu@2 { @@ -77,6 +92,7 @@ enable-method = "psci"; next-level-cache = <&A53_L2>; operating-points-v2 = <&a53_opp_table>; + cpu-idle-states = <&cpu_pd_wait>; }; A53_3: cpu@3 { @@ -88,6 +104,7 @@ enable-method = "psci"; next-level-cache = <&A53_L2>; operating-points-v2 = <&a53_opp_table>; + cpu-idle-states = <&cpu_pd_wait>; }; A53_L2: l2-cache0 { @@ -104,6 +121,7 @@ opp-microvolt = <850000>; opp-supported-hw = <0xe>, <0x7>; clock-latency-ns = <150000>; + opp-suspend; }; opp-1600000000 { @@ -111,14 +129,15 @@ opp-microvolt = <900000>; opp-supported-hw = <0xc>, <0x7>; clock-latency-ns = <150000>; + opp-suspend; }; opp-1800000000 { opp-hz = /bits/ 64 <1800000000>; opp-microvolt = <1000000>; - /* Consumer only but rely on speed grading */ - opp-supported-hw = <0x8>, <0x7>; + opp-supported-hw = <0x8>, <0x3>; clock-latency-ns = <150000>; + opp-suspend; }; }; @@ -295,6 +314,7 @@ #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; + gpio-ranges = <&iomuxc 0 10 30>; }; gpio2: gpio@30210000 { @@ -307,6 +327,7 @@ #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; + gpio-ranges = <&iomuxc 0 40 21>; }; gpio3: gpio@30220000 { @@ -319,6 +340,7 @@ #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; + gpio-ranges = <&iomuxc 0 61 26>; }; gpio4: gpio@30230000 { @@ -331,6 +353,7 @@ #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; + gpio-ranges = <&iomuxc 0 87 32>; }; gpio5: gpio@30240000 { @@ -343,6 +366,7 @@ #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; + gpio-ranges = <&iomuxc 0 119 30>; }; wdog1: watchdog@30280000 { @@ -451,10 +475,22 @@ <&clk_ext3>, <&clk_ext4>; clock-names = "osc_32k", "osc_24m", "clk_ext1", "clk_ext2", "clk_ext3", "clk_ext4"; + assigned-clocks = <&clk IMX8MM_CLK_NOC>, + <&clk IMX8MM_CLK_AUDIO_AHB>, + <&clk IMX8MM_CLK_IPG_AUDIO_ROOT>, + <&clk IMX8MM_SYS_PLL3>, + <&clk IMX8MM_VIDEO_PLL1>; + assigned-clock-parents = <&clk IMX8MM_SYS_PLL3_OUT>, + <&clk IMX8MM_SYS_PLL1_800M>; + assigned-clock-rates = <0>, + <400000000>, + <400000000>, + <750000000>, + <594000000>; }; src: reset-controller@30390000 { - compatible = "fsl,imx8mm-src", "syscon"; + compatible = "fsl,imx8mm-src", "fsl,imx8mq-src", "syscon"; reg = <0x30390000 0x10000>; interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; #reset-cells = <1>; @@ -743,10 +779,8 @@ interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clk IMX8MM_CLK_USB1_CTRL_ROOT>; clock-names = "usb1_ctrl_root_clk"; - assigned-clocks = <&clk IMX8MM_CLK_USB_BUS>, - <&clk IMX8MM_CLK_USB_CORE_REF>; - assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_500M>, - <&clk IMX8MM_SYS_PLL1_100M>; + assigned-clocks = <&clk IMX8MM_CLK_USB_BUS>; + assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_500M>; fsl,usbphy = <&usbphynop1>; fsl,usbmisc = <&usbmisc1 0>; status = "disabled"; @@ -764,10 +798,8 @@ interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clk IMX8MM_CLK_USB1_CTRL_ROOT>; clock-names = "usb1_ctrl_root_clk"; - assigned-clocks = <&clk IMX8MM_CLK_USB_BUS>, - <&clk IMX8MM_CLK_USB_CORE_REF>; - assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_500M>, - <&clk IMX8MM_SYS_PLL1_100M>; + assigned-clocks = <&clk IMX8MM_CLK_USB_BUS>; + assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_500M>; fsl,usbphy = <&usbphynop2>; fsl,usbmisc = <&usbmisc2 0>; status = "disabled"; @@ -818,5 +850,12 @@ interrupt-controller; interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; }; + + ddr-pmu@3d800000 { + compatible = "fsl,imx8mm-ddr-pmu", "fsl,imx8m-ddr-pmu"; + reg = <0x3d800000 0x400000>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + }; }; }; diff --git a/arch/arm64/boot/dts/freescale/imx8mq-evk.dts b/arch/arm64/boot/dts/freescale/imx8mq-evk.dts index e3df9b8cd9ca..05958124f173 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq-evk.dts +++ b/arch/arm64/boot/dts/freescale/imx8mq-evk.dts @@ -118,9 +118,9 @@ &sai2 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_sai2>; - assigned-clocks = <&clk IMX8MQ_CLK_SAI2>; - assigned-clock-parents = <&clk IMX8MQ_AUDIO_PLL1_OUT>; - assigned-clock-rates = <24576000>; + assigned-clocks = <&clk IMX8MQ_AUDIO_PLL1_BYPASS>, <&clk IMX8MQ_CLK_SAI2>; + assigned-clock-parents = <&clk IMX8MQ_AUDIO_PLL1>, <&clk IMX8MQ_AUDIO_PLL1_OUT>; + assigned-clock-rates = <0>, <24576000>; status = "okay"; }; diff --git a/arch/arm64/boot/dts/freescale/imx8mq-hummingboard-pulse.dts b/arch/arm64/boot/dts/freescale/imx8mq-hummingboard-pulse.dts new file mode 100644 index 000000000000..f52e872ac96f --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mq-hummingboard-pulse.dts @@ -0,0 +1,256 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright (C) 2018 Jon Nettleton <jon@solid-run.com> + */ + +/dts-v1/; + +#include "dt-bindings/usb/pd.h" +#include "imx8mq-sr-som.dtsi" + +/ { + model = "SolidRun i.MX8MQ HummingBoard Pulse"; + compatible = "solidrun,hummingboard-pulse", "fsl,imx8mq"; + + chosen { + stdout-path = &uart1; + }; + + reg_usdhc2_vmmc: regulator-usdhc2-vmmc { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc2_vmmc>; + regulator-name = "VSD_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio1 13 GPIO_ACTIVE_LOW>; + }; + + reg_v_5v0: regulator-v-5v0 { + compatible = "regulator-fixed"; + regulator-name = "v_5v0"; + regulator-max-microvolt = <5000000>; + regulator-min-microvolt = <5000000>; + regulator-always-on; + }; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + clock-frequency = <100000>; + status = "okay"; + + typec_ptn5100: usb-typec@50 { + compatible = "nxp,ptn5110"; + reg = <0x50>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_typec>; + interrupt-parent = <&gpio1>; + interrupts = <6 IRQ_TYPE_LEVEL_LOW>; + + connector { + compatible = "usb-c-connector"; + label = "USB-C"; + data-role = "dual"; + power-role = "dual"; + try-power-role = "sink"; + source-pdos = <PDO_FIXED(5000, 2000, + PDO_FIXED_USB_COMM | + PDO_FIXED_SUSPEND | + PDO_FIXED_EXTPOWER)>; + sink-pdos = <PDO_FIXED(5000, 2000, + PDO_FIXED_USB_COMM | + PDO_FIXED_SUSPEND | + PDO_FIXED_EXTPOWER) + PDO_FIXED(9000, 2000, + PDO_FIXED_USB_COMM | + PDO_FIXED_SUSPEND | + PDO_FIXED_EXTPOWER)>; + op-sink-microwatt = <9000000>; + + port { + typec1_dr_sw: endpoint { + remote-endpoint = <&usb1_drd_sw>; + }; + }; + }; + }; +}; + +&i2c3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + clock-frequency = <100000>; + status = "okay"; + + rtc@69 { + compatible = "abracon,ab1805"; + reg = <0x69>; + abracon,tc-diode = "schottky"; + abracon,tc-resistor = <3>; + }; +}; + +&uart2 { /* J35 header */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + assigned-clocks = <&clk IMX8MQ_CLK_UART2>; + assigned-clock-parents = <&clk IMX8MQ_CLK_25M>; + status = "okay"; +}; + +&uart3 { /* Mikrobus */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + assigned-clocks = <&clk IMX8MQ_CLK_UART3>; + assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_80M>; + uart-has-rtscts; + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>; + cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>; + vmmc-supply = <®_usdhc2_vmmc>; + status = "okay"; +}; + +&usb_dwc3_0 { + dr_mode = "otg"; + status = "okay"; + + port { + usb1_drd_sw: endpoint { + remote-endpoint = <&typec1_dr_sw>; + }; + }; +}; + +&usb_dwc3_1 { + dr_mode = "host"; + status = "okay"; +}; + +&usb3_phy0 { + status = "okay"; +}; + +&usb3_phy1 { + status = "okay"; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + pinctrl_hog: hoggrp { + fsl,pins = < + /* MikroBus Analog */ + MX8MQ_IOMUXC_NAND_DATA05_GPIO3_IO11 0x41 + /* MikroBus Reset */ + MX8MQ_IOMUXC_SAI2_RXD0_GPIO4_IO23 0x41 + /* + * The following 2 pins need to be commented out and + * reconfigured to enable RTS/CTS on UART3 + */ + /* MikroBus PWM */ + MX8MQ_IOMUXC_ECSPI1_MISO_GPIO5_IO8 0x41 + /* MikroBus INT */ + MX8MQ_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x41 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX8MQ_IOMUXC_I2C2_SCL_I2C2_SCL 0x4000007f + MX8MQ_IOMUXC_I2C2_SDA_I2C2_SDA 0x4000007f + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX8MQ_IOMUXC_I2C3_SCL_I2C3_SCL 0x4000007f + MX8MQ_IOMUXC_I2C3_SDA_I2C3_SDA 0x4000007f + >; + }; + + pinctrl_typec: typecgrp { + fsl,pins = < + MX8MQ_IOMUXC_NAND_RE_B_GPIO3_IO15 0x16 + MX8MQ_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x17059 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX8MQ_IOMUXC_UART2_TXD_UART2_DCE_TX 0x49 + MX8MQ_IOMUXC_UART2_RXD_UART2_DCE_RX 0x49 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX8MQ_IOMUXC_UART3_TXD_UART3_DCE_TX 0x49 + MX8MQ_IOMUXC_UART3_RXD_UART3_DCE_RX 0x49 + /* + * These pins are by default GPIO on the Mikro Bus + * Header. To use RTS/CTS on UART3 comment them out + * of the hoggrp and enable them here + */ + /* MX8MQ_IOMUXC_ECSPI1_MISO_UART3_DCE_CTS_B 0x49 */ + /* MX8MQ_IOMUXC_ECSPI1_SS0_UART3_DCE_RTS_B 0x49 */ + >; + }; + + pinctrl_usdhc2_gpio: usdhc2grpgpio { + fsl,pins = < + MX8MQ_IOMUXC_SD2_CD_B_GPIO2_IO12 0x41 + >; + }; + + pinctrl_usdhc2_vmmc: usdhc2vmmcgpio { + fsl,pins = < + MX8MQ_IOMUXC_GPIO1_IO13_GPIO1_IO13 0x41 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x83 + MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xc3 + MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xc3 + MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xc3 + MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xc3 + MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xc3 + MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1 + >; + }; + + pinctrl_usdhc2_100mhz: usdhc2grp100mhz { + fsl,pins = < + MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x8d + MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xcd + MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xcd + MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xcd + MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xcd + MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xcd + MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1 + >; + }; + + pinctrl_usdhc2_200mhz: usdhc2grp200mhz { + fsl,pins = < + MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x9f + MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xdf + MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xdf + MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xdf + MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xdf + MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xdf + MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1 + >; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts index 5179e22f5126..683a11035643 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts +++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts @@ -174,6 +174,10 @@ assigned-clock-rates = <786432000>, <722534400>; }; +&dphy { + status = "okay"; +}; + &fec1 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_fec1>; diff --git a/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts b/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts new file mode 100644 index 000000000000..c832bf0fcc60 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts @@ -0,0 +1,405 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright 2018 Boundary Devices + */ + +/dts-v1/; + +#include <dt-bindings/input/input.h> +#include "imx8mq.dtsi" + +/ { + model = "Boundary Devices i.MX8MQ Nitrogen8M"; + compatible = "boundary,imx8mq-nitrogen8m", "fsl,imx8mq"; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory@40000000 { + device_type = "memory"; + reg = <0x00000000 0x40000000 0 0x80000000>; + }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_keys>; + + power { + label = "Power Button"; + gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; + linux,code = <KEY_POWER>; + wakeup-source; + }; + }; + + reg_vref_0v9: regulator-vref-0v9 { + compatible = "regulator-fixed"; + regulator-name = "vref-0v9"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + }; + + reg_vref_1v8: regulator-vref-1v8 { + compatible = "regulator-fixed"; + regulator-name = "vref-1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + reg_vref_2v5: regulator-vref-2v5 { + compatible = "regulator-fixed"; + regulator-name = "vref-2v5"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + }; + + reg_vref_3v3: regulator-vref-3v3 { + compatible = "regulator-fixed"; + regulator-name = "vref-3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + reg_vref_5v: regulator-vref-5v { + compatible = "regulator-fixed"; + regulator-name = "vref-5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; +}; + + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec1>; + phy-mode = "rgmii-id"; + phy-handle = <ðphy0>; + fsl,magic-packet; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@4 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <4>; + interrupts-extended = <&gpio1 11 IRQ_TYPE_LEVEL_LOW>; + }; + }; +}; + +&i2c1 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + i2cmux@70 { + compatible = "nxp,pca9546"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1_pca9546>; + reg = <0x70>; + reset-gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; + #address-cells = <1>; + #size-cells = <0>; + + i2c1a: i2c1@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + + reg_arm_dram: regulator@60 { + compatible = "fcs,fan53555"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_arm_dram>; + reg = <0x60>; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + vsel-gpios = <&gpio3 24 GPIO_ACTIVE_HIGH>; + }; + }; + + i2c1b: i2c1@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + reg_dram_1p1v: regulator@60 { + compatible = "fcs,fan53555"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_dram_1p1v>; + reg = <0x60>; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + vsel-gpios = <&gpio2 11 GPIO_ACTIVE_HIGH>; + }; + }; + + i2c1c: i2c1@2 { + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + + reg_soc_gpu_vpu: regulator@60 { + compatible = "fcs,fan53555"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_soc_gpu_vpu>; + reg = <0x60>; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + vsel-gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>; + }; + }; + + i2c1d: i2c1@3 { + reg = <3>; + #address-cells = <1>; + #size-cells = <0>; + + rtc@68 { + compatible = "microcrystal,rv4162"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1d_rv4162>; + reg = <0x68>; + interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_LOW>; + wakeup-source; + }; + }; + }; +}; + +&uart1 { /* console */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + assigned-clocks = <&clk IMX8MQ_CLK_UART1>; + assigned-clock-parents = <&clk IMX8MQ_CLK_25M>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + assigned-clocks = <&clk IMX8MQ_CLK_UART2>; + assigned-clock-parents = <&clk IMX8MQ_CLK_25M>; + status = "okay"; +}; + +&usdhc1 { + bus-width = <8>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc1>; + non-removable; + vmmc-supply = <®_vref_1v8>; + status = "okay"; +}; + +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>; + fsl,ext-reset-output; + status = "okay"; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + pinctrl_hog: hoggrp { + fsl,pins = < + /* J17 connector, odd */ + MX8MQ_IOMUXC_SAI1_RXFS_GPIO4_IO0 0x19 /* Pin 19 */ + MX8MQ_IOMUXC_SAI1_RXC_GPIO4_IO1 0x19 /* Pin 21 */ + MX8MQ_IOMUXC_SAI1_RXD1_GPIO4_IO3 0x19 /* Pin 23 */ + MX8MQ_IOMUXC_SAI1_RXD2_GPIO4_IO4 0x19 /* Pin 25 */ + MX8MQ_IOMUXC_SAI1_RXD3_GPIO4_IO5 0x19 /* Pin 27 */ + MX8MQ_IOMUXC_SAI1_RXD4_GPIO4_IO6 0x19 /* Pin 29 */ + MX8MQ_IOMUXC_SAI1_RXD5_GPIO4_IO7 0x19 /* Pin 31 */ + MX8MQ_IOMUXC_SAI1_RXD6_GPIO4_IO8 0x19 /* Pin 33 */ + MX8MQ_IOMUXC_SAI1_RXD7_GPIO4_IO9 0x19 /* Pin 35 */ + MX8MQ_IOMUXC_SAI1_TXD1_GPIO4_IO13 0x19 /* Pin 39 */ + MX8MQ_IOMUXC_SAI1_TXD2_GPIO4_IO14 0x19 /* Pin 41 */ + MX8MQ_IOMUXC_SAI1_TXD3_GPIO4_IO15 0x19 /* Pin 43 */ + MX8MQ_IOMUXC_SAI1_TXD4_GPIO4_IO16 0x19 /* Pin 45 */ + MX8MQ_IOMUXC_SAI1_TXD5_GPIO4_IO17 0x19 /* Pin 47 */ + MX8MQ_IOMUXC_SAI1_TXD6_GPIO4_IO18 0x19 /* Pin 49 */ + MX8MQ_IOMUXC_SAI1_TXD7_GPIO4_IO19 0x19 /* Pin 51 */ + + /* J17 connector, even */ + MX8MQ_IOMUXC_SAI3_RXFS_GPIO4_IO28 0x19 /* Pin 44 */ + MX8MQ_IOMUXC_SAI3_RXC_GPIO4_IO29 0x19 /* Pin 48 */ + MX8MQ_IOMUXC_GPIO1_IO10_GPIO1_IO10 0x19 /* Pin 50 */ + MX8MQ_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x19 /* Pin 54 */ + MX8MQ_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x19 /* Pin 56 */ + + /* J18 connector, odd */ + MX8MQ_IOMUXC_NAND_CE3_B_GPIO3_IO4 0x19 /* Pin 41 */ + MX8MQ_IOMUXC_NAND_CLE_GPIO3_IO5 0x19 /* Pin 43 */ + MX8MQ_IOMUXC_NAND_READY_B_GPIO3_IO16 0x19 /* Pin 45 */ + MX8MQ_IOMUXC_NAND_DATA05_GPIO3_IO11 0x19 /* Pin 47 */ + MX8MQ_IOMUXC_NAND_WP_B_GPIO3_IO18 0x19 /* Pin 49 */ + MX8MQ_IOMUXC_NAND_DQS_GPIO3_IO14 0x19 /* Pin 53 */ + + /* J18 connector, even */ + MX8MQ_IOMUXC_NAND_ALE_GPIO3_IO0 0x19 /* Pin 32 */ + MX8MQ_IOMUXC_NAND_CE0_B_GPIO3_IO1 0x19 /* Pin 36 */ + MX8MQ_IOMUXC_NAND_DATA00_GPIO3_IO6 0x19 /* Pin 38 */ + MX8MQ_IOMUXC_NAND_DATA01_GPIO3_IO7 0x19 /* Pin 40 */ + MX8MQ_IOMUXC_NAND_DATA02_GPIO3_IO8 0x19 /* Pin 42 */ + MX8MQ_IOMUXC_NAND_DATA03_GPIO3_IO9 0x19 /* Pin 44 */ + MX8MQ_IOMUXC_NAND_DATA04_GPIO3_IO10 0x19 /* Pin 46 */ + + /* J13 Pin 2, WL_WAKE */ + MX8MQ_IOMUXC_SAI5_RXD2_GPIO3_IO23 0xd6 + /* J13 Pin 4, WL_IRQ, not needed for Silex */ + MX8MQ_IOMUXC_SAI5_RXD0_GPIO3_IO21 0xd6 + /* J13 pin 9, unused */ + MX8MQ_IOMUXC_SD2_CD_B_GPIO2_IO12 0x19 + /* J13 Pin 41, BT_CLK_REQ */ + MX8MQ_IOMUXC_SAI5_RXD1_GPIO3_IO22 0xd6 + /* J13 Pin 42, BT_HOST_WAKE */ + MX8MQ_IOMUXC_SAI5_MCLK_GPIO3_IO25 0xd6 + + /* Clock for both CSI1 and CSI2 */ + MX8MQ_IOMUXC_GPIO1_IO15_CCMSRCGPCMIX_CLKO2 0x07 + /* test points */ + MX8MQ_IOMUXC_GPIO1_IO04_GPIO1_IO4 0xc1 /* TP87 */ + >; + }; + + pinctrl_fec1: fec1grp { + fsl,pins = < + MX8MQ_IOMUXC_ENET_MDC_ENET1_MDC 0x3 + MX8MQ_IOMUXC_ENET_MDIO_ENET1_MDIO 0x23 + MX8MQ_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f + MX8MQ_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f + MX8MQ_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f + MX8MQ_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f + MX8MQ_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f + MX8MQ_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f + MX8MQ_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91 + MX8MQ_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91 + MX8MQ_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91 + MX8MQ_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91 + MX8MQ_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91 + MX8MQ_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91 + MX8MQ_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x19 + MX8MQ_IOMUXC_GPIO1_IO11_GPIO1_IO11 0x59 + >; + }; + + pinctrl_gpio_keys: gpio-keysgrp { + fsl,pins = < + MX8MQ_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x19 + >; + }; + + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL 0x4000007f + MX8MQ_IOMUXC_I2C1_SDA_I2C1_SDA 0x4000007f + >; + }; + + pinctrl_i2c1_pca9546: i2c1-pca9546grp { + fsl,pins = < + MX8MQ_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x49 + >; + }; + + pinctrl_i2c1d_rv4162: i2c1d-rv4162grp { + fsl,pins = < + MX8MQ_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x49 + >; + }; + + pinctrl_reg_arm_dram: reg-arm-dramgrp { + fsl,pins = < + MX8MQ_IOMUXC_SAI5_RXD3_GPIO3_IO24 0x16 + >; + }; + + pinctrl_reg_dram_1p1v: reg-dram-1p1vgrp { + fsl,pins = < + MX8MQ_IOMUXC_SD1_STROBE_GPIO2_IO11 0x16 + >; + }; + + pinctrl_reg_soc_gpu_vpu: reg-soc-gpu-vpugrp { + fsl,pins = < + MX8MQ_IOMUXC_SD2_WP_GPIO2_IO20 0x16 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX8MQ_IOMUXC_UART1_RXD_UART1_DCE_RX 0x45 + MX8MQ_IOMUXC_UART1_TXD_UART1_DCE_TX 0x45 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX8MQ_IOMUXC_UART2_RXD_UART2_DCE_RX 0x45 + MX8MQ_IOMUXC_UART2_TXD_UART2_DCE_TX 0x45 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x83 + MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xc3 + MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc3 + MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc3 + MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc3 + MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc3 + MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xc3 + MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xc3 + MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xc3 + MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xc3 + MX8MQ_IOMUXC_SD1_RESET_B_GPIO2_IO10 0x41 + >; + }; + + pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp { + fsl,pins = < + MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x8d + MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xcd + MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xcd + MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xcd + MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xcd + MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xcd + MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xcd + MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xcd + MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xcd + MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xcd + >; + }; + + pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp { + fsl,pins = < + MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x9f + MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xdf + MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xdf + MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xdf + MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xdf + MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xdf + MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xdf + MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xdf + MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xdf + MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xdf + >; + }; + + pinctrl_wdog: wdoggrp { + fsl,pins = < + MX8MQ_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6 + >; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mq-pico-pi.dts b/arch/arm64/boot/dts/freescale/imx8mq-pico-pi.dts new file mode 100644 index 000000000000..8a4aee2348ee --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mq-pico-pi.dts @@ -0,0 +1,413 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2018 Wandboard, Org. + * Copyright 2017 NXP + * + * Author: Richard Hu <hakahu@gmail.com> + */ + +/dts-v1/; + +#include "imx8mq.dtsi" + +/ { + model = "TechNexion PICO-PI-8M"; + compatible = "technexion,pico-pi-imx8m", "fsl,imx8mq"; + + chosen { + stdout-path = &uart1; + }; + + pmic_osc: clock-pmic { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + clock-output-names = "pmic_osc"; + }; + + reg_usb_otg_vbus: regulator-usb-otg-vbus { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_otg_vbus>; + compatible = "regulator-fixed"; + regulator-name = "usb_otg_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio3 14 GPIO_ACTIVE_LOW>; + }; +}; + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec1 &pinctrl_enet_3v3>; + phy-mode = "rgmii-id"; + phy-handle = <ðphy0>; + fsl,magic-packet; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; + }; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + pmic: pmic@4b { + reg = <0x4b>; + compatible = "rohm,bd71837"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pmic>; + clocks = <&pmic_osc>; + clock-names = "osc"; + clock-output-names = "pmic_clk"; + interrupt-parent = <&gpio1>; + interrupts = <3 GPIO_ACTIVE_LOW>; + interrupt-names = "irq"; + + regulators { + buck1: BUCK1 { + regulator-name = "buck1"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + regulator-boot-on; + regulator-ramp-delay = <1250>; + rohm,dvs-run-voltage = <900000>; + rohm,dvs-idle-voltage = <850000>; + rohm,dvs-suspend-voltage = <800000>; + }; + + buck2: BUCK2 { + regulator-name = "buck2"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + regulator-boot-on; + regulator-ramp-delay = <1250>; + rohm,dvs-run-voltage = <1000000>; + rohm,dvs-idle-voltage = <900000>; + }; + + buck3: BUCK3 { + regulator-name = "buck3"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + regulator-boot-on; + rohm,dvs-run-voltage = <1000000>; + }; + + buck4: BUCK4 { + regulator-name = "buck4"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + regulator-boot-on; + rohm,dvs-run-voltage = <1000000>; + }; + + buck5: BUCK5 { + regulator-name = "buck5"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1350000>; + regulator-boot-on; + }; + + buck6: BUCK6 { + regulator-name = "buck6"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + + buck7: BUCK7 { + regulator-name = "buck7"; + regulator-min-microvolt = <1605000>; + regulator-max-microvolt = <1995000>; + regulator-boot-on; + }; + + buck8: BUCK8 { + regulator-name = "buck8"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1400000>; + regulator-boot-on; + }; + + ldo1: LDO1 { + regulator-name = "ldo1"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo2: LDO2 { + regulator-name = "ldo2"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo3: LDO3 { + regulator-name = "ldo3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + + ldo4: LDO4 { + regulator-name = "ldo4"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + }; + + ldo5: LDO5 { + regulator-name = "ldo5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + + ldo6: LDO6 { + regulator-name = "ldo6"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + }; + + ldo7: LDO7 { + regulator-name = "ldo7"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + }; + }; +}; + +&i2c2 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; +}; + +&uart1 { /* console */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&usdhc1 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc1>; + pinctrl-1 = <&pinctrl_usdhc1_100mhz>; + pinctrl-2 = <&pinctrl_usdhc1_200mhz>; + bus-width = <8>; + non-removable; + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>; + bus-width = <4>; + cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>; + status = "okay"; +}; + +&usb3_phy0 { + status = "okay"; +}; + +&usb3_phy1 { + status = "okay"; +}; + +&usb_dwc3_1 { + dr_mode = "host"; + status = "okay"; +}; + +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>; + fsl,ext-reset-output; + status = "okay"; +}; + +&iomuxc { + pinctrl_enet_3v3: enet3v3grp { + fsl,pins = < + MX8MQ_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x19 + >; + }; + + pinctrl_fec1: fec1grp { + fsl,pins = < + MX8MQ_IOMUXC_ENET_MDC_ENET1_MDC 0x3 + MX8MQ_IOMUXC_ENET_MDIO_ENET1_MDIO 0x23 + MX8MQ_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f + MX8MQ_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f + MX8MQ_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f + MX8MQ_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f + MX8MQ_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91 + MX8MQ_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91 + MX8MQ_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91 + MX8MQ_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91 + MX8MQ_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f + MX8MQ_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91 + MX8MQ_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91 + MX8MQ_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f + MX8MQ_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x19 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL 0x4000007f + MX8MQ_IOMUXC_I2C1_SDA_I2C1_SDA 0x4000007f + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX8MQ_IOMUXC_I2C2_SCL_I2C2_SCL 0x4000007f + MX8MQ_IOMUXC_I2C2_SDA_I2C2_SDA 0x4000007f + >; + }; + + pinctrl_otg_vbus: otgvbusgrp { + fsl,pins = < + MX8MQ_IOMUXC_NAND_DQS_GPIO3_IO14 0x19 /* USB OTG VBUS Enable */ + >; + }; + + pinctrl_pmic: pmicirq { + fsl,pins = < + MX8MQ_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x41 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX8MQ_IOMUXC_UART1_RXD_UART1_DCE_RX 0x49 + MX8MQ_IOMUXC_UART1_TXD_UART1_DCE_TX 0x49 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX8MQ_IOMUXC_UART2_RXD_UART2_DCE_RX 0x49 + MX8MQ_IOMUXC_UART2_TXD_UART2_DCE_TX 0x49 + MX8MQ_IOMUXC_UART4_RXD_UART2_DCE_CTS_B 0x49 + MX8MQ_IOMUXC_UART4_TXD_UART2_DCE_RTS_B 0x49 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x83 + MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xc3 + MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc3 + MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc3 + MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc3 + MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc3 + MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xc3 + MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xc3 + MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xc3 + MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xc3 + MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x83 + >; + }; + + pinctrl_usdhc1_100mhz: usdhc1grp100mhz { + fsl,pins = < + MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x85 + MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xc5 + MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc5 + MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc5 + MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc5 + MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc5 + MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xc5 + MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xc5 + MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xc5 + MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xc5 + MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x85 + >; + }; + + pinctrl_usdhc1_200mhz: usdhc1grp200mhz { + fsl,pins = < + MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x87 + MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xc7 + MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc7 + MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc7 + MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc7 + MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc7 + MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xc7 + MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xc7 + MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xc7 + MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xc7 + MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x87 + >; + }; + + pinctrl_usdhc2_gpio: usdhc2grpgpio { + fsl,pins = < + MX8MQ_IOMUXC_SD2_CD_B_GPIO2_IO12 0x41 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x83 + MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xc3 + MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xc3 + MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xc3 + MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xc3 + MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xc3 + MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1 + >; + }; + + pinctrl_usdhc2_100mhz: usdhc2grp100mhz { + fsl,pins = < + MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x85 + MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xc5 + MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xc5 + MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xc5 + MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xc5 + MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xc5 + MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1 + >; + }; + + pinctrl_usdhc2_200mhz: usdhc2grp200mhz { + fsl,pins = < + MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x87 + MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xc7 + MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xc7 + MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xc7 + MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xc7 + MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xc7 + MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1 + >; + }; + + pinctrl_wdog: wdoggrp { + fsl,pins = < + MX8MQ_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6 + >; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mq-sr-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-sr-som.dtsi new file mode 100644 index 000000000000..d7f03c65832b --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mq-sr-som.dtsi @@ -0,0 +1,309 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright (C) 2018 Jon Nettleton <jon@solid-run.com> + */ + +#include "imx8mq.dtsi" + +/ { + reg_vdd_3v3: regulator-vdd-3v3 { + compatible = "regulator-fixed"; + regulator-always-on; + regulator-name = "vdd_3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; +}; + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec1>; + phy-mode = "rgmii-id"; + phy-handle = <ðphy0>; + phy-reset-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; + phy-reset-duration = <2>; + fsl,magic-packet; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@4 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <4>; + }; + }; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + clock-frequency = <400000>; + status = "okay"; + + pmic: pmic@8 { + compatible = "fsl,pfuze100"; + reg = <0x08>; + + regulators { + sw1a_reg: sw1ab { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + }; + + sw1c_reg: sw1c { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + }; + + sw2_reg: sw2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + sw3a_reg: sw3ab { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-always-on; + }; + + sw4_reg: sw4 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + swbst_reg: swbst { + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5150000>; + }; + + snvs_reg: vsnvs { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + regulator-always-on; + }; + + vref_reg: vrefddr { + regulator-always-on; + }; + + vgen1_reg: vgen1 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vgen2_reg: vgen2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + regulator-always-on; + }; + + vgen3_reg: vgen3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen4_reg: vgen4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen5_reg: vgen5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen6_reg: vgen6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + }; + }; +}; + +&pgc_gpu{ + power-supply = <&sw1a_reg>; +}; + +&pgc_vpu { + power-supply = <&sw1c_reg>; +}; + +&qspi0 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_qspi>; + status = "okay"; + + /* SPI flash; not assembled by default */ + spi_flash: flash@0 { + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; + compatible = "micron,n25q256a", "jedec,spi-nor"; + spi-max-frequency = <29000000>; + status = "disabled"; + }; +}; + +&uart1 { /* console */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + assigned-clocks = <&clk IMX8MQ_CLK_UART1>; + assigned-clock-parents = <&clk IMX8MQ_CLK_25M>; + assigned-clock-rates = <25000000>; + status = "okay"; +}; + +&uart4 { /* ublox BT */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4>; + assigned-clocks = <&clk IMX8MQ_CLK_UART4>; + assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_80M>; + assigned-clock-rates = <80000000>; + status = "okay"; +}; + +&usdhc1 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc1>; + pinctrl-1 = <&pinctrl_usdhc1_100mhz>; + pinctrl-2 = <&pinctrl_usdhc1_200mhz>; + bus-width = <8>; + non-removable; + status = "okay"; +}; + +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>; + fsl,ext-reset-output; + status = "okay"; +}; + +&iomuxc { + pinctrl_fec1: fec1grp { + fsl,pins = < + MX8MQ_IOMUXC_ENET_MDC_ENET1_MDC 0x3 + MX8MQ_IOMUXC_ENET_MDIO_ENET1_MDIO 0x23 + MX8MQ_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f + MX8MQ_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f + MX8MQ_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f + MX8MQ_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f + MX8MQ_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91 + MX8MQ_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91 + MX8MQ_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91 + MX8MQ_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91 + MX8MQ_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f + MX8MQ_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91 + MX8MQ_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91 + MX8MQ_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f + MX8MQ_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x19 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL 0x4000007f + MX8MQ_IOMUXC_I2C1_SDA_I2C1_SDA 0x4000007f + >; + }; + + pinctrl_pcie0: pcie0grp { + fsl,pins = < + MX8MQ_IOMUXC_I2C4_SCL_PCIE1_CLKREQ_B 0x74 + MX8MQ_IOMUXC_SPDIF_EXT_CLK_GPIO5_IO5 0x16 + MX8MQ_IOMUXC_SAI2_RXFS_GPIO4_IO21 0x16 + >; + }; + + pinctrl_qspi: qspigrp { + fsl,pins = < + MX8MQ_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x82 + MX8MQ_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x82 + MX8MQ_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x82 + MX8MQ_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x82 + MX8MQ_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x82 + MX8MQ_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x82 + + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX8MQ_IOMUXC_UART1_RXD_UART1_DCE_RX 0x49 + MX8MQ_IOMUXC_UART1_TXD_UART1_DCE_TX 0x49 + MX8MQ_IOMUXC_NAND_CE1_B_GPIO3_IO2 0x19 + >; + }; + + pinctrl_uart4: uart4grp { + fsl,pins = < + MX8MQ_IOMUXC_UART4_TXD_UART4_DCE_TX 0x49 + MX8MQ_IOMUXC_UART4_RXD_UART4_DCE_RX 0x49 + MX8MQ_IOMUXC_SAI3_TXD_GPIO5_IO1 0x19 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x83 + MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xc3 + MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc3 + MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc3 + MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc3 + MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc3 + MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xc3 + MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xc3 + MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xc3 + MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xc3 + MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x83 + MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1 + >; + }; + + pinctrl_usdhc1_100mhz: usdhc1grp100mhz { + fsl,pins = < + MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x8d + MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xcd + MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xcd + MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xcd + MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xcd + MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xcd + MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xcd + MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xcd + MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xcd + MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xcd + MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x8d + MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1 + >; + }; + + pinctrl_usdhc1_200mhz: usdhc1grp200mhz { + fsl,pins = < + MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x9f + MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xdf + MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xdf + MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xdf + MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xdf + MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xdf + MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xdf + MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xdf + MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xdf + MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xdf + MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x9f + MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1 + >; + }; + + pinctrl_wdog: wdoggrp { + fsl,pins = < + MX8MQ_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6 + >; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra.dtsi index 7a1706f969f0..af99473ada04 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra.dtsi @@ -68,18 +68,6 @@ regulator-always-on; }; - reg_5p0_user_usb: regulator-5p0-user-usb { - compatible = "regulator-fixed"; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_reg_user_usb>; - vin-supply = <®_5p0_main>; - regulator-name = "5V_USER_USB"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - gpio = <&gpio3 12 GPIO_ACTIVE_LOW>; - startup-delay-us = <1000>; - }; - reg_usdhc2_vmmc: regulator-vsd-3v3 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_reg_usdhc2>; @@ -244,6 +232,13 @@ line-name = "usb-mode1"; }; + usb-pwr { + gpio-hog; + gpios = <12 GPIO_ACTIVE_LOW>; + output-high; + line-name = "usb-pwr-ctrl-en-n"; + }; + usb-mode2 { gpio-hog; gpios = <13 GPIO_ACTIVE_HIGH>; @@ -257,6 +252,17 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_i2c1>; status = "okay"; + + ucs1002: charger@32 { + compatible = "microchip,ucs1002"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ucs1002>; + reg = <0x32>; + interrupt-parent = <&gpio3>; + interrupts = <17 IRQ_TYPE_EDGE_BOTH>, + <18 IRQ_TYPE_EDGE_BOTH>; + interrupt-names = "a_det", "alert"; + }; }; &i2c2 { @@ -428,7 +434,7 @@ }; &usb3_phy0 { - vbus-supply = <®_5p0_user_usb>; + vbus-supply = <&ucs1002>; status = "okay"; }; @@ -532,6 +538,7 @@ fsl,pins = < MX8MQ_IOMUXC_NAND_DATA04_GPIO3_IO10 0x6 MX8MQ_IOMUXC_NAND_DATA05_GPIO3_IO11 0x6 + MX8MQ_IOMUXC_NAND_DATA06_GPIO3_IO12 0x6 MX8MQ_IOMUXC_NAND_DATA07_GPIO3_IO13 0x6 >; }; @@ -597,12 +604,6 @@ >; }; - pinctrl_reg_user_usb: reguserusbgrp { - fsl,pins = < - MX8MQ_IOMUXC_NAND_DATA06_GPIO3_IO12 0x6 - >; - }; - pinctrl_switch_irq: switchgrp { fsl,pins = < MX8MQ_IOMUXC_GPIO1_IO15_GPIO1_IO15 0x41 @@ -630,6 +631,13 @@ >; }; + pinctrl_ucs1002: ucs1002grp { + fsl,pins = < + MX8MQ_IOMUXC_NAND_WE_B_GPIO3_IO17 0x41 + MX8MQ_IOMUXC_NAND_WP_B_GPIO3_IO18 0x41 + >; + }; + pinctrl_usbhub: usbhubgrp { fsl,pins = < MX8MQ_IOMUXC_SAI5_MCLK_GPIO3_IO25 0x41 diff --git a/arch/arm64/boot/dts/freescale/imx8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq.dtsi index 52aae341d0da..046a0c8c8dd5 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mq.dtsi @@ -156,6 +156,7 @@ /* Industrial only */ opp-supported-hw = <0xf>, <0x4>; clock-latency-ns = <150000>; + opp-suspend; }; opp-1000000000 { @@ -164,21 +165,23 @@ /* Consumer only */ opp-supported-hw = <0xe>, <0x3>; clock-latency-ns = <150000>; + opp-suspend; }; opp-1300000000 { opp-hz = /bits/ 64 <1300000000>; opp-microvolt = <1000000>; - opp-supported-hw = <0xc>, <0x7>; + opp-supported-hw = <0xc>, <0x4>; clock-latency-ns = <150000>; + opp-suspend; }; opp-1500000000 { opp-hz = /bits/ 64 <1500000000>; opp-microvolt = <1000000>; - /* Consumer only but rely on speed grading */ - opp-supported-hw = <0x8>, <0x7>; + opp-supported-hw = <0x8>, <0x3>; clock-latency-ns = <150000>; + opp-suspend; }; }; @@ -288,6 +291,7 @@ #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; + gpio-ranges = <&iomuxc 0 10 30>; }; gpio2: gpio@30210000 { @@ -300,6 +304,7 @@ #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; + gpio-ranges = <&iomuxc 0 40 21>; }; gpio3: gpio@30220000 { @@ -312,6 +317,7 @@ #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; + gpio-ranges = <&iomuxc 0 61 26>; }; gpio4: gpio@30230000 { @@ -324,6 +330,7 @@ #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; + gpio-ranges = <&iomuxc 0 87 32>; }; gpio5: gpio@30240000 { @@ -336,12 +343,14 @@ #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; + gpio-ranges = <&iomuxc 0 119 30>; }; tmu: tmu@30260000 { compatible = "fsl,imx8mq-tmu"; reg = <0x30260000 0x10000>; interrupt = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk IMX8MQ_CLK_TMU_ROOT>; little-endian; fsl,tmu-range = <0xb0000 0xa0026 0x80048 0x70061>; fsl,tmu-calibration = <0x00000000 0x00000023 @@ -431,8 +440,15 @@ }; iomuxc_gpr: syscon@30340000 { - compatible = "fsl,imx8mq-iomuxc-gpr", "fsl,imx6q-iomuxc-gpr", "syscon"; + compatible = "fsl,imx8mq-iomuxc-gpr", "fsl,imx6q-iomuxc-gpr", + "syscon", "simple-mfd"; reg = <0x30340000 0x10000>; + + mux: mux-controller { + compatible = "mmio-mux"; + #mux-control-cells = <1>; + mux-reg-masks = <0x34 0x00000004>; /* MIPI_MUX_SEL */ + }; }; ocotp: ocotp-ctrl@30350000 { @@ -727,6 +743,19 @@ status = "disabled"; }; + dphy: dphy@30a00300 { + compatible = "fsl,imx8mq-mipi-dphy"; + reg = <0x30a00300 0x100>; + clocks = <&clk IMX8MQ_CLK_DSI_PHY_REF>; + clock-names = "phy_ref"; + assigned-clocks = <&clk IMX8MQ_CLK_DSI_PHY_REF>; + assigned-clock-parents = <&clk IMX8MQ_VIDEO_PLL1_OUT>; + assigned-clock-rates = <24000000>; + #phy-cells = <0>; + power-domains = <&pgc_mipi>; + status = "disabled"; + }; + i2c1: i2c@30a20000 { compatible = "fsl,imx8mq-i2c", "fsl,imx21-i2c"; reg = <0x30a20000 0x10000>; @@ -900,9 +929,9 @@ usb_dwc3_0: usb@38100000 { compatible = "fsl,imx8mq-dwc3", "snps,dwc3"; reg = <0x38100000 0x10000>; - clocks = <&clk IMX8MQ_CLK_USB_BUS>, + clocks = <&clk IMX8MQ_CLK_USB1_CTRL_ROOT>, <&clk IMX8MQ_CLK_USB_CORE_REF>, - <&clk IMX8MQ_CLK_USB1_CTRL_ROOT>; + <&clk IMX8MQ_CLK_32K>; clock-names = "bus_early", "ref", "suspend"; assigned-clocks = <&clk IMX8MQ_CLK_USB_BUS>, <&clk IMX8MQ_CLK_USB_CORE_REF>; @@ -932,9 +961,9 @@ usb_dwc3_1: usb@38200000 { compatible = "fsl,imx8mq-dwc3", "snps,dwc3"; reg = <0x38200000 0x10000>; - clocks = <&clk IMX8MQ_CLK_USB_BUS>, + clocks = <&clk IMX8MQ_CLK_USB2_CTRL_ROOT>, <&clk IMX8MQ_CLK_USB_CORE_REF>, - <&clk IMX8MQ_CLK_USB2_CTRL_ROOT>; + <&clk IMX8MQ_CLK_32K>; clock-names = "bus_early", "ref", "suspend"; assigned-clocks = <&clk IMX8MQ_CLK_USB_BUS>, <&clk IMX8MQ_CLK_USB_CORE_REF>; @@ -1032,5 +1061,12 @@ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; interrupt-parent = <&gic>; }; + + ddr-pmu@3d800000 { + compatible = "fsl,imx8mq-ddr-pmu", "fsl,imx8m-ddr-pmu"; + reg = <0x3d800000 0x400000>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + }; }; }; diff --git a/arch/arm64/boot/dts/freescale/imx8qxp-ai_ml.dts b/arch/arm64/boot/dts/freescale/imx8qxp-ai_ml.dts new file mode 100644 index 000000000000..91eef9754101 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8qxp-ai_ml.dts @@ -0,0 +1,249 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2018 Einfochips + * Copyright 2019 Linaro Ltd. + */ + +/dts-v1/; + +#include "imx8qxp.dtsi" + +/ { + model = "Einfochips i.MX8QXP AI_ML"; + compatible = "einfochips,imx8qxp-ai_ml", "fsl,imx8qxp"; + + aliases { + serial1 = &adma_lpuart1; + serial2 = &adma_lpuart2; + serial3 = &adma_lpuart3; + }; + + chosen { + stdout-path = &adma_lpuart2; + }; + + memory@80000000 { + device_type = "memory"; + reg = <0x00000000 0x80000000 0 0x80000000>; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_leds>; + + user-led1 { + label = "green:user1"; + gpios = <&lsio_gpio4 16 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + + user-led2 { + label = "green:user2"; + gpios = <&lsio_gpio0 6 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "none"; + }; + + user-led3 { + label = "green:user3"; + gpios = <&lsio_gpio0 7 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc1"; + default-state = "off"; + }; + + user-led4 { + label = "green:user4"; + gpios = <&lsio_gpio4 21 GPIO_ACTIVE_HIGH>; + panic-indicator; + linux,default-trigger = "none"; + }; + + wlan-active-led { + label = "yellow:wlan"; + gpios = <&lsio_gpio4 17 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "phy0tx"; + default-state = "off"; + }; + + bt-active-led { + label = "blue:bt"; + gpios = <&lsio_gpio4 18 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "hci0-power"; + default-state = "off"; + }; + }; + + sdio_pwrseq: sdio-pwrseq { + compatible = "mmc-pwrseq-simple"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wifi_reg_on>; + reset-gpios = <&lsio_gpio3 24 GPIO_ACTIVE_LOW>; + }; +}; + +/* BT */ +&adma_lpuart0 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lpuart0>; + uart-has-rtscts; + status = "okay"; +}; + +/* LS-UART0 */ +&adma_lpuart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lpuart1>; + status = "okay"; +}; + +/* Debug */ +&adma_lpuart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lpuart2>; + status = "okay"; +}; + +/* PCI-E UART */ +&adma_lpuart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lpuart3>; + status = "okay"; +}; + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec1>; + phy-mode = "rgmii-id"; + phy-handle = <ðphy0>; + fsl,magic-packet; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + }; + }; +}; + +/* WiFi */ +&usdhc1 { + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc1>; + bus-width = <4>; + no-sd; + non-removable; + mmc-pwrseq = <&sdio_pwrseq>; + status = "okay"; + + brcmf: wifi@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + }; +}; + +/* SD */ +&usdhc2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc2>; + bus-width = <4>; + cd-gpios = <&lsio_gpio4 22 GPIO_ACTIVE_LOW>; + status = "okay"; +}; + +&iomuxc { + pinctrl_fec1: fec1grp { + fsl,pins = < + IMX8QXP_ENET0_MDC_CONN_ENET0_MDC 0x06000020 + IMX8QXP_ENET0_MDIO_CONN_ENET0_MDIO 0x06000020 + IMX8QXP_ENET0_RGMII_TX_CTL_CONN_ENET0_RGMII_TX_CTL 0x06000020 + IMX8QXP_ENET0_RGMII_TXC_CONN_ENET0_RGMII_TXC 0x06000020 + IMX8QXP_ENET0_RGMII_TXD0_CONN_ENET0_RGMII_TXD0 0x06000020 + IMX8QXP_ENET0_RGMII_TXD1_CONN_ENET0_RGMII_TXD1 0x06000020 + IMX8QXP_ENET0_RGMII_TXD2_CONN_ENET0_RGMII_TXD2 0x06000020 + IMX8QXP_ENET0_RGMII_TXD3_CONN_ENET0_RGMII_TXD3 0x06000020 + IMX8QXP_ENET0_RGMII_RXC_CONN_ENET0_RGMII_RXC 0x06000020 + IMX8QXP_ENET0_RGMII_RX_CTL_CONN_ENET0_RGMII_RX_CTL 0x06000020 + IMX8QXP_ENET0_RGMII_RXD0_CONN_ENET0_RGMII_RXD0 0x06000020 + IMX8QXP_ENET0_RGMII_RXD1_CONN_ENET0_RGMII_RXD1 0x06000020 + IMX8QXP_ENET0_RGMII_RXD2_CONN_ENET0_RGMII_RXD2 0x06000020 + IMX8QXP_ENET0_RGMII_RXD3_CONN_ENET0_RGMII_RXD3 0x06000020 + >; + }; + + pinctrl_leds: ledsgrp{ + fsl,pins = < + IMX8QXP_ESAI0_TX2_RX3_LSIO_GPIO0_IO06 0x00000021 + IMX8QXP_ESAI0_TX3_RX2_LSIO_GPIO0_IO07 0x00000021 + IMX8QXP_EMMC0_DATA7_LSIO_GPIO4_IO16 0x00000021 + IMX8QXP_USDHC1_WP_LSIO_GPIO4_IO21 0x00000021 + IMX8QXP_EMMC0_STROBE_LSIO_GPIO4_IO17 0x00000021 + IMX8QXP_EMMC0_RESET_B_LSIO_GPIO4_IO18 0x00000021 + >; + }; + + pinctrl_lpuart0: lpuart0grp { + fsl,pins = < + IMX8QXP_UART0_RX_ADMA_UART0_RX 0X06000020 + IMX8QXP_UART0_TX_ADMA_UART0_TX 0X06000020 + IMX8QXP_FLEXCAN0_TX_ADMA_UART0_CTS_B 0x06000020 + IMX8QXP_FLEXCAN0_RX_ADMA_UART0_RTS_B 0x06000020 + >; + }; + + pinctrl_lpuart1: lpuart1grp { + fsl,pins = < + IMX8QXP_UART1_RX_ADMA_UART1_RX 0X06000020 + IMX8QXP_UART1_TX_ADMA_UART1_TX 0X06000020 + >; + }; + + pinctrl_lpuart2: lpuart2grp { + fsl,pins = < + IMX8QXP_UART2_RX_ADMA_UART2_RX 0X06000020 + IMX8QXP_UART2_TX_ADMA_UART2_TX 0X06000020 + >; + }; + + pinctrl_lpuart3: lpuart3grp { + fsl,pins = < + IMX8QXP_FLEXCAN2_RX_ADMA_UART3_RX 0X06000020 + IMX8QXP_FLEXCAN2_TX_ADMA_UART3_TX 0X06000020 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + IMX8QXP_EMMC0_CLK_CONN_EMMC0_CLK 0x06000041 + IMX8QXP_EMMC0_CMD_CONN_EMMC0_CMD 0x00000021 + IMX8QXP_EMMC0_DATA0_CONN_EMMC0_DATA0 0x00000021 + IMX8QXP_EMMC0_DATA1_CONN_EMMC0_DATA1 0x00000021 + IMX8QXP_EMMC0_DATA2_CONN_EMMC0_DATA2 0x00000021 + IMX8QXP_EMMC0_DATA3_CONN_EMMC0_DATA3 0x00000021 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + IMX8QXP_USDHC1_CLK_CONN_USDHC1_CLK 0x06000041 + IMX8QXP_USDHC1_CMD_CONN_USDHC1_CMD 0x00000021 + IMX8QXP_USDHC1_DATA0_CONN_USDHC1_DATA0 0x00000021 + IMX8QXP_USDHC1_DATA1_CONN_USDHC1_DATA1 0x00000021 + IMX8QXP_USDHC1_DATA2_CONN_USDHC1_DATA2 0x00000021 + IMX8QXP_USDHC1_DATA3_CONN_USDHC1_DATA3 0x00000021 + IMX8QXP_USDHC1_VSELECT_CONN_USDHC1_VSELECT 0x00000021 + IMX8QXP_USDHC1_CD_B_LSIO_GPIO4_IO22 0x00000021 + >; + }; + + pinctrl_wifi_reg_on: wifiregongrp { + fsl,pins = < + IMX8QXP_QSPI0B_SS1_B_LSIO_GPIO3_IO24 0x00000021 + >; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8qxp.dtsi b/arch/arm64/boot/dts/freescale/imx8qxp.dtsi index b6c408fb2b7f..1133b412182a 100644 --- a/arch/arm64/boot/dts/freescale/imx8qxp.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8qxp.dtsi @@ -30,6 +30,9 @@ mmc2 = &usdhc3; mu1 = &lsio_mu1; serial0 = &adma_lpuart0; + serial1 = &adma_lpuart1; + serial2 = &adma_lpuart2; + serial3 = &adma_lpuart3; }; cpus { @@ -241,8 +244,9 @@ reg = <0x5a060000 0x1000>; interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>; interrupt-parent = <&gic>; - clocks = <&adma_lpcg IMX_ADMA_LPCG_UART0_BAUD_CLK>; - clock-names = "ipg"; + clocks = <&adma_lpcg IMX_ADMA_LPCG_UART0_IPG_CLK>, + <&adma_lpcg IMX_ADMA_LPCG_UART0_BAUD_CLK>; + clock-names = "ipg", "baud"; power-domains = <&pd IMX_SC_R_UART_0>; status = "disabled"; }; @@ -252,8 +256,9 @@ reg = <0x5a070000 0x1000>; interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>; interrupt-parent = <&gic>; - clocks = <&adma_lpcg IMX_ADMA_LPCG_UART1_BAUD_CLK>; - clock-names = "ipg"; + clocks = <&adma_lpcg IMX_ADMA_LPCG_UART1_IPG_CLK>, + <&adma_lpcg IMX_ADMA_LPCG_UART1_BAUD_CLK>; + clock-names = "ipg", "baud"; power-domains = <&pd IMX_SC_R_UART_1>; status = "disabled"; }; @@ -263,8 +268,9 @@ reg = <0x5a080000 0x1000>; interrupts = <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>; interrupt-parent = <&gic>; - clocks = <&adma_lpcg IMX_ADMA_LPCG_UART2_BAUD_CLK>; - clock-names = "ipg"; + clocks = <&adma_lpcg IMX_ADMA_LPCG_UART2_IPG_CLK>, + <&adma_lpcg IMX_ADMA_LPCG_UART2_BAUD_CLK>; + clock-names = "ipg", "baud"; power-domains = <&pd IMX_SC_R_UART_2>; status = "disabled"; }; @@ -274,8 +280,9 @@ reg = <0x5a090000 0x1000>; interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_HIGH>; interrupt-parent = <&gic>; - clocks = <&adma_lpcg IMX_ADMA_LPCG_UART3_BAUD_CLK>; - clock-names = "ipg"; + clocks = <&adma_lpcg IMX_ADMA_LPCG_UART3_IPG_CLK>, + <&adma_lpcg IMX_ADMA_LPCG_UART3_BAUD_CLK>; + clock-names = "ipg", "baud"; power-domains = <&pd IMX_SC_R_UART_3>; status = "disabled"; }; |