Merge tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull arm soc-specific pinctrl changes from Olof Johansson:
 "With this, five platforms are moving to the relatively new pinctrl
  subsystem for their pin management, replacing the older soc specific
  in-kernel interfaces with common code.

  There is quite a bit of net addition of code for each platform being
  added to the pinctrl subsystem.  But the payback comes later when
  adding new boards can be done by only providing new device trees
  instead."

Fix up trivial conflicts in arch/arm/mach-ux500/{Makefile,board-mop500.c}

* tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (61 commits)
  mtd: nand: gpmi: fix compile error caused by pinctrl call
  ARM: PRIMA2: select PINCTRL and PINCTRL_SIRF in Kconfig
  ARM: nomadik: enable PINCTRL_NOMADIK where needed
  ARM: mxs: enable pinctrl support
  video: mxsfb: adopt pinctrl support
  ASoC: mxs-saif: adopt pinctrl support
  i2c: mxs: adopt pinctrl support
  mtd: nand: gpmi: adopt pinctrl support
  mmc: mxs-mmc: adopt pinctrl support
  serial: mxs-auart: adopt pinctrl support
  serial: amba-pl011: adopt pinctrl support
  spi/imx: adopt pinctrl support
  i2c: imx: adopt pinctrl support
  can: flexcan: adopt pinctrl support
  net: fec: adopt pinctrl support
  ARM: ux500: switch MSP to using pinctrl for pins
  ARM: ux500: alter MSP registration to return a device pointer
  ARM: ux500: switch to using pinctrl for uart0
  ARM: ux500: delete custom pin control system
  ARM: ux500: switch over to Nomadik pinctrl driver
  ...

1 files changed, 1 insertions, 388 deletions

diff --git a/arch/arm/mach-spear3xx/spear300.c b/arch/arm/mach-spear3xx/spear300.c
index febcdd8d4e92..f75fe25a620c 100644
--- a/arch/arm/mach-spear3xx/spear300.c
+++ b/arch/arm/mach-spear3xx/spear300.c
@@ -60,357 +60,6 @@
 /* IRQs sharing IRQ_INTRCOMM_RAS_ARM */
 #define SPEAR300_IRQ_SDHCI			SPEAR3XX_IRQ_INTRCOMM_RAS_ARM
 
-/* pad multiplexing support */
-/* muxing registers */
-#define PAD_MUX_CONFIG_REG	0x00
-#define MODE_CONFIG_REG		0x04
-
-/* modes */
-#define NAND_MODE			(1 << 0)
-#define NOR_MODE			(1 << 1)
-#define PHOTO_FRAME_MODE		(1 << 2)
-#define LEND_IP_PHONE_MODE		(1 << 3)
-#define HEND_IP_PHONE_MODE		(1 << 4)
-#define LEND_WIFI_PHONE_MODE		(1 << 5)
-#define HEND_WIFI_PHONE_MODE		(1 << 6)
-#define ATA_PABX_WI2S_MODE		(1 << 7)
-#define ATA_PABX_I2S_MODE		(1 << 8)
-#define CAML_LCDW_MODE			(1 << 9)
-#define CAMU_LCD_MODE			(1 << 10)
-#define CAMU_WLCD_MODE			(1 << 11)
-#define CAML_LCD_MODE			(1 << 12)
-#define ALL_MODES			0x1FFF
-
-struct pmx_mode spear300_nand_mode = {
-	.id = NAND_MODE,
-	.name = "nand mode",
-	.mask = 0x00,
-};
-
-struct pmx_mode spear300_nor_mode = {
-	.id = NOR_MODE,
-	.name = "nor mode",
-	.mask = 0x01,
-};
-
-struct pmx_mode spear300_photo_frame_mode = {
-	.id = PHOTO_FRAME_MODE,
-	.name = "photo frame mode",
-	.mask = 0x02,
-};
-
-struct pmx_mode spear300_lend_ip_phone_mode = {
-	.id = LEND_IP_PHONE_MODE,
-	.name = "lend ip phone mode",
-	.mask = 0x03,
-};
-
-struct pmx_mode spear300_hend_ip_phone_mode = {
-	.id = HEND_IP_PHONE_MODE,
-	.name = "hend ip phone mode",
-	.mask = 0x04,
-};
-
-struct pmx_mode spear300_lend_wifi_phone_mode = {
-	.id = LEND_WIFI_PHONE_MODE,
-	.name = "lend wifi phone mode",
-	.mask = 0x05,
-};
-
-struct pmx_mode spear300_hend_wifi_phone_mode = {
-	.id = HEND_WIFI_PHONE_MODE,
-	.name = "hend wifi phone mode",
-	.mask = 0x06,
-};
-
-struct pmx_mode spear300_ata_pabx_wi2s_mode = {
-	.id = ATA_PABX_WI2S_MODE,
-	.name = "ata pabx wi2s mode",
-	.mask = 0x07,
-};
-
-struct pmx_mode spear300_ata_pabx_i2s_mode = {
-	.id = ATA_PABX_I2S_MODE,
-	.name = "ata pabx i2s mode",
-	.mask = 0x08,
-};
-
-struct pmx_mode spear300_caml_lcdw_mode = {
-	.id = CAML_LCDW_MODE,
-	.name = "caml lcdw mode",
-	.mask = 0x0C,
-};
-
-struct pmx_mode spear300_camu_lcd_mode = {
-	.id = CAMU_LCD_MODE,
-	.name = "camu lcd mode",
-	.mask = 0x0D,
-};
-
-struct pmx_mode spear300_camu_wlcd_mode = {
-	.id = CAMU_WLCD_MODE,
-	.name = "camu wlcd mode",
-	.mask = 0x0E,
-};
-
-struct pmx_mode spear300_caml_lcd_mode = {
-	.id = CAML_LCD_MODE,
-	.name = "caml lcd mode",
-	.mask = 0x0F,
-};
-
-/* devices */
-static struct pmx_dev_mode pmx_fsmc_2_chips_modes[] = {
-	{
-		.ids = NAND_MODE | NOR_MODE | PHOTO_FRAME_MODE |
-			ATA_PABX_WI2S_MODE | ATA_PABX_I2S_MODE,
-		.mask = PMX_FIRDA_MASK,
-	},
-};
-
-struct pmx_dev spear300_pmx_fsmc_2_chips = {
-	.name = "fsmc_2_chips",
-	.modes = pmx_fsmc_2_chips_modes,
-	.mode_count = ARRAY_SIZE(pmx_fsmc_2_chips_modes),
-	.enb_on_reset = 1,
-};
-
-static struct pmx_dev_mode pmx_fsmc_4_chips_modes[] = {
-	{
-		.ids = NAND_MODE | NOR_MODE | PHOTO_FRAME_MODE |
-			ATA_PABX_WI2S_MODE | ATA_PABX_I2S_MODE,
-		.mask = PMX_FIRDA_MASK | PMX_UART0_MASK,
-	},
-};
-
-struct pmx_dev spear300_pmx_fsmc_4_chips = {
-	.name = "fsmc_4_chips",
-	.modes = pmx_fsmc_4_chips_modes,
-	.mode_count = ARRAY_SIZE(pmx_fsmc_4_chips_modes),
-	.enb_on_reset = 1,
-};
-
-static struct pmx_dev_mode pmx_keyboard_modes[] = {
-	{
-		.ids = LEND_IP_PHONE_MODE | HEND_IP_PHONE_MODE |
-			LEND_WIFI_PHONE_MODE | HEND_WIFI_PHONE_MODE |
-			CAML_LCDW_MODE | CAMU_LCD_MODE | CAMU_WLCD_MODE |
-			CAML_LCD_MODE,
-		.mask = 0x0,
-	},
-};
-
-struct pmx_dev spear300_pmx_keyboard = {
-	.name = "keyboard",
-	.modes = pmx_keyboard_modes,
-	.mode_count = ARRAY_SIZE(pmx_keyboard_modes),
-	.enb_on_reset = 1,
-};
-
-static struct pmx_dev_mode pmx_clcd_modes[] = {
-	{
-		.ids = PHOTO_FRAME_MODE,
-		.mask = PMX_TIMER_1_2_MASK | PMX_TIMER_3_4_MASK ,
-	}, {
-		.ids = HEND_IP_PHONE_MODE | HEND_WIFI_PHONE_MODE |
-			CAMU_LCD_MODE | CAML_LCD_MODE,
-		.mask = PMX_TIMER_3_4_MASK,
-	},
-};
-
-struct pmx_dev spear300_pmx_clcd = {
-	.name = "clcd",
-	.modes = pmx_clcd_modes,
-	.mode_count = ARRAY_SIZE(pmx_clcd_modes),
-	.enb_on_reset = 1,
-};
-
-static struct pmx_dev_mode pmx_telecom_gpio_modes[] = {
-	{
-		.ids = PHOTO_FRAME_MODE | CAMU_LCD_MODE | CAML_LCD_MODE,
-		.mask = PMX_MII_MASK,
-	}, {
-		.ids = LEND_IP_PHONE_MODE | LEND_WIFI_PHONE_MODE,
-		.mask = PMX_MII_MASK | PMX_TIMER_1_2_MASK | PMX_TIMER_3_4_MASK,
-	}, {
-		.ids = ATA_PABX_I2S_MODE | CAML_LCDW_MODE | CAMU_WLCD_MODE,
-		.mask = PMX_MII_MASK | PMX_TIMER_3_4_MASK,
-	}, {
-		.ids = HEND_IP_PHONE_MODE | HEND_WIFI_PHONE_MODE,
-		.mask = PMX_MII_MASK | PMX_TIMER_1_2_MASK,
-	}, {
-		.ids = ATA_PABX_WI2S_MODE,
-		.mask = PMX_MII_MASK | PMX_TIMER_1_2_MASK | PMX_TIMER_3_4_MASK
-			| PMX_UART0_MODEM_MASK,
-	},
-};
-
-struct pmx_dev spear300_pmx_telecom_gpio = {
-	.name = "telecom_gpio",
-	.modes = pmx_telecom_gpio_modes,
-	.mode_count = ARRAY_SIZE(pmx_telecom_gpio_modes),
-	.enb_on_reset = 1,
-};
-
-static struct pmx_dev_mode pmx_telecom_tdm_modes[] = {
-	{
-		.ids = PHOTO_FRAME_MODE | LEND_IP_PHONE_MODE |
-			HEND_IP_PHONE_MODE | LEND_WIFI_PHONE_MODE
-			| HEND_WIFI_PHONE_MODE | ATA_PABX_WI2S_MODE
-			| ATA_PABX_I2S_MODE | CAML_LCDW_MODE | CAMU_LCD_MODE
-			| CAMU_WLCD_MODE | CAML_LCD_MODE,
-		.mask = PMX_UART0_MODEM_MASK | PMX_SSP_CS_MASK,
-	},
-};
-
-struct pmx_dev spear300_pmx_telecom_tdm = {
-	.name = "telecom_tdm",
-	.modes = pmx_telecom_tdm_modes,
-	.mode_count = ARRAY_SIZE(pmx_telecom_tdm_modes),
-	.enb_on_reset = 1,
-};
-
-static struct pmx_dev_mode pmx_telecom_spi_cs_i2c_clk_modes[] = {
-	{
-		.ids = LEND_IP_PHONE_MODE | HEND_IP_PHONE_MODE |
-			LEND_WIFI_PHONE_MODE | HEND_WIFI_PHONE_MODE
-			| ATA_PABX_WI2S_MODE | ATA_PABX_I2S_MODE |
-			CAML_LCDW_MODE | CAML_LCD_MODE,
-		.mask = PMX_TIMER_1_2_MASK | PMX_TIMER_3_4_MASK,
-	},
-};
-
-struct pmx_dev spear300_pmx_telecom_spi_cs_i2c_clk = {
-	.name = "telecom_spi_cs_i2c_clk",
-	.modes = pmx_telecom_spi_cs_i2c_clk_modes,
-	.mode_count = ARRAY_SIZE(pmx_telecom_spi_cs_i2c_clk_modes),
-	.enb_on_reset = 1,
-};
-
-static struct pmx_dev_mode pmx_telecom_camera_modes[] = {
-	{
-		.ids = CAML_LCDW_MODE | CAML_LCD_MODE,
-		.mask = PMX_MII_MASK,
-	}, {
-		.ids = CAMU_LCD_MODE | CAMU_WLCD_MODE,
-		.mask = PMX_TIMER_1_2_MASK | PMX_TIMER_3_4_MASK | PMX_MII_MASK,
-	},
-};
-
-struct pmx_dev spear300_pmx_telecom_camera = {
-	.name = "telecom_camera",
-	.modes = pmx_telecom_camera_modes,
-	.mode_count = ARRAY_SIZE(pmx_telecom_camera_modes),
-	.enb_on_reset = 1,
-};
-
-static struct pmx_dev_mode pmx_telecom_dac_modes[] = {
-	{
-		.ids = ATA_PABX_I2S_MODE | CAML_LCDW_MODE | CAMU_LCD_MODE
-			| CAMU_WLCD_MODE | CAML_LCD_MODE,
-		.mask = PMX_TIMER_1_2_MASK,
-	},
-};
-
-struct pmx_dev spear300_pmx_telecom_dac = {
-	.name = "telecom_dac",
-	.modes = pmx_telecom_dac_modes,
-	.mode_count = ARRAY_SIZE(pmx_telecom_dac_modes),
-	.enb_on_reset = 1,
-};
-
-static struct pmx_dev_mode pmx_telecom_i2s_modes[] = {
-	{
-		.ids = LEND_IP_PHONE_MODE | HEND_IP_PHONE_MODE
-			| LEND_WIFI_PHONE_MODE | HEND_WIFI_PHONE_MODE |
-			ATA_PABX_I2S_MODE | CAML_LCDW_MODE | CAMU_LCD_MODE
-			| CAMU_WLCD_MODE | CAML_LCD_MODE,
-		.mask = PMX_UART0_MODEM_MASK,
-	},
-};
-
-struct pmx_dev spear300_pmx_telecom_i2s = {
-	.name = "telecom_i2s",
-	.modes = pmx_telecom_i2s_modes,
-	.mode_count = ARRAY_SIZE(pmx_telecom_i2s_modes),
-	.enb_on_reset = 1,
-};
-
-static struct pmx_dev_mode pmx_telecom_boot_pins_modes[] = {
-	{
-		.ids = NAND_MODE | NOR_MODE,
-		.mask = PMX_UART0_MODEM_MASK | PMX_TIMER_1_2_MASK |
-			PMX_TIMER_3_4_MASK,
-	},
-};
-
-struct pmx_dev spear300_pmx_telecom_boot_pins = {
-	.name = "telecom_boot_pins",
-	.modes = pmx_telecom_boot_pins_modes,
-	.mode_count = ARRAY_SIZE(pmx_telecom_boot_pins_modes),
-	.enb_on_reset = 1,
-};
-
-static struct pmx_dev_mode pmx_telecom_sdhci_4bit_modes[] = {
-	{
-		.ids = PHOTO_FRAME_MODE | LEND_IP_PHONE_MODE |
-			HEND_IP_PHONE_MODE | LEND_WIFI_PHONE_MODE |
-			HEND_WIFI_PHONE_MODE | CAML_LCDW_MODE | CAMU_LCD_MODE |
-			CAMU_WLCD_MODE | CAML_LCD_MODE | ATA_PABX_WI2S_MODE |
-			ATA_PABX_I2S_MODE,
-		.mask = PMX_GPIO_PIN0_MASK | PMX_GPIO_PIN1_MASK |
-			PMX_GPIO_PIN2_MASK | PMX_GPIO_PIN3_MASK |
-			PMX_GPIO_PIN4_MASK | PMX_GPIO_PIN5_MASK,
-	},
-};
-
-struct pmx_dev spear300_pmx_telecom_sdhci_4bit = {
-	.name = "telecom_sdhci_4bit",
-	.modes = pmx_telecom_sdhci_4bit_modes,
-	.mode_count = ARRAY_SIZE(pmx_telecom_sdhci_4bit_modes),
-	.enb_on_reset = 1,
-};
-
-static struct pmx_dev_mode pmx_telecom_sdhci_8bit_modes[] = {
-	{
-		.ids = PHOTO_FRAME_MODE | LEND_IP_PHONE_MODE |
-			HEND_IP_PHONE_MODE | LEND_WIFI_PHONE_MODE |
-			HEND_WIFI_PHONE_MODE | CAML_LCDW_MODE | CAMU_LCD_MODE |
-			CAMU_WLCD_MODE | CAML_LCD_MODE,
-		.mask = PMX_GPIO_PIN0_MASK | PMX_GPIO_PIN1_MASK |
-			PMX_GPIO_PIN2_MASK | PMX_GPIO_PIN3_MASK |
-			PMX_GPIO_PIN4_MASK | PMX_GPIO_PIN5_MASK | PMX_MII_MASK,
-	},
-};
-
-struct pmx_dev spear300_pmx_telecom_sdhci_8bit = {
-	.name = "telecom_sdhci_8bit",
-	.modes = pmx_telecom_sdhci_8bit_modes,
-	.mode_count = ARRAY_SIZE(pmx_telecom_sdhci_8bit_modes),
-	.enb_on_reset = 1,
-};
-
-static struct pmx_dev_mode pmx_gpio1_modes[] = {
-	{
-		.ids = PHOTO_FRAME_MODE,
-		.mask = PMX_UART0_MODEM_MASK | PMX_TIMER_1_2_MASK |
-			PMX_TIMER_3_4_MASK,
-	},
-};
-
-struct pmx_dev spear300_pmx_gpio1 = {
-	.name = "arm gpio1",
-	.modes = pmx_gpio1_modes,
-	.mode_count = ARRAY_SIZE(pmx_gpio1_modes),
-	.enb_on_reset = 1,
-};
-
-/* pmx driver structure */
-static struct pmx_driver pmx_driver = {
-	.mode_reg = {.offset = MODE_CONFIG_REG, .mask = 0x0000000f},
-	.mux_reg = {.offset = PAD_MUX_CONFIG_REG, .mask = 0x00007fff},
-};
-
 /* spear3xx shared irq */
 static struct shirq_dev_config shirq_ras1_config[] = {
 	{
@@ -464,22 +113,6 @@ static struct spear_shirq shirq_ras1 = {
 	},
 };
 
-/* padmux devices to enable */
-static struct pmx_dev *spear300_evb_pmx_devs[] = {
-	/* spear3xx specific devices */
-	&spear3xx_pmx_i2c,
-	&spear3xx_pmx_ssp_cs,
-	&spear3xx_pmx_ssp,
-	&spear3xx_pmx_mii,
-	&spear3xx_pmx_uart0,
-
-	/* spear300 specific devices */
-	&spear300_pmx_fsmc_2_chips,
-	&spear300_pmx_clcd,
-	&spear300_pmx_telecom_sdhci_4bit,
-	&spear300_pmx_gpio1,
-};
-
 /* DMAC platform data's slave info */
 struct pl08x_channel_data spear300_dma_info[] = {
 	{
@@ -678,7 +311,7 @@ static struct of_dev_auxdata spear300_auxdata_lookup[] __initdata = {
 
 static void __init spear300_dt_init(void)
 {
-	int ret = -EINVAL;
+	int ret;
 
 	pl080_plat_data.slave_channels = spear300_dma_info;
 	pl080_plat_data.num_slave_channels = ARRAY_SIZE(spear300_dma_info);
@@ -693,26 +326,6 @@ static void __init spear300_dt_init(void)
 		if (ret)
 			pr_err("Error registering Shared IRQ\n");
 	}
-
-	if (of_machine_is_compatible("st,spear300-evb")) {
-		/* pmx initialization */
-		pmx_driver.mode = &spear300_photo_frame_mode;
-		pmx_driver.devs = spear300_evb_pmx_devs;
-		pmx_driver.devs_count = ARRAY_SIZE(spear300_evb_pmx_devs);
-
-		pmx_driver.base = ioremap(SPEAR300_SOC_CONFIG_BASE, SZ_4K);
-		if (pmx_driver.base) {
-			ret = pmx_register(&pmx_driver);
-			if (ret)
-				pr_err("padmux: registration failed. err no: %d\n",
-						ret);
-			/* Free Mapping, device selection already done */
-			iounmap(pmx_driver.base);
-		}
-
-		if (ret)
-			pr_err("Initialization Failed");
-	}
 }
 
 static const char * const spear300_dt_board_compat[] = {