Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC platform updates from Arnd Bergmann:
 "The main change this time around is a cleanup of some of the oldest
  platforms based on the XScale and ARM9 CPU cores, which are between 10
  and 20 years old.

  The Kendin/Micrel/Microchip KS8695, Winbond/Nuvoton W90x900 and Intel
  IOP33x/IOP13xx platforms are removed after we determined that nobody
  is using them any more.

  The TI Davinci and NXP LPC32xx platforms on the other hand are still
  in active use and are converted to the ARCH_MULTIPLATFORM build,
  meaning that we can compile a kernel that works on these along with
  most other ARMv5 platforms. Changes toward that goal are also merged
  for IOP32x, but additional work is needed to complete this. Patches
  for the remaining ARMv5 platforms have started but need more work and
  some testing.

  Support for the new ASpeed AST2600 gets added, this is based on the
  Cortex-A7 ARMv7 core, and is a newer version of the existing ARMv5 and
  ARMv6 chips in the same family.

  Other changes include a cleanup of the ST-Ericsson ux500 platform and
  the move of the TI Davinci platform to a new clocksource driver"

[ The changes had marked INTEL_IOP_ADMA and USB_LPC32XX as being
  buildable on other platforms through COMPILE_TEST, but that causes new
  warnings that I most definitely do not want to see during the merge
  window as that could hide other issues.

  So the COMPILE_TEST option got disabled for them again   - Linus ]

* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (61 commits)
  ARM: multi_v5_defconfig: make DaVinci part of the ARM v5 multiplatform build
  ARM: davinci: support multiplatform build for ARM v5
  arm64: exynos: Enable exynos-chipid driver
  ARM: OMAP2+: Delete an unnecessary kfree() call in omap_hsmmc_pdata_init()
  ARM: OMAP2+: move platform-specific asm-offset.h to arch/arm/mach-omap2
  ARM: davinci: dm646x: Fix a typo in the comment
  ARM: davinci: dm646x: switch to using the clocksource driver
  ARM: davinci: dm644x: switch to using the clocksource driver
  ARM: aspeed: Enable SMP boot
  ARM: aspeed: Add ASPEED AST2600 architecture
  ARM: aspeed: Select timer in each SoC
  dt-bindings: arm: cpus: Add ASPEED SMP
  ARM: imx: stop adjusting ar8031 phy tx delay
  mailmap: map old company name to new one @microchip.com
  MAINTAINERS: at91: remove the TC entry
  MAINTAINERS: at91: Collect all pinctrl/gpio drivers in same entry
  ARM: at91: move platform-specific asm-offset.h to arch/arm/mach-at91
  MAINTAINERS: Extend patterns for Samsung SoC, Security Subsystem and clock drivers
  ARM: s3c64xx: squash samsung_usb_phy.h into setup-usb-phy.c
  ARM: debug-ll: Add support for r7s9210
  ...

1 files changed, 0 insertions, 1115 deletions

diff --git a/arch/arm/mach-iop13xx/pci.c b/arch/arm/mach-iop13xx/pci.c
deleted file mode 100644
index 46ea06e906cc..000000000000
--- a/arch/arm/mach-iop13xx/pci.c
+++ /dev/null
@@ -1,1115 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * iop13xx PCI support
- * Copyright (c) 2005-2006, Intel Corporation.
- */
-
-#include <linux/pci.h>
-#include <linux/slab.h>
-#include <linux/delay.h>
-#include <linux/jiffies.h>
-#include <linux/export.h>
-#include <asm/irq.h>
-#include <mach/hardware.h>
-#include <linux/sizes.h>
-#include <asm/signal.h>
-#include <asm/mach/pci.h>
-#include "pci.h"
-
-#define IOP13XX_PCI_DEBUG 0
-#define PRINTK(x...) ((void)(IOP13XX_PCI_DEBUG && printk(x)))
-
-u32 iop13xx_atux_pmmr_offset; /* This offset can change based on strapping */
-u32 iop13xx_atue_pmmr_offset; /* This offset can change based on strapping */
-static struct pci_bus *pci_bus_atux = 0;
-static struct pci_bus *pci_bus_atue = 0;
-void __iomem *iop13xx_atue_mem_base;
-void __iomem *iop13xx_atux_mem_base;
-size_t iop13xx_atue_mem_size;
-size_t iop13xx_atux_mem_size;
-
-EXPORT_SYMBOL(iop13xx_atue_mem_base);
-EXPORT_SYMBOL(iop13xx_atux_mem_base);
-EXPORT_SYMBOL(iop13xx_atue_mem_size);
-EXPORT_SYMBOL(iop13xx_atux_mem_size);
-
-int init_atu = 0; /* Flag to select which ATU(s) to initialize / disable */
-static unsigned long atux_trhfa_timeout = 0; /* Trhfa = RST# high to first
-						 access */
-
-/* Scan the initialized busses and ioremap the requested memory range
- */
-void iop13xx_map_pci_memory(void)
-{
-	int atu;
-	struct pci_bus *bus;
-	struct pci_dev *dev;
-	resource_size_t end = 0;
-
-	for (atu = 0; atu < 2; atu++) {
-		bus = atu ? pci_bus_atue : pci_bus_atux;
-		if (bus) {
-			list_for_each_entry(dev, &bus->devices, bus_list) {
-				int i;
-				int max = 7;
-
-				if (dev->subordinate)
-					max = DEVICE_COUNT_RESOURCE;
-
-				for (i = 0; i < max; i++) {
-					struct resource *res = &dev->resource[i];
-					if (res->flags & IORESOURCE_MEM)
-						end = max(res->end, end);
-				}
-			}
-
-			switch(atu) {
-			case 0:
-				iop13xx_atux_mem_size =
-					(end - IOP13XX_PCIX_LOWER_MEM_RA) + 1;
-
-				/* 16MB align the request */
-				if (iop13xx_atux_mem_size & (SZ_16M - 1)) {
-					iop13xx_atux_mem_size &= ~(SZ_16M - 1);
-					iop13xx_atux_mem_size += SZ_16M;
-				}
-
-				if (end) {
-					iop13xx_atux_mem_base = __arm_ioremap_pfn(
-					__phys_to_pfn(IOP13XX_PCIX_LOWER_MEM_PA)
-					, 0, iop13xx_atux_mem_size, MT_DEVICE);
-					if (!iop13xx_atux_mem_base) {
-						printk("%s: atux allocation "
-						       "failed\n", __func__);
-						BUG();
-					}
-				} else
-					iop13xx_atux_mem_size = 0;
-				PRINTK("%s: atu: %d bus_size: %d mem_base: %p\n",
-				__func__, atu, iop13xx_atux_mem_size,
-				iop13xx_atux_mem_base);
-				break;
-			case 1:
-				iop13xx_atue_mem_size =
-					(end - IOP13XX_PCIE_LOWER_MEM_RA) + 1;
-
-				/* 16MB align the request */
-				if (iop13xx_atue_mem_size & (SZ_16M - 1)) {
-					iop13xx_atue_mem_size &= ~(SZ_16M - 1);
-					iop13xx_atue_mem_size += SZ_16M;
-				}
-
-				if (end) {
-					iop13xx_atue_mem_base = __arm_ioremap_pfn(
-					__phys_to_pfn(IOP13XX_PCIE_LOWER_MEM_PA)
-					, 0, iop13xx_atue_mem_size, MT_DEVICE);
-					if (!iop13xx_atue_mem_base) {
-						printk("%s: atue allocation "
-						       "failed\n", __func__);
-						BUG();
-					}
-				} else
-					iop13xx_atue_mem_size = 0;
-				PRINTK("%s: atu: %d bus_size: %d mem_base: %p\n",
-				__func__, atu, iop13xx_atue_mem_size,
-				iop13xx_atue_mem_base);
-				break;
-			}
-
-			printk("%s: Initialized (%uM @ resource/virtual: %08lx/%p)\n",
-			atu ? "ATUE" : "ATUX",
-			(atu ? iop13xx_atue_mem_size : iop13xx_atux_mem_size) /
-			SZ_1M,
-			atu ? IOP13XX_PCIE_LOWER_MEM_RA :
-			IOP13XX_PCIX_LOWER_MEM_RA,
-			atu ? iop13xx_atue_mem_base :
-			iop13xx_atux_mem_base);
-			end = 0;
-		}
-
-	}
-}
-
-static int iop13xx_atu_function(int atu)
-{
-	int func = 0;
-	/* the function number depends on the value of the
-	 * IOP13XX_INTERFACE_SEL_PCIX reset strap
-	 * see C-Spec section 3.17
-	 */
-	switch(atu) {
-	case IOP13XX_INIT_ATU_ATUX:
-		if (__raw_readl(IOP13XX_ESSR0) & IOP13XX_INTERFACE_SEL_PCIX)
-			func = 5;
-		else
-			func = 0;
-		break;
-	case IOP13XX_INIT_ATU_ATUE:
-		if (__raw_readl(IOP13XX_ESSR0) & IOP13XX_INTERFACE_SEL_PCIX)
-			func = 0;
-		else
-			func = 5;
-		break;
-	default:
-		BUG();
-	}
-
-	return func;
-}
-
-/* iop13xx_atux_cfg_address - format a configuration address for atux
- * @bus: Target bus to access
- * @devfn: Combined device number and function number
- * @where: Desired register's address offset
- *
- * Convert the parameters to a configuration address formatted
- * according the PCI-X 2.0 specification
- */
-static u32 iop13xx_atux_cfg_address(struct pci_bus *bus, int devfn, int where)
-{
-	struct pci_sys_data *sys = bus->sysdata;
-	u32 addr;
-
-	if (sys->busnr == bus->number)
-		addr = 1 << (PCI_SLOT(devfn) + 16) | (PCI_SLOT(devfn) << 11);
-	else
-		addr = bus->number << 16 | PCI_SLOT(devfn) << 11 | 1;
-
-	addr |=	PCI_FUNC(devfn) << 8 | ((where & 0xff) & ~3);
-	addr |= ((where & 0xf00) >> 8) << 24; /* upper register number */
-
-	return addr;
-}
-
-/* iop13xx_atue_cfg_address - format a configuration address for atue
- * @bus: Target bus to access
- * @devfn: Combined device number and function number
- * @where: Desired register's address offset
- *
- * Convert the parameters to an address usable by the ATUE_OCCAR
- */
-static u32 iop13xx_atue_cfg_address(struct pci_bus *bus, int devfn, int where)
-{
-	struct pci_sys_data *sys = bus->sysdata;
-	u32 addr;
-
-	PRINTK("iop13xx_atue_cfg_address: bus: %d dev: %d func: %d",
-		bus->number, PCI_SLOT(devfn), PCI_FUNC(devfn));
-	addr = ((u32) bus->number)     << IOP13XX_ATUE_OCCAR_BUS_NUM |
-		   ((u32) PCI_SLOT(devfn)) << IOP13XX_ATUE_OCCAR_DEV_NUM |
-		   ((u32) PCI_FUNC(devfn)) << IOP13XX_ATUE_OCCAR_FUNC_NUM |
-		   (where & ~0x3);
-
-	if (sys->busnr != bus->number)
-		addr |= 1; /* type 1 access */
-
-	return addr;
-}
-
-/* This routine checks the status of the last configuration cycle.  If an error
- * was detected it returns >0, else it returns a 0.  The errors being checked
- * are parity, master abort, target abort (master and target).  These types of
- * errors occur during a config cycle where there is no device, like during
- * the discovery stage.
- */
-static int iop13xx_atux_pci_status(int clear)
-{
-	unsigned int status;
-	int err = 0;
-
-	/*
-	 * Check the status registers.
-	 */
-	status = __raw_readw(IOP13XX_ATUX_ATUSR);
-	if (status & IOP_PCI_STATUS_ERROR)
-	{
-		PRINTK("\t\t\tPCI error: ATUSR %#08x", status);
-		if(clear)
-			__raw_writew(status & IOP_PCI_STATUS_ERROR,
-				IOP13XX_ATUX_ATUSR);
-		err = 1;
-	}
-	status = __raw_readl(IOP13XX_ATUX_ATUISR);
-	if (status & IOP13XX_ATUX_ATUISR_ERROR)
-	{
-		PRINTK("\t\t\tPCI error interrupt:  ATUISR %#08x", status);
-		if(clear)
-			__raw_writel(status & IOP13XX_ATUX_ATUISR_ERROR,
-				IOP13XX_ATUX_ATUISR);
-		err = 1;
-	}
-	return err;
-}
-
-/* Simply write the address register and read the configuration
- * data.  Note that the data dependency on %0 encourages an abort
- * to be detected before we return.
- */
-static u32 iop13xx_atux_read(unsigned long addr)
-{
-	u32 val;
-
-	__asm__ __volatile__(
-		"str	%1, [%2]\n\t"
-		"ldr	%0, [%3]\n\t"
-		"mov	%0, %0\n\t"
-		: "=r" (val)
-		: "r" (addr), "r" (IOP13XX_ATUX_OCCAR), "r" (IOP13XX_ATUX_OCCDR));
-
-	return val;
-}
-
-/* The read routines must check the error status of the last configuration
- * cycle.  If there was an error, the routine returns all hex f's.
- */
-static int
-iop13xx_atux_read_config(struct pci_bus *bus, unsigned int devfn, int where,
-		int size, u32 *value)
-{
-	unsigned long addr = iop13xx_atux_cfg_address(bus, devfn, where);
-	u32 val = iop13xx_atux_read(addr) >> ((where & 3) * 8);
-
-	if (iop13xx_atux_pci_status(1) || is_atux_occdr_error()) {
-		__raw_writel(__raw_readl(IOP13XX_XBG_BECSR) & 3,
-			IOP13XX_XBG_BECSR);
-		val = 0xffffffff;
-	}
-
-	*value = val;
-
-	return PCIBIOS_SUCCESSFUL;
-}
-
-static int
-iop13xx_atux_write_config(struct pci_bus *bus, unsigned int devfn, int where,
-		int size, u32 value)
-{
-	unsigned long addr = iop13xx_atux_cfg_address(bus, devfn, where);
-	u32 val;
-
-	if (size != 4) {
-		val = iop13xx_atux_read(addr);
-		if (!iop13xx_atux_pci_status(1) == 0)
-			return PCIBIOS_SUCCESSFUL;
-
-		where = (where & 3) * 8;
-
-		if (size == 1)
-			val &= ~(0xff << where);
-		else
-			val &= ~(0xffff << where);
-
-		__raw_writel(val | value << where, IOP13XX_ATUX_OCCDR);
-	} else {
-		__raw_writel(addr, IOP13XX_ATUX_OCCAR);
-		__raw_writel(value, IOP13XX_ATUX_OCCDR);
-	}
-
-	return PCIBIOS_SUCCESSFUL;
-}
-
-static struct pci_ops iop13xx_atux_ops = {
-	.read	= iop13xx_atux_read_config,
-	.write	= iop13xx_atux_write_config,
-};
-
-/* This routine checks the status of the last configuration cycle.  If an error
- * was detected it returns >0, else it returns a 0.  The errors being checked
- * are parity, master abort, target abort (master and target).  These types of
- * errors occur during a config cycle where there is no device, like during
- * the discovery stage.
- */
-static int iop13xx_atue_pci_status(int clear)
-{
-	unsigned int status;
-	int err = 0;
-
-	/*
-	 * Check the status registers.
-	 */
-
-	/* standard pci status register */
-	status = __raw_readw(IOP13XX_ATUE_ATUSR);
-	if (status & IOP_PCI_STATUS_ERROR) {
-		PRINTK("\t\t\tPCI error: ATUSR %#08x", status);
-		if(clear)
-			__raw_writew(status & IOP_PCI_STATUS_ERROR,
-				IOP13XX_ATUE_ATUSR);
-		err++;
-	}
-
-	/* check the normal status bits in the ATUISR */
-	status = __raw_readl(IOP13XX_ATUE_ATUISR);
-	if (status & IOP13XX_ATUE_ATUISR_ERROR)	{
-		PRINTK("\t\t\tPCI error: ATUISR %#08x", status);
-		if (clear)
-			__raw_writew(status & IOP13XX_ATUE_ATUISR_ERROR,
-				IOP13XX_ATUE_ATUISR);
-		err++;
-
-		/* check the PCI-E status if the ATUISR reports an interface error */
-		if (status & IOP13XX_ATUE_STAT_PCI_IFACE_ERR) {
-			/* get the unmasked errors */
-			status = __raw_readl(IOP13XX_ATUE_PIE_STS) &
-					~(__raw_readl(IOP13XX_ATUE_PIE_MSK));
-
-			if (status) {
-				PRINTK("\t\t\tPCI-E error: ATUE_PIE_STS %#08x",
-					__raw_readl(IOP13XX_ATUE_PIE_STS));
-				err++;
-			} else {
-				PRINTK("\t\t\tPCI-E error: ATUE_PIE_STS %#08x",
-					__raw_readl(IOP13XX_ATUE_PIE_STS));
-				PRINTK("\t\t\tPCI-E error: ATUE_PIE_MSK %#08x",
-					__raw_readl(IOP13XX_ATUE_PIE_MSK));
-				BUG();
-			}
-
-			if(clear)
-				__raw_writel(status, IOP13XX_ATUE_PIE_STS);
-		}
-	}
-
-	return err;
-}
-
-static int
-iop13xx_pcie_map_irq(const struct pci_dev *dev, u8 idsel, u8 pin)
-{
-	WARN_ON(idsel != 0);
-
-	switch (pin) {
-	case 1: return ATUE_INTA;
-	case 2: return ATUE_INTB;
-	case 3: return ATUE_INTC;
-	case 4: return ATUE_INTD;
-	default: return -1;
-	}
-}
-
-static u32 iop13xx_atue_read(unsigned long addr)
-{
-	u32 val;
-
-	__raw_writel(addr, IOP13XX_ATUE_OCCAR);
-	val = __raw_readl(IOP13XX_ATUE_OCCDR);
-
-	rmb();
-
-	return val;
-}
-
-/* The read routines must check the error status of the last configuration
- * cycle.  If there was an error, the routine returns all hex f's.
- */
-static int
-iop13xx_atue_read_config(struct pci_bus *bus, unsigned int devfn, int where,
-		int size, u32 *value)
-{
-	u32 val;
-	unsigned long addr = iop13xx_atue_cfg_address(bus, devfn, where);
-
-	/* Hide device numbers > 0 on the local PCI-E bus (Type 0 access) */
-	if (!PCI_SLOT(devfn) || (addr & 1)) {
-		val = iop13xx_atue_read(addr) >> ((where & 3) * 8);
-		if( iop13xx_atue_pci_status(1) || is_atue_occdr_error() ) {
-			__raw_writel(__raw_readl(IOP13XX_XBG_BECSR) & 3,
-				IOP13XX_XBG_BECSR);
-			val = 0xffffffff;
-		}
-
-		PRINTK("addr=%#0lx, val=%#010x", addr, val);
-	} else
-		val = 0xffffffff;
-
-	*value = val;
-
-	return PCIBIOS_SUCCESSFUL;
-}
-
-static int
-iop13xx_atue_write_config(struct pci_bus *bus, unsigned int devfn, int where,
-		int size, u32 value)
-{
-	unsigned long addr = iop13xx_atue_cfg_address(bus, devfn, where);
-	u32 val;
-
-	if (size != 4) {
-		val = iop13xx_atue_read(addr);
-		if (!iop13xx_atue_pci_status(1) == 0)
-			return PCIBIOS_SUCCESSFUL;
-
-		where = (where & 3) * 8;
-
-		if (size == 1)
-			val &= ~(0xff << where);
-		else
-			val &= ~(0xffff << where);
-
-		__raw_writel(val | value << where, IOP13XX_ATUE_OCCDR);
-	} else {
-		__raw_writel(addr, IOP13XX_ATUE_OCCAR);
-		__raw_writel(value, IOP13XX_ATUE_OCCDR);
-	}
-
-	return PCIBIOS_SUCCESSFUL;
-}
-
-static struct pci_ops iop13xx_atue_ops = {
-	.read	= iop13xx_atue_read_config,
-	.write	= iop13xx_atue_write_config,
-};
-
-/* When a PCI device does not exist during config cycles, the XScale gets a
- * bus error instead of returning 0xffffffff.  We can't rely on the ATU status
- * bits to tell us that it was indeed a configuration cycle that caused this
- * error especially in the case when the ATUE link is down.  Instead we rely
- * on data from the south XSI bridge to validate the abort
- */
-int
-iop13xx_pci_abort(unsigned long addr, unsigned int fsr, struct pt_regs *regs)
-{
-	PRINTK("Data abort: address = 0x%08lx "
-		    "fsr = 0x%03x PC = 0x%08lx LR = 0x%08lx",
-		addr, fsr, regs->ARM_pc, regs->ARM_lr);
-
-	PRINTK("IOP13XX_XBG_BECSR: %#10x", __raw_readl(IOP13XX_XBG_BECSR));
-	PRINTK("IOP13XX_XBG_BERAR: %#10x", __raw_readl(IOP13XX_XBG_BERAR));
-	PRINTK("IOP13XX_XBG_BERUAR: %#10x", __raw_readl(IOP13XX_XBG_BERUAR));
-
-	/*  If it was an imprecise abort, then we need to correct the
-	 *  return address to be _after_ the instruction.
-	 */
-	if (fsr & (1 << 10))
-		regs->ARM_pc += 4;
-
-	if (is_atue_occdr_error() || is_atux_occdr_error())
-		return 0;
-	else
-		return 1;
-}
-
-/* Scan an IOP13XX PCI bus.  nr selects which ATU we use.
- */
-int iop13xx_scan_bus(int nr, struct pci_host_bridge *bridge)
-{
-	int which_atu, ret;
-	struct pci_sys_data *sys = pci_host_bridge_priv(bridge);
-
-	switch (init_atu) {
-	case IOP13XX_INIT_ATU_ATUX:
-		which_atu = nr ? 0 : IOP13XX_INIT_ATU_ATUX;
-		break;
-	case IOP13XX_INIT_ATU_ATUE:
-		which_atu = nr ? 0 : IOP13XX_INIT_ATU_ATUE;
-		break;
-	case (IOP13XX_INIT_ATU_ATUX | IOP13XX_INIT_ATU_ATUE):
-		which_atu = nr ? IOP13XX_INIT_ATU_ATUE : IOP13XX_INIT_ATU_ATUX;
-		break;
-	default:
-		which_atu = 0;
-	}
-
-	if (!which_atu) {
-		BUG();
-		return -ENODEV;
-	}
-
-	list_splice_init(&sys->resources, &bridge->windows);
-	bridge->dev.parent = NULL;
-	bridge->sysdata = sys;
-	bridge->busnr = sys->busnr;
-
-	switch (which_atu) {
-	case IOP13XX_INIT_ATU_ATUX:
-		if (time_after_eq(jiffies + msecs_to_jiffies(1000),
-				  atux_trhfa_timeout))  /* ensure not wrap */
-			while(time_before(jiffies, atux_trhfa_timeout))
-				udelay(100);
-
-		bridge->ops = &iop13xx_atux_ops;
-		ret = pci_scan_root_bus_bridge(bridge);
-		if (!ret)
-			pci_bus_atux = bridge->bus;
-		break;
-	case IOP13XX_INIT_ATU_ATUE:
-		bridge->ops = &iop13xx_atue_ops;
-		ret = pci_scan_root_bus_bridge(bridge);
-		if (!ret)
-			pci_bus_atue = bridge->bus;
-		break;
-	default:
-		ret = -EINVAL;
-	}
-
-	return ret;
-}
-
-/* This function is called from iop13xx_pci_init() after assigning valid
- * values to iop13xx_atue_pmmr_offset.  This is the location for common
- * setup of ATUE for all IOP13XX implementations.
- */
-void __init iop13xx_atue_setup(void)
-{
-	int func = iop13xx_atu_function(IOP13XX_INIT_ATU_ATUE);
-	u32 reg_val;
-
-#ifdef CONFIG_PCI_MSI
-	/* BAR 0 (inbound msi window) */
-	__raw_writel(IOP13XX_MU_BASE_PHYS, IOP13XX_MU_MUBAR);
-	__raw_writel(~(IOP13XX_MU_WINDOW_SIZE - 1), IOP13XX_ATUE_IALR0);
-	__raw_writel(IOP13XX_MU_BASE_PHYS, IOP13XX_ATUE_IATVR0);
-	__raw_writel(IOP13XX_MU_BASE_PCI, IOP13XX_ATUE_IABAR0);
-#endif
-
-	/* BAR 1 (1:1 mapping with Physical RAM) */
-	/* Set limit and enable */
-	__raw_writel(~(IOP13XX_MAX_RAM_SIZE - PHYS_OFFSET - 1) & ~0x1,
-			IOP13XX_ATUE_IALR1);
-	__raw_writel(0x0, IOP13XX_ATUE_IAUBAR1);
-
-	/* Set base at the top of the reserved address space */
-	__raw_writel(PHYS_OFFSET | PCI_BASE_ADDRESS_MEM_TYPE_64 |
-			PCI_BASE_ADDRESS_MEM_PREFETCH, IOP13XX_ATUE_IABAR1);
-
-	/* 1:1 mapping with physical ram
-	 * (leave big endian byte swap disabled)
-	 */
-	 __raw_writel(0x0, IOP13XX_ATUE_IAUTVR1);
-	 __raw_writel(PHYS_OFFSET, IOP13XX_ATUE_IATVR1);
-
-	/* Outbound window 1 (PCIX/PCIE memory window) */
-	/* 32 bit Address Space */
-	__raw_writel(0x0, IOP13XX_ATUE_OUMWTVR1);
-	/* PA[35:32] */
-	__raw_writel(IOP13XX_ATUE_OUMBAR_ENABLE |
-			(IOP13XX_PCIE_MEM_PHYS_OFFSET >> 32),
-			IOP13XX_ATUE_OUMBAR1);
-
-	/* Setup the I/O Bar
-	 * A[35-16] in 31-12
-	 */
-	__raw_writel(((IOP13XX_PCIE_LOWER_IO_PA >> 0x4) & 0xfffff000),
-		IOP13XX_ATUE_OIOBAR);
-	__raw_writel(IOP13XX_PCIE_LOWER_IO_BA, IOP13XX_ATUE_OIOWTVR);
-
-	/* clear startup errors */
-	iop13xx_atue_pci_status(1);
-
-	/* OIOBAR function number
-	 */
-	reg_val = __raw_readl(IOP13XX_ATUE_OIOBAR);
-	reg_val &= ~0x7;
-	reg_val |= func;
-	__raw_writel(reg_val, IOP13XX_ATUE_OIOBAR);
-
-	/* OUMBAR function numbers
-	 */
-	reg_val = __raw_readl(IOP13XX_ATUE_OUMBAR0);
-	reg_val &= ~(IOP13XX_ATU_OUMBAR_FUNC_NUM_MASK <<
-			IOP13XX_ATU_OUMBAR_FUNC_NUM);
-	reg_val |= func << IOP13XX_ATU_OUMBAR_FUNC_NUM;
-	__raw_writel(reg_val, IOP13XX_ATUE_OUMBAR0);
-
-	reg_val = __raw_readl(IOP13XX_ATUE_OUMBAR1);
-	reg_val &= ~(IOP13XX_ATU_OUMBAR_FUNC_NUM_MASK <<
-			IOP13XX_ATU_OUMBAR_FUNC_NUM);
-	reg_val |= func << IOP13XX_ATU_OUMBAR_FUNC_NUM;
-	__raw_writel(reg_val, IOP13XX_ATUE_OUMBAR1);
-
-	reg_val = __raw_readl(IOP13XX_ATUE_OUMBAR2);
-	reg_val &= ~(IOP13XX_ATU_OUMBAR_FUNC_NUM_MASK <<
-			IOP13XX_ATU_OUMBAR_FUNC_NUM);
-	reg_val |= func << IOP13XX_ATU_OUMBAR_FUNC_NUM;
-	__raw_writel(reg_val, IOP13XX_ATUE_OUMBAR2);
-
-	reg_val = __raw_readl(IOP13XX_ATUE_OUMBAR3);
-	reg_val &= ~(IOP13XX_ATU_OUMBAR_FUNC_NUM_MASK <<
-			IOP13XX_ATU_OUMBAR_FUNC_NUM);
-	reg_val |= func << IOP13XX_ATU_OUMBAR_FUNC_NUM;
-	__raw_writel(reg_val, IOP13XX_ATUE_OUMBAR3);
-
-	/* Enable inbound and outbound cycles
-	 */
-	reg_val = __raw_readw(IOP13XX_ATUE_ATUCMD);
-	reg_val |= PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER |
-			PCI_COMMAND_PARITY | PCI_COMMAND_SERR;
-	__raw_writew(reg_val, IOP13XX_ATUE_ATUCMD);
-
-	reg_val = __raw_readl(IOP13XX_ATUE_ATUCR);
-	reg_val |= IOP13XX_ATUE_ATUCR_OUT_EN |
-			IOP13XX_ATUE_ATUCR_IVM;
-	__raw_writel(reg_val, IOP13XX_ATUE_ATUCR);
-}
-
-void __init iop13xx_atue_disable(void)
-{
-	u32 reg_val;
-
-	__raw_writew(0x0, IOP13XX_ATUE_ATUCMD);
-	__raw_writel(IOP13XX_ATUE_ATUCR_IVM, IOP13XX_ATUE_ATUCR);
-
-	/* wait for cycles to quiesce */
-	while (__raw_readl(IOP13XX_ATUE_PCSR) & (IOP13XX_ATUE_PCSR_OUT_Q_BUSY |
-					     IOP13XX_ATUE_PCSR_IN_Q_BUSY |
-					     IOP13XX_ATUE_PCSR_LLRB_BUSY))
-		cpu_relax();
-
-	/* BAR 0 ( Disabled ) */
-	__raw_writel(0x0, IOP13XX_ATUE_IAUBAR0);
-	__raw_writel(0x0, IOP13XX_ATUE_IABAR0);
-	__raw_writel(0x0, IOP13XX_ATUE_IAUTVR0);
-	__raw_writel(0x0, IOP13XX_ATUE_IATVR0);
-	__raw_writel(0x0, IOP13XX_ATUE_IALR0);
-	reg_val = __raw_readl(IOP13XX_ATUE_OUMBAR0);
-	reg_val &= ~IOP13XX_ATUE_OUMBAR_ENABLE;
-	__raw_writel(reg_val, IOP13XX_ATUE_OUMBAR0);
-
-	/* BAR 1 ( Disabled ) */
-	__raw_writel(0x0, IOP13XX_ATUE_IAUBAR1);
-	__raw_writel(0x0, IOP13XX_ATUE_IABAR1);
-	__raw_writel(0x0, IOP13XX_ATUE_IAUTVR1);
-	__raw_writel(0x0, IOP13XX_ATUE_IATVR1);
-	__raw_writel(0x0, IOP13XX_ATUE_IALR1);
-	reg_val = __raw_readl(IOP13XX_ATUE_OUMBAR1);
-	reg_val &= ~IOP13XX_ATUE_OUMBAR_ENABLE;
-	__raw_writel(reg_val, IOP13XX_ATUE_OUMBAR1);
-
-	/* BAR 2 ( Disabled ) */
-	__raw_writel(0x0, IOP13XX_ATUE_IAUBAR2);
-	__raw_writel(0x0, IOP13XX_ATUE_IABAR2);
-	__raw_writel(0x0, IOP13XX_ATUE_IAUTVR2);
-	__raw_writel(0x0, IOP13XX_ATUE_IATVR2);
-	__raw_writel(0x0, IOP13XX_ATUE_IALR2);
-	reg_val = __raw_readl(IOP13XX_ATUE_OUMBAR2);
-	reg_val &= ~IOP13XX_ATUE_OUMBAR_ENABLE;
-	__raw_writel(reg_val, IOP13XX_ATUE_OUMBAR2);
-
-	/* BAR 3 ( Disabled ) */
-	reg_val = __raw_readl(IOP13XX_ATUE_OUMBAR3);
-	reg_val &= ~IOP13XX_ATUE_OUMBAR_ENABLE;
-	__raw_writel(reg_val, IOP13XX_ATUE_OUMBAR3);
-
-	/* Setup the I/O Bar
-	 * A[35-16] in 31-12
-	 */
-	__raw_writel((IOP13XX_PCIE_LOWER_IO_PA >> 0x4) & 0xfffff000,
-			IOP13XX_ATUE_OIOBAR);
-	__raw_writel(IOP13XX_PCIE_LOWER_IO_BA, IOP13XX_ATUE_OIOWTVR);
-}
-
-/* This function is called from iop13xx_pci_init() after assigning valid
- * values to iop13xx_atux_pmmr_offset.  This is the location for common
- * setup of ATUX for all IOP13XX implementations.
- */
-void __init iop13xx_atux_setup(void)
-{
-	u32 reg_val;
-	int func = iop13xx_atu_function(IOP13XX_INIT_ATU_ATUX);
-
-	/* Take PCI-X bus out of reset if bootloader hasn't already.
-	 * According to spec, we should wait for 2^25 PCI clocks to meet
-	 * the PCI timing parameter Trhfa (RST# high to first access).
-	 * This is rarely necessary and often ignored.
-	 */
-	reg_val = __raw_readl(IOP13XX_ATUX_PCSR);
-	if (reg_val & IOP13XX_ATUX_PCSR_P_RSTOUT) {
-		int msec = (reg_val >> IOP13XX_ATUX_PCSR_FREQ_OFFSET) & 0x7;
-		msec = 1000 / (8-msec); /* bits 100=133MHz, 111=>33MHz */
-		__raw_writel(reg_val & ~IOP13XX_ATUX_PCSR_P_RSTOUT,
-				IOP13XX_ATUX_PCSR);
-		atux_trhfa_timeout = jiffies + msecs_to_jiffies(msec);
-	}
-	else
-		atux_trhfa_timeout = jiffies;
-
-#ifdef CONFIG_PCI_MSI
-	/* BAR 0 (inbound msi window) */
-	__raw_writel(IOP13XX_MU_BASE_PHYS, IOP13XX_MU_MUBAR);
-	__raw_writel(~(IOP13XX_MU_WINDOW_SIZE - 1), IOP13XX_ATUX_IALR0);
-	__raw_writel(IOP13XX_MU_BASE_PHYS, IOP13XX_ATUX_IATVR0);
-	__raw_writel(IOP13XX_MU_BASE_PCI, IOP13XX_ATUX_IABAR0);
-#endif
-
-	/* BAR 1 (1:1 mapping with Physical RAM) */
-	/* Set limit and enable */
-	__raw_writel(~(IOP13XX_MAX_RAM_SIZE - PHYS_OFFSET - 1) & ~0x1,
-			IOP13XX_ATUX_IALR1);
-	__raw_writel(0x0, IOP13XX_ATUX_IAUBAR1);
-
-	/* Set base at the top of the reserved address space */
-	__raw_writel(PHYS_OFFSET | PCI_BASE_ADDRESS_MEM_TYPE_64 |
-			PCI_BASE_ADDRESS_MEM_PREFETCH, IOP13XX_ATUX_IABAR1);
-
-	/* 1:1 mapping with physical ram
-	 * (leave big endian byte swap disabled)
-	 */
-	__raw_writel(0x0, IOP13XX_ATUX_IAUTVR1);
-	__raw_writel(PHYS_OFFSET, IOP13XX_ATUX_IATVR1);
-
-	/* Outbound window 1 (PCIX/PCIE memory window) */
-	/* 32 bit Address Space */
-	__raw_writel(0x0, IOP13XX_ATUX_OUMWTVR1);
-	/* PA[35:32] */
-	__raw_writel(IOP13XX_ATUX_OUMBAR_ENABLE |
-			IOP13XX_PCIX_MEM_PHYS_OFFSET >> 32,
-			IOP13XX_ATUX_OUMBAR1);
-
-	/* Setup the I/O Bar
-	 * A[35-16] in 31-12
-	 */
-	__raw_writel((IOP13XX_PCIX_LOWER_IO_PA >> 0x4) & 0xfffff000,
-		IOP13XX_ATUX_OIOBAR);
-	__raw_writel(IOP13XX_PCIX_LOWER_IO_BA, IOP13XX_ATUX_OIOWTVR);
-
-	/* clear startup errors */
-	iop13xx_atux_pci_status(1);
-
-	/* OIOBAR function number
-	 */
-	reg_val = __raw_readl(IOP13XX_ATUX_OIOBAR);
-	reg_val &= ~0x7;
-	reg_val |= func;
-	__raw_writel(reg_val, IOP13XX_ATUX_OIOBAR);
-
-	/* OUMBAR function numbers
-	 */
-	reg_val = __raw_readl(IOP13XX_ATUX_OUMBAR0);
-	reg_val &= ~(IOP13XX_ATU_OUMBAR_FUNC_NUM_MASK <<
-			IOP13XX_ATU_OUMBAR_FUNC_NUM);
-	reg_val |= func << IOP13XX_ATU_OUMBAR_FUNC_NUM;
-	__raw_writel(reg_val, IOP13XX_ATUX_OUMBAR0);
-
-	reg_val = __raw_readl(IOP13XX_ATUX_OUMBAR1);
-	reg_val &= ~(IOP13XX_ATU_OUMBAR_FUNC_NUM_MASK <<
-			IOP13XX_ATU_OUMBAR_FUNC_NUM);
-	reg_val |= func << IOP13XX_ATU_OUMBAR_FUNC_NUM;
-	__raw_writel(reg_val, IOP13XX_ATUX_OUMBAR1);
-
-	reg_val = __raw_readl(IOP13XX_ATUX_OUMBAR2);
-	reg_val &= ~(IOP13XX_ATU_OUMBAR_FUNC_NUM_MASK <<
-			IOP13XX_ATU_OUMBAR_FUNC_NUM);
-	reg_val |= func << IOP13XX_ATU_OUMBAR_FUNC_NUM;
-	__raw_writel(reg_val, IOP13XX_ATUX_OUMBAR2);
-
-	reg_val = __raw_readl(IOP13XX_ATUX_OUMBAR3);
-	reg_val &= ~(IOP13XX_ATU_OUMBAR_FUNC_NUM_MASK <<
-			IOP13XX_ATU_OUMBAR_FUNC_NUM);
-	reg_val |= func << IOP13XX_ATU_OUMBAR_FUNC_NUM;
-	__raw_writel(reg_val, IOP13XX_ATUX_OUMBAR3);
-
-	/* Enable inbound and outbound cycles
-	 */
-	reg_val = __raw_readw(IOP13XX_ATUX_ATUCMD);
-	reg_val |= PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER |
-		        PCI_COMMAND_PARITY | PCI_COMMAND_SERR;
-	__raw_writew(reg_val, IOP13XX_ATUX_ATUCMD);
-
-	reg_val = __raw_readl(IOP13XX_ATUX_ATUCR);
-	reg_val |= IOP13XX_ATUX_ATUCR_OUT_EN;
-	__raw_writel(reg_val, IOP13XX_ATUX_ATUCR);
-}
-
-void __init iop13xx_atux_disable(void)
-{
-	u32 reg_val;
-
-	__raw_writew(0x0, IOP13XX_ATUX_ATUCMD);
-	__raw_writel(0x0, IOP13XX_ATUX_ATUCR);
-
-	/* wait for cycles to quiesce */
-	while (__raw_readl(IOP13XX_ATUX_PCSR) & (IOP13XX_ATUX_PCSR_OUT_Q_BUSY |
-				     IOP13XX_ATUX_PCSR_IN_Q_BUSY))
-		cpu_relax();
-
-	/* BAR 0 ( Disabled ) */
-	__raw_writel(0x0, IOP13XX_ATUX_IAUBAR0);
-	__raw_writel(0x0, IOP13XX_ATUX_IABAR0);
-	__raw_writel(0x0, IOP13XX_ATUX_IAUTVR0);
-	__raw_writel(0x0, IOP13XX_ATUX_IATVR0);
-	__raw_writel(0x0, IOP13XX_ATUX_IALR0);
-	reg_val = __raw_readl(IOP13XX_ATUX_OUMBAR0);
-	reg_val &= ~IOP13XX_ATUX_OUMBAR_ENABLE;
-	__raw_writel(reg_val, IOP13XX_ATUX_OUMBAR0);
-
-	/* BAR 1 ( Disabled ) */
-	__raw_writel(0x0, IOP13XX_ATUX_IAUBAR1);
-	__raw_writel(0x0, IOP13XX_ATUX_IABAR1);
-	__raw_writel(0x0, IOP13XX_ATUX_IAUTVR1);
-	__raw_writel(0x0, IOP13XX_ATUX_IATVR1);
-	__raw_writel(0x0, IOP13XX_ATUX_IALR1);
-	reg_val = __raw_readl(IOP13XX_ATUX_OUMBAR1);
-	reg_val &= ~IOP13XX_ATUX_OUMBAR_ENABLE;
-	__raw_writel(reg_val, IOP13XX_ATUX_OUMBAR1);
-
-	/* BAR 2 ( Disabled ) */
-	__raw_writel(0x0, IOP13XX_ATUX_IAUBAR2);
-	__raw_writel(0x0, IOP13XX_ATUX_IABAR2);
-	__raw_writel(0x0, IOP13XX_ATUX_IAUTVR2);
-	__raw_writel(0x0, IOP13XX_ATUX_IATVR2);
-	__raw_writel(0x0, IOP13XX_ATUX_IALR2);
-	reg_val = __raw_readl(IOP13XX_ATUX_OUMBAR2);
-	reg_val &= ~IOP13XX_ATUX_OUMBAR_ENABLE;
-	__raw_writel(reg_val, IOP13XX_ATUX_OUMBAR2);
-
-	/* BAR 3 ( Disabled ) */
-	__raw_writel(0x0, IOP13XX_ATUX_IAUBAR3);
-	__raw_writel(0x0, IOP13XX_ATUX_IABAR3);
-	__raw_writel(0x0, IOP13XX_ATUX_IAUTVR3);
-	__raw_writel(0x0, IOP13XX_ATUX_IATVR3);
-	__raw_writel(0x0, IOP13XX_ATUX_IALR3);
-	reg_val = __raw_readl(IOP13XX_ATUX_OUMBAR3);
-	reg_val &= ~IOP13XX_ATUX_OUMBAR_ENABLE;
-	__raw_writel(reg_val, IOP13XX_ATUX_OUMBAR3);
-
-	/* Setup the I/O Bar
-	* A[35-16] in 31-12
-	*/
-	__raw_writel((IOP13XX_PCIX_LOWER_IO_PA >> 0x4) & 0xfffff000,
-			IOP13XX_ATUX_OIOBAR);
-	__raw_writel(IOP13XX_PCIX_LOWER_IO_BA, IOP13XX_ATUX_OIOWTVR);
-}
-
-void __init iop13xx_set_atu_mmr_bases(void)
-{
-	/* Based on ESSR0, determine the ATU X/E offsets */
-	switch(__raw_readl(IOP13XX_ESSR0) &
-		(IOP13XX_CONTROLLER_ONLY | IOP13XX_INTERFACE_SEL_PCIX)) {
-	/* both asserted */
-	case 0:
-		iop13xx_atux_pmmr_offset = IOP13XX_ATU1_PMMR_OFFSET;
-		iop13xx_atue_pmmr_offset = IOP13XX_ATU2_PMMR_OFFSET;
-		break;
-	/* IOP13XX_CONTROLLER_ONLY = deasserted
-	 * IOP13XX_INTERFACE_SEL_PCIX = asserted
-	 */
-	case IOP13XX_CONTROLLER_ONLY:
-		iop13xx_atux_pmmr_offset = IOP13XX_ATU0_PMMR_OFFSET;
-		iop13xx_atue_pmmr_offset = IOP13XX_ATU2_PMMR_OFFSET;
-		break;
-	/* IOP13XX_CONTROLLER_ONLY = asserted
-	 * IOP13XX_INTERFACE_SEL_PCIX = deasserted
-	 */
-	case IOP13XX_INTERFACE_SEL_PCIX:
-		iop13xx_atux_pmmr_offset = IOP13XX_ATU1_PMMR_OFFSET;
-		iop13xx_atue_pmmr_offset = IOP13XX_ATU2_PMMR_OFFSET;
-		break;
-	/* both deasserted */
-	case IOP13XX_CONTROLLER_ONLY | IOP13XX_INTERFACE_SEL_PCIX:
-		iop13xx_atux_pmmr_offset = IOP13XX_ATU2_PMMR_OFFSET;
-		iop13xx_atue_pmmr_offset = IOP13XX_ATU0_PMMR_OFFSET;
-		break;
-	default:
-		BUG();
-	}
-}
-
-void __init iop13xx_atu_select(struct hw_pci *plat_pci)
-{
-	int i;
-
-	/* set system defaults
-	 * note: if "iop13xx_init_atu=" is specified this autodetect
-	 * sequence will be bypassed
-	 */
-	if (init_atu == IOP13XX_INIT_ATU_DEFAULT) {
-		/* check for single/dual interface */
-		if (__raw_readl(IOP13XX_ESSR0) & IOP13XX_INTERFACE_SEL_PCIX) {
-			/* ATUE must be present check the device id
-			 * to see if ATUX is present.
-			 */
-			init_atu |= IOP13XX_INIT_ATU_ATUE;
-			switch (__raw_readw(IOP13XX_ATUE_DID) & 0xf0) {
-			case 0x70:
-			case 0x80:
-			case 0xc0:
-				init_atu |= IOP13XX_INIT_ATU_ATUX;
-				break;
-			}
-		} else {
-			/* ATUX must be present check the device id
-			 * to see if ATUE is present.
-			 */
-			init_atu |= IOP13XX_INIT_ATU_ATUX;
-			switch (__raw_readw(IOP13XX_ATUX_DID) & 0xf0) {
-			case 0x70:
-			case 0x80:
-			case 0xc0:
-				init_atu |= IOP13XX_INIT_ATU_ATUE;
-				break;
-			}
-		}
-
-		/* check central resource and root complex capability */
-		if (init_atu & IOP13XX_INIT_ATU_ATUX)
-			if (!(__raw_readl(IOP13XX_ATUX_PCSR) &
-				IOP13XX_ATUX_PCSR_CENTRAL_RES))
-				init_atu &= ~IOP13XX_INIT_ATU_ATUX;
-
-		if (init_atu & IOP13XX_INIT_ATU_ATUE)
-			if (__raw_readl(IOP13XX_ATUE_PCSR) &
-				IOP13XX_ATUE_PCSR_END_POINT)
-				init_atu &= ~IOP13XX_INIT_ATU_ATUE;
-	}
-
-	for (i = 0; i < 2; i++) {
-		if((init_atu & (1 << i)) == (1 << i))
-			plat_pci->nr_controllers++;
-	}
-}
-
-void __init iop13xx_pci_init(void)
-{
-	/* clear pre-existing south bridge errors */
-	__raw_writel(__raw_readl(IOP13XX_XBG_BECSR) & 3, IOP13XX_XBG_BECSR);
-
-	/* Setup the Min Address for PCI memory... */
-	pcibios_min_mem = IOP13XX_PCIX_LOWER_MEM_BA;
-
-	/* if Linux is given control of an ATU
-	 * clear out its prior configuration,
-	 * otherwise do not touch the registers
-	 */
-	if (init_atu & IOP13XX_INIT_ATU_ATUE) {
-		iop13xx_atue_disable();
-		iop13xx_atue_setup();
-	}
-
-	if (init_atu & IOP13XX_INIT_ATU_ATUX) {
-		iop13xx_atux_disable();
-		iop13xx_atux_setup();
-	}
-
-	hook_fault_code(16+6, iop13xx_pci_abort, SIGBUS, 0,
-			"imprecise external abort");
-}
-
-/* initialize the pci memory space.  handle any combination of
- * atue and atux enabled/disabled
- */
-int iop13xx_pci_setup(int nr, struct pci_sys_data *sys)
-{
-	struct resource *res;
-	int which_atu;
-	u32 pcixsr, pcsr;
-
-	if (nr > 1)
-		return 0;
-
-	res = kzalloc(sizeof(struct resource), GFP_KERNEL);
-	if (!res)
-		panic("PCI: unable to alloc resources");
-
-
-	/* 'nr' assumptions:
-	 * ATUX is always 0
-	 * ATUE is 1 when ATUX is also enabled
-	 * ATUE is 0 when ATUX is disabled
-	 */
-	switch(init_atu) {
-	case IOP13XX_INIT_ATU_ATUX:
-		which_atu = nr ? 0 : IOP13XX_INIT_ATU_ATUX;
-		break;
-	case IOP13XX_INIT_ATU_ATUE:
-		which_atu = nr ? 0 : IOP13XX_INIT_ATU_ATUE;
-		break;
-	case (IOP13XX_INIT_ATU_ATUX | IOP13XX_INIT_ATU_ATUE):
-		which_atu = nr ? IOP13XX_INIT_ATU_ATUE : IOP13XX_INIT_ATU_ATUX;
-		break;
-	default:
-		which_atu = 0;
-	}
-
-	if (!which_atu) {
-		kfree(res);
-		return 0;
-	}
-
-	switch(which_atu) {
-	case IOP13XX_INIT_ATU_ATUX:
-		pcixsr = __raw_readl(IOP13XX_ATUX_PCIXSR);
-		pcixsr &= ~0xffff;
-		pcixsr |= sys->busnr << IOP13XX_ATUX_PCIXSR_BUS_NUM |
-			  0 << IOP13XX_ATUX_PCIXSR_DEV_NUM |
-			  iop13xx_atu_function(IOP13XX_INIT_ATU_ATUX)
-				  << IOP13XX_ATUX_PCIXSR_FUNC_NUM;
-		__raw_writel(pcixsr, IOP13XX_ATUX_PCIXSR);
-
-		pci_ioremap_io(0, IOP13XX_PCIX_LOWER_IO_PA);
-
-		res->start = IOP13XX_PCIX_LOWER_MEM_RA;
-		res->end   = IOP13XX_PCIX_UPPER_MEM_RA;
-		res->name  = "IQ81340 ATUX PCI Memory Space";
-		res->flags = IORESOURCE_MEM;
-		sys->mem_offset = IOP13XX_PCIX_MEM_OFFSET;
-		break;
-	case IOP13XX_INIT_ATU_ATUE:
-		/* Note: the function number field in the PCSR is ro */
-		pcsr = __raw_readl(IOP13XX_ATUE_PCSR);
-		pcsr &= ~(0xfff8 << 16);
-		pcsr |= sys->busnr << IOP13XX_ATUE_PCSR_BUS_NUM |
-				0 << IOP13XX_ATUE_PCSR_DEV_NUM;
-
-		__raw_writel(pcsr, IOP13XX_ATUE_PCSR);
-
-		pci_ioremap_io(SZ_64K, IOP13XX_PCIE_LOWER_IO_PA);
-
-		res->start = IOP13XX_PCIE_LOWER_MEM_RA;
-		res->end   = IOP13XX_PCIE_UPPER_MEM_RA;
-		res->name  = "IQ81340 ATUE PCI Memory Space";
-		res->flags = IORESOURCE_MEM;
-		sys->mem_offset = IOP13XX_PCIE_MEM_OFFSET;
-		sys->map_irq = iop13xx_pcie_map_irq;
-		break;
-	default:
-		kfree(res);
-		return 0;
-	}
-
-	request_resource(&iomem_resource, res);
-
-	pci_add_resource_offset(&sys->resources, res, sys->mem_offset);
-
-	return 1;
-}
-
-u16 iop13xx_dev_id(void)
-{
-	if (__raw_readl(IOP13XX_ESSR0) & IOP13XX_INTERFACE_SEL_PCIX)
-		return __raw_readw(IOP13XX_ATUE_DID);
-	else
-		return __raw_readw(IOP13XX_ATUX_DID);
-}
-
-static int __init iop13xx_init_atu_setup(char *str)
-{
-        init_atu = IOP13XX_INIT_ATU_NONE;
-        if (str) {
-                while (*str != '\0') {
-                        switch (*str) {
-                        case 'x':
-                        case 'X':
-                                init_atu |= IOP13XX_INIT_ATU_ATUX;
-                                init_atu &= ~IOP13XX_INIT_ATU_NONE;
-                                break;
-                        case 'e':
-                        case 'E':
-                                init_atu |= IOP13XX_INIT_ATU_ATUE;
-                                init_atu &= ~IOP13XX_INIT_ATU_NONE;
-                                break;
-                        case ',':
-                        case '=':
-                                break;
-                        default:
-                                PRINTK("\"iop13xx_init_atu\" malformed at "
-                                            "character: \'%c\'", *str);
-                                *(str + 1) = '\0';
-                                init_atu = IOP13XX_INIT_ATU_DEFAULT;
-                        }
-                        str++;
-                }
-        }
-        return 1;
-}
-
-__setup("iop13xx_init_atu", iop13xx_init_atu_setup);