Merge tag 'amlogic-dt-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt

Pull "Amlogic 32-bit DT updates for v4.17" from Kevin Hilman:

- odroid-c1: add microSD, ethernet, USB reset
- add reset controller
- fix requesting GPIOs greater than GPIOZ_3

* tag 'amlogic-dt-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  ARM: dts: meson8b: the CBUS GPIO controller only has 83 GPIOs
  ARM: dts: meson8b-odroidc1: add microSD support
  ARM: dts: meson8b: add the I2C clocks
  ARM: dts: meson8b-odroidc1: ethernet support
  ARM: dts: meson8b: extend ethernet controller description
  ARM: dts: meson8: add the USB reset line
  ARM: dts: meson8: add the reset controller
  ARM: dts: meson8b: grow the reset controller memory zone

3 files changed, 152 insertions, 4 deletions

diff --git a/arch/arm/boot/dts/meson8.dtsi b/arch/arm/boot/dts/meson8.dtsi
index d2e3eeaa1a5f..dcc9292d2ffa 100644
--- a/arch/arm/boot/dts/meson8.dtsi
+++ b/arch/arm/boot/dts/meson8.dtsi
@@ -46,6 +46,7 @@
 #include <dt-bindings/clock/meson8b-clkc.h>
 #include <dt-bindings/gpio/meson8-gpio.h>
 #include <dt-bindings/reset/amlogic,meson8b-clkc-reset.h>
+#include <dt-bindings/reset/amlogic,meson8b-reset.h>
 #include "meson.dtsi"
 
 / {
@@ -187,6 +188,12 @@
 		reg = <0x8000 0x4>, <0x4000 0x460>;
 	};
 
+	reset: reset-controller@4404 {
+		compatible = "amlogic,meson8b-reset";
+		reg = <0x4404 0x9c>;
+		#reset-cells = <1>;
+	};
+
 	analog_top: analog-top@81a8 {
 		compatible = "amlogic,meson8-analog-top", "syscon";
 		reg = <0x81a8 0x14>;
@@ -383,10 +390,12 @@
 	compatible = "amlogic,meson8-usb2-phy", "amlogic,meson-mx-usb2-phy";
 	clocks = <&clkc CLKID_USB>, <&clkc CLKID_USB0>;
 	clock-names = "usb_general", "usb";
+	resets = <&reset RESET_USB_OTG>;
 };
 
 &usb1_phy {
 	compatible = "amlogic,meson8-usb2-phy", "amlogic,meson-mx-usb2-phy";
 	clocks = <&clkc CLKID_USB>, <&clkc CLKID_USB1>;
 	clock-names = "usb_general", "usb";
+	resets = <&reset RESET_USB_OTG>;
 };
diff --git a/arch/arm/boot/dts/meson8b-odroidc1.dts b/arch/arm/boot/dts/meson8b-odroidc1.dts
index 9ff6ca4e20d0..3a5603d95b70 100644
--- a/arch/arm/boot/dts/meson8b-odroidc1.dts
+++ b/arch/arm/boot/dts/meson8b-odroidc1.dts
@@ -54,6 +54,7 @@
 
 	aliases {
 		serial0 = &uart_AO;
+		mmc0 = &sd_card_slot;
 	};
 
 	memory {
@@ -69,6 +70,37 @@
 			default-state = "off";
 		};
 	};
+
+	tflash_vdd: regulator-tflash_vdd {
+		/*
+		 * signal name from schematics: TFLASH_VDD_EN
+		 */
+		compatible = "regulator-fixed";
+
+		regulator-name = "TFLASH_VDD";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&gpio GPIOY_12 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	tf_io: gpio-regulator-tf_io {
+		compatible = "regulator-gpio";
+
+		regulator-name = "TF_IO";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+
+		/*
+		 * signal name from schematics: TF_3V3N_1V8_EN
+		 */
+		gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_HIGH>;
+		gpios-states = <0>;
+
+		states = <3300000 0
+			  1800000 1>;
+	};
 };
 
 &uart_AO {
@@ -99,3 +131,59 @@
 &usb1 {
 	status = "okay";
 };
+
+&sdio {
+	status = "okay";
+
+	pinctrl-0 = <&sd_b_pins>;
+	pinctrl-names = "default";
+
+	/* SD card */
+	sd_card_slot: slot@1 {
+		compatible = "mmc-slot";
+		reg = <1>;
+		status = "okay";
+
+		bus-width = <4>;
+		no-sdio;
+		cap-mmc-highspeed;
+		cap-sd-highspeed;
+		disable-wp;
+
+		cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
+		cd-inverted;
+
+		vmmc-supply = <&tflash_vdd>;
+		vqmmc-supply = <&tf_io>;
+	};
+};
+
+&ethmac {
+	status = "okay";
+
+	snps,reset-gpio = <&gpio GPIOH_4 GPIO_ACTIVE_HIGH>;
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 30000>;
+
+	pinctrl-0 = <&eth_rgmii_pins>;
+	pinctrl-names = "default";
+
+	phy-mode = "rgmii";
+	phy-handle = <&eth_phy>;
+	amlogic,tx-delay-ns = <4>;
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Realtek RTL8211F (0x001cc916) */
+		eth_phy: ethernet-phy@0 {
+			reg = <0>;
+			eee-broken-1000t;
+			interrupt-parent = <&gpio_intc>;
+			/* GPIOH_3 */
+			interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/meson8b.dtsi b/arch/arm/boot/dts/meson8b.dtsi
index 7cd03ed3742e..553b82174604 100644
--- a/arch/arm/boot/dts/meson8b.dtsi
+++ b/arch/arm/boot/dts/meson8b.dtsi
@@ -152,7 +152,7 @@
 
 	reset: reset-controller@4404 {
 		compatible = "amlogic,meson8b-reset";
-		reg = <0x4404 0x20>;
+		reg = <0x4404 0x9c>;
 		#reset-cells = <1>;
 	};
 
@@ -183,7 +183,36 @@
 			reg-names = "mux", "pull", "pull-enable", "gpio";
 			gpio-controller;
 			#gpio-cells = <2>;
-			gpio-ranges = <&pinctrl_cbus 0 0 130>;
+			gpio-ranges = <&pinctrl_cbus 0 0 83>;
+		};
+
+		eth_rgmii_pins: eth-rgmii {
+			mux {
+				groups = "eth_tx_clk",
+					 "eth_tx_en",
+					 "eth_txd1_0",
+					 "eth_txd1_1",
+					 "eth_txd0_0",
+					 "eth_txd0_1",
+					 "eth_rx_clk",
+					 "eth_rx_dv",
+					 "eth_rxd1",
+					 "eth_rxd0",
+					 "eth_mdio_en",
+					 "eth_mdc",
+					 "eth_ref_clk",
+					 "eth_txd2",
+					 "eth_txd3";
+				function = "ethernet";
+			};
+		};
+
+		sd_b_pins: sd-b {
+			mux {
+				groups = "sd_d0_b", "sd_d1_b", "sd_d2_b",
+					"sd_d3_b", "sd_clk_b", "sd_cmd_b";
+				function = "sd_b";
+			};
 		};
 	};
 };
@@ -203,8 +232,18 @@
 };
 
 &ethmac {
-	clocks = <&clkc CLKID_ETH>;
-	clock-names = "stmmaceth";
+	compatible = "amlogic,meson8b-dwmac", "snps,dwmac-3.70a", "snps,dwmac";
+
+	reg = <0xc9410000 0x10000
+	       0xc1108140 0x4>;
+
+	clocks = <&clkc CLKID_ETH>,
+		 <&clkc CLKID_MPLL2>,
+		 <&clkc CLKID_MPLL2>;
+	clock-names = "stmmaceth", "clkin0", "clkin1";
+
+	resets = <&reset RESET_ETHERNET>;
+	reset-names = "stmmaceth";
 };
 
 &gpio_intc {
@@ -219,6 +258,18 @@
 	clock-names = "core";
 };
 
+&i2c_AO {
+	clocks = <&clkc CLKID_CLK81>;
+};
+
+&i2c_A {
+	clocks = <&clkc CLKID_I2C>;
+};
+
+&i2c_B {
+	clocks = <&clkc CLKID_I2C>;
+};
+
 &L2 {
 	arm,data-latency = <3 3 3>;
 	arm,tag-latency = <2 2 2>;