Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC fixes from Arnd Bergmann:
 "A new set of bug fixes for 3.16, containing patches for seven
  platforms:

  at91:
    - drivers/misc fix for Kconfig PWM symbol
    - correction of several values in DT after conversion to CCF
    - fix at91sam9261/at91sam9261ek mistake in slow crystal vs. slow RC osc

  imx:
    - Use GPIO for card CD/WP on imx51-babbage and eukrea-mbimxsd51,
      because controller base CD/WP is not working in esdhc driver due to
      runtime PM support
    - A couple of random ventana gw5xxx board fixes
    - Add IMX_IPUV3_CORE back to defconfig, which gets lost when moving
      IPUv3 driver out of staging tree
    - Fix enet/fec clock selection on imx6sl
    - Fix display node on imx53-m53evk board
    - A couple of Cubox-i updates from Russell, which were omitted from
      the merge window due to dependency

  integrator:
    - fix an OF-related regression against 3.15

  mvebu:
    - mvebu (v7)
       - Fix broken SoC ID detection
       - Select ARM_CPU_SUSPEND for v7
       - Remove armada38x compatible string (no users yet)
       - Enable Dove SoC in mvebu_v7_defconfig
    - kirkwood
       - Fix phy-connection-type on GuruPlug board

  qcom:
    - enable gsbi driver in defconfig
    - fix section mismatch warning in serial driver

  samsung:
    - use WFI macro in platform_do_lowpower because exynos cpuhotplug
      includes a hardcoded WFI instruction and it causes compile error
      in Thumb-2 mode.
    - fix GIC reg sizes for exynos4 SoCs
    - remove reset timer counter value during boot and resume for mct
      to fix a big jump in printk timestamps
    - fix pm code to check cortex-A9 for another exynos SoCs
    - don't rely on firmware's secondary_cpu_start for mcpm

  sti:
    - Ethernet clocks were wrongly defined for STiH415/416 platforms
    - STiH416 B2020 revision E DTS file name contained uppercase, change to
      lowercase"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (33 commits)
  ARM: at91/dt: sam9261: remove slow RC osc
  ARM: at91/dt: define sam9261ek slow crystal frequency
  ARM: at91/dt: sam9261: correctly define mainck
  ARM: at91/dt: sam9n12: correct PLLA ICPLL and OUT values
  ARM: at91/dt: sam9x5: correct PLLA ICPLL and OUT values
  misc: atmel_pwm: fix Kconfig symbols
  ARM: integrator: fix OF-related regression
  ARM: mvebu: Fix the improper use of the compatible string armada38x using a wildcard
  ARM: dts: kirkwood: fix phy-connection-type for Guruplug
  ARM: EXYNOS: Don't rely on firmware's secondary_cpu_start for mcpm
  ARM: dts: imx51-eukrea-mbimxsd51-baseboard: unbreak esdhc.
  ARM: dts: imx51-babbage: Fix esdhc setup
  ARM: dts: mx5: Move the display out of soc {} node
  ARM: dts: mx5: Fix IPU port node placement
  ARM: mvebu: select ARM_CPU_SUSPEND for Marvell EBU v7 platforms
  ARM: mvebu: Fix broken SoC ID detection
  ARM: imx_v6_v7_defconfig: Enable CONFIG_IMX_IPUV3_CORE
  ARM: multi_v7_defconfig: Add QCOM GSBI driver
  ARM: stih41x: Rename stih416-b2020-revE.dts to stih416-b2020e.dts
  tty: serial: msm: Fix section mismatch warning
  ...

1 files changed, 27 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/imx6qdl-cubox-i.dtsi b/arch/arm/boot/dts/imx6qdl-cubox-i.dtsi
index 25da82a03110..e8e781656b3f 100644
--- a/arch/arm/boot/dts/imx6qdl-cubox-i.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-cubox-i.dtsi
@@ -12,6 +12,19 @@
 		pinctrl-0 = <&pinctrl_cubox_i_ir>;
 	};
 
+	pwmleds {
+		compatible = "pwm-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_cubox_i_pwm1>;
+
+		front {
+			active-low;
+			label = "imx6:red:front";
+			max-brightness = <248>;
+			pwms = <&pwm1 0 50000>;
+		};
+	};
+
 	regulators {
 		compatible = "simple-bus";
 
@@ -109,6 +122,10 @@
 			>;
 		};
 
+		pinctrl_cubox_i_pwm1: cubox-i-pwm1-front-led {
+			fsl,pins = <MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0>;
+		};
+
 		pinctrl_cubox_i_spdif: cubox-i-spdif {
 			fsl,pins = <MX6QDL_PAD_GPIO_17__SPDIF_OUT 0x13091>;
 		};
@@ -117,6 +134,14 @@
 			fsl,pins = <MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x4001b0b0>;
 		};
 
+		pinctrl_cubox_i_usbotg_id: cubox-i-usbotg-id {
+			/*
+			 * The Cubox-i pulls this low, but as it's pointless
+			 * leaving it as a pull-up, even if it is just 10uA.
+			 */
+			fsl,pins = <MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059>;
+		};
+
 		pinctrl_cubox_i_usbotg_vbus: cubox-i-usbotg-vbus {
 			fsl,pins = <MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x4001b0b0>;
 		};
@@ -153,6 +178,8 @@
 };
 
 &usbotg {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_cubox_i_usbotg_id>;
 	vbus-supply = <&reg_usbotg_vbus>;
 	status = "okay";
 };