Merge tag 'usb-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB / Thunderbolt updates from Greg KH:
 "Here is the big set of Thunderbolt and USB changes for 6.0-rc1.

  Lots of little things here, nothing major, just constant development
  on some new hardware support and cleanups of older drivers. Highlights
  are:

   - lots of typec changes and improvements for new hardware

   - new gadget controller driver

   - thunderbolt support for new hardware

   - the normal set of new usb-serial device ids and cleanups

   - loads of dwc3 controller fixes and improvements

   - mtu3 driver updates

   - testusb fixes for longtime issues (not many people use this tool it
     seems.)

   - minor driver fixes and improvements over the USB tree

   - chromeos platform driver changes were added and then reverted as
     they depened on some typec changes, but the cross-tree merges
     caused problems so they will come back later through the platform
     tree.

  All of these have been in linux-next for a while now with no reported
  issues"

* tag 'usb-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (193 commits)
  usb: misc: onboard_usb_hub: Remove duplicated power_on delay
  usb: misc: onboard_usb_hub: Add TI USB8041 hub support
  usb: misc: onboard_usb_hub: Add reset-gpio support
  USB: usbsevseg: convert sysfs snprintf to sysfs_emit
  dt-bindings: usb: Add binding for TI USB8041 hub controller
  ARM: multi_v7_defconfig: enable USB onboard HUB driver
  ARM: dts: stm32: add support for USB2514B onboard hub on stm32mp15xx-dkx
  usb: misc: onboard-hub: add support for Microchip USB2514B USB 2.0 hub
  dt-bindings: usb: generic-ehci: allow usb-hcd schema properties
  usb: typec: ucsi: stm32g0: add bootloader support
  usb: typec: ucsi: stm32g0: add support for stm32g0 controller
  dt-bindings: usb: typec: add bindings for stm32g0 controller
  usb: typec: ucsi: Acknowledge the GET_ERROR_STATUS command completion
  usb: cdns3: change place of 'priv_ep' assignment in cdns3_gadget_ep_dequeue(), cdns3_gadget_ep_enable()
  usb/chipidea: fix repeated words in comments
  usb: renesas-xhci: Do not print any log while fw verif success
  usb: typec: retimer: Add missing id check in match callback
  USB: xhci: Fix comment typo
  usb/typec/tcpm: fix repeated words in comments
  usb/musb: fix repeated words in comments
  ...

18 files changed, 741 insertions, 27 deletions

diff --git a/Documentation/ABI/testing/configfs-usb-gadget-mass-storage b/Documentation/ABI/testing/configfs-usb-gadget-mass-storage
index c86b63a7bb43..fc0328069267 100644
--- a/Documentation/ABI/testing/configfs-usb-gadget-mass-storage
+++ b/Documentation/ABI/testing/configfs-usb-gadget-mass-storage
@@ -19,7 +19,7 @@ KernelVersion:	3.13
 Description:
 		The attributes:
 
-		===========	==============================================
+		============	==============================================
 		file		The path to the backing file for the LUN.
 				Required if LUN is not marked as removable.
 		ro		Flag specifying access to the LUN shall be
@@ -32,4 +32,10 @@ Description:
 				being a CD-ROM.
 		nofua		Flag specifying that FUA flag
 				in SCSI WRITE(10,12)
-		===========	==============================================
+		forced_eject	This write-only file is useful only when
+				the function is active. It causes the backing
+				file to be forcibly detached from the LUN,
+				regardless of whether the host has allowed it.
+				Any non-zero number of bytes written will
+				result in ejection.
+		============	==============================================
diff --git a/Documentation/ABI/testing/sysfs-bus-platform-onboard-usb-hub b/Documentation/ABI/testing/sysfs-bus-platform-onboard-usb-hub
new file mode 100644
index 000000000000..42deb0552065
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-bus-platform-onboard-usb-hub
@@ -0,0 +1,8 @@
+What:		/sys/bus/platform/devices/<dev>/always_powered_in_suspend
+Date:		June 2022
+KernelVersion:	5.20
+Contact:	Matthias Kaehlcke <matthias@kaehlcke.net>
+		linux-usb@vger.kernel.org
+Description:
+		(RW) Controls whether the USB hub remains always powered
+		during system suspend or not.
\ No newline at end of file
diff --git a/Documentation/ABI/testing/sysfs-bus-usb b/Documentation/ABI/testing/sysfs-bus-usb
index 7efe31ed3a25..568103d3376e 100644
--- a/Documentation/ABI/testing/sysfs-bus-usb
+++ b/Documentation/ABI/testing/sysfs-bus-usb
@@ -253,6 +253,17 @@ Description:
 		only if the system firmware is capable of describing the
 		connection between a port and its connector.
 
+What:		/sys/bus/usb/devices/.../<hub_interface>/port<X>/disable
+Date:		June 2022
+Contact:	Michael Grzeschik <m.grzeschik@pengutronix.de>
+Description:
+		This file controls the state of a USB port, including
+		Vbus power output (but only on hubs that support
+		power switching -- most hubs don't support it). If
+		a port is disabled, the port is unusable: Devices
+		attached to the port will not be detected, initialized,
+		or enumerated.
+
 What:		/sys/bus/usb/devices/.../power/usb2_lpm_l1_timeout
 Date:		May 2013
 Contact:	Mathias Nyman <mathias.nyman@linux.intel.com>
diff --git a/Documentation/ABI/testing/sysfs-class-typec b/Documentation/ABI/testing/sysfs-class-typec
index 75088ecad202..281b995beb05 100644
--- a/Documentation/ABI/testing/sysfs-class-typec
+++ b/Documentation/ABI/testing/sysfs-class-typec
@@ -141,6 +141,14 @@ Description:
 		- "reverse": CC2 orientation
 		- "unknown": Orientation cannot be determined.
 
+What:		/sys/class/typec/<port>/select_usb_power_delivery
+Date:		May 2022
+Contact:	Heikki Krogerus <heikki.krogerus@linux.intel.com>
+Description:
+		Lists the USB Power Delivery Capabilities that the port can
+		advertise to the partner. The currently used capabilities are in
+		brackets. Selection happens by writing to the file.
+
 USB Type-C partner devices (eg. /sys/class/typec/port0-partner/)
 
 What:		/sys/class/typec/<port>-partner/accessory_mode
diff --git a/Documentation/ABI/testing/sysfs-class-usb_power_delivery b/Documentation/ABI/testing/sysfs-class-usb_power_delivery
new file mode 100644
index 000000000000..ce2b1b563cb3
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-class-usb_power_delivery
@@ -0,0 +1,240 @@
+What:		/sys/class/usb_power_delivery
+Date:		May 2022
+Contact:	Heikki Krogerus <heikki.krogerus@linux.intel.com>
+Description:
+		Directory for USB Power Delivery devices.
+
+What:		/sys/class/usb_power_delivery/.../revision
+Date:		May 2022
+Contact:	Heikki Krogerus <heikki.krogerus@linux.intel.com>
+Description:
+		File showing the USB Power Delivery Specification Revision used
+		in communication.
+
+What:		/sys/class/usb_power_delivery/.../version
+Date:		May 2022
+Contact:	Heikki Krogerus <heikki.krogerus@linux.intel.com>
+Description:
+		This is an optional attribute file showing the version of the
+		specific revision of the USB Power Delivery Specification. In
+		most cases the specification version is not known and the file
+		is not available.
+
+What:		/sys/class/usb_power_delivery/.../source-capabilities
+Date:		May 2022
+Contact:	Heikki Krogerus <heikki.krogerus@linux.intel.com>
+Description:
+		The source capabilities message "Source_Capabilities" contains a
+		set of Power Data Objects (PDO), each representing a type of
+		power supply. The order of the PDO objects is defined in the USB
+		Power Delivery Specification. Each PDO - power supply - will
+		have its own device, and the PDO device name will start with the
+		object position number as the first character followed by the
+		power supply type name (":" as delimiter).
+
+			/sys/class/usb_power_delivery/.../source_capabilities/<position>:<type>
+
+What:		/sys/class/usb_power_delivery/.../sink-capabilities
+Date:		May 2022
+Contact:	Heikki Krogerus <heikki.krogerus@linux.intel.com>
+Description:
+		The sink capability message "Sink_Capabilities" contains a set
+		of Power Data Objects (PDO) just like with source capabilities,
+		but instead of describing the power capabilities, these objects
+		describe the power requirements.
+
+		The order of the objects in the sink capability message is the
+		same as with the source capabilities message.
+
+Fixed Supplies
+
+What:		/sys/class/usb_power_delivery/.../<capability>/<position>:fixed_supply
+Date:		May 2022
+Contact:	Heikki Krogerus <heikki.krogerus@linux.intel.com>
+Description:
+		Devices containing the attributes (the bit fields) defined for
+		Fixed Supplies.
+
+		The device "1:fixed_supply" is special. USB Power Delivery
+		Specification dictates that the first PDO (at object position
+		1), and the only mandatory PDO, is always the vSafe5V Fixed
+		Supply Object. vSafe5V Object has additional fields defined for
+		it that the other Fixed Supply Objects do not have and that are
+		related to the USB capabilities rather than power capabilities.
+
+What:		/sys/class/usb_power_delivery/.../<capability>/1:fixed_supply/dual_role_power
+Date:		May 2022
+Contact:	Heikki Krogerus <heikki.krogerus@linux.intel.com>
+Description:
+		This file contains boolean value that tells does the device
+		support both source and sink power roles.
+
+What:		/sys/class/usb_power_delivery/.../<capability>/1:fixed_supply/usb_suspend_supported
+Date:		May 2022
+Contact:	Heikki Krogerus <heikki.krogerus@linux.intel.com>
+Description:
+		This file shows the value of the USB Suspend Supported bit in
+		vSafe5V Fixed Supply Object. If the bit is set then the device
+		will follow the USB 2.0 and USB 3.2 rules for suspend and
+		resume.
+
+What:		/sys/class/usb_power_delivery/.../<capability>/1:fixed_supply/unconstrained_power
+Date:		May 2022
+Contact:	Heikki Krogerus <heikki.krogerus@linux.intel.com>
+Description:
+		This file shows the value of the Unconstrained Power bit in
+		vSafe5V Fixed Supply Object. The bit is set when an external
+		source of power, powerful enough to power the entire system on
+		its own, is available for the device.
+
+What:		/sys/class/usb_power_delivery/.../<capability>/1:fixed_supply/usb_communication_capable
+Date:		May 2022
+Contact:	Heikki Krogerus <heikki.krogerus@linux.intel.com>
+Description:
+		This file shows the value of the USB Communication Capable bit in
+		vSafe5V Fixed Supply Object.
+
+What:		/sys/class/usb_power_delivery/.../<capability>/1:fixed_supply/dual_role_data
+Date:		May 2022
+Contact:	Heikki Krogerus <heikki.krogerus@linux.intel.com>
+Description:
+		This file shows the value of the Dual-Role Data bit in vSafe5V
+		Fixed Supply Object. Dual role data means ability act as both
+		USB host and USB device.
+
+What:		/sys/class/usb_power_delivery/.../<capability>/1:fixed_supply/unchunked_extended_messages_supported
+Date:		May 2022
+Contact:	Heikki Krogerus <heikki.krogerus@linux.intel.com>
+Description:
+		This file shows the value of the Unchunked Extended Messages
+		Supported bit in vSafe5V Fixed Supply Object.
+
+What:		/sys/class/usb_power_delivery/.../<capability>/<position>:fixed_supply/voltage
+Date:		May 2022
+Contact:	Heikki Krogerus <heikki.krogerus@linux.intel.com>
+Description:
+		The voltage the supply supports in millivolts.
+
+What:		/sys/class/usb_power_delivery/.../source-capabilities/<position>:fixed_supply/maximum_current
+Date:		May 2022
+Contact:	Heikki Krogerus <heikki.krogerus@linux.intel.com>
+Description:
+		Maximum current of the fixed source supply in milliamperes.
+
+What:		/sys/class/usb_power_delivery/.../sink-capabilities/<position>:fixed_supply/operational_current
+Date:		May 2022
+Contact:	Heikki Krogerus <heikki.krogerus@linux.intel.com>
+Description:
+		Operational current of the sink in milliamperes.
+
+What:		/sys/class/usb_power_delivery/.../sink-capabilities/<position>:fixed_supply/fast_role_swap_current
+Date:		May 2022
+Contact:	Heikki Krogerus <heikki.krogerus@linux.intel.com>
+Description:
+		This file contains the value of the "Fast Role Swap USB Type-C
+		Current" field that tells the current level the sink requires
+		after a Fast Role Swap.
+		0 - Fast Swap not supported"
+		1 - Default USB Power"
+		2 - 1.5A@5V"
+		3 - 3.0A@5V"
+
+Variable Supplies
+
+What:		/sys/class/usb_power_delivery/.../<capability>/<position>:variable_supply
+Date:		May 2022
+Contact:	Heikki Krogerus <heikki.krogerus@linux.intel.com>
+Description:
+		Variable Power Supply PDO.
+
+What:		/sys/class/usb_power_delivery/.../<capability>/<position>:variable_supply/maximum_voltage
+Date:		May 2022
+Contact:	Heikki Krogerus <heikki.krogerus@linux.intel.com>
+Description:
+		Maximum Voltage in millivolts.
+
+What:		/sys/class/usb_power_delivery/.../<capability>/<position>:variable_supply/minimum_voltage
+Date:		May 2022
+Contact:	Heikki Krogerus <heikki.krogerus@linux.intel.com>
+Description:
+		Minimum Voltage in millivolts.
+
+What:		/sys/class/usb_power_delivery/.../source-capabilities/<position>:variable_supply/maximum_current
+Date:		May 2022
+Contact:	Heikki Krogerus <heikki.krogerus@linux.intel.com>
+Description:
+		The maximum current in milliamperes that the source can supply
+		at the given Voltage range.
+
+What:		/sys/class/usb_power_delivery/.../sink-capabilities/<position>:variable_supply/operational_current
+Date:		May 2022
+Contact:	Heikki Krogerus <heikki.krogerus@linux.intel.com>
+Description:
+		The operational current in milliamperes that the sink requires
+		at the given Voltage range.
+
+Battery Supplies
+
+What:		/sys/class/usb_power_delivery/.../<capability>/<position>:battery
+Date:		May 2022
+Contact:	Heikki Krogerus <heikki.krogerus@linux.intel.com>
+Description:
+		Battery PDO.
+
+What:		/sys/class/usb_power_delivery/.../<capability>/<position>:battery/maximum_voltage
+Date:		May 2022
+Contact:	Heikki Krogerus <heikki.krogerus@linux.intel.com>
+Description:
+		Maximum Voltage in millivolts.
+
+What:		/sys/class/usb_power_delivery/.../<capability>/<position>:battery/minimum_voltage
+Date:		May 2022
+Contact:	Heikki Krogerus <heikki.krogerus@linux.intel.com>
+Description:
+		Minimum Voltage in millivolts.
+
+What:		/sys/class/usb_power_delivery/.../source-capabilities/<position>:battery/maximum_power
+Date:		May 2022
+Contact:	Heikki Krogerus <heikki.krogerus@linux.intel.com>
+Description:
+		Maximum allowable Power in milliwatts.
+
+What:		/sys/class/usb_power_delivery/.../sink-capabilities/<position>:battery/operational_power
+Date:		May 2022
+Contact:	Heikki Krogerus <heikki.krogerus@linux.intel.com>
+Description:
+		The operational power that the sink requires at the given
+		voltage range.
+
+Standard Power Range (SPR) Programmable Power Supplies
+
+What:		/sys/class/usb_power_delivery/.../<capability>/<position>:programmable_supply
+Date:		May 2022
+Contact:	Heikki Krogerus <heikki.krogerus@linux.intel.com>
+Description:
+		Programmable Power Supply (PPS) Augmented PDO (APDO).
+
+What:		/sys/class/usb_power_delivery/.../<capability>/<position>:programmable_supply/maximum_voltage
+Date:		May 2022
+Contact:	Heikki Krogerus <heikki.krogerus@linux.intel.com>
+Description:
+		Maximum Voltage in millivolts.
+
+What:		/sys/class/usb_power_delivery/.../<capability>/<position>:programmable_supply/minimum_voltage
+Date:		May 2022
+Contact:	Heikki Krogerus <heikki.krogerus@linux.intel.com>
+Description:
+		Minimum Voltage in millivolts.
+
+What:		/sys/class/usb_power_delivery/.../<capability>/<position>:programmable_supply/maximum_current
+Date:		May 2022
+Contact:	Heikki Krogerus <heikki.krogerus@linux.intel.com>
+Description:
+		Maximum Current in milliamperes.
+
+What:		/sys/class/usb_power_delivery/.../source-capabilities/<position>:programmable_supply/pps_power_limited
+Date:		May 2022
+Contact:	Heikki Krogerus <heikki.krogerus@linux.intel.com>
+Description:
+		The PPS Power Limited bit indicates whether or not the source
+		supply will exceed the rated output power if requested.
diff --git a/Documentation/devicetree/bindings/usb/analogix,anx7411.yaml b/Documentation/devicetree/bindings/usb/analogix,anx7411.yaml
new file mode 100644
index 000000000000..ee436308e5dc
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/analogix,anx7411.yaml
@@ -0,0 +1,81 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/usb/analogix,anx7411.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Analogix ANX7411 Type-C controller bindings
+
+maintainers:
+  - Xin Ji <xji@analogixsemi.com>
+
+properties:
+  compatible:
+    enum:
+      - analogix,anx7411
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  connector:
+    type: object
+    $ref: ../connector/usb-connector.yaml
+    description:
+      Properties for usb c connector.
+
+    properties:
+      compatible:
+        const: usb-c-connector
+
+      power-role: true
+
+      data-role: true
+
+      try-power-role: true
+
+    required:
+      - compatible
+
+required:
+  - compatible
+  - reg
+  - connector
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        typec@2c {
+            compatible = "analogix,anx7411";
+            reg = <0x2c>;
+            interrupts = <8 IRQ_TYPE_EDGE_FALLING>;
+            interrupt-parent = <&gpio0>;
+
+            typec_con: connector {
+                compatible = "usb-c-connector";
+                power-role = "dual";
+                data-role = "dual";
+                try-power-role = "source";
+
+                ports {
+                    #address-cells = <1>;
+                    #size-cells = <0>;
+                    port@0 {
+                        reg = <0>;
+                        typec_con_ep: endpoint {
+                            remote-endpoint = <&usbotg_hs_ep>;
+                        };
+                    };
+                };
+            };
+        };
+    };
+...
diff --git a/Documentation/devicetree/bindings/usb/aspeed,ast2600-udc.yaml b/Documentation/devicetree/bindings/usb/aspeed,ast2600-udc.yaml
new file mode 100644
index 000000000000..c3b6be3d8002
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/aspeed,ast2600-udc.yaml
@@ -0,0 +1,52 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (c) 2020 Facebook Inc.
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/usb/aspeed,ast2600-udc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ASPEED USB 2.0 Device Controller
+
+maintainers:
+  - Neal Liu <neal_liu@aspeedtech.com>
+
+description: |+
+  The ASPEED USB 2.0 Device Controller implements 1 control endpoint and
+  4 generic endpoints for AST260x.
+
+  Supports independent DMA channel for each generic endpoint.
+  Supports 32/256 stages descriptor mode for all generic endpoints.
+
+properties:
+  compatible:
+    enum:
+      - aspeed,ast2600-udc
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/aspeed-clock.h>
+    udc: usb@1e6a2000 {
+        compatible = "aspeed,ast2600-udc";
+        reg = <0x1e6a2000 0x300>;
+        interrupts = <9>;
+        clocks = <&syscon ASPEED_CLK_GATE_USBPORT2CLK>;
+        pinctrl-names = "default";
+        pinctrl-0 = <&pinctrl_usb2bd_default>;
+    };
diff --git a/Documentation/devicetree/bindings/usb/dwc2.yaml b/Documentation/devicetree/bindings/usb/dwc2.yaml
index 8d22a9843ba5..1bfbc6ef16eb 100644
--- a/Documentation/devicetree/bindings/usb/dwc2.yaml
+++ b/Documentation/devicetree/bindings/usb/dwc2.yaml
@@ -11,6 +11,7 @@ maintainers:
 
 allOf:
   - $ref: usb-drd.yaml#
+  - $ref: usb-hcd.yaml#
 
 properties:
   compatible:
@@ -161,6 +162,8 @@ properties:
       property is used.
     $ref: /schemas/graph.yaml#/properties/port
 
+  tpl-support: true
+
 dependencies:
   port: [ usb-role-switch ]
   role-switch-default-mode: [ usb-role-switch ]
diff --git a/Documentation/devicetree/bindings/usb/generic-ehci.yaml b/Documentation/devicetree/bindings/usb/generic-ehci.yaml
index 25a6c14618e1..079f7cff0c24 100644
--- a/Documentation/devicetree/bindings/usb/generic-ehci.yaml
+++ b/Documentation/devicetree/bindings/usb/generic-ehci.yaml
@@ -131,11 +131,6 @@ properties:
       Set this flag to indicate that the hardware sometimes turns on
       the OC bit when an over-current isn't actually present.
 
-  companion:
-    $ref: /schemas/types.yaml#/definitions/phandle
-    description:
-      Phandle of a companion.
-
   phys:
     minItems: 1
     maxItems: 3
@@ -156,7 +151,7 @@ required:
   - reg
   - interrupts
 
-additionalProperties: false
+unevaluatedProperties: false
 
 examples:
   - |
diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
index 084d7135b2d9..b0e58b15b9ae 100644
--- a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
+++ b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
@@ -31,6 +31,7 @@ properties:
           - mediatek,mt8173-xhci
           - mediatek,mt8183-xhci
           - mediatek,mt8186-xhci
+          - mediatek,mt8188-xhci
           - mediatek,mt8192-xhci
           - mediatek,mt8195-xhci
       - const: mediatek,mtk-xhci
@@ -57,6 +58,7 @@ properties:
       - description: optional, wakeup interrupt used to support runtime PM
 
   interrupt-names:
+    minItems: 1
     items:
       - const: host
       - const: wakeup
@@ -113,6 +115,9 @@ properties:
   vbus-supply:
     description: Regulator of USB VBUS5v
 
+  resets:
+    maxItems: 1
+
   usb3-lpm-capable: true
 
   usb2-lpm-disable: true
diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml b/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml
index 37b02a841dc4..e63b66545317 100644
--- a/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml
+++ b/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml
@@ -107,6 +107,9 @@ properties:
   maximum-speed:
     enum: [super-speed-plus, super-speed, high-speed, full-speed]
 
+  resets:
+    maxItems: 1
+
   "#address-cells":
     enum: [1, 2]
 
diff --git a/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml b/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml
index 749e1963ddbb..fea3e7092ace 100644
--- a/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml
+++ b/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml
@@ -24,6 +24,7 @@ properties:
           - qcom,qcs404-dwc3
           - qcom,sc7180-dwc3
           - qcom,sc7280-dwc3
+          - qcom,sc8280xp-dwc3
           - qcom,sdm660-dwc3
           - qcom,sdm845-dwc3
           - qcom,sdx55-dwc3
@@ -66,11 +67,11 @@ properties:
        - mock_utmi:: Mock utmi clock needed for ITP/SOF generation in host
                      mode. Its frequency should be 19.2MHz.
     minItems: 1
-    maxItems: 6
+    maxItems: 9
 
   clock-names:
     minItems: 1
-    maxItems: 6
+    maxItems: 9
 
   assigned-clocks:
     items:
@@ -93,20 +94,12 @@ properties:
       - const: apps-usb
 
   interrupts:
-    items:
-      - description: The interrupt that is asserted
-          when a wakeup event is received on USB2 bus.
-      - description: The interrupt that is asserted
-          when a wakeup event is received on USB3 bus.
-      - description: Wakeup event on DM line.
-      - description: Wakeup event on DP line.
+    minItems: 1
+    maxItems: 4
 
   interrupt-names:
-    items:
-      - const: hs_phy_irq
-      - const: ss_phy_irq
-      - const: dm_hs_phy_irq
-      - const: dp_hs_phy_irq
+    minItems: 1
+    maxItems: 4
 
   qcom,select-utmi-as-pipe-clk:
     description:
@@ -254,6 +247,28 @@ allOf:
         compatible:
           contains:
             enum:
+              - qcom,sc8280xp-dwc3
+    then:
+      properties:
+        clocks:
+          maxItems: 9
+        clock-names:
+          items:
+            - const: cfg_noc
+            - const: core
+            - const: iface
+            - const: sleep
+            - const: mock_utmi
+            - const: noc_aggr
+            - const: noc_aggr_north
+            - const: noc_aggr_south
+            - const: noc_sys
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
               - qcom,sdm660-dwc3
     then:
       properties:
@@ -311,6 +326,115 @@ allOf:
             - const: mock_utmi
             - const: xo
 
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,ipq4019-dwc3
+              - qcom,ipq6018-dwc3
+              - qcom,ipq8064-dwc3
+              - qcom,ipq8074-dwc3
+              - qcom,msm8994-dwc3
+              - qcom,qcs404-dwc3
+              - qcom,sc7180-dwc3
+              - qcom,sdm845-dwc3
+              - qcom,sdx55-dwc3
+              - qcom,sdx65-dwc3
+              - qcom,sm4250-dwc3
+              - qcom,sm6115-dwc3
+              - qcom,sm6125-dwc3
+              - qcom,sm6350-dwc3
+              - qcom,sm8150-dwc3
+              - qcom,sm8250-dwc3
+              - qcom,sm8350-dwc3
+              - qcom,sm8450-dwc3
+    then:
+      properties:
+        interrupts:
+          items:
+            - description: The interrupt that is asserted
+                when a wakeup event is received on USB2 bus.
+            - description: The interrupt that is asserted
+                when a wakeup event is received on USB3 bus.
+            - description: Wakeup event on DM line.
+            - description: Wakeup event on DP line.
+        interrupt-names:
+          items:
+            - const: hs_phy_irq
+            - const: ss_phy_irq
+            - const: dm_hs_phy_irq
+            - const: dp_hs_phy_irq
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,msm8953-dwc3
+              - qcom,msm8996-dwc3
+              - qcom,msm8998-dwc3
+    then:
+      properties:
+        interrupts:
+          maxItems: 2
+        interrupt-names:
+          items:
+            - const: hs_phy_irq
+            - const: ss_phy_irq
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,sdm660-dwc3
+    then:
+      properties:
+        interrupts:
+          minItems: 1
+          maxItems: 2
+        interrupt-names:
+          minItems: 1
+          items:
+            - const: hs_phy_irq
+            - const: ss_phy_irq
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,sc7280-dwc3
+    then:
+      properties:
+        interrupts:
+          minItems: 3
+          maxItems: 4
+        interrupt-names:
+          minItems: 3
+          items:
+            - const: hs_phy_irq
+            - const: dp_hs_phy_irq
+            - const: dm_hs_phy_irq
+            - const: ss_phy_irq
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,sc8280xp-dwc3
+    then:
+      properties:
+        interrupts:
+          maxItems: 4
+        interrupt-names:
+          items:
+            - const: pwr_event
+            - const: dp_hs_phy_irq
+            - const: dm_hs_phy_irq
+            - const: ss_phy_irq
 
 additionalProperties: false
 
diff --git a/Documentation/devicetree/bindings/usb/realtek,rts5411.yaml b/Documentation/devicetree/bindings/usb/realtek,rts5411.yaml
index 04ee255eb4f0..50f2b505bdeb 100644
--- a/Documentation/devicetree/bindings/usb/realtek,rts5411.yaml
+++ b/Documentation/devicetree/bindings/usb/realtek,rts5411.yaml
@@ -25,13 +25,13 @@ properties:
     description:
       phandle to the regulator that provides power to the hub.
 
-  companion-hub:
+  peer-hub:
     $ref: '/schemas/types.yaml#/definitions/phandle'
     description:
-      phandle to the companion hub on the controller.
+      phandle to the peer hub on the controller.
 
 required:
-  - companion-hub
+  - peer-hub
   - compatible
   - reg
 
@@ -49,7 +49,7 @@ examples:
             compatible = "usbbda,5411";
             reg = <1>;
             vdd-supply = <&pp3300_hub>;
-            companion-hub = <&hub_3_0>;
+            peer-hub = <&hub_3_0>;
         };
 
         /* 3.0 hub on port 2 */
@@ -57,6 +57,6 @@ examples:
             compatible = "usbbda,411";
             reg = <2>;
             vdd-supply = <&pp3300_hub>;
-            companion-hub = <&hub_2_0>;
+            peer-hub = <&hub_2_0>;
         };
     };
diff --git a/Documentation/devicetree/bindings/usb/snps,dwc3.yaml b/Documentation/devicetree/bindings/usb/snps,dwc3.yaml
index d41265ba8ce2..1779d08ba1c0 100644
--- a/Documentation/devicetree/bindings/usb/snps,dwc3.yaml
+++ b/Documentation/devicetree/bindings/usb/snps,dwc3.yaml
@@ -343,6 +343,11 @@ properties:
       This port is used with the 'usb-role-switch' property  to connect the
       dwc3 to type C connector.
 
+  wakeup-source:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      Enable USB remote wakeup.
+
 unevaluatedProperties: false
 
 required:
diff --git a/Documentation/devicetree/bindings/usb/st,typec-stm32g0.yaml b/Documentation/devicetree/bindings/usb/st,typec-stm32g0.yaml
new file mode 100644
index 000000000000..1cb68cabe17d
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/st,typec-stm32g0.yaml
@@ -0,0 +1,91 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/usb/st,typec-stm32g0.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: STMicroelectronics STM32G0 USB Type-C PD controller
+
+description: |
+  The STM32G0 MCU can be programmed to control Type-C connector(s) through I2C
+  typically using the UCSI protocol over I2C, with a dedicated alert
+  (interrupt) pin.
+
+maintainers:
+  - Fabrice Gasnier <fabrice.gasnier@foss.st.com>
+
+properties:
+  compatible:
+    const: st,stm32g0-typec
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  connector:
+    type: object
+    $ref: /schemas/connector/usb-connector.yaml#
+    unevaluatedProperties: false
+
+  firmware-name:
+    description: |
+      Should contain the name of the default firmware image
+      file located on the firmware search path
+
+  wakeup-source: true
+
+  power-domains:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - connector
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      typec@53 {
+        compatible = "st,stm32g0-typec";
+        reg = <0x53>;
+        /* Alert pin on GPIO PE12 */
+        interrupts = <12 IRQ_TYPE_EDGE_FALLING>;
+        interrupt-parent = <&gpioe>;
+
+        /* Example with one type-C connector */
+        connector {
+          compatible = "usb-c-connector";
+          label = "USB-C";
+
+          ports {
+            #address-cells = <1>;
+            #size-cells = <0>;
+            port@0 {
+              reg = <0>;
+              con_usb_c_ep: endpoint {
+                remote-endpoint = <&usb_ep>;
+              };
+            };
+          };
+        };
+      };
+    };
+
+    usb {
+      usb-role-switch;
+      port {
+        usb_ep: endpoint {
+          remote-endpoint = <&con_usb_c_ep>;
+        };
+      };
+    };
+...
diff --git a/Documentation/devicetree/bindings/usb/ti,usb8041.yaml b/Documentation/devicetree/bindings/usb/ti,usb8041.yaml
new file mode 100644
index 000000000000..e04fbd8ab0b7
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/ti,usb8041.yaml
@@ -0,0 +1,67 @@
+# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/usb/ti,usb8041.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Binding for the TI USB8041 USB 3.0 hub controller
+
+maintainers:
+  - Alexander Stein <alexander.stein@ew.tq-group.com>
+
+allOf:
+  - $ref: usb-device.yaml#
+
+properties:
+  compatible:
+    enum:
+      - usb451,8140
+      - usb451,8142
+
+  reg: true
+
+  reset-gpios:
+    items:
+      - description: GPIO specifier for GRST# pin.
+
+  vdd-supply:
+    description:
+      VDD power supply to the hub
+
+  peer-hub:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description:
+      phandle to the peer hub on the controller.
+
+required:
+  - compatible
+  - reg
+  - peer-hub
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    usb {
+        dr_mode = "host";
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        /* 2.0 hub on port 1 */
+        hub_2_0: hub@1 {
+          compatible = "usb451,8142";
+          reg = <1>;
+          peer-hub = <&hub_3_0>;
+          reset-gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
+        };
+
+        /* 3.0 hub on port 2 */
+        hub_3_0: hub@2 {
+          compatible = "usb451,8140";
+          reg = <2>;
+          peer-hub = <&hub_2_0>;
+          reset-gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
+        };
+    };
diff --git a/Documentation/usb/gadget-testing.rst b/Documentation/usb/gadget-testing.rst
index 1c37159fa171..2278c9ffb74a 100644
--- a/Documentation/usb/gadget-testing.rst
+++ b/Documentation/usb/gadget-testing.rst
@@ -333,6 +333,12 @@ In each lun directory there are the following attribute files:
 			being a CD-ROM.
 	nofua		Flag specifying that FUA flag
 			in SCSI WRITE(10,12)
+	forced_eject	This write-only file is useful only when
+			the function is active. It causes the backing
+			file to be forcibly detached from the LUN,
+			regardless of whether the host has allowed it.
+			Any non-zero number of bytes written will
+			result in ejection.
 	=============== ==============================================
 
 Testing the MASS STORAGE function
diff --git a/Documentation/usb/mass-storage.rst b/Documentation/usb/mass-storage.rst
index d181b47c3cb6..f399ec631599 100644
--- a/Documentation/usb/mass-storage.rst
+++ b/Documentation/usb/mass-storage.rst
@@ -181,6 +181,15 @@ sysfs entries
     Reflects the state of nofua flag for given logical unit.  It can
     be read and written.
 
+  - forced_eject
+
+    When written into, it causes the backing file to be forcibly
+    detached from the LUN, regardless of whether the host has allowed
+    it.  The content doesn't matter, any non-zero number of bytes
+    written will result in ejection.
+
+    Can not be read.
+
   Other then those, as usual, the values of module parameters can be
   read from /sys/module/g_mass_storage/parameters/* files.