summaryrefslogtreecommitdiffstats
path: root/Documentation
diff options
context:
space:
mode:
authorLinus Torvalds <torvalds@linux-foundation.org>2016-01-20 18:42:30 -0800
committerLinus Torvalds <torvalds@linux-foundation.org>2016-01-20 18:42:30 -0800
commit9638685e32af961943b679fcb72d4ddd458eb18f (patch)
tree83cea0db18256448e2eaa9aec3bdbd3b89f26646 /Documentation
parent03d7d12415e3a4791994e566f1245838bc505c6b (diff)
parentce96cb7386a57b270648f9ba6003065329a26bd3 (diff)
downloadlinux-9638685e32af961943b679fcb72d4ddd458eb18f.tar.bz2
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson: "Driver updates for ARM SoCs. Some for SoC-family code under drivers/soc, but also some other driver updates that don't belong anywhere else. We also bring in the drivers/reset code through arm-soc. Some of the larger updates: - Qualcomm support for SMEM, SMSM, SMP2P. All used to communicate with other parts of the chip/board on these platforms, all proprietary protocols that don't fit into other subsystems and live in drivers/soc for now. - System bus driver for UniPhier - Driver for the TI Wakeup M3 IPC device - Power management for Raspberry PI + Again a bunch of other smaller updates and patches" * tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits) bus: uniphier: allow only built-in driver ARM: bcm2835: clarify RASPBERRYPI_FIRMWARE dependency MAINTAINERS: Drop Kumar Gala from QCOM bus: uniphier-system-bus: add UniPhier System Bus driver ARM: bcm2835: add rpi power domain driver dt-bindings: add rpi power domain driver bindings ARM: bcm2835: Define two new packets from the latest firmware. drivers/soc: make mediatek/mtk-scpsys.c explicitly non-modular soc: mediatek: SCPSYS: Add regulator support MAINTAINERS: Change QCOM entries soc: qcom: smd-rpm: Add existing platform support memory/tegra: Add number of TLB lines for Tegra124 reset: hi6220: fix modular build soc: qcom: Introduce WCNSS_CTRL SMD client ARM: qcom: select ARM_CPU_SUSPEND for power management MAINTAINERS: Add rules for Qualcomm dts files soc: qcom: enable smsm/smp2p modular build serial: msm_serial: Make config tristate soc: qcom: smp2p: Qualcomm Shared Memory Point to Point soc: qcom: smsm: Add driver for Qualcomm SMSM ...
Diffstat (limited to 'Documentation')
-rw-r--r--Documentation/devicetree/bindings/bus/uniphier-system-bus.txt66
-rw-r--r--Documentation/devicetree/bindings/reset/hisilicon,hi6220-reset.txt34
-rw-r--r--Documentation/devicetree/bindings/soc/bcm/raspberrypi,bcm2835-power.txt47
-rw-r--r--Documentation/devicetree/bindings/soc/ti/wkup_m3_ipc.txt57
4 files changed, 204 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/bus/uniphier-system-bus.txt b/Documentation/devicetree/bindings/bus/uniphier-system-bus.txt
new file mode 100644
index 000000000000..68ef80afff16
--- /dev/null
+++ b/Documentation/devicetree/bindings/bus/uniphier-system-bus.txt
@@ -0,0 +1,66 @@
+UniPhier System Bus
+
+The UniPhier System Bus is an external bus that connects on-board devices to
+the UniPhier SoC. It is a simple (semi-)parallel bus with address, data, and
+some control signals. It supports up to 8 banks (chip selects).
+
+Before any access to the bus, the bus controller must be configured; the bus
+controller registers provide the control for the translation from the offset
+within each bank to the CPU-viewed address. The needed setup includes the base
+address, the size of each bank. Optionally, some timing parameters can be
+optimized for faster bus access.
+
+Required properties:
+- compatible: should be "socionext,uniphier-system-bus".
+- reg: offset and length of the register set for the bus controller device.
+- #address-cells: should be 2. The first cell is the bank number (chip select).
+ The second cell is the address offset within the bank.
+- #size-cells: should be 1.
+- ranges: should provide a proper address translation from the System Bus to
+ the parent bus.
+
+Note:
+The address region(s) that can be assigned for the System Bus is implementation
+defined. Some SoCs can use 0x00000000-0x0fffffff and 0x40000000-0x4fffffff,
+while other SoCs can only use 0x40000000-0x4fffffff. There might be additional
+limitations depending on SoCs and the boot mode. The address translation is
+arbitrary as long as the banks are assigned in the supported address space with
+the required alignment and they do not overlap one another.
+For example, it is possible to map:
+ bank 0 to 0x42000000-0x43ffffff, bank 5 to 0x46000000-0x46ffffff
+It is also possible to map:
+ bank 0 to 0x48000000-0x49ffffff, bank 5 to 0x44000000-0x44ffffff
+There is no reason to stick to a particular translation mapping, but the
+"ranges" property should provide a "reasonable" default that is known to work.
+The software should initialize the bus controller according to it.
+
+Example:
+
+ system-bus {
+ compatible = "socionext,uniphier-system-bus";
+ reg = <0x58c00000 0x400>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges = <1 0x00000000 0x42000000 0x02000000
+ 5 0x00000000 0x46000000 0x01000000>;
+
+ ethernet@1,01f00000 {
+ compatible = "smsc,lan9115";
+ reg = <1 0x01f00000 0x1000>;
+ interrupts = <0 48 4>
+ phy-mode = "mii";
+ };
+
+ uart@5,00200000 {
+ compatible = "ns16550a";
+ reg = <5 0x00200000 0x20>;
+ interrupts = <0 49 4>
+ clock-frequency = <12288000>;
+ };
+ };
+
+In this example,
+ - the Ethernet device is connected at the offset 0x01f00000 of CS1 and
+ mapped to 0x43f00000 of the parent bus.
+ - the UART device is connected at the offset 0x00200000 of CS5 and
+ mapped to 0x46200000 of the parent bus.
diff --git a/Documentation/devicetree/bindings/reset/hisilicon,hi6220-reset.txt b/Documentation/devicetree/bindings/reset/hisilicon,hi6220-reset.txt
new file mode 100644
index 000000000000..e0b185a944ba
--- /dev/null
+++ b/Documentation/devicetree/bindings/reset/hisilicon,hi6220-reset.txt
@@ -0,0 +1,34 @@
+Hisilicon System Reset Controller
+======================================
+
+Please also refer to reset.txt in this directory for common reset
+controller binding usage.
+
+The reset controller registers are part of the system-ctl block on
+hi6220 SoC.
+
+Required properties:
+- compatible: may be "hisilicon,hi6220-sysctrl"
+- reg: should be register base and length as documented in the
+ datasheet
+- #reset-cells: 1, see below
+
+Example:
+sys_ctrl: sys_ctrl@f7030000 {
+ compatible = "hisilicon,hi6220-sysctrl", "syscon";
+ reg = <0x0 0xf7030000 0x0 0x2000>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+};
+
+Specifying reset lines connected to IP modules
+==============================================
+example:
+
+ uart1: serial@..... {
+ ...
+ resets = <&sys_ctrl PERIPH_RSTEN3_UART1>;
+ ...
+ };
+
+The index could be found in <dt-bindings/reset/hisi,hi6220-resets.h>.
diff --git a/Documentation/devicetree/bindings/soc/bcm/raspberrypi,bcm2835-power.txt b/Documentation/devicetree/bindings/soc/bcm/raspberrypi,bcm2835-power.txt
new file mode 100644
index 000000000000..30942cf7992b
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/bcm/raspberrypi,bcm2835-power.txt
@@ -0,0 +1,47 @@
+Raspberry Pi power domain driver
+
+Required properties:
+
+- compatible: Should be "raspberrypi,bcm2835-power".
+- firmware: Reference to the RPi firmware device node.
+- #power-domain-cells: Should be <1>, we providing multiple power domains.
+
+The valid defines for power domain are:
+
+ RPI_POWER_DOMAIN_I2C0
+ RPI_POWER_DOMAIN_I2C1
+ RPI_POWER_DOMAIN_I2C2
+ RPI_POWER_DOMAIN_VIDEO_SCALER
+ RPI_POWER_DOMAIN_VPU1
+ RPI_POWER_DOMAIN_HDMI
+ RPI_POWER_DOMAIN_USB
+ RPI_POWER_DOMAIN_VEC
+ RPI_POWER_DOMAIN_JPEG
+ RPI_POWER_DOMAIN_H264
+ RPI_POWER_DOMAIN_V3D
+ RPI_POWER_DOMAIN_ISP
+ RPI_POWER_DOMAIN_UNICAM0
+ RPI_POWER_DOMAIN_UNICAM1
+ RPI_POWER_DOMAIN_CCP2RX
+ RPI_POWER_DOMAIN_CSI2
+ RPI_POWER_DOMAIN_CPI
+ RPI_POWER_DOMAIN_DSI0
+ RPI_POWER_DOMAIN_DSI1
+ RPI_POWER_DOMAIN_TRANSPOSER
+ RPI_POWER_DOMAIN_CCP2TX
+ RPI_POWER_DOMAIN_CDP
+ RPI_POWER_DOMAIN_ARM
+
+Example:
+
+power: power {
+ compatible = "raspberrypi,bcm2835-power";
+ firmware = <&firmware>;
+ #power-domain-cells = <1>;
+};
+
+Example for using power domain:
+
+&usb {
+ power-domains = <&power RPI_POWER_DOMAIN_USB>;
+};
diff --git a/Documentation/devicetree/bindings/soc/ti/wkup_m3_ipc.txt b/Documentation/devicetree/bindings/soc/ti/wkup_m3_ipc.txt
new file mode 100644
index 000000000000..401550487ed6
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/ti/wkup_m3_ipc.txt
@@ -0,0 +1,57 @@
+Wakeup M3 IPC Driver
+=====================
+
+The TI AM33xx and AM43xx family of devices use a small Cortex M3 co-processor
+(commonly referred to as Wakeup M3 or CM3) to help with various low power tasks
+that cannot be controlled from the MPU, like suspend/resume and certain deep
+C-states for CPU Idle. Once the wkup_m3_ipc driver uses the wkup_m3_rproc driver
+to boot the wkup_m3, it handles communication with the CM3 using IPC registers
+present in the SoC's control module and a mailbox. The wkup_m3_ipc exposes an
+API to allow the SoC PM code to execute specific PM tasks.
+
+Wkup M3 Device Node:
+====================
+A wkup_m3_ipc device node is used to represent the IPC registers within an
+SoC.
+
+Required properties:
+--------------------
+- compatible: Should be,
+ "ti,am3352-wkup-m3-ipc" for AM33xx SoCs
+ "ti,am4372-wkup-m3-ipc" for AM43xx SoCs
+- reg: Contains the IPC register address space to communicate
+ with the Wakeup M3 processor
+- interrupts: Contains the interrupt information for the wkup_m3
+ interrupt that signals the MPU.
+- ti,rproc: phandle to the wkup_m3 rproc node so the IPC driver
+ can boot it.
+- mboxes: phandles used by IPC framework to get correct mbox
+ channel for communication. Must point to appropriate
+ mbox_wkupm3 child node.
+
+Example:
+--------
+/* AM33xx */
+ l4_wkup: l4_wkup@44c00000 {
+ ...
+
+ scm: scm@210000 {
+ compatible = "ti,am3-scm", "simple-bus";
+ reg = <0x210000 0x2000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x210000 0x2000>;
+
+ ...
+
+ wkup_m3_ipc: wkup_m3_ipc@1324 {
+ compatible = "ti,am3352-wkup-m3-ipc";
+ reg = <0x1324 0x24>;
+ interrupts = <78>;
+ ti,rproc = <&wkup_m3>;
+ mboxes = <&mailbox &mbox_wkupm3>;
+ };
+
+ ...
+ };
+ };