sound: Retire OSS

Since no complaints have been raised after disabling the build of OSS
(Open Sound System) by the commit 31cbee6a5611 ("sound: Disable the
build of OSS drivers"), let's finally drop the whole code and
documentation.

Some glue codes are still left intact since sound/oss/dmasound stuff
remains -- which is an independent implementation solely for m68k, and
it's not covered by ALSA yet.

Also, a couple of API header files (linux/sound.h and
linux/soundcard.h) are kept remaining as well, since the OSS API
itself is still supported by ALSA OSS emulation, and applications can
refer to these.

Where we're at it, some help texts in the top-level Kconfig are
adjusted, too (who still needs to specify I/O port in kbuild
nowadays?).

Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

1 files changed, 0 insertions, 55 deletions

diff --git a/Documentation/sound/oss/ESS1868 b/Documentation/sound/oss/ESS1868
deleted file mode 100644
index 55e922f21bc0..000000000000
--- a/Documentation/sound/oss/ESS1868
+++ /dev/null
@@ -1,55 +0,0 @@
-Documentation for the ESS1868F AudioDrive PnP sound card
-
-The ESS1868 sound card is a PnP ESS1688-compatible 16-bit sound card.
-
-It should be automatically detected by the Linux Kernel isapnp support when you
-load the sb.o module. Otherwise you should take care of:
-
-  *  The ESS1868 does not allow use of a 16-bit DMA, thus DMA 0, 1, 2, and 3
-     may only be used.
-
-  *  isapnptools version 1.14 does work with ESS1868.  Earlier versions might
-     not.
-
-  *  Sound support MUST be compiled as MODULES, not statically linked
-     into the kernel.
-
-
-NOTE: this is only needed when not using the kernel isapnp support!
-
-For configuring the sound card's I/O addresses, IRQ and DMA, here is a
-sample copy of the isapnp.conf directives regarding the ESS1868:
-
-(CONFIGURE ESS1868/-1 (LD 1
-(IO 0 (BASE 0x0220))
-(IO 1 (BASE 0x0388))
-(IO 2 (BASE 0x0330))
-(DMA 0 (CHANNEL 1))
-(INT 0 (IRQ 5 (MODE +E)))
-(ACT Y)
-))
-
-(for a full working isapnp.conf file, remember the
-(ISOLATE)
-(IDENTIFY *)
-at the beginning and the
-(WAITFORKEY)
-at the end.)
-
-In this setup, the main card I/O is 0x0220, FM synthesizer is 0x0388, and
-the MPU-401 MIDI port is located at 0x0330.  IRQ is IRQ 5, DMA is channel 1.
-
-After configuring the sound card via isapnp, to use the card you must load
-the sound modules with the proper I/O information.  Here is my setup:
-
-# ESS1868F AudioDrive initialization
-
-/sbin/modprobe sound
-/sbin/insmod uart401
-/sbin/insmod sb io=0x220 irq=5 dma=1 dma16=-1
-/sbin/insmod mpu401 io=0x330
-/sbin/insmod opl3 io=0x388
-/sbin/insmod v_midi
-
-opl3 is the FM synthesizer
-/sbin/insmod opl3 io=0x388