docs: networking: move FDDI drivers to the hw driver section

Move docs for defza and skfp under device_drivers/fddi.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

1 files changed, 0 insertions, 253 deletions

diff --git a/Documentation/networking/skfp.rst b/Documentation/networking/skfp.rst
deleted file mode 100644
index 58f548105c1d..000000000000
--- a/Documentation/networking/skfp.rst
+++ /dev/null
@@ -1,253 +0,0 @@
-.. SPDX-License-Identifier: GPL-2.0
-
-.. include:: <isonum.txt>
-
-========================
-SysKonnect driver - SKFP
-========================
-
-|copy| Copyright 1998-2000 SysKonnect,
-
-skfp.txt created 11-May-2000
-
-Readme File for skfp.o v2.06
-
-
-.. This file contains
-
-   (1) OVERVIEW
-   (2) SUPPORTED ADAPTERS
-   (3) GENERAL INFORMATION
-   (4) INSTALLATION
-   (5) INCLUSION OF THE ADAPTER IN SYSTEM START
-   (6) TROUBLESHOOTING
-   (7) FUNCTION OF THE ADAPTER LEDS
-   (8) HISTORY
-
-
-1. Overview
-===========
-
-This README explains how to use the driver 'skfp' for Linux with your
-network adapter.
-
-Chapter 2: Contains a list of all network adapters that are supported by
-this driver.
-
-Chapter 3:
-	   Gives some general information.
-
-Chapter 4: Describes common problems and solutions.
-
-Chapter 5: Shows the changed functionality of the adapter LEDs.
-
-Chapter 6: History of development.
-
-
-2. Supported adapters
-=====================
-
-The network driver 'skfp' supports the following network adapters:
-SysKonnect adapters:
-
-  - SK-5521 (SK-NET FDDI-UP)
-  - SK-5522 (SK-NET FDDI-UP DAS)
-  - SK-5541 (SK-NET FDDI-FP)
-  - SK-5543 (SK-NET FDDI-LP)
-  - SK-5544 (SK-NET FDDI-LP DAS)
-  - SK-5821 (SK-NET FDDI-UP64)
-  - SK-5822 (SK-NET FDDI-UP64 DAS)
-  - SK-5841 (SK-NET FDDI-FP64)
-  - SK-5843 (SK-NET FDDI-LP64)
-  - SK-5844 (SK-NET FDDI-LP64 DAS)
-
-Compaq adapters (not tested):
-
-  - Netelligent 100 FDDI DAS Fibre SC
-  - Netelligent 100 FDDI SAS Fibre SC
-  - Netelligent 100 FDDI DAS UTP
-  - Netelligent 100 FDDI SAS UTP
-  - Netelligent 100 FDDI SAS Fibre MIC
-
-
-3. General Information
-======================
-
-From v2.01 on, the driver is integrated in the linux kernel sources.
-Therefore, the installation is the same as for any other adapter
-supported by the kernel.
-
-Refer to the manual of your distribution about the installation
-of network adapters.
-
-Makes my life much easier :-)
-
-4. Troubleshooting
-==================
-
-If you run into problems during installation, check those items:
-
-Problem:
-	  The FDDI adapter cannot be found by the driver.
-
-Reason:
-	  Look in /proc/pci for the following entry:
-
-	     'FDDI network controller: SysKonnect SK-FDDI-PCI ...'
-
-	  If this entry exists, then the FDDI adapter has been
-	  found by the system and should be able to be used.
-
-	  If this entry does not exist or if the file '/proc/pci'
-	  is not there, then you may have a hardware problem or PCI
-	  support may not be enabled in your kernel.
-
-	  The adapter can be checked using the diagnostic program
-	  which is available from the SysKonnect web site:
-
-	      www.syskonnect.de
-
-	  Some COMPAQ machines have a problem with PCI under
-	  Linux. This is described in the 'PCI howto' document
-	  (included in some distributions or available from the
-	  www, e.g. at 'www.linux.org') and no workaround is available.
-
-Problem:
-	  You want to use your computer as a router between
-	  multiple IP subnetworks (using multiple adapters), but
-	  you cannot reach computers in other subnetworks.
-
-Reason:
-	  Either the router's kernel is not configured for IP
-	  forwarding or there is a problem with the routing table
-	  and gateway configuration in at least one of the
-	  computers.
-
-If your problem is not listed here, please contact our
-technical support for help.
-
-You can send email to: linux@syskonnect.de
-
-When contacting our technical support,
-please ensure that the following information is available:
-
-- System Manufacturer and Model
-- Boards in your system
-- Distribution
-- Kernel version
-
-
-5. Function of the Adapter LEDs
-===============================
-
-	The functionality of the LED's on the FDDI network adapters was
-	changed in SMT version v2.82. With this new SMT version, the yellow
-	LED works as a ring operational indicator. An active yellow LED
-	indicates that the ring is down. The green LED on the adapter now
-	works as a link indicator where an active GREEN LED indicates that
-	the respective port has a physical connection.
-
-	With versions of SMT prior to v2.82 a ring up was indicated if the
-	yellow LED was off while the green LED(s) showed the connection
-	status of the adapter. During a ring down the green LED was off and
-	the yellow LED was on.
-
-	All implementations indicate that a driver is not loaded if
-	all LEDs are off.
-
-
-6. History
-==========
-
-v2.06 (20000511) (In-Kernel version)
-    New features:
-
-	- 64 bit support
-	- new pci dma interface
-	- in kernel 2.3.99
-
-v2.05 (20000217) (In-Kernel version)
-    New features:
-
-	- Changes for 2.3.45 kernel
-
-v2.04 (20000207) (Standalone version)
-    New features:
-
-	- Added rx/tx byte counter
-
-v2.03 (20000111) (Standalone version)
-    Problems fixed:
-
-	- Fixed printk statements from v2.02
-
-v2.02 (991215) (Standalone version)
-    Problems fixed:
-
-	- Removed unnecessary output
-	- Fixed path for "printver.sh" in makefile
-
-v2.01 (991122) (In-Kernel version)
-    New features:
-
-	- Integration in Linux kernel sources
-	- Support for memory mapped I/O.
-
-v2.00 (991112)
-    New features:
-
-	- Full source released under GPL
-
-v1.05 (991023)
-    Problems fixed:
-
-	- Compilation with kernel version 2.2.13 failed
-
-v1.04 (990427)
-    Changes:
-
-	- New SMT module included, changing LED functionality
-
-    Problems fixed:
-
-	- Synchronization on SMP machines was buggy
-
-v1.03 (990325)
-    Problems fixed:
-
-	- Interrupt routing on SMP machines could be incorrect
-
-v1.02 (990310)
-    New features:
-
-	- Support for kernel versions 2.2.x added
-	- Kernel patch instead of private duplicate of kernel functions
-
-v1.01 (980812)
-    Problems fixed:
-
-	Connection hangup with telnet
-	Slow telnet connection
-
-v1.00 beta 01 (980507)
-    New features:
-
-	None.
-
-    Problems fixed:
-
-	None.
-
-    Known limitations:
-
-	- tar archive instead of standard package format (rpm).
-	- FDDI statistic is empty.
-	- not tested with 2.1.xx kernels
-	- integration in kernel not tested
-	- not tested simultaneously with FDDI adapters from other vendors.
-	- only X86 processors supported.
-	- SBA (Synchronous Bandwidth Allocator) parameters can
-	  not be configured.
-	- does not work on some COMPAQ machines. See the PCI howto
-	  document for details about this problem.
-	- data corruption with kernel versions below 2.0.33.