docs: hwmon: Add an index file and rename docs to *.rst

Now that all files were converted to ReST format, rename them
and add an index.

Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

1 files changed, 0 insertions, 113 deletions

diff --git a/Documentation/hwmon/w83793 b/Documentation/hwmon/w83793
deleted file mode 100644
index 83bb40c48645..000000000000
--- a/Documentation/hwmon/w83793
+++ /dev/null
@@ -1,113 +0,0 @@
-Kernel driver w83793
-====================
-
-Supported chips:
-
-  * Winbond W83793G/W83793R
-
-    Prefix: 'w83793'
-
-    Addresses scanned: I2C 0x2c - 0x2f
-
-    Datasheet: Still not published
-
-Authors:
-    - Yuan Mu (Winbond Electronics)
-    - Rudolf Marek <r.marek@assembler.cz>
-
-
-Module parameters
------------------
-
-* reset int
-    (default 0)
-
-    This parameter is not recommended, it will lose motherboard specific
-    settings. Use 'reset=1' to reset the chip when loading this module.
-
-* force_subclients=bus,caddr,saddr1,saddr2
-    This is used to force the i2c addresses for subclients of
-    a certain chip. Typical usage is `force_subclients=0,0x2f,0x4a,0x4b`
-    to force the subclients of chip 0x2f on bus 0 to i2c addresses
-    0x4a and 0x4b.
-
-
-Description
------------
-
-This driver implements support for Winbond W83793G/W83793R chips.
-
-* Exported features
-    This driver exports 10 voltage sensors, up to 12 fan tachometer inputs,
-    6 remote temperatures, up to 8 sets of PWM fan controls, SmartFan
-    (automatic fan speed control) on all temperature/PWM combinations, 2
-    sets of 6-pin CPU VID input.
-
-* Sensor resolutions
-    If your motherboard maker used the reference design, the resolution of
-    voltage0-2 is 2mV, resolution of voltage3/4/5 is 16mV, 8mV for voltage6,
-    24mV for voltage7/8. Temp1-4 have a 0.25 degree Celsius resolution,
-    temp5-6 have a 1 degree Celsiis resolution.
-
-* Temperature sensor types
-    Temp1-4 have 2 possible types. It can be read from (and written to)
-    temp[1-4]_type.
-
-    - If the value is 3, it starts monitoring using a remote termal diode
-      (default).
-    - If the value is 6, it starts monitoring using the temperature sensor
-      in Intel CPU and get result by PECI.
-
-    Temp5-6 can be connected to external thermistors (value of
-    temp[5-6]_type is 4).
-
-* Alarm mechanism
-    For voltage sensors, an alarm triggers if the measured value is below
-    the low voltage limit or over the high voltage limit.
-    For temperature sensors, an alarm triggers if the measured value goes
-    above the high temperature limit, and wears off only after the measured
-    value drops below the hysteresis value.
-    For fan sensors, an alarm triggers if the measured value is below the
-    low speed limit.
-
-* SmartFan/PWM control
-    If you want to set a pwm fan to manual mode, you just need to make sure it
-    is not controlled by any temp channel, for example, you want to set fan1
-    to manual mode, you need to check the value of temp[1-6]_fan_map, make
-    sure bit 0 is cleared in the 6 values. And then set the pwm1 value to
-    control the fan.
-
-    Each temperature channel can control all the 8 PWM outputs (by setting the
-    corresponding bit in tempX_fan_map), you can set the temperature channel
-    mode using temp[1-6]_pwm_enable, 2 is Thermal Cruise mode and 3
-    is the SmartFanII mode. Temperature channels will try to speed up or
-    slow down all controlled fans, this means one fan can receive different
-    PWM value requests from different temperature channels, but the chip
-    will always pick the safest (max) PWM value for each fan.
-
-    In Thermal Cruise mode, the chip attempts to keep the temperature at a
-    predefined value, within a tolerance margin. So if tempX_input >
-    thermal_cruiseX + toleranceX, the chip will increase the PWM value,
-    if tempX_input < thermal_cruiseX - toleranceX, the chip will decrease
-    the PWM value. If the temperature is within the tolerance range, the PWM
-    value is left unchanged.
-
-    SmartFanII works differently, you have to define up to 7 PWM, temperature
-    trip points, defining a PWM/temperature curve which the chip will follow.
-    While not fundamentally different from the Thermal Cruise mode, the
-    implementation is quite different, giving you a finer-grained control.
-
-* Chassis
-    If the case open alarm triggers, it will stay in this state unless cleared
-    by writing 0 to the sysfs file "intrusion0_alarm".
-
-* VID and VRM
-    The VRM version is detected automatically, don't modify the it unless you
-    *do* know the cpu VRM version and it's not properly detected.
-
-
-Notes
------
-
-  Only Fan1-5 and PWM1-3 are guaranteed to always exist, other fan inputs and
-  PWM outputs may or may not exist depending on the chip pin configuration.