Merge branch 'remove-phylink_validate-from-felix-dsa-driver'

Vladimir Oltean says:

====================
Remove phylink_validate() from Felix DSA driver

The Felix DSA driver still uses its own phylink_validate() procedure
rather than the (relatively newly introduced) phylink_generic_validate()
because the latter did not cater for the case where a PHY provides rate
matching between the Ethernet cable side speed and the SERDES side
speed (and does not advertise other speeds except for the SERDES speed).

This changed with Sean Anderson's generic support for rate matching PHYs
in phylib and phylink:
https://patchwork.kernel.org/project/netdevbpf/cover/20220920221235.1487501-1-sean.anderson@seco.com/

Building upon that support, this patch set makes Linux understand that
the PHYs used in combination with the Felix DSA driver (SCH-30841 riser
card with AQR412 PHY, used with SERDES protocol 0x7777 - 4x2500base-x,
plugged into LS1028A-QDS) do support PAUSE rate matching. This requires
Aquantia PHY driver support for new PHY IDs.

To activate the rate matching support in phylink, config->mac_capabilities
must be populated. Coincidentally, this also opts the Felix driver into
the generic phylink validation.

Next, code that is no longer necessary is eliminated. This includes the
Felix driver validation procedures for VSC9959 and VSC9953, the
workaround in the Ocelot switch library to leave RX flow control always
enabled, as well as DSA plumbing necessary for a custom phylink
validation procedure to be propagated to the hardware driver level.

Many thanks go to Sean Anderson for providing generic support for rate
matching.
====================

Link: https://lore.kernel.org/r/20221114170730.2189282-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

8 files changed, 54 insertions, 89 deletions

diff --git a/drivers/net/dsa/ocelot/felix.c b/drivers/net/dsa/ocelot/felix.c
index dd3a18cc89dd..44e160f32067 100644
--- a/drivers/net/dsa/ocelot/felix.c
+++ b/drivers/net/dsa/ocelot/felix.c
@@ -1048,21 +1048,14 @@ static void felix_phylink_get_caps(struct dsa_switch *ds, int port,
 	 */
 	config->legacy_pre_march2020 = false;
 
+	config->mac_capabilities = MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
+				   MAC_10 | MAC_100 | MAC_1000FD |
+				   MAC_2500FD;
+
 	__set_bit(ocelot->ports[port]->phy_mode,
 		  config->supported_interfaces);
 }
 
-static void felix_phylink_validate(struct dsa_switch *ds, int port,
-				   unsigned long *supported,
-				   struct phylink_link_state *state)
-{
-	struct ocelot *ocelot = ds->priv;
-	struct felix *felix = ocelot_to_felix(ocelot);
-
-	if (felix->info->phylink_validate)
-		felix->info->phylink_validate(ocelot, port, supported, state);
-}
-
 static struct phylink_pcs *felix_phylink_mac_select_pcs(struct dsa_switch *ds,
 							int port,
 							phy_interface_t iface)
@@ -2050,7 +2043,6 @@ const struct dsa_switch_ops felix_switch_ops = {
 	.get_sset_count			= felix_get_sset_count,
 	.get_ts_info			= felix_get_ts_info,
 	.phylink_get_caps		= felix_phylink_get_caps,
-	.phylink_validate		= felix_phylink_validate,
 	.phylink_mac_select_pcs		= felix_phylink_mac_select_pcs,
 	.phylink_mac_link_down		= felix_phylink_mac_link_down,
 	.phylink_mac_link_up		= felix_phylink_mac_link_up,
diff --git a/drivers/net/dsa/ocelot/felix.h b/drivers/net/dsa/ocelot/felix.h
index c9c29999c336..42338116eed0 100644
--- a/drivers/net/dsa/ocelot/felix.h
+++ b/drivers/net/dsa/ocelot/felix.h
@@ -52,9 +52,6 @@ struct felix_info {
 
 	int	(*mdio_bus_alloc)(struct ocelot *ocelot);
 	void	(*mdio_bus_free)(struct ocelot *ocelot);
-	void	(*phylink_validate)(struct ocelot *ocelot, int port,
-				    unsigned long *supported,
-				    struct phylink_link_state *state);
 	int	(*port_setup_tc)(struct dsa_switch *ds, int port,
 				 enum tc_setup_type type, void *type_data);
 	void	(*tas_guard_bands_update)(struct ocelot *ocelot, int port);
diff --git a/drivers/net/dsa/ocelot/felix_vsc9959.c b/drivers/net/dsa/ocelot/felix_vsc9959.c
index 26a35ae322d1..b0ae8d6156f6 100644
--- a/drivers/net/dsa/ocelot/felix_vsc9959.c
+++ b/drivers/net/dsa/ocelot/felix_vsc9959.c
@@ -885,35 +885,6 @@ static int vsc9959_reset(struct ocelot *ocelot)
 	return 0;
 }
 
-static void vsc9959_phylink_validate(struct ocelot *ocelot, int port,
-				     unsigned long *supported,
-				     struct phylink_link_state *state)
-{
-	__ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
-
-	phylink_set_port_modes(mask);
-	phylink_set(mask, Autoneg);
-	phylink_set(mask, Pause);
-	phylink_set(mask, Asym_Pause);
-	phylink_set(mask, 10baseT_Half);
-	phylink_set(mask, 10baseT_Full);
-	phylink_set(mask, 100baseT_Half);
-	phylink_set(mask, 100baseT_Full);
-	phylink_set(mask, 1000baseT_Half);
-	phylink_set(mask, 1000baseT_Full);
-	phylink_set(mask, 1000baseX_Full);
-
-	if (state->interface == PHY_INTERFACE_MODE_INTERNAL ||
-	    state->interface == PHY_INTERFACE_MODE_2500BASEX ||
-	    state->interface == PHY_INTERFACE_MODE_USXGMII) {
-		phylink_set(mask, 2500baseT_Full);
-		phylink_set(mask, 2500baseX_Full);
-	}
-
-	linkmode_and(supported, supported, mask);
-	linkmode_and(state->advertising, state->advertising, mask);
-}
-
 /* Watermark encode
  * Bit 8:   Unit; 0:1, 1:16
  * Bit 7-0: Value to be multiplied with unit
@@ -2588,7 +2559,6 @@ static const struct felix_info felix_info_vsc9959 = {
 	.ptp_caps		= &vsc9959_ptp_caps,
 	.mdio_bus_alloc		= vsc9959_mdio_bus_alloc,
 	.mdio_bus_free		= vsc9959_mdio_bus_free,
-	.phylink_validate	= vsc9959_phylink_validate,
 	.port_modes		= vsc9959_port_modes,
 	.port_setup_tc		= vsc9959_port_setup_tc,
 	.port_sched_speed_set	= vsc9959_sched_speed_set,
diff --git a/drivers/net/dsa/ocelot/seville_vsc9953.c b/drivers/net/dsa/ocelot/seville_vsc9953.c
index 7af33b2c685d..6500c1697dd6 100644
--- a/drivers/net/dsa/ocelot/seville_vsc9953.c
+++ b/drivers/net/dsa/ocelot/seville_vsc9953.c
@@ -840,32 +840,6 @@ static int vsc9953_reset(struct ocelot *ocelot)
 	return 0;
 }
 
-static void vsc9953_phylink_validate(struct ocelot *ocelot, int port,
-				     unsigned long *supported,
-				     struct phylink_link_state *state)
-{
-	__ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
-
-	phylink_set_port_modes(mask);
-	phylink_set(mask, Autoneg);
-	phylink_set(mask, Pause);
-	phylink_set(mask, Asym_Pause);
-	phylink_set(mask, 10baseT_Full);
-	phylink_set(mask, 10baseT_Half);
-	phylink_set(mask, 100baseT_Full);
-	phylink_set(mask, 100baseT_Half);
-	phylink_set(mask, 1000baseT_Full);
-	phylink_set(mask, 1000baseX_Full);
-
-	if (state->interface == PHY_INTERFACE_MODE_INTERNAL) {
-		phylink_set(mask, 2500baseT_Full);
-		phylink_set(mask, 2500baseX_Full);
-	}
-
-	linkmode_and(supported, supported, mask);
-	linkmode_and(state->advertising, state->advertising, mask);
-}
-
 /* Watermark encode
  * Bit 9:   Unit; 0:1, 1:16
  * Bit 8-0: Value to be multiplied with unit
@@ -1007,7 +981,6 @@ static const struct felix_info seville_info_vsc9953 = {
 	.num_tx_queues		= OCELOT_NUM_TC,
 	.mdio_bus_alloc		= vsc9953_mdio_bus_alloc,
 	.mdio_bus_free		= vsc9953_mdio_bus_free,
-	.phylink_validate	= vsc9953_phylink_validate,
 	.port_modes		= vsc9953_port_modes,
 };
 
diff --git a/drivers/net/ethernet/mscc/ocelot.c b/drivers/net/ethernet/mscc/ocelot.c
index 13b14110a060..da56f9bfeaf0 100644
--- a/drivers/net/ethernet/mscc/ocelot.c
+++ b/drivers/net/ethernet/mscc/ocelot.c
@@ -872,10 +872,8 @@ void ocelot_phylink_mac_link_up(struct ocelot *ocelot, int port,
 		return;
 	}
 
-	/* Handle RX pause in all cases, with 2500base-X this is used for rate
-	 * adaptation.
-	 */
-	mac_fc_cfg |= SYS_MAC_FC_CFG_RX_FC_ENA;
+	if (rx_pause)
+		mac_fc_cfg |= SYS_MAC_FC_CFG_RX_FC_ENA;
 
 	if (tx_pause)
 		mac_fc_cfg |= SYS_MAC_FC_CFG_TX_FC_ENA |
diff --git a/drivers/net/phy/aquantia_main.c b/drivers/net/phy/aquantia_main.c
index 47a76df36b74..334a6904ca5a 100644
--- a/drivers/net/phy/aquantia_main.c
+++ b/drivers/net/phy/aquantia_main.c
@@ -22,6 +22,8 @@
 #define PHY_ID_AQR107	0x03a1b4e0
 #define PHY_ID_AQCS109	0x03a1b5c2
 #define PHY_ID_AQR405	0x03a1b4b0
+#define PHY_ID_AQR112	0x03a1b662
+#define PHY_ID_AQR412	0x03a1b712
 #define PHY_ID_AQR113C	0x31c31c12
 
 #define MDIO_PHYXS_VEND_IF_STATUS		0xe812
@@ -801,6 +803,42 @@ static struct phy_driver aqr_driver[] = {
 	.read_status	= aqr_read_status,
 },
 {
+	PHY_ID_MATCH_MODEL(PHY_ID_AQR112),
+	.name		= "Aquantia AQR112",
+	.probe		= aqr107_probe,
+	.config_aneg    = aqr_config_aneg,
+	.config_intr	= aqr_config_intr,
+	.handle_interrupt = aqr_handle_interrupt,
+	.get_tunable    = aqr107_get_tunable,
+	.set_tunable    = aqr107_set_tunable,
+	.suspend	= aqr107_suspend,
+	.resume		= aqr107_resume,
+	.read_status	= aqr107_read_status,
+	.get_rate_matching = aqr107_get_rate_matching,
+	.get_sset_count = aqr107_get_sset_count,
+	.get_strings	= aqr107_get_strings,
+	.get_stats	= aqr107_get_stats,
+	.link_change_notify = aqr107_link_change_notify,
+},
+{
+	PHY_ID_MATCH_MODEL(PHY_ID_AQR412),
+	.name		= "Aquantia AQR412",
+	.probe		= aqr107_probe,
+	.config_aneg    = aqr_config_aneg,
+	.config_intr	= aqr_config_intr,
+	.handle_interrupt = aqr_handle_interrupt,
+	.get_tunable    = aqr107_get_tunable,
+	.set_tunable    = aqr107_set_tunable,
+	.suspend	= aqr107_suspend,
+	.resume		= aqr107_resume,
+	.read_status	= aqr107_read_status,
+	.get_rate_matching = aqr107_get_rate_matching,
+	.get_sset_count = aqr107_get_sset_count,
+	.get_strings	= aqr107_get_strings,
+	.get_stats	= aqr107_get_stats,
+	.link_change_notify = aqr107_link_change_notify,
+},
+{
 	PHY_ID_MATCH_MODEL(PHY_ID_AQR113C),
 	.name           = "Aquantia AQR113C",
 	.probe          = aqr107_probe,
@@ -831,6 +869,8 @@ static struct mdio_device_id __maybe_unused aqr_tbl[] = {
 	{ PHY_ID_MATCH_MODEL(PHY_ID_AQR107) },
 	{ PHY_ID_MATCH_MODEL(PHY_ID_AQCS109) },
 	{ PHY_ID_MATCH_MODEL(PHY_ID_AQR405) },
+	{ PHY_ID_MATCH_MODEL(PHY_ID_AQR112) },
+	{ PHY_ID_MATCH_MODEL(PHY_ID_AQR412) },
 	{ PHY_ID_MATCH_MODEL(PHY_ID_AQR113C) },
 	{ }
 };
diff --git a/include/net/dsa.h b/include/net/dsa.h
index ee369670e20e..dde364688739 100644
--- a/include/net/dsa.h
+++ b/include/net/dsa.h
@@ -880,9 +880,6 @@ struct dsa_switch_ops {
 	 */
 	void	(*phylink_get_caps)(struct dsa_switch *ds, int port,
 				    struct phylink_config *config);
-	void	(*phylink_validate)(struct dsa_switch *ds, int port,
-				    unsigned long *supported,
-				    struct phylink_link_state *state);
 	struct phylink_pcs *(*phylink_mac_select_pcs)(struct dsa_switch *ds,
 						      int port,
 						      phy_interface_t iface);
diff --git a/net/dsa/port.c b/net/dsa/port.c
index 208168276995..48c9eaa74aee 100644
--- a/net/dsa/port.c
+++ b/net/dsa/port.c
@@ -1536,16 +1536,14 @@ static void dsa_port_phylink_validate(struct phylink_config *config,
 				      unsigned long *supported,
 				      struct phylink_link_state *state)
 {
-	struct dsa_port *dp = container_of(config, struct dsa_port, pl_config);
-	struct dsa_switch *ds = dp->ds;
-
-	if (!ds->ops->phylink_validate) {
-		if (config->mac_capabilities)
-			phylink_generic_validate(config, supported, state);
-		return;
-	}
-
-	ds->ops->phylink_validate(ds, dp->index, supported, state);
+	/* Skip call for drivers which don't yet set mac_capabilities,
+	 * since validating in that case would mean their PHY will advertise
+	 * nothing. In turn, skipping validation makes them advertise
+	 * everything that the PHY supports, so those drivers should be
+	 * converted ASAP.
+	 */
+	if (config->mac_capabilities)
+		phylink_generic_validate(config, supported, state);
 }
 
 static void dsa_port_phylink_mac_pcs_get_state(struct phylink_config *config,