Merge branch 'adin1100-industrial-PHY-support'

Alexandru Tachici says:

====================
net: phy: adin1100: Add initial support for ADIN1100 industrial PHY

The ADIN1100 is a low power single port 10BASE-T1L transceiver designed for
industrial Ethernet applications and is compliant with the IEEE 802.3cg
Ethernet standard for long reach 10 Mb/s Single Pair Ethernet.

The ADIN1100 uses Auto-Negotiation capability in accordance
with IEEE 802.3 Clause 98, providing a mechanism for
exchanging information between PHYs to allow link partners to
agree to a common mode of operation.

The concluded operating mode is the transmit amplitude mode and
master/slave preference common across the two devices.

Both device and LP advertise their ability and request for
increased transmit at:
- BASE-T1 autonegotiation advertisement register [47:32]\
Clause 45.2.7.21 of Standard 802.3
- BIT(13) - 10BASE-T1L High Level Transmit Operating Mode Ability
- BIT(12) - 10BASE-T1L High Level Transmit Operating Mode Request

For 2.4 Vpp (high level transmit) operation, both devices need
to have the High Level Transmit Operating Mode Ability bit set,
and only one of them needs to have the High Level Transmit
Operating Mode Request bit set. Otherwise 1.0 Vpp transmit level
will be used.

Settings for eth1:
	Supported ports: [ TP	 MII ]
	Supported link modes:   10baseT1L/Full
	Supported pause frame use: Symmetric Receive-only
	Supports auto-negotiation: Yes
	Supported FEC modes: Not reported
	Advertised link modes:  10baseT1L/Full
	Advertised pause frame use: No
	Advertised auto-negotiation: Yes
	Advertised FEC modes: Not reported
	Link partner advertised link modes:  10baseT1L/Full
	Link partner advertised pause frame use: No
	Link partner advertised auto-negotiation: Yes
	Link partner advertised FEC modes: Not reported
	Speed: 10Mb/s
	Duplex: Full
	Auto-negotiation: on
	master-slave cfg: preferred slave
	master-slave status: slave
	Port: Twisted Pair
	PHYAD: 0
	Transceiver: external
	MDI-X: Unknown
	Link detected: yes
	SQI: 7/7

1. Add basic support for ADIN1100.

Alexandru Ardelean (1):
  net: phy: adin1100: Add initial support for ADIN1100 industrial PHY

1. Added 10baset-T1L link modes.

2. Added 10-BasetT1L registers.

3. Added Base-T1 auto-negotiation registers. For Base-T1 these
registers decide master/slave status and TX voltage of the
device and link partner.

4. Added 10BASE-T1L support in phy-c45.c. Now genphy functions will call
Base-T1 functions where registers don't match, like the auto-negotiation ones.

5. Convert MSE to SQI using a predefined table and allow user access
through ethtool.

6. DT bindings for the 2.4 Vpp transmit mode.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

13 files changed, 722 insertions, 9 deletions

diff --git a/Documentation/devicetree/bindings/net/ethernet-phy.yaml b/Documentation/devicetree/bindings/net/ethernet-phy.yaml
index ee42328a109d..ed1415a4381f 100644
--- a/Documentation/devicetree/bindings/net/ethernet-phy.yaml
+++ b/Documentation/devicetree/bindings/net/ethernet-phy.yaml
@@ -77,6 +77,15 @@ properties:
     description:
       Maximum PHY supported speed in Mbits / seconds.
 
+  phy-10base-t1l-2.4vpp:
+    description: |
+      tristate, request/disable 2.4 Vpp operating mode. The values are:
+      0: Disable 2.4 Vpp operating mode.
+      1: Request 2.4 Vpp operating mode from link partner.
+      Absence of this property will leave configuration to default values.
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    enum: [0, 1]
+
   broken-turn-around:
     $ref: /schemas/types.yaml#/definitions/flag
     description:
diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index ea7571a2b39b..bbbf6c07ea53 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -83,6 +83,13 @@ config ADIN_PHY
 	  - ADIN1300 - Robust,Industrial, Low Latency 10/100/1000 Gigabit
 	    Ethernet PHY
 
+config ADIN1100_PHY
+	tristate "Analog Devices Industrial Ethernet T1L PHYs"
+	help
+	  Adds support for the Analog Devices Industrial T1L Ethernet PHYs.
+	  Currently supports the:
+	  - ADIN1100 - Robust,Industrial, Low Power 10BASE-T1L Ethernet PHY
+
 config AQUANTIA_PHY
 	tristate "Aquantia PHYs"
 	help
diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
index b2728d00fc9a..b82651b57043 100644
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -31,6 +31,7 @@ sfp-obj-$(CONFIG_SFP)		+= sfp-bus.o
 obj-y				+= $(sfp-obj-y) $(sfp-obj-m)
 
 obj-$(CONFIG_ADIN_PHY)		+= adin.o
+obj-$(CONFIG_ADIN1100_PHY)	+= adin1100.o
 obj-$(CONFIG_AMD_PHY)		+= amd.o
 aquantia-objs			+= aquantia_main.o
 ifdef CONFIG_HWMON
diff --git a/drivers/net/phy/adin1100.c b/drivers/net/phy/adin1100.c
new file mode 100644
index 000000000000..b6d139501199
--- /dev/null
+++ b/drivers/net/phy/adin1100.c
@@ -0,0 +1,292 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ *  Driver for Analog Devices Industrial Ethernet T1L PHYs
+ *
+ * Copyright 2020 Analog Devices Inc.
+ */
+#include <linux/kernel.h>
+#include <linux/bitfield.h>
+#include <linux/delay.h>
+#include <linux/errno.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/mii.h>
+#include <linux/phy.h>
+#include <linux/property.h>
+
+#define PHY_ID_ADIN1100				0x0283bc81
+
+#define ADIN_FORCED_MODE			0x8000
+#define   ADIN_FORCED_MODE_EN			BIT(0)
+
+#define ADIN_CRSM_SFT_RST			0x8810
+#define   ADIN_CRSM_SFT_RST_EN			BIT(0)
+
+#define ADIN_CRSM_SFT_PD_CNTRL			0x8812
+#define   ADIN_CRSM_SFT_PD_CNTRL_EN		BIT(0)
+
+#define ADIN_AN_PHY_INST_STATUS			0x8030
+#define   ADIN_IS_CFG_SLV			BIT(2)
+#define   ADIN_IS_CFG_MST			BIT(3)
+
+#define ADIN_CRSM_STAT				0x8818
+#define   ADIN_CRSM_SFT_PD_RDY			BIT(1)
+#define   ADIN_CRSM_SYS_RDY			BIT(0)
+
+#define ADIN_MSE_VAL				0x830B
+
+#define ADIN_SQI_MAX	7
+
+struct adin_mse_sqi_range {
+	u16 start;
+	u16 end;
+};
+
+static const struct adin_mse_sqi_range adin_mse_sqi_map[] = {
+	{ 0x0A74, 0xFFFF },
+	{ 0x084E, 0x0A74 },
+	{ 0x0698, 0x084E },
+	{ 0x053D, 0x0698 },
+	{ 0x0429, 0x053D },
+	{ 0x034E, 0x0429 },
+	{ 0x02A0, 0x034E },
+	{ 0x0000, 0x02A0 },
+};
+
+/**
+ * struct adin_priv - ADIN PHY driver private data
+ * @tx_level_2v4_able:		set if the PHY supports 2.4V TX levels (10BASE-T1L)
+ * @tx_level_2v4:		set if the PHY requests 2.4V TX levels (10BASE-T1L)
+ * @tx_level_prop_present:	set if the TX level is specified in DT
+ */
+struct adin_priv {
+	unsigned int		tx_level_2v4_able:1;
+	unsigned int		tx_level_2v4:1;
+	unsigned int		tx_level_prop_present:1;
+};
+
+static int adin_read_status(struct phy_device *phydev)
+{
+	int ret;
+
+	ret = genphy_c45_read_status(phydev);
+	if (ret)
+		return ret;
+
+	ret = phy_read_mmd(phydev, MDIO_MMD_AN, ADIN_AN_PHY_INST_STATUS);
+	if (ret < 0)
+		return ret;
+
+	if (ret & ADIN_IS_CFG_SLV)
+		phydev->master_slave_state = MASTER_SLAVE_STATE_SLAVE;
+
+	if (ret & ADIN_IS_CFG_MST)
+		phydev->master_slave_state = MASTER_SLAVE_STATE_MASTER;
+
+	return 0;
+}
+
+static int adin_config_aneg(struct phy_device *phydev)
+{
+	struct adin_priv *priv = phydev->priv;
+	int ret;
+
+	if (phydev->autoneg == AUTONEG_DISABLE) {
+		ret = genphy_c45_pma_setup_forced(phydev);
+		if (ret < 0)
+			return ret;
+
+		if (priv->tx_level_prop_present && priv->tx_level_2v4)
+			ret = phy_set_bits_mmd(phydev, MDIO_MMD_PMAPMD, MDIO_B10L_PMA_CTRL,
+					       MDIO_PMA_10T1L_CTRL_2V4_EN);
+		else
+			ret = phy_clear_bits_mmd(phydev, MDIO_MMD_PMAPMD, MDIO_B10L_PMA_CTRL,
+						 MDIO_PMA_10T1L_CTRL_2V4_EN);
+		if (ret < 0)
+			return ret;
+
+		/* Force PHY to use above configurations */
+		return phy_set_bits_mmd(phydev, MDIO_MMD_AN, ADIN_FORCED_MODE, ADIN_FORCED_MODE_EN);
+	}
+
+	ret = phy_clear_bits_mmd(phydev, MDIO_MMD_AN, ADIN_FORCED_MODE, ADIN_FORCED_MODE_EN);
+	if (ret < 0)
+		return ret;
+
+	/* Request increased transmit level from LP. */
+	if (priv->tx_level_prop_present && priv->tx_level_2v4) {
+		ret = phy_set_bits_mmd(phydev, MDIO_MMD_AN, MDIO_AN_T1_ADV_H,
+				       MDIO_AN_T1_ADV_H_10L_TX_HI |
+				       MDIO_AN_T1_ADV_H_10L_TX_HI_REQ);
+		if (ret < 0)
+			return ret;
+	}
+
+	/* Disable 2.4 Vpp transmit level. */
+	if ((priv->tx_level_prop_present && !priv->tx_level_2v4) || !priv->tx_level_2v4_able) {
+		ret = phy_clear_bits_mmd(phydev, MDIO_MMD_AN, MDIO_AN_T1_ADV_H,
+					 MDIO_AN_T1_ADV_H_10L_TX_HI |
+					 MDIO_AN_T1_ADV_H_10L_TX_HI_REQ);
+		if (ret < 0)
+			return ret;
+	}
+
+	return genphy_c45_config_aneg(phydev);
+}
+
+static int adin_set_powerdown_mode(struct phy_device *phydev, bool en)
+{
+	int ret;
+	int val;
+
+	val = en ? ADIN_CRSM_SFT_PD_CNTRL_EN : 0;
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND1,
+			    ADIN_CRSM_SFT_PD_CNTRL, val);
+	if (ret < 0)
+		return ret;
+
+	return phy_read_mmd_poll_timeout(phydev, MDIO_MMD_VEND1, ADIN_CRSM_STAT, ret,
+					 (ret & ADIN_CRSM_SFT_PD_RDY) == val,
+					 1000, 30000, true);
+}
+
+static int adin_suspend(struct phy_device *phydev)
+{
+	return adin_set_powerdown_mode(phydev, true);
+}
+
+static int adin_resume(struct phy_device *phydev)
+{
+	return adin_set_powerdown_mode(phydev, false);
+}
+
+static int adin_set_loopback(struct phy_device *phydev, bool enable)
+{
+	if (enable)
+		return phy_set_bits_mmd(phydev, MDIO_MMD_PCS, MDIO_PCS_10T1L_CTRL,
+					BMCR_LOOPBACK);
+
+	/* PCS loopback (according to 10BASE-T1L spec) */
+	return phy_clear_bits_mmd(phydev, MDIO_MMD_PCS, MDIO_PCS_10T1L_CTRL,
+				 BMCR_LOOPBACK);
+}
+
+static int adin_soft_reset(struct phy_device *phydev)
+{
+	int ret;
+
+	ret = phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, ADIN_CRSM_SFT_RST, ADIN_CRSM_SFT_RST_EN);
+	if (ret < 0)
+		return ret;
+
+	return phy_read_mmd_poll_timeout(phydev, MDIO_MMD_VEND1, ADIN_CRSM_STAT, ret,
+					 (ret & ADIN_CRSM_SYS_RDY),
+					 10000, 30000, true);
+}
+
+static int adin_get_features(struct phy_device *phydev)
+{
+	struct adin_priv *priv = phydev->priv;
+	struct device *dev = &phydev->mdio.dev;
+	int ret;
+	u8 val;
+
+	ret = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, MDIO_PMA_10T1L_STAT);
+	if (ret < 0)
+		return ret;
+
+	/* This depends on the voltage level from the power source */
+	priv->tx_level_2v4_able = !!(ret & MDIO_PMA_10T1L_STAT_2V4_ABLE);
+
+	phydev_dbg(phydev, "PHY supports 2.4V TX level: %s\n",
+		   priv->tx_level_2v4_able ? "yes" : "no");
+
+	priv->tx_level_prop_present = device_property_present(dev, "phy-10base-t1l-2.4vpp");
+	if (priv->tx_level_prop_present) {
+		ret = device_property_read_u8(dev, "phy-10base-t1l-2.4vpp", &val);
+		if (ret < 0)
+			return ret;
+
+		priv->tx_level_2v4 = val;
+		if (!priv->tx_level_2v4 && priv->tx_level_2v4_able)
+			phydev_info(phydev,
+				    "PHY supports 2.4V TX level, but disabled via config\n");
+	}
+
+	linkmode_set_bit_array(phy_basic_ports_array, ARRAY_SIZE(phy_basic_ports_array),
+			       phydev->supported);
+
+	return genphy_c45_pma_read_abilities(phydev);
+}
+
+static int adin_get_sqi(struct phy_device *phydev)
+{
+	u16 mse_val;
+	int sqi;
+	int ret;
+
+	ret = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, MDIO_STAT1);
+	if (ret < 0)
+		return ret;
+	else if (!(ret & MDIO_STAT1_LSTATUS))
+		return 0;
+
+	ret = phy_read_mmd(phydev, MDIO_STAT1, ADIN_MSE_VAL);
+	if (ret < 0)
+		return ret;
+
+	mse_val = 0xFFFF & ret;
+	for (sqi = 0; sqi < ARRAY_SIZE(adin_mse_sqi_map); sqi++) {
+		if (mse_val >= adin_mse_sqi_map[sqi].start && mse_val <= adin_mse_sqi_map[sqi].end)
+			return sqi;
+	}
+
+	return -EINVAL;
+}
+
+static int adin_get_sqi_max(struct phy_device *phydev)
+{
+	return ADIN_SQI_MAX;
+}
+
+static int adin_probe(struct phy_device *phydev)
+{
+	struct device *dev = &phydev->mdio.dev;
+	struct adin_priv *priv;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	phydev->priv = priv;
+
+	return 0;
+}
+
+static struct phy_driver adin_driver[] = {
+	{
+		PHY_ID_MATCH_MODEL(PHY_ID_ADIN1100),
+		.name			= "ADIN1100",
+		.get_features		= adin_get_features,
+		.soft_reset		= adin_soft_reset,
+		.probe			= adin_probe,
+		.config_aneg		= adin_config_aneg,
+		.read_status		= adin_read_status,
+		.set_loopback		= adin_set_loopback,
+		.suspend		= adin_suspend,
+		.resume			= adin_resume,
+		.get_sqi		= adin_get_sqi,
+		.get_sqi_max		= adin_get_sqi_max,
+	},
+};
+
+module_phy_driver(adin_driver);
+
+static struct mdio_device_id __maybe_unused adin_tbl[] = {
+	{ PHY_ID_MATCH_MODEL(PHY_ID_ADIN1100) },
+	{ }
+};
+
+MODULE_DEVICE_TABLE(mdio, adin_tbl);
+MODULE_DESCRIPTION("Analog Devices Industrial Ethernet T1L PHY driver");
+MODULE_LICENSE("Dual BSD/GPL");
diff --git a/drivers/net/phy/phy-c45.c b/drivers/net/phy/phy-c45.c
index db709d30bf84..eefdd67d5556 100644
--- a/drivers/net/phy/phy-c45.c
+++ b/drivers/net/phy/phy-c45.c
@@ -9,6 +9,25 @@
 #include <linux/phy.h>
 
 /**
+ * genphy_c45_baset1_able - checks if the PMA has BASE-T1 extended abilities
+ * @phydev: target phy_device struct
+ */
+static bool genphy_c45_baset1_able(struct phy_device *phydev)
+{
+	int val;
+
+	if (phydev->pma_extable == -ENODATA) {
+		val = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, MDIO_PMA_EXTABLE);
+		if (val < 0)
+			return false;
+
+		phydev->pma_extable = val;
+	}
+
+	return !!(phydev->pma_extable & MDIO_PMA_EXTABLE_BT1);
+}
+
+/**
  * genphy_c45_pma_can_sleep - checks if the PMA have sleep support
  * @phydev: target phy_device struct
  */
@@ -80,7 +99,10 @@ int genphy_c45_pma_setup_forced(struct phy_device *phydev)
 
 	switch (phydev->speed) {
 	case SPEED_10:
-		ctrl2 |= MDIO_PMA_CTRL2_10BT;
+		if (genphy_c45_baset1_able(phydev))
+			ctrl2 |= MDIO_PMA_CTRL2_BASET1;
+		else
+			ctrl2 |= MDIO_PMA_CTRL2_10BT;
 		break;
 	case SPEED_100:
 		ctrl1 |= MDIO_PMA_CTRL1_SPEED100;
@@ -118,10 +140,95 @@ int genphy_c45_pma_setup_forced(struct phy_device *phydev)
 	if (ret < 0)
 		return ret;
 
+	if (genphy_c45_baset1_able(phydev)) {
+		int ctl = 0;
+
+		switch (phydev->master_slave_set) {
+		case MASTER_SLAVE_CFG_MASTER_PREFERRED:
+		case MASTER_SLAVE_CFG_MASTER_FORCE:
+			ctl = MDIO_PMA_PMD_BT1_CTRL_CFG_MST;
+			break;
+		case MASTER_SLAVE_CFG_SLAVE_FORCE:
+		case MASTER_SLAVE_CFG_SLAVE_PREFERRED:
+		case MASTER_SLAVE_CFG_UNKNOWN:
+		case MASTER_SLAVE_CFG_UNSUPPORTED:
+			break;
+		default:
+			phydev_warn(phydev, "Unsupported Master/Slave mode\n");
+			return -EOPNOTSUPP;
+		}
+
+		ret = phy_modify_mmd(phydev, MDIO_MMD_PMAPMD, MDIO_PMA_PMD_BT1_CTRL,
+				     MDIO_PMA_PMD_BT1_CTRL_CFG_MST, ctl);
+		if (ret < 0)
+			return ret;
+	}
+
 	return genphy_c45_an_disable_aneg(phydev);
 }
 EXPORT_SYMBOL_GPL(genphy_c45_pma_setup_forced);
 
+/* Sets master/slave preference and supported technologies.
+ * The preference is set in the BIT(4) of BASE-T1 AN
+ * advertisement register 7.515 and whether the status
+ * is forced or not, it is set in the BIT(12) of BASE-T1
+ * AN advertisement register 7.514.
+ * Sets 10BASE-T1L Ability BIT(14) in BASE-T1 autonegotiation
+ * advertisement register [31:16] if supported.
+ */
+static int genphy_c45_baset1_an_config_aneg(struct phy_device *phydev)
+{
+	int changed = 0;
+	u16 adv_l = 0;
+	u16 adv_m = 0;
+	int ret;
+
+	switch (phydev->master_slave_set) {
+	case MASTER_SLAVE_CFG_MASTER_FORCE:
+	case MASTER_SLAVE_CFG_SLAVE_FORCE:
+		adv_l |= MDIO_AN_T1_ADV_L_FORCE_MS;
+		break;
+	case MASTER_SLAVE_CFG_MASTER_PREFERRED:
+	case MASTER_SLAVE_CFG_SLAVE_PREFERRED:
+		break;
+	default:
+		break;
+	}
+
+	switch (phydev->master_slave_set) {
+	case MASTER_SLAVE_CFG_MASTER_FORCE:
+	case MASTER_SLAVE_CFG_MASTER_PREFERRED:
+		adv_m |= MDIO_AN_T1_ADV_M_MST;
+		break;
+	case MASTER_SLAVE_CFG_SLAVE_FORCE:
+	case MASTER_SLAVE_CFG_SLAVE_PREFERRED:
+		break;
+	default:
+		break;
+	}
+
+	adv_l |= linkmode_adv_to_mii_t1_adv_l_t(phydev->advertising);
+
+	ret = phy_modify_mmd_changed(phydev, MDIO_MMD_AN, MDIO_AN_T1_ADV_L,
+				     (MDIO_AN_T1_ADV_L_FORCE_MS | MDIO_AN_T1_ADV_L_PAUSE_CAP
+				     | MDIO_AN_T1_ADV_L_PAUSE_ASYM), adv_l);
+	if (ret < 0)
+		return ret;
+	if (ret > 0)
+		changed = 1;
+
+	adv_m |= linkmode_adv_to_mii_t1_adv_m_t(phydev->advertising);
+
+	ret = phy_modify_mmd_changed(phydev, MDIO_MMD_AN, MDIO_AN_T1_ADV_M,
+				     MDIO_AN_T1_ADV_M_MST | MDIO_AN_T1_ADV_M_B10L, adv_m);
+	if (ret < 0)
+		return ret;
+	if (ret > 0)
+		changed = 1;
+
+	return changed;
+}
+
 /**
  * genphy_c45_an_config_aneg - configure advertisement registers
  * @phydev: target phy_device struct
@@ -141,6 +248,9 @@ int genphy_c45_an_config_aneg(struct phy_device *phydev)
 
 	changed = genphy_config_eee_advert(phydev);
 
+	if (genphy_c45_baset1_able(phydev))
+		return genphy_c45_baset1_an_config_aneg(phydev);
+
 	adv = linkmode_adv_to_mii_adv_t(phydev->advertising);
 
 	ret = phy_modify_mmd_changed(phydev, MDIO_MMD_AN, MDIO_AN_ADVERTISE,
@@ -178,8 +288,12 @@ EXPORT_SYMBOL_GPL(genphy_c45_an_config_aneg);
  */
 int genphy_c45_an_disable_aneg(struct phy_device *phydev)
 {
+	u16 reg = MDIO_CTRL1;
 
-	return phy_clear_bits_mmd(phydev, MDIO_MMD_AN, MDIO_CTRL1,
+	if (genphy_c45_baset1_able(phydev))
+		reg = MDIO_AN_T1_CTRL;
+
+	return phy_clear_bits_mmd(phydev, MDIO_MMD_AN, reg,
 				  MDIO_AN_CTRL1_ENABLE | MDIO_AN_CTRL1_RESTART);
 }
 EXPORT_SYMBOL_GPL(genphy_c45_an_disable_aneg);
@@ -194,7 +308,12 @@ EXPORT_SYMBOL_GPL(genphy_c45_an_disable_aneg);
  */
 int genphy_c45_restart_aneg(struct phy_device *phydev)
 {
-	return phy_set_bits_mmd(phydev, MDIO_MMD_AN, MDIO_CTRL1,
+	u16 reg = MDIO_CTRL1;
+
+	if (genphy_c45_baset1_able(phydev))
+		reg = MDIO_AN_T1_CTRL;
+
+	return phy_set_bits_mmd(phydev, MDIO_MMD_AN, reg,
 				MDIO_AN_CTRL1_ENABLE | MDIO_AN_CTRL1_RESTART);
 }
 EXPORT_SYMBOL_GPL(genphy_c45_restart_aneg);
@@ -210,11 +329,15 @@ EXPORT_SYMBOL_GPL(genphy_c45_restart_aneg);
  */
 int genphy_c45_check_and_restart_aneg(struct phy_device *phydev, bool restart)
 {
+	u16 reg = MDIO_CTRL1;
 	int ret;
 
+	if (genphy_c45_baset1_able(phydev))
+		reg = MDIO_AN_T1_CTRL;
+
 	if (!restart) {
 		/* Configure and restart aneg if it wasn't set before */
-		ret = phy_read_mmd(phydev, MDIO_MMD_AN, MDIO_CTRL1);
+		ret = phy_read_mmd(phydev, MDIO_MMD_AN, reg);
 		if (ret < 0)
 			return ret;
 
@@ -242,7 +365,13 @@ EXPORT_SYMBOL_GPL(genphy_c45_check_and_restart_aneg);
  */
 int genphy_c45_aneg_done(struct phy_device *phydev)
 {
-	int val = phy_read_mmd(phydev, MDIO_MMD_AN, MDIO_STAT1);
+	int reg = MDIO_STAT1;
+	int val;
+
+	if (genphy_c45_baset1_able(phydev))
+		reg = MDIO_AN_T1_STAT;
+
+	val = phy_read_mmd(phydev, MDIO_MMD_AN, reg);
 
 	return val < 0 ? val : val & MDIO_AN_STAT1_COMPLETE ? 1 : 0;
 }
@@ -307,6 +436,49 @@ int genphy_c45_read_link(struct phy_device *phydev)
 }
 EXPORT_SYMBOL_GPL(genphy_c45_read_link);
 
+/* Read the Clause 45 defined BASE-T1 AN (7.513) status register to check
+ * if autoneg is complete. If so read the BASE-T1 Autonegotiation
+ * Advertisement registers filling in the link partner advertisement,
+ * pause and asym_pause members in phydev.
+ */
+static int genphy_c45_baset1_read_lpa(struct phy_device *phydev)
+{
+	int val;
+
+	val = phy_read_mmd(phydev, MDIO_MMD_AN, MDIO_AN_T1_STAT);
+	if (val < 0)
+		return val;
+
+	if (!(val & MDIO_AN_STAT1_COMPLETE)) {
+		linkmode_clear_bit(ETHTOOL_LINK_MODE_Autoneg_BIT, phydev->lp_advertising);
+		mii_t1_adv_l_mod_linkmode_t(phydev->lp_advertising, 0);
+		mii_t1_adv_m_mod_linkmode_t(phydev->lp_advertising, 0);
+
+		phydev->pause = 0;
+		phydev->asym_pause = 0;
+
+		return 0;
+	}
+
+	linkmode_mod_bit(ETHTOOL_LINK_MODE_Autoneg_BIT, phydev->lp_advertising, 1);
+
+	val = phy_read_mmd(phydev, MDIO_MMD_AN, MDIO_AN_T1_LP_L);
+	if (val < 0)
+		return val;
+
+	mii_t1_adv_l_mod_linkmode_t(phydev->lp_advertising, val);
+	phydev->pause = val & MDIO_AN_T1_ADV_L_PAUSE_CAP ? 1 : 0;
+	phydev->asym_pause = val & MDIO_AN_T1_ADV_L_PAUSE_ASYM ? 1 : 0;
+
+	val = phy_read_mmd(phydev, MDIO_MMD_AN, MDIO_AN_T1_LP_M);
+	if (val < 0)
+		return val;
+
+	mii_t1_adv_m_mod_linkmode_t(phydev->lp_advertising, val);
+
+	return 0;
+}
+
 /**
  * genphy_c45_read_lpa - read the link partner advertisement and pause
  * @phydev: target phy_device struct
@@ -321,6 +493,9 @@ int genphy_c45_read_lpa(struct phy_device *phydev)
 {
 	int val;
 
+	if (genphy_c45_baset1_able(phydev))
+		return genphy_c45_baset1_read_lpa(phydev);
+
 	val = phy_read_mmd(phydev, MDIO_MMD_AN, MDIO_STAT1);
 	if (val < 0)
 		return val;
@@ -399,6 +574,17 @@ int genphy_c45_read_pma(struct phy_device *phydev)
 
 	phydev->duplex = DUPLEX_FULL;
 
+	if (genphy_c45_baset1_able(phydev)) {
+		val = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, MDIO_PMA_PMD_BT1_CTRL);
+		if (val < 0)
+			return val;
+
+		if (MDIO_PMA_PMD_BT1_CTRL_CFG_MST)
+			phydev->master_slave_state = MASTER_SLAVE_STATE_MASTER;
+		else
+			phydev->master_slave_state = MASTER_SLAVE_STATE_SLAVE;
+	}
+
 	return 0;
 }
 EXPORT_SYMBOL_GPL(genphy_c45_read_pma);
@@ -530,12 +716,67 @@ int genphy_c45_pma_read_abilities(struct phy_device *phydev)
 					 phydev->supported,
 					 val & MDIO_PMA_NG_EXTABLE_5GBT);
 		}
+
+		if (val & MDIO_PMA_EXTABLE_BT1) {
+			val = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, MDIO_PMA_PMD_BT1);
+			if (val < 0)
+				return val;
+
+			linkmode_mod_bit(ETHTOOL_LINK_MODE_10baseT1L_Full_BIT,
+					 phydev->supported,
+					 val & MDIO_PMA_PMD_BT1_B10L_ABLE);
+
+			val = phy_read_mmd(phydev, MDIO_MMD_AN, MDIO_AN_T1_STAT);
+			if (val < 0)
+				return val;
+
+			linkmode_mod_bit(ETHTOOL_LINK_MODE_Autoneg_BIT,
+					 phydev->supported,
+					 val & MDIO_AN_STAT1_ABLE);
+		}
 	}
 
 	return 0;
 }
 EXPORT_SYMBOL_GPL(genphy_c45_pma_read_abilities);
 
+/* Read master/slave preference from registers.
+ * The preference is read from the BIT(4) of BASE-T1 AN
+ * advertisement register 7.515 and whether the preference
+ * is forced or not, it is read from BASE-T1 AN advertisement
+ * register 7.514.
+ */
+static int genphy_c45_baset1_read_status(struct phy_device *phydev)
+{
+	int ret;
+	int cfg;
+
+	phydev->master_slave_get = MASTER_SLAVE_CFG_UNKNOWN;
+	phydev->master_slave_state = MASTER_SLAVE_STATE_UNKNOWN;
+
+	ret = phy_read_mmd(phydev, MDIO_MMD_AN, MDIO_AN_T1_ADV_L);
+	if (ret < 0)
+		return ret;
+
+	cfg = phy_read_mmd(phydev, MDIO_MMD_AN, MDIO_AN_T1_ADV_M);
+	if (cfg < 0)
+		return cfg;
+
+	if (ret & MDIO_AN_T1_ADV_L_FORCE_MS) {
+		if (cfg & MDIO_AN_T1_ADV_M_MST)
+			phydev->master_slave_get = MASTER_SLAVE_CFG_MASTER_FORCE;
+		else
+			phydev->master_slave_get = MASTER_SLAVE_CFG_SLAVE_FORCE;
+	} else {
+		if (cfg & MDIO_AN_T1_ADV_M_MST)
+			phydev->master_slave_get = MASTER_SLAVE_CFG_MASTER_PREFERRED;
+		else
+			phydev->master_slave_get = MASTER_SLAVE_CFG_SLAVE_PREFERRED;
+	}
+
+	return 0;
+}
+
 /**
  * genphy_c45_read_status - read PHY status
  * @phydev: target phy_device struct
@@ -560,6 +801,12 @@ int genphy_c45_read_status(struct phy_device *phydev)
 		if (ret)
 			return ret;
 
+		if (genphy_c45_baset1_able(phydev)) {
+			ret = genphy_c45_baset1_read_status(phydev);
+			if (ret < 0)
+				return ret;
+		}
+
 		phy_resolve_aneg_linkmode(phydev);
 	} else {
 		ret = genphy_c45_read_pma(phydev);
diff --git a/drivers/net/phy/phy-core.c b/drivers/net/phy/phy-core.c
index 2001f3329133..1f2531a1a876 100644
--- a/drivers/net/phy/phy-core.c
+++ b/drivers/net/phy/phy-core.c
@@ -13,7 +13,7 @@
  */
 const char *phy_speed_to_str(int speed)
 {
-	BUILD_BUG_ON_MSG(__ETHTOOL_LINK_MODE_MASK_NBITS != 92,
+	BUILD_BUG_ON_MSG(__ETHTOOL_LINK_MODE_MASK_NBITS != 93,
 		"Enum ethtool_link_mode_bit_indices and phylib are out of sync. "
 		"If a speed or mode has been added please update phy_speed_to_str "
 		"and the PHY settings array.\n");
@@ -176,6 +176,7 @@ static const struct phy_setting settings[] = {
 	/* 10M */
 	PHY_SETTING(     10, FULL,     10baseT_Full		),
 	PHY_SETTING(     10, HALF,     10baseT_Half		),
+	PHY_SETTING(     10, FULL,     10baseT1L_Full		),
 };
 #undef PHY_SETTING
 
diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
index f867042b2eb4..431a8719c635 100644
--- a/drivers/net/phy/phy_device.c
+++ b/drivers/net/phy/phy_device.c
@@ -90,8 +90,9 @@ const int phy_10_100_features_array[4] = {
 };
 EXPORT_SYMBOL_GPL(phy_10_100_features_array);
 
-const int phy_basic_t1_features_array[2] = {
+const int phy_basic_t1_features_array[3] = {
 	ETHTOOL_LINK_MODE_TP_BIT,
+	ETHTOOL_LINK_MODE_10baseT1L_Full_BIT,
 	ETHTOOL_LINK_MODE_100baseT1_Full_BIT,
 };
 EXPORT_SYMBOL_GPL(phy_basic_t1_features_array);
@@ -599,6 +600,7 @@ struct phy_device *phy_device_create(struct mii_bus *bus, int addr, u32 phy_id,
 
 	dev->autoneg = AUTONEG_ENABLE;
 
+	dev->pma_extable = -ENODATA;
 	dev->is_c45 = is_c45;
 	dev->phy_id = phy_id;
 	if (c45_ids)
diff --git a/drivers/net/phy/phylink.c b/drivers/net/phy/phylink.c
index 33c285252584..d707604d1d5a 100644
--- a/drivers/net/phy/phylink.c
+++ b/drivers/net/phy/phylink.c
@@ -168,8 +168,10 @@ static void phylink_caps_to_linkmodes(unsigned long *linkmodes,
 	if (caps & MAC_10HD)
 		__set_bit(ETHTOOL_LINK_MODE_10baseT_Half_BIT, linkmodes);
 
-	if (caps & MAC_10FD)
+	if (caps & MAC_10FD) {
 		__set_bit(ETHTOOL_LINK_MODE_10baseT_Full_BIT, linkmodes);
+		__set_bit(ETHTOOL_LINK_MODE_10baseT1L_Full_BIT, linkmodes);
+	}
 
 	if (caps & MAC_100HD) {
 		__set_bit(ETHTOOL_LINK_MODE_100baseT_Half_BIT, linkmodes);
diff --git a/include/linux/mdio.h b/include/linux/mdio.h
index ecac96d52e01..00177567cfef 100644
--- a/include/linux/mdio.h
+++ b/include/linux/mdio.h
@@ -340,6 +340,76 @@ static inline void mii_10gbt_stat_mod_linkmode_lpa_t(unsigned long *advertising,
 			 advertising, lpa & MDIO_AN_10GBT_STAT_LP10G);
 }
 
+/**
+ * mii_t1_adv_l_mod_linkmode_t
+ * @advertising: target the linkmode advertisement settings
+ * @lpa: value of the BASE-T1 Autonegotiation Advertisement [15:0] Register
+ *
+ * A small helper function that translates BASE-T1 Autonegotiation
+ * Advertisement [15:0] Register bits to linkmode advertisement settings.
+ * Other bits in advertising aren't changed.
+ */
+static inline void mii_t1_adv_l_mod_linkmode_t(unsigned long *advertising, u32 lpa)
+{
+	linkmode_mod_bit(ETHTOOL_LINK_MODE_Pause_BIT, advertising,
+			 lpa & MDIO_AN_T1_ADV_L_PAUSE_CAP);
+	linkmode_mod_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT, advertising,
+			 lpa & MDIO_AN_T1_ADV_L_PAUSE_ASYM);
+}
+
+/**
+ * mii_t1_adv_m_mod_linkmode_t
+ * @advertising: target the linkmode advertisement settings
+ * @lpa: value of the BASE-T1 Autonegotiation Advertisement [31:16] Register
+ *
+ * A small helper function that translates BASE-T1 Autonegotiation
+ * Advertisement [31:16] Register bits to linkmode advertisement settings.
+ * Other bits in advertising aren't changed.
+ */
+static inline void mii_t1_adv_m_mod_linkmode_t(unsigned long *advertising, u32 lpa)
+{
+	linkmode_mod_bit(ETHTOOL_LINK_MODE_10baseT1L_Full_BIT,
+			 advertising, lpa & MDIO_AN_T1_ADV_M_B10L);
+}
+
+/**
+ * linkmode_adv_to_mii_t1_adv_l_t
+ * @advertising: the linkmode advertisement settings
+ *
+ * A small helper function that translates linkmode advertisement
+ * settings to phy autonegotiation advertisements for the
+ * BASE-T1 Autonegotiation Advertisement [15:0] Register.
+ */
+static inline u32 linkmode_adv_to_mii_t1_adv_l_t(unsigned long *advertising)
+{
+	u32 result = 0;
+
+	if (linkmode_test_bit(ETHTOOL_LINK_MODE_Pause_BIT, advertising))
+		result |= MDIO_AN_T1_ADV_L_PAUSE_CAP;
+	if (linkmode_test_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT, advertising))
+		result |= MDIO_AN_T1_ADV_L_PAUSE_ASYM;
+
+	return result;
+}
+
+/**
+ * linkmode_adv_to_mii_t1_adv_m_t
+ * @advertising: the linkmode advertisement settings
+ *
+ * A small helper function that translates linkmode advertisement
+ * settings to phy autonegotiation advertisements for the
+ * BASE-T1 Autonegotiation Advertisement [31:16] Register.
+ */
+static inline u32 linkmode_adv_to_mii_t1_adv_m_t(unsigned long *advertising)
+{
+	u32 result = 0;
+
+	if (linkmode_test_bit(ETHTOOL_LINK_MODE_10baseT1L_Full_BIT, advertising))
+		result |= MDIO_AN_T1_ADV_M_B10L;
+
+	return result;
+}
+
 int __mdiobus_read(struct mii_bus *bus, int addr, u32 regnum);
 int __mdiobus_write(struct mii_bus *bus, int addr, u32 regnum, u16 val);
 int __mdiobus_modify_changed(struct mii_bus *bus, int addr, u32 regnum,
diff --git a/include/linux/phy.h b/include/linux/phy.h
index 36ca2b5c2253..2d12054932ba 100644
--- a/include/linux/phy.h
+++ b/include/linux/phy.h
@@ -65,7 +65,7 @@ extern const int phy_basic_ports_array[3];
 extern const int phy_fibre_port_array[1];
 extern const int phy_all_ports_features_array[7];
 extern const int phy_10_100_features_array[4];
-extern const int phy_basic_t1_features_array[2];
+extern const int phy_basic_t1_features_array[3];
 extern const int phy_gbit_features_array[2];
 extern const int phy_10gbit_features_array[1];
 
@@ -570,6 +570,7 @@ struct macsec_ops;
  * @autoneg_complete: Flag auto negotiation of the link has completed
  * @mdix: Current crossover
  * @mdix_ctrl: User setting of crossover
+ * @pma_extable: Cached value of PMA/PMD Extended Abilities Register
  * @interrupts: Flag interrupts have been enabled
  * @interface: enum phy_interface_t value
  * @skb: Netlink message for cable diagnostics
@@ -698,6 +699,8 @@ struct phy_device {
 	u8 mdix;
 	u8 mdix_ctrl;
 
+	int pma_extable;
+
 	void (*phy_link_change)(struct phy_device *phydev, bool up);
 	void (*adjust_link)(struct net_device *dev);
 
diff --git a/include/uapi/linux/ethtool.h b/include/uapi/linux/ethtool.h
index 7bc4b8def12c..e0f0ee9bc89e 100644
--- a/include/uapi/linux/ethtool.h
+++ b/include/uapi/linux/ethtool.h
@@ -1691,6 +1691,7 @@ enum ethtool_link_mode_bit_indices {
 	ETHTOOL_LINK_MODE_400000baseCR4_Full_BIT	 = 89,
 	ETHTOOL_LINK_MODE_100baseFX_Half_BIT		 = 90,
 	ETHTOOL_LINK_MODE_100baseFX_Full_BIT		 = 91,
+	ETHTOOL_LINK_MODE_10baseT1L_Full_BIT		 = 92,
 	/* must be last entry */
 	__ETHTOOL_LINK_MODE_MASK_NBITS
 };
diff --git a/include/uapi/linux/mdio.h b/include/uapi/linux/mdio.h
index c54e6eae5366..75b7257a51e1 100644
--- a/include/uapi/linux/mdio.h
+++ b/include/uapi/linux/mdio.h
@@ -67,6 +67,19 @@
 #define MDIO_PCS_10GBRT_STAT2	33	/* 10GBASE-R/-T PCS status 2 */
 #define MDIO_AN_10GBT_CTRL	32	/* 10GBASE-T auto-negotiation control */
 #define MDIO_AN_10GBT_STAT	33	/* 10GBASE-T auto-negotiation status */
+#define MDIO_B10L_PMA_CTRL	2294	/* 10BASE-T1L PMA control */
+#define MDIO_PMA_10T1L_STAT	2295	/* 10BASE-T1L PMA status */
+#define MDIO_PCS_10T1L_CTRL	2278	/* 10BASE-T1L PCS control */
+#define MDIO_PMA_PMD_BT1	18	/* BASE-T1 PMA/PMD extended ability */
+#define MDIO_AN_T1_CTRL		512	/* BASE-T1 AN control */
+#define MDIO_AN_T1_STAT		513	/* BASE-T1 AN status */
+#define MDIO_AN_T1_ADV_L	514	/* BASE-T1 AN advertisement register [15:0] */
+#define MDIO_AN_T1_ADV_M	515	/* BASE-T1 AN advertisement register [31:16] */
+#define MDIO_AN_T1_ADV_H	516	/* BASE-T1 AN advertisement register [47:32] */
+#define MDIO_AN_T1_LP_L		517	/* BASE-T1 AN LP Base Page ability register [15:0] */
+#define MDIO_AN_T1_LP_M		518	/* BASE-T1 AN LP Base Page ability register [31:16] */
+#define MDIO_AN_T1_LP_H		519	/* BASE-T1 AN LP Base Page ability register [47:32] */
+#define MDIO_PMA_PMD_BT1_CTRL	2100	/* BASE-T1 PMA/PMD control register */
 
 /* LASI (Link Alarm Status Interrupt) registers, defined by XENPAK MSA. */
 #define MDIO_PMA_LASI_RXCTRL	0x9000	/* RX_ALARM control */
@@ -159,6 +172,7 @@
 #define MDIO_PMA_CTRL2_10BT		0x000f	/* 10BASE-T type */
 #define MDIO_PMA_CTRL2_2_5GBT		0x0030  /* 2.5GBaseT type */
 #define MDIO_PMA_CTRL2_5GBT		0x0031  /* 5GBaseT type */
+#define MDIO_PMA_CTRL2_BASET1		0x003D  /* BASE-T1 type */
 #define MDIO_PCS_CTRL2_TYPE		0x0003	/* PCS type selection */
 #define MDIO_PCS_CTRL2_10GBR		0x0000	/* 10GBASE-R type */
 #define MDIO_PCS_CTRL2_10GBX		0x0001	/* 10GBASE-X type */
@@ -212,6 +226,7 @@
 #define MDIO_PMA_EXTABLE_1000BKX	0x0040	/* 1000BASE-KX ability */
 #define MDIO_PMA_EXTABLE_100BTX		0x0080	/* 100BASE-TX ability */
 #define MDIO_PMA_EXTABLE_10BT		0x0100	/* 10BASE-T ability */
+#define MDIO_PMA_EXTABLE_BT1		0x0800	/* BASE-T1 ability */
 #define MDIO_PMA_EXTABLE_NBT		0x4000  /* 2.5/5GBASE-T ability */
 
 /* PHY XGXS lane state register. */
@@ -268,6 +283,66 @@
 #define MDIO_AN_10GBT_STAT_MS		0x4000	/* Master/slave config */
 #define MDIO_AN_10GBT_STAT_MSFLT	0x8000	/* Master/slave config fault */
 
+/* 10BASE-T1L PMA control */
+#define MDIO_PMA_10T1L_CTRL_LB_EN	0x0001	/* Enable loopback mode */
+#define MDIO_PMA_10T1L_CTRL_EEE_EN	0x0400	/* Enable EEE mode */
+#define MDIO_PMA_10T1L_CTRL_LOW_POWER	0x0800	/* Low-power mode */
+#define MDIO_PMA_10T1L_CTRL_2V4_EN	0x1000	/* Enable 2.4 Vpp operating mode */
+#define MDIO_PMA_10T1L_CTRL_TX_DIS	0x4000	/* Transmit disable */
+#define MDIO_PMA_10T1L_CTRL_PMA_RST	0x8000	/* MA reset */
+
+/* 10BASE-T1L PMA status register. */
+#define MDIO_PMA_10T1L_STAT_LINK	0x0001	/* PMA receive link up */
+#define MDIO_PMA_10T1L_STAT_FAULT	0x0002	/* Fault condition detected */
+#define MDIO_PMA_10T1L_STAT_POLARITY	0x0004	/* Receive polarity is reversed */
+#define MDIO_PMA_10T1L_STAT_RECV_FAULT	0x0200	/* Able to detect fault on receive path */
+#define MDIO_PMA_10T1L_STAT_EEE		0x0400	/* PHY has EEE ability */
+#define MDIO_PMA_10T1L_STAT_LOW_POWER	0x0800	/* PMA has low-power ability */
+#define MDIO_PMA_10T1L_STAT_2V4_ABLE	0x1000	/* PHY has 2.4 Vpp operating mode ability */
+#define MDIO_PMA_10T1L_STAT_LB_ABLE	0x2000	/* PHY has loopback ability */
+
+/* 10BASE-T1L PCS control register. */
+#define MDIO_PCS_10T1L_CTRL_LB		0x4000	/* Enable PCS level loopback mode */
+#define MDIO_PCS_10T1L_CTRL_RESET	0x8000	/* PCS reset */
+
+/* BASE-T1 PMA/PMD extended ability register. */
+#define MDIO_PMA_PMD_BT1_B10L_ABLE	0x0004	/* 10BASE-T1L Ability */
+
+/* BASE-T1 auto-negotiation advertisement register [15:0] */
+#define MDIO_AN_T1_ADV_L_PAUSE_CAP	ADVERTISE_PAUSE_CAP
+#define MDIO_AN_T1_ADV_L_PAUSE_ASYM	ADVERTISE_PAUSE_ASYM
+#define MDIO_AN_T1_ADV_L_FORCE_MS	0x1000	/* Force Master/slave Configuration */
+#define MDIO_AN_T1_ADV_L_REMOTE_FAULT	ADVERTISE_RFAULT
+#define MDIO_AN_T1_ADV_L_ACK		ADVERTISE_LPACK
+#define MDIO_AN_T1_ADV_L_NEXT_PAGE_REQ	ADVERTISE_NPAGE
+
+/* BASE-T1 auto-negotiation advertisement register [31:16] */
+#define MDIO_AN_T1_ADV_M_B10L		0x4000	/* device is compatible with 10BASE-T1L */
+#define MDIO_AN_T1_ADV_M_MST		0x0010	/* advertise master preference */
+
+/* BASE-T1 auto-negotiation advertisement register [47:32] */
+#define MDIO_AN_T1_ADV_H_10L_TX_HI_REQ	0x1000	/* 10BASE-T1L High Level Transmit Request */
+#define MDIO_AN_T1_ADV_H_10L_TX_HI	0x2000	/* 10BASE-T1L High Level Transmit Ability */
+
+/* BASE-T1 AN LP Base Page ability register [15:0] */
+#define MDIO_AN_T1_LP_L_PAUSE_CAP	LPA_PAUSE_CAP
+#define MDIO_AN_T1_LP_L_PAUSE_ASYM	LPA_PAUSE_ASYM
+#define MDIO_AN_T1_LP_L_FORCE_MS	0x1000	/* LP Force Master/slave Configuration */
+#define MDIO_AN_T1_LP_L_REMOTE_FAULT	LPA_RFAULT
+#define MDIO_AN_T1_LP_L_ACK		LPA_LPACK
+#define MDIO_AN_T1_LP_L_NEXT_PAGE_REQ	LPA_NPAGE
+
+/* BASE-T1 AN LP Base Page ability register [31:16] */
+#define MDIO_AN_T1_LP_M_MST		0x0010	/* LP master preference */
+#define MDIO_AN_T1_LP_M_B10L		0x4000	/* LP is compatible with 10BASE-T1L */
+
+/* BASE-T1 AN LP Base Page ability register [47:32] */
+#define MDIO_AN_T1_LP_H_10L_TX_HI_REQ	0x1000	/* 10BASE-T1L High Level LP Transmit Request */
+#define MDIO_AN_T1_LP_H_10L_TX_HI	0x2000	/* 10BASE-T1L High Level LP Transmit Ability */
+
+/* BASE-T1 PMA/PMD control register */
+#define MDIO_PMA_PMD_BT1_CTRL_CFG_MST	0x4000 /* MASTER-SLAVE config value */
+
 /* EEE Supported/Advertisement/LP Advertisement registers.
  *
  * EEE capability Register (3.20), Advertisement (7.60) and
diff --git a/net/ethtool/common.c b/net/ethtool/common.c
index 0c5210015911..566adf85e658 100644
--- a/net/ethtool/common.c
+++ b/net/ethtool/common.c
@@ -201,6 +201,7 @@ const char link_mode_names[][ETH_GSTRING_LEN] = {
 	__DEFINE_LINK_MODE_NAME(400000, CR4, Full),
 	__DEFINE_LINK_MODE_NAME(100, FX, Half),
 	__DEFINE_LINK_MODE_NAME(100, FX, Full),
+	__DEFINE_LINK_MODE_NAME(10, T1L, Full),
 };
 static_assert(ARRAY_SIZE(link_mode_names) == __ETHTOOL_LINK_MODE_MASK_NBITS);
 
@@ -236,6 +237,7 @@ static_assert(ARRAY_SIZE(link_mode_names) == __ETHTOOL_LINK_MODE_MASK_NBITS);
 #define __LINK_MODE_LANES_T1		1
 #define __LINK_MODE_LANES_X		1
 #define __LINK_MODE_LANES_FX		1
+#define __LINK_MODE_LANES_T1L		1
 
 #define __DEFINE_LINK_MODE_PARAMS(_speed, _type, _duplex)	\
 	[ETHTOOL_LINK_MODE(_speed, _type, _duplex)] = {		\
@@ -349,6 +351,7 @@ const struct link_mode_info link_mode_params[] = {
 	__DEFINE_LINK_MODE_PARAMS(400000, CR4, Full),
 	__DEFINE_LINK_MODE_PARAMS(100, FX, Half),
 	__DEFINE_LINK_MODE_PARAMS(100, FX, Full),
+	__DEFINE_LINK_MODE_PARAMS(10, T1L, Full),
 };
 static_assert(ARRAY_SIZE(link_mode_params) == __ETHTOOL_LINK_MODE_MASK_NBITS);