diff options
author | Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> | 2020-09-04 22:18:33 +0200 |
---|---|---|
committer | Mauro Carvalho Chehab <mchehab+huawei@kernel.org> | 2020-09-10 14:23:28 +0200 |
commit | 311a6408f8d46d47e35d3bf598dced39af4ce087 (patch) | |
tree | a6c36c68f581355aadaf937c0fe4a22a9588b585 | |
parent | 576f5d4ba8f672953513280510abf9a736b015cc (diff) | |
download | linux-311a6408f8d46d47e35d3bf598dced39af4ce087.tar.bz2 |
media: i2c: ov5640: Configure HVP lines in s_power callback
Configure HVP lines in s_power callback instead of configuring everytime
in ov5640_set_stream_dvp().
Alongside also disable MIPI in DVP mode.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
-rw-r--r-- | drivers/media/i2c/ov5640.c | 123 |
1 files changed, 58 insertions, 65 deletions
diff --git a/drivers/media/i2c/ov5640.c b/drivers/media/i2c/ov5640.c index 905dd707e602..19284ae26f06 100644 --- a/drivers/media/i2c/ov5640.c +++ b/drivers/media/i2c/ov5640.c @@ -1217,71 +1217,6 @@ static int ov5640_set_autogain(struct ov5640_dev *sensor, bool on) static int ov5640_set_stream_dvp(struct ov5640_dev *sensor, bool on) { - int ret; - unsigned int flags = sensor->ep.bus.parallel.flags; - u8 pclk_pol = 0; - u8 hsync_pol = 0; - u8 vsync_pol = 0; - - /* - * Note about parallel port configuration. - * - * When configured in parallel mode, the OV5640 will - * output 10 bits data on DVP data lines [9:0]. - * If only 8 bits data are wanted, the 8 bits data lines - * of the camera interface must be physically connected - * on the DVP data lines [9:2]. - * - * Control lines polarity can be configured through - * devicetree endpoint control lines properties. - * If no endpoint control lines properties are set, - * polarity will be as below: - * - VSYNC: active high - * - HREF: active low - * - PCLK: active low - */ - - if (on) { - /* - * configure parallel port control lines polarity - * - * POLARITY CTRL0 - * - [5]: PCLK polarity (0: active low, 1: active high) - * - [1]: HREF polarity (0: active low, 1: active high) - * - [0]: VSYNC polarity (mismatch here between - * datasheet and hardware, 0 is active high - * and 1 is active low...) - */ - if (flags & V4L2_MBUS_PCLK_SAMPLE_RISING) - pclk_pol = 1; - if (flags & V4L2_MBUS_HSYNC_ACTIVE_HIGH) - hsync_pol = 1; - if (flags & V4L2_MBUS_VSYNC_ACTIVE_LOW) - vsync_pol = 1; - - ret = ov5640_write_reg(sensor, - OV5640_REG_POLARITY_CTRL00, - (pclk_pol << 5) | - (hsync_pol << 1) | - vsync_pol); - - if (ret) - return ret; - } - - /* - * powerdown MIPI TX/RX PHY & disable MIPI - * - * MIPI CONTROL 00 - * 4: PWDN PHY TX - * 3: PWDN PHY RX - * 2: MIPI enable - */ - ret = ov5640_write_reg(sensor, - OV5640_REG_IO_MIPI_CTRL00, on ? 0x18 : 0); - if (ret) - return ret; - return ov5640_write_reg(sensor, OV5640_REG_SYS_CTRL0, on ? OV5640_REG_SYS_CTRL0_SW_PWUP : OV5640_REG_SYS_CTRL0_SW_PWDN); @@ -2043,16 +1978,74 @@ static int ov5640_set_power_mipi(struct ov5640_dev *sensor, bool on) static int ov5640_set_power_dvp(struct ov5640_dev *sensor, bool on) { + unsigned int flags = sensor->ep.bus.parallel.flags; + u8 pclk_pol = 0; + u8 hsync_pol = 0; + u8 vsync_pol = 0; int ret; if (!on) { /* Reset settings to their default values. */ + ov5640_write_reg(sensor, OV5640_REG_IO_MIPI_CTRL00, 0x58); + ov5640_write_reg(sensor, OV5640_REG_POLARITY_CTRL00, 0x20); ov5640_write_reg(sensor, OV5640_REG_PAD_OUTPUT_ENABLE01, 0x00); ov5640_write_reg(sensor, OV5640_REG_PAD_OUTPUT_ENABLE02, 0x00); return 0; } /* + * Note about parallel port configuration. + * + * When configured in parallel mode, the OV5640 will + * output 10 bits data on DVP data lines [9:0]. + * If only 8 bits data are wanted, the 8 bits data lines + * of the camera interface must be physically connected + * on the DVP data lines [9:2]. + * + * Control lines polarity can be configured through + * devicetree endpoint control lines properties. + * If no endpoint control lines properties are set, + * polarity will be as below: + * - VSYNC: active high + * - HREF: active low + * - PCLK: active low + */ + /* + * configure parallel port control lines polarity + * + * POLARITY CTRL0 + * - [5]: PCLK polarity (0: active low, 1: active high) + * - [1]: HREF polarity (0: active low, 1: active high) + * - [0]: VSYNC polarity (mismatch here between + * datasheet and hardware, 0 is active high + * and 1 is active low...) + */ + if (flags & V4L2_MBUS_PCLK_SAMPLE_RISING) + pclk_pol = 1; + if (flags & V4L2_MBUS_HSYNC_ACTIVE_HIGH) + hsync_pol = 1; + if (flags & V4L2_MBUS_VSYNC_ACTIVE_LOW) + vsync_pol = 1; + + ret = ov5640_write_reg(sensor, OV5640_REG_POLARITY_CTRL00, + (pclk_pol << 5) | (hsync_pol << 1) | vsync_pol); + + if (ret) + return ret; + + /* + * powerdown MIPI TX/RX PHY & disable MIPI + * + * MIPI CONTROL 00 + * 4: PWDN PHY TX + * 3: PWDN PHY RX + * 2: MIPI enable + */ + ret = ov5640_write_reg(sensor, OV5640_REG_IO_MIPI_CTRL00, 0x18); + if (ret) + return ret; + + /* * enable VSYNC/HREF/PCLK DVP control lines * & D[9:6] DVP data lines * |