Merge master.kernel.org:/home/rmk/linux-2.6-arm

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] Fix PCI_DMA_BUS_IS_PHYS for ARM
  [ARM] 5247/1: tosa: SW_EAR_IN support
  [ARM] 5246/1: tosa: add proper clock alias for tc6393xb clock
  [ARM] 5245/1: Fix warning about unused return value in drivers/pcmcia
  [ARM] OMAP: Fix MMC device data
  imx serial: fix rts handling for non imx1 based hardware
  imx serial: set RXD mux bit on i.MX27 and i.MX31
  i.MX serial: fix init failure
  pcm037: add rts/cts support for serial port

6 files changed, 131 insertions, 40 deletions

diff --git a/arch/arm/include/asm/pci.h b/arch/arm/include/asm/pci.h
index 721c03d53f4b..918d0cbbf064 100644
--- a/arch/arm/include/asm/pci.h
+++ b/arch/arm/include/asm/pci.h
@@ -30,7 +30,7 @@ static inline void pcibios_penalize_isa_irq(int irq, int active)
  * The networking and block device layers use this boolean for bounce
  * buffer decisions.
  */
-#define PCI_DMA_BUS_IS_PHYS     (0)
+#define PCI_DMA_BUS_IS_PHYS     (1)
 
 /*
  * Whether pci_unmap_{single,page} is a nop depends upon the
diff --git a/arch/arm/mach-mx3/pcm037.c b/arch/arm/mach-mx3/pcm037.c
index 0a152ed15a85..df8582a6231b 100644
--- a/arch/arm/mach-mx3/pcm037.c
+++ b/arch/arm/mach-mx3/pcm037.c
@@ -54,7 +54,7 @@ static struct platform_device pcm037_flash = {
 };
 
 static struct imxuart_platform_data uart_pdata = {
-	.flags = 0,
+	.flags = IMXUART_HAVE_RTSCTS,
 };
 
 static struct platform_device *devices[] __initdata = {
diff --git a/arch/arm/mach-pxa/tosa.c b/arch/arm/mach-pxa/tosa.c
index 5dab30eafddc..9f3ef9eb32e3 100644
--- a/arch/arm/mach-pxa/tosa.c
+++ b/arch/arm/mach-pxa/tosa.c
@@ -50,6 +50,7 @@
 #include <asm/mach/sharpsl_param.h>
 
 #include "generic.h"
+#include "clock.h"
 #include "devices.h"
 
 static unsigned long tosa_pin_config[] = {
@@ -521,6 +522,14 @@ static struct gpio_keys_button tosa_gpio_keys[] = {
 		.wakeup	= 1,
 		.active_low = 1,
 	},
+	{
+		.type	= EV_SW,
+		.code	= SW_HEADPHONE_INSERT,
+		.gpio	= TOSA_GPIO_EAR_IN,
+		.desc	= "HeadPhone insert",
+		.active_low = 1,
+		.debounce_interval = 300,
+	},
 };
 
 static struct gpio_keys_platform_data tosa_gpio_keys_platform_data = {
@@ -792,6 +801,8 @@ static void __init tosa_init(void)
 	pxa_set_i2c_info(NULL);
 	platform_scoop_config = &tosa_pcmcia_config;
 
+	clk_add_alias("CLK_CK3P6MI", &tc6393xb_device.dev, "GPIO11_CLK", NULL);
+
 	platform_add_devices(devices, ARRAY_SIZE(devices));
 }
 
diff --git a/arch/arm/plat-omap/devices.c b/arch/arm/plat-omap/devices.c
index 187e3d8bfdfe..bc1cf30c83e0 100644
--- a/arch/arm/plat-omap/devices.c
+++ b/arch/arm/plat-omap/devices.c
@@ -21,6 +21,7 @@
 
 #include <mach/tc.h>
 #include <mach/board.h>
+#include <mach/mmc.h>
 #include <mach/mux.h>
 #include <mach/gpio.h>
 #include <mach/menelaus.h>
@@ -194,25 +195,38 @@ void omap_mcbsp_register_board_cfg(struct omap_mcbsp_platform_data *config,
 
 /*-------------------------------------------------------------------------*/
 
-#if	defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE)
+#if	defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE) || \
+	defined(CONFIG_MMC_OMAP_HS) || defined(CONFIG_MMC_OMAP_HS_MODULE)
 
-#ifdef CONFIG_ARCH_OMAP24XX
+#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX)
 #define	OMAP_MMC1_BASE		0x4809c000
-#define OMAP_MMC1_INT		INT_24XX_MMC_IRQ
+#define	OMAP_MMC1_END		(OMAP_MMC1_BASE + 0x1fc)
+#define	OMAP_MMC1_INT		INT_24XX_MMC_IRQ
+
+#define	OMAP_MMC2_BASE		0x480b4000
+#define	OMAP_MMC2_END		(OMAP_MMC2_BASE + 0x1fc)
+#define	OMAP_MMC2_INT		INT_24XX_MMC2_IRQ
+
 #else
+
 #define	OMAP_MMC1_BASE		0xfffb7800
+#define	OMAP_MMC1_END		(OMAP_MMC1_BASE + 0x7f)
 #define OMAP_MMC1_INT		INT_MMC
-#endif
+
 #define	OMAP_MMC2_BASE		0xfffb7c00	/* omap16xx only */
+#define	OMAP_MMC2_END		(OMAP_MMC2_BASE + 0x7f)
+#define	OMAP_MMC2_INT		INT_1610_MMC2
 
-static struct omap_mmc_conf mmc1_conf;
+#endif
+
+static struct omap_mmc_platform_data mmc1_data;
 
 static u64 mmc1_dmamask = 0xffffffff;
 
 static struct resource mmc1_resources[] = {
 	{
 		.start		= OMAP_MMC1_BASE,
-		.end		= OMAP_MMC1_BASE + 0x7f,
+		.end		= OMAP_MMC1_END,
 		.flags		= IORESOURCE_MEM,
 	},
 	{
@@ -226,26 +240,27 @@ static struct platform_device mmc_omap_device1 = {
 	.id		= 1,
 	.dev = {
 		.dma_mask	= &mmc1_dmamask,
-		.platform_data	= &mmc1_conf,
+		.platform_data	= &mmc1_data,
 	},
 	.num_resources	= ARRAY_SIZE(mmc1_resources),
 	.resource	= mmc1_resources,
 };
 
-#ifdef	CONFIG_ARCH_OMAP16XX
+#if defined(CONFIG_ARCH_OMAP16XX) || defined(CONFIG_ARCH_OMAP2430) || \
+	defined(CONFIG_ARCH_OMAP34XX)
 
-static struct omap_mmc_conf mmc2_conf;
+static struct omap_mmc_platform_data mmc2_data;
 
 static u64 mmc2_dmamask = 0xffffffff;
 
 static struct resource mmc2_resources[] = {
 	{
 		.start		= OMAP_MMC2_BASE,
-		.end		= OMAP_MMC2_BASE + 0x7f,
+		.end		= OMAP_MMC2_END,
 		.flags		= IORESOURCE_MEM,
 	},
 	{
-		.start		= INT_1610_MMC2,
+		.start		= OMAP_MMC2_INT,
 		.flags		= IORESOURCE_IRQ,
 	},
 };
@@ -255,26 +270,19 @@ static struct platform_device mmc_omap_device2 = {
 	.id		= 2,
 	.dev = {
 		.dma_mask	= &mmc2_dmamask,
-		.platform_data	= &mmc2_conf,
+		.platform_data	= &mmc2_data,
 	},
 	.num_resources	= ARRAY_SIZE(mmc2_resources),
 	.resource	= mmc2_resources,
 };
 #endif
 
-static void __init omap_init_mmc(void)
+static inline void omap_init_mmc_conf(const struct omap_mmc_config *mmc_conf)
 {
-	const struct omap_mmc_config	*mmc_conf;
-	const struct omap_mmc_conf	*mmc;
-
-	/* NOTE:  assumes MMC was never (wrongly) enabled */
-	mmc_conf = omap_get_config(OMAP_TAG_MMC, struct omap_mmc_config);
-	if (!mmc_conf)
+	if (cpu_is_omap2430() || cpu_is_omap34xx())
 		return;
 
-	/* block 1 is always available and has just one pinout option */
-	mmc = &mmc_conf->mmc[0];
-	if (mmc->enabled) {
+	if (mmc_conf->mmc[0].enabled) {
 		if (cpu_is_omap24xx()) {
 			omap_cfg_reg(H18_24XX_MMC_CMD);
 			omap_cfg_reg(H15_24XX_MMC_CLKI);
@@ -292,7 +300,7 @@ static void __init omap_init_mmc(void)
 				omap_cfg_reg(P20_1710_MMC_DATDIR0);
 			}
 		}
-		if (mmc->wire4) {
+		if (mmc_conf->mmc[0].wire4) {
 			if (cpu_is_omap24xx()) {
 				omap_cfg_reg(H14_24XX_MMC_DAT1);
 				omap_cfg_reg(E19_24XX_MMC_DAT2);
@@ -303,25 +311,35 @@ static void __init omap_init_mmc(void)
 			} else {
 				omap_cfg_reg(MMC_DAT1);
 				/* NOTE:  DAT2 can be on W10 (here) or M15 */
-				if (!mmc->nomux)
+				if (!mmc_conf->mmc[0].nomux)
 					omap_cfg_reg(MMC_DAT2);
 				omap_cfg_reg(MMC_DAT3);
 			}
 		}
-		mmc1_conf = *mmc;
-		(void) platform_device_register(&mmc_omap_device1);
+#if defined(CONFIG_ARCH_OMAP2420)
+		if (mmc_conf->mmc[0].internal_clock) {
+			/*
+			 * Use internal loop-back in MMC/SDIO
+			 * Module Input Clock selection
+			 */
+			if (cpu_is_omap24xx()) {
+				u32 v = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0);
+				v |= (1 << 24); /* not used in 243x */
+				omap_ctrl_writel(v, OMAP2_CONTROL_DEVCONF0);
+			}
+		}
+#endif
 	}
 
 #ifdef	CONFIG_ARCH_OMAP16XX
 	/* block 2 is on newer chips, and has many pinout options */
-	mmc = &mmc_conf->mmc[1];
-	if (mmc->enabled) {
-		if (!mmc->nomux) {
+	if (mmc_conf->mmc[1].enabled) {
+		if (!mmc_conf->mmc[1].nomux) {
 			omap_cfg_reg(Y8_1610_MMC2_CMD);
 			omap_cfg_reg(Y10_1610_MMC2_CLK);
 			omap_cfg_reg(R18_1610_MMC2_CLKIN);
 			omap_cfg_reg(W8_1610_MMC2_DAT0);
-			if (mmc->wire4) {
+			if (mmc_conf->mmc[1].wire4) {
 				omap_cfg_reg(V8_1610_MMC2_DAT1);
 				omap_cfg_reg(W15_1610_MMC2_DAT2);
 				omap_cfg_reg(R10_1610_MMC2_DAT3);
@@ -337,14 +355,55 @@ static void __init omap_init_mmc(void)
 		if (cpu_is_omap1710())
 			omap_writel(omap_readl(MOD_CONF_CTRL_1) | (1 << 24),
 				     MOD_CONF_CTRL_1);
-		mmc2_conf = *mmc;
+	}
+#endif
+}
+
+static void __init omap_init_mmc(void)
+{
+	const struct omap_mmc_config	*mmc_conf;
+
+	/* NOTE:  assumes MMC was never (wrongly) enabled */
+	mmc_conf = omap_get_config(OMAP_TAG_MMC, struct omap_mmc_config);
+	if (!mmc_conf)
+		return;
+
+	omap_init_mmc_conf(mmc_conf);
+
+	if (mmc_conf->mmc[0].enabled) {
+		mmc1_data.conf = mmc_conf->mmc[0];
+		(void) platform_device_register(&mmc_omap_device1);
+	}
+
+#if defined(CONFIG_ARCH_OMAP16XX) || defined(CONFIG_ARCH_OMAP2430) || \
+	defined(CONFIG_ARCH_OMAP34XX)
+	if (mmc_conf->mmc[1].enabled) {
+		mmc2_data.conf = mmc_conf->mmc[1];
 		(void) platform_device_register(&mmc_omap_device2);
 	}
 #endif
-	return;
 }
+
+void omap_set_mmc_info(int host, const struct omap_mmc_platform_data *info)
+{
+	switch (host) {
+	case 1:
+		mmc1_data = *info;
+		break;
+#if defined(CONFIG_ARCH_OMAP16XX) || defined(CONFIG_ARCH_OMAP2430) || \
+	defined(CONFIG_ARCH_OMAP34XX)
+	case 2:
+		mmc2_data = *info;
+		break;
+#endif
+	default:
+		BUG();
+	}
+}
+
 #else
 static inline void omap_init_mmc(void) {}
+void omap_set_mmc_info(int host, const struct omap_mmc_platform_data *info) {}
 #endif
 
 /*-------------------------------------------------------------------------*/
diff --git a/drivers/pcmcia/soc_common.c b/drivers/pcmcia/soc_common.c
index c48f3f69bdaf..da3972153226 100644
--- a/drivers/pcmcia/soc_common.c
+++ b/drivers/pcmcia/soc_common.c
@@ -748,7 +748,9 @@ int soc_common_drv_pcmcia_probe(struct device *dev, struct pcmcia_low_level *ops
 
 		add_timer(&skt->poll_timer);
 
-		device_create_file(&skt->socket.dev, &dev_attr_status);
+		ret = device_create_file(&skt->socket.dev, &dev_attr_status);
+		if (ret)
+			goto out_err_8;
 	}
 
 	dev_set_drvdata(dev, sinfo);
@@ -758,6 +760,8 @@ int soc_common_drv_pcmcia_probe(struct device *dev, struct pcmcia_low_level *ops
 	do {
 		skt = &sinfo->skt[i];
 
+		device_remove_file(&skt->socket.dev, &dev_attr_status);
+ out_err_8:
 		del_timer_sync(&skt->poll_timer);
 		pcmcia_unregister_socket(&skt->socket);
 
diff --git a/drivers/serial/imx.c b/drivers/serial/imx.c
index 6a29f9330a73..3f90f1bbbbcd 100644
--- a/drivers/serial/imx.c
+++ b/drivers/serial/imx.c
@@ -127,8 +127,13 @@
 #define  UCR3_RXDSEN	 (1<<6)  /* Receive status interrupt enable */
 #define  UCR3_AIRINTEN   (1<<5)  /* Async IR wake interrupt enable */
 #define  UCR3_AWAKEN	 (1<<4)  /* Async wake interrupt enable */
-#define  UCR3_REF25 	 (1<<3)  /* Ref freq 25 MHz */
-#define  UCR3_REF30 	 (1<<2)  /* Ref Freq 30 MHz */
+#ifdef CONFIG_ARCH_IMX
+#define  UCR3_REF25 	 (1<<3)  /* Ref freq 25 MHz, only on mx1 */
+#define  UCR3_REF30 	 (1<<2)  /* Ref Freq 30 MHz, only on mx1 */
+#endif
+#if defined CONFIG_ARCH_MX2 || defined CONFIG_ARCH_MX3
+#define  UCR3_RXDMUXSEL	 (1<<2)  /* RXD Muxed Input Select, on mx2/mx3 */
+#endif
 #define  UCR3_INVT  	 (1<<1)  /* Inverted Infrared transmission */
 #define  UCR3_BPEN  	 (1<<0)  /* Preset registers enable */
 #define  UCR4_CTSTL_32   (32<<10) /* CTS trigger level (32 chars) */
@@ -445,7 +450,7 @@ static irqreturn_t imx_int(int irq, void *dev_id)
 			readl(sport->port.membase + UCR1) & UCR1_TXMPTYEN)
 		imx_txint(irq, dev_id);
 
-	if (sts & USR1_RTSS)
+	if (sts & USR1_RTSD)
 		imx_rtsint(irq, dev_id);
 
 	return IRQ_HANDLED;
@@ -598,6 +603,12 @@ static int imx_startup(struct uart_port *port)
 	temp |= (UCR2_RXEN | UCR2_TXEN);
 	writel(temp, sport->port.membase + UCR2);
 
+#if defined CONFIG_ARCH_MX2 || defined CONFIG_ARCH_MX3
+	temp = readl(sport->port.membase + UCR3);
+	temp |= UCR3_RXDMUXSEL;
+	writel(temp, sport->port.membase + UCR3);
+#endif
+
 	/*
 	 * Enable modem status interrupts
 	 */
@@ -1133,13 +1144,19 @@ static int serial_imx_probe(struct platform_device *pdev)
 	if(pdata && (pdata->flags & IMXUART_HAVE_RTSCTS))
 		sport->have_rtscts = 1;
 
-	if (pdata->init)
-		pdata->init(pdev);
+	if (pdata->init) {
+		ret = pdata->init(pdev);
+		if (ret)
+			goto clkput;
+	}
 
 	uart_add_one_port(&imx_reg, &sport->port);
 	platform_set_drvdata(pdev, &sport->port);
 
 	return 0;
+clkput:
+	clk_put(sport->clk);
+	clk_disable(sport->clk);
 unmap:
 	iounmap(sport->port.membase);
 free: