blob: b461311a2ae71d7ddfd7695e6bb8801daa6354aa (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
|
#ifndef CYPRESS_M8_H
#define CYPRESS_M8_H
/*
* definitions and function prototypes used for the cypress USB to Serial
* controller
*/
/*
* For sending our feature buffer - controlling serial communication states.
* Linux HID has no support for serial devices so we do this through the driver
*/
#define HID_REQ_GET_REPORT 0x01
#define HID_REQ_SET_REPORT 0x09
/* List other cypress USB to Serial devices here, and add them to the id_table */
/* DeLorme Earthmate USB - a GPS device */
#define VENDOR_ID_DELORME 0x1163
#define PRODUCT_ID_EARTHMATEUSB 0x0100
#define PRODUCT_ID_EARTHMATEUSB_LT20 0x0200
/* Cypress HID->COM RS232 Adapter */
#define VENDOR_ID_CYPRESS 0x04b4
#define PRODUCT_ID_CYPHIDCOM 0x5500
/* FRWD Dongle - a GPS sports watch */
#define VENDOR_ID_FRWD 0x6737
#define PRODUCT_ID_CYPHIDCOM_FRWD 0x0001
/* Powercom UPS, chip CY7C63723 */
#define VENDOR_ID_POWERCOM 0x0d9f
#define PRODUCT_ID_UPS 0x0002
/* Nokia CA-42 USB to serial cable */
#define VENDOR_ID_DAZZLE 0x07d0
#define PRODUCT_ID_CA42 0x4101
/* End of device listing */
/* Used for setting / requesting serial line settings */
#define CYPRESS_SET_CONFIG 0x01
#define CYPRESS_GET_CONFIG 0x02
/* Used for throttle control */
#define THROTTLED 0x1
#define ACTUALLY_THROTTLED 0x2
/*
* chiptypes - used in case firmware differs from the generic form ... offering
* different baud speeds/etc.
*/
#define CT_EARTHMATE 0x01
#define CT_CYPHIDCOM 0x02
#define CT_CA42V2 0x03
#define CT_GENERIC 0x0F
/* End of chiptype definitions */
/* RS-232 serial data communication protocol definitions */
/* these are sent / read at byte 0 of the input/output hid reports */
/* You can find these values defined in the CY4601 USB to Serial design notes */
#define CONTROL_DTR 0x20 /* data terminal ready - flow control - host to device */
#define UART_DSR 0x20 /* data set ready - flow control - device to host */
#define CONTROL_RTS 0x10 /* request to send - flow control - host to device */
#define UART_CTS 0x10 /* clear to send - flow control - device to host */
#define UART_RI 0x10 /* ring indicator - modem - device to host */
#define UART_CD 0x40 /* carrier detect - modem - device to host */
#define CYP_ERROR 0x08 /* received from input report - device to host */
/* Note - the below has nothing to do with the "feature report" reset */
#define CONTROL_RESET 0x08 /* sent with output report - host to device */
/* End of RS-232 protocol definitions */
#endif /* CYPRESS_M8_H */
|
