path: root/drivers/net/phy/bcm7xxx.c

/*
 * Broadcom BCM7xxx internal transceivers support.
 *
 * Copyright (C) 2014, Broadcom Corporation
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * as published by the Free Software Foundation; either version
 * 2 of the License, or (at your option) any later version.
 */

#include <linux/module.h>
#include <linux/phy.h>
#include <linux/delay.h>
#include "bcm-phy-lib.h"
#include <linux/bitops.h>
#include <linux/brcmphy.h>
#include <linux/mdio.h>

/* Broadcom BCM7xxx internal PHY registers */

/* 40nm only register definitions */
#define MII_BCM7XXX_100TX_AUX_CTL	0x10
#define MII_BCM7XXX_100TX_FALSE_CAR	0x13
#define MII_BCM7XXX_100TX_DISC		0x14
#define MII_BCM7XXX_AUX_MODE		0x1d
#define  MII_BCM7XXX_64CLK_MDIO		BIT(12)
#define MII_BCM7XXX_TEST		0x1f
#define  MII_BCM7XXX_SHD_MODE_2		BIT(2)

/* 28nm only register definitions */
#define MISC_ADDR(base, channel)	base, channel

#define DSP_TAP10			MISC_ADDR(0x0a, 0)
#define PLL_PLLCTRL_1			MISC_ADDR(0x32, 1)
#define PLL_PLLCTRL_2			MISC_ADDR(0x32, 2)
#define PLL_PLLCTRL_4			MISC_ADDR(0x33, 0)

#define AFE_RXCONFIG_0			MISC_ADDR(0x38, 0)
#define AFE_RXCONFIG_1			MISC_ADDR(0x38, 1)
#define AFE_RXCONFIG_2			MISC_ADDR(0x38, 2)
#define AFE_RX_LP_COUNTER		MISC_ADDR(0x38, 3)
#define AFE_TX_CONFIG			MISC_ADDR(0x39, 0)
#define AFE_VDCA_ICTRL_0		MISC_ADDR(0x39, 1)
#define AFE_VDAC_OTHERS_0		MISC_ADDR(0x39, 3)
#define AFE_HPF_TRIM_OTHERS		MISC_ADDR(0x3a, 0)

static void r_rc_cal_reset(struct phy_device *phydev)
{
	/* Reset R_CAL/RC_CAL Engine */
	bcm_phy_write_exp(phydev, 0x00b0, 0x0010);

	/* Disable Reset R_AL/RC_CAL Engine */
	bcm_phy_write_exp(phydev, 0x00b0, 0x0000);
}

static int bcm7xxx_28nm_b0_afe_config_init(struct phy_device *phydev)
{
	/* Increase VCO range to prevent unlocking problem of PLL at low
	 * temp
	 */
	bcm_phy_write_misc(phydev, PLL_PLLCTRL_1, 0x0048);

	/* Change Ki to 011 */
	bcm_phy_write_misc(phydev, PLL_PLLCTRL_2, 0x021b);

	/* Disable loading of TVCO buffer to bandgap, set bandgap trim
	 * to 111
	 */
	bcm_phy_write_misc(phydev, PLL_PLLCTRL_4, 0x0e20);

	/* Adjust bias current trim by -3 */
	bcm_phy_write_misc(phydev, DSP_TAP10, 0x690b);

	/* Switch to CORE_BASE1E */
	phy_write(phydev, MII_BRCM_CORE_BASE1E, 0xd);

	r_rc_cal_reset(phydev);

	/* write AFE_RXCONFIG_0 */
	bcm_phy_write_misc(phydev, AFE_RXCONFIG_0, 0xeb19);

	/* write AFE_RXCONFIG_1 */
	bcm_phy_write_misc(phydev, AFE_RXCONFIG_1, 0x9a3f);

	/* write AFE_RX_LP_COUNTER */
	bcm_phy_write_misc(phydev, AFE_RX_LP_COUNTER, 0x7fc0);

	/* write AFE_HPF_TRIM_OTHERS */
	bcm_phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x000b);

	/* write AFTE_TX_CONFIG */
	bcm_phy_write_misc(phydev, AFE_TX_CONFIG, 0x0800);

	return 0;
}

static int bcm7xxx_28nm_d0_afe_config_init(struct phy_device *phydev)
{
	/* AFE_RXCONFIG_0 */
	bcm_phy_write_misc(phydev, AFE_RXCONFIG_0, 0xeb15);

	/* AFE_RXCONFIG_1 */
	bcm_phy_write_misc(phydev, AFE_RXCONFIG_1, 0x9b2f);

	/* AFE_RXCONFIG_2, set rCal offset for HT=0 code and LT=-2 code */
	bcm_phy_write_misc(phydev, AFE_RXCONFIG_2, 0x2003);

	/* AFE_RX_LP_COUNTER, set RX bandwidth to maximum */
	bcm_phy_write_misc(phydev, AFE_RX_LP_COUNTER, 0x7fc0);

	/* AFE_TX_CONFIG, set 100BT Cfeed=011 to improve rise/fall time */
	bcm_phy_write_misc(phydev, AFE_TX_CONFIG, 0x431);

	/* AFE_VDCA_ICTRL_0, set Iq=1101 instead of 0111 for AB symmetry */
	bcm_phy_write_misc(phydev, AFE_VDCA_ICTRL_0, 0xa7da);

	/* AFE_VDAC_OTHERS_0, set 1000BT Cidac=010 for all ports */
	bcm_phy_write_misc(phydev, AFE_VDAC_OTHERS_0, 0xa020);

	/* AFE_HPF_TRIM_OTHERS, set 100Tx/10BT to -4.5% swing and set rCal
	 * offset for HT=0 code
	 */
	bcm_phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x00e3);

	/* CORE_BASE1E, force trim to overwrite and set I_ext trim to 0000 */
	phy_write(phydev, MII_BRCM_CORE_BASE1E, 0x0010);

	/* DSP_TAP10, adjust bias current trim (+0% swing, +0 tick) */
	bcm_phy_write_misc(phydev, DSP_TAP10, 0x011b);

	/* Reset R_CAL/RC_CAL engine */
	r_rc_cal_reset(phydev);

	return 0;
}

static int bcm7xxx_28nm_e0_plus_afe_config_init(struct phy_device *phydev)
{
	/* AFE_RXCONFIG_1, provide more margin for INL/DNL measurement */
	bcm_phy_write_misc(phydev, AFE_RXCONFIG_1, 0x9b2f);

	/* AFE_TX_CONFIG, set 100BT Cfeed=011 to improve rise/fall time */
	bcm_phy_write_misc(phydev, AFE_TX_CONFIG, 0x431);

	/* AFE_VDCA_ICTRL_0, set Iq=1101 instead of 0111 for AB symmetry */
	bcm_phy_write_misc(phydev, AFE_VDCA_ICTRL_0, 0xa7da);

	/* AFE_HPF_TRIM_OTHERS, set 100Tx/10BT to -4.5% swing and set rCal
	 * offset for HT=0 code
	 */
	bcm_phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x00e3);

	/* CORE_BASE1E, force trim to overwrite and set I_ext trim to 0000 */
	phy_write(phydev, MII_BRCM_CORE_BASE1E, 0x0010);

	/* DSP_TAP10, adjust bias current trim (+0% swing, +0 tick) */
	bcm_phy_write_misc(phydev, DSP_TAP10, 0x011b);

	/* Reset R_CAL/RC_CAL engine */
	r_rc_cal_reset(phydev);

	return 0;
}

static int bcm7xxx_28nm_config_init(struct phy_device *phydev)
{
	u8 rev = PHY_BRCM_7XXX_REV(phydev->dev_flags);
	u8 patch = PHY_BRCM_7XXX_PATCH(phydev->dev_flags);
	int ret = 0;

	pr_info_once("%s: %s PHY revision: 0x%02x, patch: %d\n",
		     phydev_name(phydev), phydev->drv->name, rev, patch);

	/* Dummy read to a register to workaround an issue upon reset where the
	 * internal inverter may not allow the first MDIO transaction to pass
	 * the MDIO management controller and make us return 0xffff for such
	 * reads.
	 */
	phy_read(phydev, MII_BMSR);

	switch (rev) {
	case 0xb0:
		ret = bcm7xxx_28nm_b0_afe_config_init(phydev);
		break;
	case 0xd0:
		ret = bcm7xxx_28nm_d0_afe_config_init(phydev);
		break;
	case 0xe0:
	case 0xf0:
	/* Rev G0 introduces a roll over */
	case 0x10:
		ret = bcm7xxx_28nm_e0_plus_afe_config_init(phydev);
		break;
	default:
		break;
	}

	if (ret)
		return ret;

	ret = bcm_phy_enable_eee(phydev);
	if (ret)
		return ret;

	return bcm_phy_enable_apd(phydev, true);
}

static int bcm7xxx_28nm_resume(struct phy_device *phydev)
{
	int ret;

	/* Re-apply workarounds coming out suspend/resume */
	ret = bcm7xxx_28nm_config_init(phydev);
	if (ret)
		return ret;

	/* 28nm Gigabit PHYs come out of reset without any half-duplex
	 * or "hub" compliant advertised mode, fix that. This does not
	 * cause any problems with the PHY library since genphy_config_aneg()
	 * gracefully handles auto-negotiated and forced modes.
	 */
	return genphy_config_aneg(phydev);
}

static int phy_set_clr_bits(struct phy_device *dev, int location,
					int set_mask, int clr_mask)
{
	int v, ret;

	v = phy_read(dev, location);
	if (v < 0)
		return v;

	v &= ~clr_mask;
	v |= set_mask;

	ret = phy_write(dev, location, v);
	if (ret < 0)
		return ret;

	return v;
}

static int bcm7xxx_config_init(struct phy_device *phydev)
{
	int ret;

	/* Enable 64 clock MDIO */
	phy_write(phydev, MII_BCM7XXX_AUX_MODE, MII_BCM7XXX_64CLK_MDIO);
	phy_read(phydev, MII_BCM7XXX_AUX_MODE);

	/* set shadow mode 2 */
	ret = phy_set_clr_bits(phydev, MII_BCM7XXX_TEST,
			MII_BCM7XXX_SHD_MODE_2, MII_BCM7XXX_SHD_MODE_2);
	if (ret < 0)
		return ret;

	/* set iddq_clkbias */
	phy_write(phydev, MII_BCM7XXX_100TX_DISC, 0x0F00);
	udelay(10);

	/* reset iddq_clkbias */
	phy_write(phydev, MII_BCM7XXX_100TX_DISC, 0x0C00);

	phy_write(phydev, MII_BCM7XXX_100TX_FALSE_CAR, 0x7555);

	/* reset shadow mode 2 */
	ret = phy_set_clr_bits(phydev, MII_BCM7XXX_TEST, 0, MII_BCM7XXX_SHD_MODE_2);
	if (ret < 0)
		return ret;

	return 0;
}

/* Workaround for putting the PHY in IDDQ mode, required
 * for all BCM7XXX 40nm and 65nm PHYs
 */
static int bcm7xxx_suspend(struct phy_device *phydev)
{
	int ret;
	const struct bcm7xxx_regs {
		int reg;
		u16 value;
	} bcm7xxx_suspend_cfg[] = {
		{ MII_BCM7XXX_TEST, 0x008b },
		{ MII_BCM7XXX_100TX_AUX_CTL, 0x01c0 },
		{ MII_BCM7XXX_100TX_DISC, 0x7000 },
		{ MII_BCM7XXX_TEST, 0x000f },
		{ MII_BCM7XXX_100TX_AUX_CTL, 0x20d0 },
		{ MII_BCM7XXX_TEST, 0x000b },
	};
	unsigned int i;

	for (i = 0; i < ARRAY_SIZE(bcm7xxx_suspend_cfg); i++) {
		ret = phy_write(phydev,
				bcm7xxx_suspend_cfg[i].reg,
				bcm7xxx_suspend_cfg[i].value);
		if (ret)
			return ret;
	}

	return 0;
}

#define BCM7XXX_28NM_GPHY(_oui, _name)					\
{									\
	.phy_id		= (_oui),					\
	.phy_id_mask	= 0xfffffff0,					\
	.name		= _name,					\
	.features	= PHY_GBIT_FEATURES |				\
			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,	\
	.flags		= PHY_IS_INTERNAL,				\
	.config_init	= bcm7xxx_28nm_config_init,			\
	.config_aneg	= genphy_config_aneg,				\
	.read_status	= genphy_read_status,				\
	.resume		= bcm7xxx_28nm_resume,				\
}

#define BCM7XXX_40NM_EPHY(_oui, _name)					\
{									\
	.phy_id         = (_oui),					\
	.phy_id_mask    = 0xfffffff0,					\
	.name           = _name,					\
	.features       = PHY_BASIC_FEATURES |				\
			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,	\
	.flags          = PHY_IS_INTERNAL,				\
	.config_init    = bcm7xxx_config_init,				\
	.config_aneg    = genphy_config_aneg,				\
	.read_status    = genphy_read_status,				\
	.suspend        = bcm7xxx_suspend,				\
	.resume         = bcm7xxx_config_init,				\
}

static struct phy_driver bcm7xxx_driver[] = {
	BCM7XXX_28NM_GPHY(PHY_ID_BCM7250, "Broadcom BCM7250"),
	BCM7XXX_28NM_GPHY(PHY_ID_BCM7364, "Broadcom BCM7364"),
	BCM7XXX_28NM_GPHY(PHY_ID_BCM7366, "Broadcom BCM7366"),
	BCM7XXX_28NM_GPHY(PHY_ID_BCM7439, "Broadcom BCM7439"),
	BCM7XXX_28NM_GPHY(PHY_ID_BCM7439_2, "Broadcom BCM7439 (2)"),
	BCM7XXX_28NM_GPHY(PHY_ID_BCM7445, "Broadcom BCM7445"),
	BCM7XXX_40NM_EPHY(PHY_ID_BCM7346, "Broadcom BCM7346"),
	BCM7XXX_40NM_EPHY(PHY_ID_BCM7362, "Broadcom BCM7362"),
	BCM7XXX_40NM_EPHY(PHY_ID_BCM7425, "Broadcom BCM7425"),
	BCM7XXX_40NM_EPHY(PHY_ID_BCM7429, "Broadcom BCM7429"),
	BCM7XXX_40NM_EPHY(PHY_ID_BCM7435, "Broadcom BCM7435"),
};

static struct mdio_device_id __maybe_unused bcm7xxx_tbl[] = {
	{ PHY_ID_BCM7250, 0xfffffff0, },
	{ PHY_ID_BCM7364, 0xfffffff0, },
	{ PHY_ID_BCM7366, 0xfffffff0, },
	{ PHY_ID_BCM7346, 0xfffffff0, },
	{ PHY_ID_BCM7362, 0xfffffff0, },
	{ PHY_ID_BCM7425, 0xfffffff0, },
	{ PHY_ID_BCM7429, 0xfffffff0, },
	{ PHY_ID_BCM7439, 0xfffffff0, },
	{ PHY_ID_BCM7435, 0xfffffff0, },
	{ PHY_ID_BCM7445, 0xfffffff0, },
	{ }
};

module_phy_driver(bcm7xxx_driver);

MODULE_DEVICE_TABLE(mdio, bcm7xxx_tbl);

MODULE_DESCRIPTION("Broadcom BCM7xxx internal PHY driver");
MODULE_LICENSE("GPL");
MODULE_AUTHOR("Broadcom Corporation");