1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
|
/dts-v1/;
#include "jz4780.dtsi"
#include <dt-bindings/gpio/gpio.h>
/ {
compatible = "img,ci20", "ingenic,jz4780";
aliases {
serial0 = &uart0;
serial1 = &uart1;
serial3 = &uart3;
serial4 = &uart4;
};
chosen {
stdout-path = &uart4;
};
memory {
device_type = "memory";
reg = <0x0 0x10000000
0x30000000 0x30000000>;
};
eth0_power: fixedregulator@0 {
compatible = "regulator-fixed";
regulator-name = "eth0_power";
gpio = <&gpb 25 GPIO_ACTIVE_LOW>;
enable-active-high;
};
};
&ext {
clock-frequency = <48000000>;
};
&uart0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pins_uart0>;
};
&uart1 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pins_uart1>;
};
&uart3 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pins_uart2>;
};
&uart4 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pins_uart4>;
};
&nemc {
status = "okay";
nandc: nand-controller@1 {
compatible = "ingenic,jz4780-nand";
reg = <1 0 0x1000000>;
#address-cells = <1>;
#size-cells = <0>;
ingenic,bch-controller = <&bch>;
ingenic,nemc-tAS = <10>;
ingenic,nemc-tAH = <5>;
ingenic,nemc-tBP = <10>;
ingenic,nemc-tAW = <15>;
ingenic,nemc-tSTRV = <100>;
/*
* Only CLE/ALE are needed for the devices that are connected, rather
* than the full address line set.
*/
pinctrl-names = "default";
pinctrl-0 = <&pins_nemc>;
nand@1 {
reg = <1>;
nand-ecc-step-size = <1024>;
nand-ecc-strength = <24>;
nand-ecc-mode = "hw";
nand-on-flash-bbt;
pinctrl-names = "default";
pinctrl-0 = <&pins_nemc_cs1>;
partitions {
compatible = "fixed-partitions";
#address-cells = <2>;
#size-cells = <2>;
partition@0 {
label = "u-boot-spl";
reg = <0x0 0x0 0x0 0x800000>;
};
partition@0x800000 {
label = "u-boot";
reg = <0x0 0x800000 0x0 0x200000>;
};
partition@0xa00000 {
label = "u-boot-env";
reg = <0x0 0xa00000 0x0 0x200000>;
};
partition@0xc00000 {
label = "boot";
reg = <0x0 0xc00000 0x0 0x4000000>;
};
partition@0x8c00000 {
label = "system";
reg = <0x0 0x4c00000 0x1 0xfb400000>;
};
};
};
};
dm9000@6 {
compatible = "davicom,dm9000";
davicom,no-eeprom;
pinctrl-names = "default";
pinctrl-0 = <&pins_nemc_cs6>;
reg = <6 0 1 /* addr */
6 2 1>; /* data */
ingenic,nemc-tAS = <15>;
ingenic,nemc-tAH = <10>;
ingenic,nemc-tBP = <20>;
ingenic,nemc-tAW = <50>;
ingenic,nemc-tSTRV = <100>;
reset-gpios = <&gpf 12 GPIO_ACTIVE_HIGH>;
vcc-supply = <ð0_power>;
interrupt-parent = <&gpe>;
interrupts = <19 4>;
};
};
&bch {
status = "okay";
};
&pinctrl {
pins_uart0: uart0 {
function = "uart0";
groups = "uart0-data";
bias-disable;
};
pins_uart1: uart1 {
function = "uart1";
groups = "uart1-data";
bias-disable;
};
pins_uart2: uart2 {
function = "uart2";
groups = "uart2-data", "uart2-hwflow";
bias-disable;
};
pins_uart4: uart4 {
function = "uart4";
groups = "uart4-data";
bias-disable;
};
pins_nemc: nemc {
function = "nemc";
groups = "nemc-data", "nemc-cle-ale", "nemc-rd-we", "nemc-frd-fwe";
bias-disable;
};
pins_nemc_cs1: nemc-cs1 {
function = "nemc-cs1";
groups = "nemc-cs1";
bias-disable;
};
pins_nemc_cs6: nemc-cs6 {
function = "nemc-cs6";
groups = "nemc-cs6";
bias-disable;
};
};
|
