1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
|
/*
* arch/arm/mach-spear13xx/platsmp.c
*
* based upon linux/arch/arm/mach-realview/platsmp.c
*
* Copyright (C) 2012 ST Microelectronics Ltd.
* Shiraz Hashim <shiraz.hashim@st.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/delay.h>
#include <linux/jiffies.h>
#include <linux/io.h>
#include <linux/smp.h>
#include <asm/cacheflush.h>
#include <asm/hardware/gic.h>
#include <asm/smp_scu.h>
#include <mach/spear.h>
#include <mach/generic.h>
static DEFINE_SPINLOCK(boot_lock);
static void __iomem *scu_base = IOMEM(VA_SCU_BASE);
static void __cpuinit spear13xx_secondary_init(unsigned int cpu)
{
/*
* if any interrupts are already enabled for the primary
* core (e.g. timer irq), then they will not have been enabled
* for us: do so
*/
gic_secondary_init(0);
/*
* let the primary processor know we're out of the
* pen, then head off into the C entry point
*/
pen_release = -1;
smp_wmb();
/*
* Synchronise with the boot thread.
*/
spin_lock(&boot_lock);
spin_unlock(&boot_lock);
}
static int __cpuinit spear13xx_boot_secondary(unsigned int cpu, struct task_struct *idle)
{
unsigned long timeout;
/*
* set synchronisation state between this boot processor
* and the secondary one
*/
spin_lock(&boot_lock);
/*
* The secondary processor is waiting to be released from
* the holding pen - release it, then wait for it to flag
* that it has been released by resetting pen_release.
*
* Note that "pen_release" is the hardware CPU ID, whereas
* "cpu" is Linux's internal ID.
*/
pen_release = cpu;
flush_cache_all();
outer_flush_all();
timeout = jiffies + (1 * HZ);
while (time_before(jiffies, timeout)) {
smp_rmb();
if (pen_release == -1)
break;
udelay(10);
}
/*
* now the secondary core is starting up let it run its
* calibrations, then wait for it to finish
*/
spin_unlock(&boot_lock);
return pen_release != -1 ? -ENOSYS : 0;
}
/*
* Initialise the CPU possible map early - this describes the CPUs
* which may be present or become present in the system.
*/
static void __init spear13xx_smp_init_cpus(void)
{
unsigned int i, ncores = scu_get_core_count(scu_base);
if (ncores > nr_cpu_ids) {
pr_warn("SMP: %u cores greater than maximum (%u), clipping\n",
ncores, nr_cpu_ids);
ncores = nr_cpu_ids;
}
for (i = 0; i < ncores; i++)
set_cpu_possible(i, true);
set_smp_cross_call(gic_raise_softirq);
}
static void __init spear13xx_smp_prepare_cpus(unsigned int max_cpus)
{
scu_enable(scu_base);
/*
* Write the address of secondary startup into the system-wide location
* (presently it is in SRAM). The BootMonitor waits until it receives a
* soft interrupt, and then the secondary CPU branches to this address.
*/
__raw_writel(virt_to_phys(spear13xx_secondary_startup), SYS_LOCATION);
}
struct smp_operations spear13xx_smp_ops __initdata = {
.smp_init_cpus = spear13xx_smp_init_cpus,
.smp_prepare_cpus = spear13xx_smp_prepare_cpus,
.smp_secondary_init = spear13xx_secondary_init,
.smp_boot_secondary = spear13xx_boot_secondary,
#ifdef CONFIG_HOTPLUG_CPU
.cpu_die = spear13xx_cpu_die,
#endif
};
|
