summaryrefslogtreecommitdiffstats
path: root/arch/arm/mach-davinci/serial.c
blob: f2625814c3c9b3160d5b163efbbd9cb799ced23e (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
/*
 * TI DaVinci serial driver
 *
 * Copyright (C) 2006 Texas Instruments.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
 * GNU General Public License for more details.
 *
 *  You should have received a copy of the GNU General Public License
 *  along with this program; if not, write to the Free Software
 *  Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
 *
 */

#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/serial_8250.h>
#include <linux/serial_reg.h>
#include <linux/platform_device.h>
#include <linux/delay.h>
#include <linux/clk.h>
#include <linux/io.h>

#include <mach/serial.h>
#include <mach/cputype.h>

static inline unsigned int serial_read_reg(struct plat_serial8250_port *up,
					   int offset)
{
	offset <<= up->regshift;

	WARN_ONCE(!up->membase, "unmapped read: uart[%d]\n", offset);

	return (unsigned int)__raw_readl(up->membase + offset);
}

static inline void serial_write_reg(struct plat_serial8250_port *p, int offset,
				    int value)
{
	offset <<= p->regshift;

	WARN_ONCE(!p->membase, "unmapped write: uart[%d]\n", offset);

	__raw_writel(value, p->membase + offset);
}

static void __init davinci_serial_reset(struct plat_serial8250_port *p)
{
	unsigned int pwremu = 0;

	serial_write_reg(p, UART_IER, 0);  /* disable all interrupts */

	/* reset both transmitter and receiver: bits 14,13 = UTRST, URRST */
	serial_write_reg(p, UART_DAVINCI_PWREMU, pwremu);
	mdelay(10);

	pwremu |= (0x3 << 13);
	pwremu |= 0x1;
	serial_write_reg(p, UART_DAVINCI_PWREMU, pwremu);

	if (cpu_is_davinci_dm646x())
		serial_write_reg(p, UART_DM646X_SCR,
				 UART_DM646X_SCR_TX_WATERMARK);
}

/* Enable UART clock and obtain its rate */
int __init davinci_serial_setup_clk(unsigned instance, unsigned int *rate)
{
	char name[16];
	struct clk *clk;
	struct davinci_soc_info *soc_info = &davinci_soc_info;
	struct device *dev = &soc_info->serial_dev->dev;

	sprintf(name, "uart%d", instance);
	clk = clk_get(dev, name);
	if (IS_ERR(clk)) {
		pr_err("%s:%d: failed to get UART%d clock\n",
					__func__, __LINE__, instance);
		return PTR_ERR(clk);
	}

	clk_prepare_enable(clk);

	if (rate)
		*rate = clk_get_rate(clk);

	return 0;
}

int __init davinci_serial_init(struct davinci_uart_config *info)
{
	int i, ret;
	struct davinci_soc_info *soc_info = &davinci_soc_info;
	struct device *dev = &soc_info->serial_dev->dev;
	struct plat_serial8250_port *p = dev->platform_data;

	/*
	 * Make sure the serial ports are muxed on at this point.
	 * You have to mux them off in device drivers later on if not needed.
	 */
	for (i = 0; p->flags; i++, p++) {
		if (!(info->enabled_uarts & (1 << i)))
			continue;

		ret = davinci_serial_setup_clk(i, &p->uartclk);
		if (ret)
			continue;

		if (!p->membase && p->mapbase) {
			p->membase = ioremap(p->mapbase, SZ_4K);

			if (p->membase)
				p->flags &= ~UPF_IOREMAP;
			else
				pr_err("uart regs ioremap failed\n");
		}

		if (p->membase && p->type != PORT_AR7)
			davinci_serial_reset(p);
	}

	return platform_device_register(soc_info->serial_dev);
}