summaryrefslogtreecommitdiffstats
path: root/Documentation/networking/stmmac.txt
blob: cdd916da838d44317974161311d1f81e2db2c233 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
       STMicroelectronics 10/100/1000 Synopsys Ethernet driver

Copyright (C) 2007-2013  STMicroelectronics Ltd
Author: Giuseppe Cavallaro <peppe.cavallaro@st.com>

This is the driver for the MAC 10/100/1000 on-chip Ethernet controllers
(Synopsys IP blocks).

Currently this network device driver is for all STM embedded MAC/GMAC
(i.e. 7xxx/5xxx SoCs), SPEAr (arm), Loongson1B (mips) and XLINX XC2V3000
FF1152AMT0221 D1215994A VIRTEX FPGA board.

DWC Ether MAC 10/100/1000 Universal version 3.70a (and older) and DWC Ether
MAC 10/100 Universal version 4.0 have been used for developing this driver.

This driver supports both the platform bus and PCI.

Please, for more information also visit: www.stlinux.com

1) Kernel Configuration
The kernel configuration option is STMMAC_ETH:
 Device Drivers ---> Network device support ---> Ethernet (1000 Mbit) --->
 STMicroelectronics 10/100/1000 Ethernet driver (STMMAC_ETH)

2) Driver parameters list:
	debug: message level (0: no output, 16: all);
	phyaddr: to manually provide the physical address to the PHY device;
	dma_rxsize: DMA rx ring size;
	dma_txsize: DMA tx ring size;
	buf_sz: DMA buffer size;
	tc: control the HW FIFO threshold;
	watchdog: transmit timeout (in milliseconds);
	flow_ctrl: Flow control ability [on/off];
	pause: Flow Control Pause Time;
	eee_timer: tx EEE timer;
	chain_mode: select chain mode instead of ring.

3) Command line options
Driver parameters can be also passed in command line by using:
	stmmaceth=dma_rxsize:128,dma_txsize:512

4) Driver information and notes

4.1) Transmit process
The xmit method is invoked when the kernel needs to transmit a packet; it sets
the descriptors in the ring and informs the DMA engine that there is a packet
ready to be transmitted.
Once the controller has finished transmitting the packet, an interrupt is
triggered; So the driver will be able to release the socket buffers.
By default, the driver sets the NETIF_F_SG bit in the features field of the
net_device structure enabling the scatter/gather feature.

4.2) Receive process
When one or more packets are received, an interrupt happens. The interrupts
are not queued so the driver has to scan all the descriptors in the ring during
the receive process.
This is based on NAPI so the interrupt handler signals only if there is work
to be done, and it exits.
Then the poll method will be scheduled at some future point.
The incoming packets are stored, by the DMA, in a list of pre-allocated socket
buffers in order to avoid the memcpy (Zero-copy).

4.3) Interrupt Mitigation
The driver is able to mitigate the number of its DMA interrupts
using NAPI for the reception on chips older than the 3.50.
New chips have an HW RX-Watchdog used for this mitigation.

On Tx-side, the mitigation schema is based on a SW timer that calls the
tx function (stmmac_tx) to reclaim the resource after transmitting the
frames.
Also there is another parameter (like a threshold) used to program
the descriptors avoiding to set the interrupt on completion bit in
when the frame is sent (xmit).

Mitigation parameters can be tuned by ethtool.

4.4) WOL
Wake up on Lan feature through Magic and Unicast frames are supported for the
GMAC core.

4.5) DMA descriptors
Driver handles both normal and enhanced descriptors. The latter has been only
tested on DWC Ether MAC 10/100/1000 Universal version 3.41a and later.

STMMAC supports DMA descriptor to operate both in dual buffer (RING)
and linked-list(CHAINED) mode. In RING each descriptor points to two
data buffer pointers whereas in CHAINED mode they point to only one data
buffer pointer. RING mode is the default.

In CHAINED mode each descriptor will have pointer to next descriptor in
the list, hence creating the explicit chaining in the descriptor itself,
whereas such explicit chaining is not possible in RING mode.

4.6) Ethtool support
Ethtool is supported. Driver statistics and internal errors can be taken using:
ethtool -S ethX command. It is possible to dump registers etc.

4.7) Jumbo and Segmentation Offloading
Jumbo frames are supported and tested for the GMAC.
The GSO has been also added but it's performed in software.
LRO is not supported.

4.8) Physical
The driver is compatible with PAL to work with PHY and GPHY devices.

4.9) Platform information
Several driver's information can be passed through the platform
These are included in the include/linux/stmmac.h header file
and detailed below as well:

struct plat_stmmacenet_data {
	char *phy_bus_name;
	int bus_id;
	int phy_addr;
	int interface;
	struct stmmac_mdio_bus_data *mdio_bus_data;
	struct stmmac_dma_cfg *dma_cfg;
	int clk_csr;
	int has_gmac;
	int enh_desc;
	int tx_coe;
	int rx_coe;
	int bugged_jumbo;
	int pmt;
	int force_sf_dma_mode;
	int force_thresh_dma_mode;
	int riwt_off;
	void (*fix_mac_speed)(void *priv, unsigned int speed);
	void (*bus_setup)(void __iomem *ioaddr);
	int (*init)(struct platform_device *pdev);
	void (*exit)(struct platform_device *pdev);
	void *custom_cfg;
	void *custom_data;
	void *bsp_priv;
 };

Where:
 o phy_bus_name: phy bus name to attach to the stmmac.
 o bus_id: bus identifier.
 o phy_addr: the physical address can be passed from the platform.
	    If it is set to -1 the driver will automatically
	    detect it at run-time by probing all the 32 addresses.
 o interface: PHY device's interface.
 o mdio_bus_data: specific platform fields for the MDIO bus.
 o dma_cfg: internal DMA parameters
   o pbl: the Programmable Burst Length is maximum number of beats to
       be transferred in one DMA transaction.
       GMAC also enables the 4xPBL by default.
   o fixed_burst/mixed_burst/burst_len
 o clk_csr: fixed CSR Clock range selection.
 o has_gmac: uses the GMAC core.
 o enh_desc: if sets the MAC will use the enhanced descriptor structure.
 o tx_coe: core is able to perform the tx csum in HW.
 o rx_coe: the supports three check sum offloading engine types:
	   type_1, type_2 (full csum) and no RX coe.
 o bugged_jumbo: some HWs are not able to perform the csum in HW for
		over-sized frames due to limited buffer sizes.
		Setting this flag the csum will be done in SW on
		JUMBO frames.
 o pmt: core has the embedded power module (optional).
 o force_sf_dma_mode: force DMA to use the Store and Forward mode
		     instead of the Threshold.
 o force_thresh_dma_mode: force DMA to use the Threshold mode other than
		     the Store and Forward mode.
 o riwt_off: force to disable the RX watchdog feature and switch to NAPI mode.
 o fix_mac_speed: this callback is used for modifying some syscfg registers
		 (on ST SoCs) according to the link speed negotiated by the
		 physical layer .
 o bus_setup: perform HW setup of the bus. For example, on some ST platforms
	     this field is used to configure the AMBA  bridge to generate more
	     efficient STBus traffic.
 o init/exit: callbacks used for calling a custom initialization;
	     this is sometime necessary on some platforms (e.g. ST boxes)
	     where the HW needs to have set some PIO lines or system cfg
	     registers.
 o custom_cfg/custom_data: this is a custom configuration that can be passed
			   while initializing the resources.
 o bsp_priv: another private pointer.

For MDIO bus The we have:

 struct stmmac_mdio_bus_data {
	int (*phy_reset)(void *priv);
	unsigned int phy_mask;
	int *irqs;
	int probed_phy_irq;
 };

Where:
 o phy_reset: hook to reset the phy device attached to the bus.
 o phy_mask: phy mask passed when register the MDIO bus within the driver.
 o irqs: list of IRQs, one per PHY.
 o probed_phy_irq: if irqs is NULL, use this for probed PHY.

For DMA engine we have the following internal fields that should be
tuned according to the HW capabilities.

struct stmmac_dma_cfg {
	int pbl;
	int fixed_burst;
	int burst_len_supported;
};

Where:
 o pbl: Programmable Burst Length
 o fixed_burst: program the DMA to use the fixed burst mode
 o burst_len: this is the value we put in the register
	      supported values are provided as macros in
	      linux/stmmac.h header file.

---

Below an example how the structures above are using on ST platforms.

 static struct plat_stmmacenet_data stxYYY_ethernet_platform_data = {
	.has_gmac = 0,
	.enh_desc = 0,
	.fix_mac_speed = stxYYY_ethernet_fix_mac_speed,
				|
				|-> to write an internal syscfg
				|   on this platform when the
				|   link speed changes from 10 to
				|   100 and viceversa
	.init = &stmmac_claim_resource,
				|
				|-> On ST SoC this calls own "PAD"
				|   manager framework to claim
				|   all the resources necessary
				|   (GPIO ...). The .custom_cfg field
				|   is used to pass a custom config.
};

Below the usage of the stmmac_mdio_bus_data: on this SoC, in fact,
there are two MAC cores: one MAC is for MDIO Bus/PHY emulation
with fixed_link support.

static struct stmmac_mdio_bus_data stmmac1_mdio_bus = {
	.phy_reset = phy_reset;
		|
		|-> function to provide the phy_reset on this board
	.phy_mask = 0,
};

static struct fixed_phy_status stmmac0_fixed_phy_status = {
	.link = 1,
	.speed = 100,
	.duplex = 1,
};

During the board's device_init we can configure the first
MAC for fixed_link by calling:
  fixed_phy_add(PHY_POLL, 1, &stmmac0_fixed_phy_status));)
and the second one, with a real PHY device attached to the bus,
by using the stmmac_mdio_bus_data structure (to provide the id, the
reset procedure etc).

4.10) List of source files:
 o Kconfig
 o Makefile
 o stmmac_main.c: main network device driver;
 o stmmac_mdio.c: mdio functions;
 o stmmac_pci: PCI driver;
 o stmmac_platform.c: platform driver
 o stmmac_ethtool.c: ethtool support;
 o stmmac_timer.[ch]: timer code used for mitigating the driver dma interrupts
		      (only tested on ST40 platforms based);
 o stmmac.h: private driver structure;
 o common.h: common definitions and VFTs;
 o descs.h: descriptor structure definitions;
 o dwmac1000_core.c: GMAC core functions;
 o dwmac1000_dma.c:  dma functions for the GMAC chip;
 o dwmac1000.h: specific header file for the GMAC;
 o dwmac100_core: MAC 100 core and dma code;
 o dwmac100_dma.c: dma functions for the MAC chip;
 o dwmac1000.h: specific header file for the MAC;
 o dwmac_lib.c: generic DMA functions shared among chips;
 o enh_desc.c: functions for handling enhanced descriptors;
 o norm_desc.c: functions for handling normal descriptors;
 o chain_mode.c/ring_mode.c:: functions to manage RING/CHAINED modes;
 o mmc_core.c/mmc.h: Management MAC Counters;
 o stmmac_hwtstamp.c: HW timestamp support for PTP
 o stmmac_ptp.c: PTP 1588 clock

5) Debug Information

The driver exports many information i.e. internal statistics,
debug information, MAC and DMA registers etc.

These can be read in several ways depending on the
type of the information actually needed.

For example a user can be use the ethtool support
to get statistics: e.g. using: ethtool -S ethX
(that shows the Management counters (MMC) if supported)
or sees the MAC/DMA registers: e.g. using: ethtool -d ethX

Compiling the Kernel with CONFIG_DEBUG_FS and enabling the
STMMAC_DEBUG_FS option the driver will export the following
debugfs entries:

/sys/kernel/debug/stmmaceth/descriptors_status
  To show the DMA TX/RX descriptor rings

Developer can also use the "debug" module parameter to get
further debug information.

In the end, there are other macros (that cannot be enabled
via menuconfig) to turn-on the RX/TX DMA debugging,
specific MAC core debug printk etc. Others to enable the
debug in the TX and RX processes.
All these are only useful during the developing stage
and should never enabled inside the code for general usage.
In fact, these can generate an huge amount of debug messages.

6) Energy Efficient Ethernet

Energy Efficient Ethernet(EEE) enables IEEE 802.3 MAC sublayer along
with a family of Physical layer to operate in the Low power Idle(LPI)
mode. The EEE mode supports the IEEE 802.3 MAC operation at 100Mbps,
1000Mbps & 10Gbps.

The LPI mode allows power saving by switching off parts of the
communication device functionality when there is no data to be
transmitted & received. The system on both the side of the link can
disable some functionalities & save power during the period of low-link
utilization. The MAC controls whether the system should enter or exit
the LPI mode & communicate this to PHY.

As soon as the interface is opened, the driver verifies if the EEE can
be supported. This is done by looking at both the DMA HW capability
register and the PHY devices MCD registers.
To enter in Tx LPI mode the driver needs to have a software timer
that enable and disable the LPI mode when there is nothing to be
transmitted.

7) Extended descriptors
The extended descriptors give us information about the receive Ethernet payload
when it is carrying PTP packets or TCP/UDP/ICMP over IP.
These are not available on GMAC Synopsys chips older than the 3.50.
At probe time the driver will decide if these can be actually used.
This support also is mandatory for PTPv2 because the extra descriptors 6 and 7
are used for saving the hardware timestamps.

8) Precision Time Protocol (PTP)
The driver supports the IEEE 1588-2002, Precision Time Protocol (PTP),
which enables precise synchronization of clocks in measurement and
control systems implemented with technologies such as network
communication.

In addition to the basic timestamp features mentioned in IEEE 1588-2002
Timestamps, new GMAC cores support the advanced timestamp features.
IEEE 1588-2008 that can be enabled when configure the Kernel.

9) SGMII/RGMII supports
New GMAC devices provide own way to manage RGMII/SGMII.
This information is available at run-time by looking at the
HW capability register. This means that the stmmac can manage
auto-negotiation and link status w/o using the PHYLIB stuff
In fact, the HW provides a subset of extended registers to
restart the ANE, verify Full/Half duplex mode and Speed.
Also thanks to these registers it is possible to look at the
Auto-negotiated Link Parter Ability.

10) TODO:
 o XGMAC is not supported.
 o Complete the TBI & RTBI support.
 o extend VLAN support for 3.70a SYNP GMAC.