summaryrefslogtreecommitdiffstats
path: root/Documentation/driver-api/gpio/driver.rst
blob: bbc53920d4dd699bcb62f88a3c528b299876cfbc (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
=====================
GPIO Driver Interface
=====================

This document serves as a guide for writers of GPIO chip drivers.

Each GPIO controller driver needs to include the following header, which defines
the structures used to define a GPIO driver::

	#include <linux/gpio/driver.h>


Internal Representation of GPIOs
================================

A GPIO chip handles one or more GPIO lines. To be considered a GPIO chip, the
lines must conform to the definition: General Purpose Input/Output. If the
line is not general purpose, it is not GPIO and should not be handled by a
GPIO chip. The use case is the indicative: certain lines in a system may be
called GPIO but serve a very particular purpose thus not meeting the criteria
of a general purpose I/O. On the other hand a LED driver line may be used as a
GPIO and should therefore still be handled by a GPIO chip driver.

Inside a GPIO driver, individual GPIO lines are identified by their hardware
number, sometime also referred to as ``offset``, which is a unique number
between 0 and n-1, n being the number of GPIOs managed by the chip.

The hardware GPIO number should be something intuitive to the hardware, for
example if a system uses a memory-mapped set of I/O-registers where 32 GPIO
lines are handled by one bit per line in a 32-bit register, it makes sense to
use hardware offsets 0..31 for these, corresponding to bits 0..31 in the
register.

This number is purely internal: the hardware number of a particular GPIO
line is never made visible outside of the driver.

On top of this internal number, each GPIO line also needs to have a global
number in the integer GPIO namespace so that it can be used with the legacy GPIO
interface. Each chip must thus have a "base" number (which can be automatically
assigned), and for each GPIO line the global number will be (base + hardware
number). Although the integer representation is considered deprecated, it still
has many users and thus needs to be maintained.

So for example one platform could use global numbers 32-159 for GPIOs, with a
controller defining 128 GPIOs at a "base" of 32 ; while another platform uses
global numbers 0..63 with one set of GPIO controllers, 64-79 with another type
of GPIO controller, and on one particular board 80-95 with an FPGA. The legacy
numbers need not be contiguous; either of those platforms could also use numbers
2000-2063 to identify GPIO lines in a bank of I2C GPIO expanders.


Controller Drivers: gpio_chip
=============================

In the gpiolib framework each GPIO controller is packaged as a "struct
gpio_chip" (see <linux/gpio/driver.h> for its complete definition) with members
common to each controller of that type, these should be assigned by the
driver code:

 - methods to establish GPIO line direction
 - methods used to access GPIO line values
 - method to set electrical configuration for a given GPIO line
 - method to return the IRQ number associated to a given GPIO line
 - flag saying whether calls to its methods may sleep
 - optional line names array to identify lines
 - optional debugfs dump method (showing extra state information)
 - optional base number (will be automatically assigned if omitted)
 - optional label for diagnostics and GPIO chip mapping using platform data

The code implementing a gpio_chip should support multiple instances of the
controller, preferably using the driver model. That code will configure each
gpio_chip and issue gpiochip_add(), gpiochip_add_data(), or
devm_gpiochip_add_data().  Removing a GPIO controller should be rare; use
gpiochip_remove() when it is unavoidable.

Often a gpio_chip is part of an instance-specific structure with states not
exposed by the GPIO interfaces, such as addressing, power management, and more.
Chips such as audio codecs will have complex non-GPIO states.

Any debugfs dump method should normally ignore lines which haven't been
requested. They can use gpiochip_is_requested(), which returns either
NULL or the label associated with that GPIO line when it was requested.

Realtime considerations: the GPIO driver should not use spinlock_t or any
sleepable APIs (like PM runtime) in its gpio_chip implementation (.get/.set
and direction control callbacks) if it is expected to call GPIO APIs from
atomic context on realtime kernels (inside hard IRQ handlers and similar
contexts). Normally this should not be required.


GPIO electrical configuration
-----------------------------

GPIO lines can be configured for several electrical modes of operation by using
the .set_config() callback. Currently this API supports setting:

- Debouncing
- Single-ended modes (open drain/open source)
- Pull up and pull down resistor enablement

These settings are described below.

The .set_config() callback uses the same enumerators and configuration
semantics as the generic pin control drivers. This is not a coincidence: it is
possible to assign the .set_config() to the function gpiochip_generic_config()
which will result in pinctrl_gpio_set_config() being called and eventually
ending up in the pin control back-end "behind" the GPIO controller, usually
closer to the actual pins. This way the pin controller can manage the below
listed GPIO configurations.

If a pin controller back-end is used, the GPIO controller or hardware
description needs to provide "GPIO ranges" mapping the GPIO line offsets to pin
numbers on the pin controller so they can properly cross-reference each other.


GPIO lines with debounce support
--------------------------------

Debouncing is a configuration set to a pin indicating that it is connected to
a mechanical switch or button, or similar that may bounce. Bouncing means the
line is pulled high/low quickly at very short intervals for mechanical
reasons. This can result in the value being unstable or irqs fireing repeatedly
unless the line is debounced.

Debouncing in practice involves setting up a timer when something happens on
the line, wait a little while and then sample the line again, so see if it
still has the same value (low or high). This could also be repeated by a clever
state machine, waiting for a line to become stable. In either case, it sets
a certain number of milliseconds for debouncing, or just "on/off" if that time
is not configurable.


GPIO lines with open drain/source support
-----------------------------------------

Open drain (CMOS) or open collector (TTL) means the line is not actively driven
high: instead you provide the drain/collector as output, so when the transistor
is not open, it will present a high-impedance (tristate) to the external rail::


   CMOS CONFIGURATION      TTL CONFIGURATION

            ||--- out              +--- out
     in ----||                   |/
            ||--+         in ----|
                |                |\
               GND	           GND

This configuration is normally used as a way to achieve one of two things:

- Level-shifting: to reach a logical level higher than that of the silicon
  where the output resides.

- Inverse wire-OR on an I/O line, for example a GPIO line, making it possible
  for any driving stage on the line to drive it low even if any other output
  to the same line is simultaneously driving it high. A special case of this
  is driving the SCL and SDA lines of an I2C bus, which is by definition a
  wire-OR bus.

Both use cases require that the line be equipped with a pull-up resistor. This
resistor will make the line tend to high level unless one of the transistors on
the rail actively pulls it down.

The level on the line will go as high as the VDD on the pull-up resistor, which
may be higher than the level supported by the transistor, achieving a
level-shift to the higher VDD.

Integrated electronics often have an output driver stage in the form of a CMOS
"totem-pole" with one N-MOS and one P-MOS transistor where one of them drives
the line high and one of them drives the line low. This is called a push-pull
output. The "totem-pole" looks like so::

                     VDD
                      |
            OD    ||--+
         +--/ ---o||     P-MOS-FET
         |        ||--+
    IN --+            +----- out
         |        ||--+
         +--/ ----||     N-MOS-FET
            OS    ||--+
                      |
                     GND

The desired output signal (e.g. coming directly from some GPIO output register)
arrives at IN. The switches named "OD" and "OS" are normally closed, creating
a push-pull circuit.

Consider the little "switches" named "OD" and "OS" that enable/disable the
P-MOS or N-MOS transistor right after the split of the input. As you can see,
either transistor will go totally numb if this switch is open. The totem-pole
is then halved and give high impedance instead of actively driving the line
high or low respectively. That is usually how software-controlled open
drain/source works.

Some GPIO hardware come in open drain / open source configuration. Some are
hard-wired lines that will only support open drain or open source no matter
what: there is only one transistor there. Some are software-configurable:
by flipping a bit in a register the output can be configured as open drain
or open source, in practice by flicking open the switches labeled "OD" and "OS"
in the drawing above.

By disabling the P-MOS transistor, the output can be driven between GND and
high impedance (open drain), and by disabling the N-MOS transistor, the output
can be driven between VDD and high impedance (open source). In the first case,
a pull-up resistor is needed on the outgoing rail to complete the circuit, and
in the second case, a pull-down resistor is needed on the rail.

Hardware that supports open drain or open source or both, can implement a
special callback in the gpio_chip: .set_config() that takes a generic
pinconf packed value telling whether to configure the line as open drain,
open source or push-pull. This will happen in response to the
GPIO_OPEN_DRAIN or GPIO_OPEN_SOURCE flag set in the machine file, or coming
from other hardware descriptions.

If this state can not be configured in hardware, i.e. if the GPIO hardware does
not support open drain/open source in hardware, the GPIO library will instead
use a trick: when a line is set as output, if the line is flagged as open
drain, and the IN output value is low, it will be driven low as usual. But
if the IN output value is set to high, it will instead *NOT* be driven high,
instead it will be switched to input, as input mode is high impedance, thus
achieveing an "open drain emulation" of sorts: electrically the behaviour will
be identical, with the exception of possible hardware glitches when switching
the mode of the line.

For open source configuration the same principle is used, just that instead
of actively driving the line low, it is set to input.


GPIO lines with pull up/down resistor support
---------------------------------------------

A GPIO line can support pull-up/down using the .set_config() callback. This
means that a pull up or pull-down resistor is available on the output of the
GPIO line, and this resistor is software controlled.

In discrete designs, a pull-up or pull-down resistor is simply soldered on
the circuit board. This is not something we deal with or model in software. The
most you will think about these lines is that they will very likely be
configured as open drain or open source (see the section above).

The .set_config() callback can only turn pull up or down on and off, and will
no have any semantic knowledge about the resistance used. It will only say
switch a bit in a register enabling or disabling pull-up or pull-down.

If the GPIO line supports shunting in different resistance values for the
pull-up or pull-down resistor, the GPIO chip callback .set_config() will not
suffice. For these complex use cases, a combined GPIO chip and pin controller
need to be implemented, as the pin config interface of a pin controller
supports more versatile control over electrical properties and can handle
different pull-up or pull-down resistance values.


GPIO drivers providing IRQs
===========================

It is custom that GPIO drivers (GPIO chips) are also providing interrupts,
most often cascaded off a parent interrupt controller, and in some special
cases the GPIO logic is melded with a SoC's primary interrupt controller.

The IRQ portions of the GPIO block are implemented using an irq_chip, using
the header <linux/irq.h>. So this combined driver is utilizing two sub-
systems simultaneously: gpio and irq.

It is legal for any IRQ consumer to request an IRQ from any irqchip even if it
is a combined GPIO+IRQ driver. The basic premise is that gpio_chip and
irq_chip are orthogonal, and offering their services independent of each
other.

gpiod_to_irq() is just a convenience function to figure out the IRQ for a
certain GPIO line and should not be relied upon to have been called before
the IRQ is used.

Always prepare the hardware and make it ready for action in respective
callbacks from the GPIO and irq_chip APIs. Do not rely on gpiod_to_irq() having
been called first.

We can divide GPIO irqchips in two broad categories:

- CASCADED INTERRUPT CHIPS: this means that the GPIO chip has one common
  interrupt output line, which is triggered by any enabled GPIO line on that
  chip. The interrupt output line will then be routed to an parent interrupt
  controller one level up, in the most simple case the systems primary
  interrupt controller. This is modeled by an irqchip that will inspect bits
  inside the GPIO controller to figure out which line fired it. The irqchip
  part of the driver needs to inspect registers to figure this out and it
  will likely also need to acknowledge that it is handling the interrupt
  by clearing some bit (sometime implicitly, by just reading a status
  register) and it will often need to set up the configuration such as
  edge sensitivity (rising or falling edge, or high/low level interrupt for
  example).

- HIERARCHICAL INTERRUPT CHIPS: this means that each GPIO line has a dedicated
  irq line to a parent interrupt controller one level up. There is no need
  to inquire the GPIO hardware to figure out which line has fired, but it
  may still be necessary to acknowledge the interrupt and set up configuration
  such as edge sensitivity.

Realtime considerations: a realtime compliant GPIO driver should not use
spinlock_t or any sleepable APIs (like PM runtime) as part of its irqchip
implementation.

- spinlock_t should be replaced with raw_spinlock_t.[1]
- If sleepable APIs have to be used, these can be done from the .irq_bus_lock()
  and .irq_bus_unlock() callbacks, as these are the only slowpath callbacks
  on an irqchip. Create the callbacks if needed.[2]


Cascaded GPIO irqchips
----------------------

Cascaded GPIO irqchips usually fall in one of three categories:

- CHAINED CASCADED GPIO IRQCHIPS: these are usually the type that is embedded on
  an SoC. This means that there is a fast IRQ flow handler for the GPIOs that
  gets called in a chain from the parent IRQ handler, most typically the
  system interrupt controller. This means that the GPIO irqchip handler will
  be called immediately from the parent irqchip, while holding the IRQs
  disabled. The GPIO irqchip will then end up calling something like this
  sequence in its interrupt handler::

    static irqreturn_t foo_gpio_irq(int irq, void *data)
        chained_irq_enter(...);
        generic_handle_irq(...);
        chained_irq_exit(...);

  Chained GPIO irqchips typically can NOT set the .can_sleep flag on
  struct gpio_chip, as everything happens directly in the callbacks: no
  slow bus traffic like I2C can be used.

  Realtime considerations: Note that chained IRQ handlers will not be forced
  threaded on -RT. As a result, spinlock_t or any sleepable APIs (like PM
  runtime) can't be used in a chained IRQ handler.

  If required (and if it can't be converted to the nested threaded GPIO irqchip,
  see below) a chained IRQ handler can be converted to generic irq handler and
  this way it will become a threaded IRQ handler on -RT and a hard IRQ handler
  on non-RT (for example, see [3]).

  The generic_handle_irq() is expected to be called with IRQ disabled,
  so the IRQ core will complain if it is called from an IRQ handler which is
  forced to a thread. The "fake?" raw lock can be used to work around this
  problem::

    raw_spinlock_t wa_lock;
    static irqreturn_t omap_gpio_irq_handler(int irq, void *gpiobank)
        unsigned long wa_lock_flags;
        raw_spin_lock_irqsave(&bank->wa_lock, wa_lock_flags);
        generic_handle_irq(irq_find_mapping(bank->chip.irq.domain, bit));
        raw_spin_unlock_irqrestore(&bank->wa_lock, wa_lock_flags);

- GENERIC CHAINED GPIO IRQCHIPS: these are the same as "CHAINED GPIO irqchips",
  but chained IRQ handlers are not used. Instead GPIO IRQs dispatching is
  performed by generic IRQ handler which is configured using request_irq().
  The GPIO irqchip will then end up calling something like this sequence in
  its interrupt handler::

    static irqreturn_t gpio_rcar_irq_handler(int irq, void *dev_id)
        for each detected GPIO IRQ
            generic_handle_irq(...);

  Realtime considerations: this kind of handlers will be forced threaded on -RT,
  and as result the IRQ core will complain that generic_handle_irq() is called
  with IRQ enabled and the same work-around as for "CHAINED GPIO irqchips" can
  be applied.

- NESTED THREADED GPIO IRQCHIPS: these are off-chip GPIO expanders and any
  other GPIO irqchip residing on the other side of a sleeping bus such as I2C
  or SPI.

  Of course such drivers that need slow bus traffic to read out IRQ status and
  similar, traffic which may in turn incur other IRQs to happen, cannot be
  handled in a quick IRQ handler with IRQs disabled. Instead they need to spawn
  a thread and then mask the parent IRQ line until the interrupt is handled
  by the driver. The hallmark of this driver is to call something like
  this in its interrupt handler::

    static irqreturn_t foo_gpio_irq(int irq, void *data)
        ...
        handle_nested_irq(irq);

  The hallmark of threaded GPIO irqchips is that they set the .can_sleep
  flag on struct gpio_chip to true, indicating that this chip may sleep
  when accessing the GPIOs.

  These kinds of irqchips are inherently realtime tolerant as they are
  already set up to handle sleeping contexts.


Infrastructure helpers for GPIO irqchips
----------------------------------------

To help out in handling the set-up and management of GPIO irqchips and the
associated irqdomain and resource allocation callbacks. These are activated
by selecting the Kconfig symbol GPIOLIB_IRQCHIP. If the symbol
IRQ_DOMAIN_HIERARCHY is also selected, hierarchical helpers will also be
provided. A big portion of overhead code will be managed by gpiolib,
under the assumption that your interrupts are 1-to-1-mapped to the
GPIO line index:

.. csv-table::
    :header: GPIO line offset, Hardware IRQ

    0,0
    1,1
    2,2
    ...,...
    ngpio-1, ngpio-1


If some GPIO lines do not have corresponding IRQs, the bitmask valid_mask
and the flag need_valid_mask in gpio_irq_chip can be used to mask off some
lines as invalid for associating with IRQs.

The preferred way to set up the helpers is to fill in the
struct gpio_irq_chip inside struct gpio_chip before adding the gpio_chip.
If you do this, the additional irq_chip will be set up by gpiolib at the
same time as setting up the rest of the GPIO functionality. The following
is a typical example of a chained cascaded interrupt handler using
the gpio_irq_chip:

.. code-block:: c

  /* Typical state container with dynamic irqchip */
  struct my_gpio {
      struct gpio_chip gc;
      struct irq_chip irq;
  };

  int irq; /* from platform etc */
  struct my_gpio *g;
  struct gpio_irq_chip *girq;

  /* Set up the irqchip dynamically */
  g->irq.name = "my_gpio_irq";
  g->irq.irq_ack = my_gpio_ack_irq;
  g->irq.irq_mask = my_gpio_mask_irq;
  g->irq.irq_unmask = my_gpio_unmask_irq;
  g->irq.irq_set_type = my_gpio_set_irq_type;

  /* Get a pointer to the gpio_irq_chip */
  girq = &g->gc.irq;
  girq->chip = &g->irq;
  girq->parent_handler = ftgpio_gpio_irq_handler;
  girq->num_parents = 1;
  girq->parents = devm_kcalloc(dev, 1, sizeof(*girq->parents),
                               GFP_KERNEL);
  if (!girq->parents)
      return -ENOMEM;
  girq->default_type = IRQ_TYPE_NONE;
  girq->handler = handle_bad_irq;
  girq->parents[0] = irq;

  return devm_gpiochip_add_data(dev, &g->gc, g);

The helper supports using threaded interrupts as well. Then you just request
the interrupt separately and go with it:

.. code-block:: c

  /* Typical state container with dynamic irqchip */
  struct my_gpio {
      struct gpio_chip gc;
      struct irq_chip irq;
  };

  int irq; /* from platform etc */
  struct my_gpio *g;
  struct gpio_irq_chip *girq;

  /* Set up the irqchip dynamically */
  g->irq.name = "my_gpio_irq";
  g->irq.irq_ack = my_gpio_ack_irq;
  g->irq.irq_mask = my_gpio_mask_irq;
  g->irq.irq_unmask = my_gpio_unmask_irq;
  g->irq.irq_set_type = my_gpio_set_irq_type;

  ret = devm_request_threaded_irq(dev, irq, NULL,
		irq_thread_fn, IRQF_ONESHOT, "my-chip", g);
  if (ret < 0)
	return ret;

  /* Get a pointer to the gpio_irq_chip */
  girq = &g->gc.irq;
  girq->chip = &g->irq;
  /* This will let us handle the parent IRQ in the driver */
  girq->parent_handler = NULL;
  girq->num_parents = 0;
  girq->parents = NULL;
  girq->default_type = IRQ_TYPE_NONE;
  girq->handler = handle_bad_irq;

  return devm_gpiochip_add_data(dev, &g->gc, g);

The helper supports using hierarchical interrupt controllers as well.
In this case the typical set-up will look like this:

.. code-block:: c

  /* Typical state container with dynamic irqchip */
  struct my_gpio {
      struct gpio_chip gc;
      struct irq_chip irq;
      struct fwnode_handle *fwnode;
  };

  int irq; /* from platform etc */
  struct my_gpio *g;
  struct gpio_irq_chip *girq;

  /* Set up the irqchip dynamically */
  g->irq.name = "my_gpio_irq";
  g->irq.irq_ack = my_gpio_ack_irq;
  g->irq.irq_mask = my_gpio_mask_irq;
  g->irq.irq_unmask = my_gpio_unmask_irq;
  g->irq.irq_set_type = my_gpio_set_irq_type;

  /* Get a pointer to the gpio_irq_chip */
  girq = &g->gc.irq;
  girq->chip = &g->irq;
  girq->default_type = IRQ_TYPE_NONE;
  girq->handler = handle_bad_irq;
  girq->fwnode = g->fwnode;
  girq->parent_domain = parent;
  girq->child_to_parent_hwirq = my_gpio_child_to_parent_hwirq;

  return devm_gpiochip_add_data(dev, &g->gc, g);

As you can see pretty similar, but you do not supply a parent handler for
the IRQ, instead a parent irqdomain, an fwnode for the hardware and
a funcion .child_to_parent_hwirq() that has the purpose of looking up
the parent hardware irq from a child (i.e. this gpio chip) hardware irq.
As always it is good to look at examples in the kernel tree for advice
on how to find the required pieces.

If there is a need to exclude certain GPIO lines from the IRQ domain handled by
these helpers, we can set .irq.need_valid_mask of the gpiochip before
devm_gpiochip_add_data() or gpiochip_add_data() is called. This allocates an
.irq.valid_mask with as many bits set as there are GPIO lines in the chip, each
bit representing line 0..n-1. Drivers can exclude GPIO lines by clearing bits
from this mask. The mask can be filled in the init_valid_mask() callback
that is part of the struct gpio_irq_chip.

To use the helpers please keep the following in mind:

- Make sure to assign all relevant members of the struct gpio_chip so that
  the irqchip can initialize. E.g. .dev and .can_sleep shall be set up
  properly.

- Nominally set gpio_irq_chip.handler to handle_bad_irq. Then, if your irqchip
  is cascaded, set the handler to handle_level_irq() and/or handle_edge_irq()
  in the irqchip .set_type() callback depending on what your controller
  supports and what is requested by the consumer.


Locking IRQ usage
-----------------

Since GPIO and irq_chip are orthogonal, we can get conflicts between different
use cases. For example a GPIO line used for IRQs should be an input line,
it does not make sense to fire interrupts on an output GPIO.

If there is competition inside the subsystem which side is using the
resource (a certain GPIO line and register for example) it needs to deny
certain operations and keep track of usage inside of the gpiolib subsystem.

Input GPIOs can be used as IRQ signals. When this happens, a driver is requested
to mark the GPIO as being used as an IRQ::

	int gpiochip_lock_as_irq(struct gpio_chip *chip, unsigned int offset)

This will prevent the use of non-irq related GPIO APIs until the GPIO IRQ lock
is released::

	void gpiochip_unlock_as_irq(struct gpio_chip *chip, unsigned int offset)

When implementing an irqchip inside a GPIO driver, these two functions should
typically be called in the .startup() and .shutdown() callbacks from the
irqchip.

When using the gpiolib irqchip helpers, these callbacks are automatically
assigned.


Disabling and enabling IRQs
---------------------------

In some (fringe) use cases, a driver may be using a GPIO line as input for IRQs,
but occasionally switch that line over to drive output and then back to being
an input with interrupts again. This happens on things like CEC (Consumer
Electronics Control).

When a GPIO is used as an IRQ signal, then gpiolib also needs to know if
the IRQ is enabled or disabled. In order to inform gpiolib about this,
the irqchip driver should call::

	void gpiochip_disable_irq(struct gpio_chip *chip, unsigned int offset)

This allows drivers to drive the GPIO as an output while the IRQ is
disabled. When the IRQ is enabled again, a driver should call::

	void gpiochip_enable_irq(struct gpio_chip *chip, unsigned int offset)

When implementing an irqchip inside a GPIO driver, these two functions should
typically be called in the .irq_disable() and .irq_enable() callbacks from the
irqchip.

When using the gpiolib irqchip helpers, these callbacks are automatically
assigned.


Real-Time compliance for GPIO IRQ chips
---------------------------------------

Any provider of irqchips needs to be carefully tailored to support Real-Time
preemption. It is desirable that all irqchips in the GPIO subsystem keep this
in mind and do the proper testing to assure they are real time-enabled.

So, pay attention on above realtime considerations in the documentation.

The following is a checklist to follow when preparing a driver for real-time
compliance:

- ensure spinlock_t is not used as part irq_chip implementation
- ensure that sleepable APIs are not used as part irq_chip implementation
  If sleepable APIs have to be used, these can be done from the .irq_bus_lock()
  and .irq_bus_unlock() callbacks
- Chained GPIO irqchips: ensure spinlock_t or any sleepable APIs are not used
  from the chained IRQ handler
- Generic chained GPIO irqchips: take care about generic_handle_irq() calls and
  apply corresponding work-around
- Chained GPIO irqchips: get rid of the chained IRQ handler and use generic irq
  handler if possible
- regmap_mmio: it is possible to disable internal locking in regmap by setting
  .disable_locking and handling the locking in the GPIO driver
- Test your driver with the appropriate in-kernel real-time test cases for both
  level and edge IRQs

* [1] http://www.spinics.net/lists/linux-omap/msg120425.html
* [2] https://lore.kernel.org/r/1443209283-20781-2-git-send-email-grygorii.strashko@ti.com
* [3] https://lore.kernel.org/r/1443209283-20781-3-git-send-email-grygorii.strashko@ti.com


Requesting self-owned GPIO pins
===============================

Sometimes it is useful to allow a GPIO chip driver to request its own GPIO
descriptors through the gpiolib API. A GPIO driver can use the following
functions to request and free descriptors::

	struct gpio_desc *gpiochip_request_own_desc(struct gpio_desc *desc,
						    u16 hwnum,
						    const char *label,
						    enum gpiod_flags flags)

	void gpiochip_free_own_desc(struct gpio_desc *desc)

Descriptors requested with gpiochip_request_own_desc() must be released with
gpiochip_free_own_desc().

These functions must be used with care since they do not affect module use
count. Do not use the functions to request gpio descriptors not owned by the
calling driver.