1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
|
Renesas Electronics USBHS driver
Required properties:
- compatible: Must contain one or more of the following:
- "renesas,usbhs-r8a7743" for r8a7743 (RZ/G1M) compatible device
- "renesas,usbhs-r8a7744" for r8a7744 (RZ/G1N) compatible device
- "renesas,usbhs-r8a7745" for r8a7745 (RZ/G1E) compatible device
- "renesas,usbhs-r8a774a1" for r8a774a1 (RZ/G2M) compatible device
- "renesas,usbhs-r8a774c0" for r8a774c0 (RZ/G2E) compatible device
- "renesas,usbhs-r8a7790" for r8a7790 (R-Car H2) compatible device
- "renesas,usbhs-r8a7791" for r8a7791 (R-Car M2-W) compatible device
- "renesas,usbhs-r8a7792" for r8a7792 (R-Car V2H) compatible device
- "renesas,usbhs-r8a7793" for r8a7793 (R-Car M2-N) compatible device
- "renesas,usbhs-r8a7794" for r8a7794 (R-Car E2) compatible device
- "renesas,usbhs-r8a7795" for r8a7795 (R-Car H3) compatible device
- "renesas,usbhs-r8a7796" for r8a7796 (R-Car M3-W) compatible device
- "renesas,usbhs-r8a77965" for r8a77965 (R-Car M3-N) compatible device
- "renesas,usbhs-r8a77990" for r8a77990 (R-Car E3) compatible device
- "renesas,usbhs-r8a77995" for r8a77995 (R-Car D3) compatible device
- "renesas,usbhs-r7s72100" for r7s72100 (RZ/A1) compatible device
- "renesas,rcar-gen2-usbhs" for R-Car Gen2 or RZ/G1 compatible devices
- "renesas,rcar-gen3-usbhs" for R-Car Gen3 or RZ/G2 compatible devices
- "renesas,rza1-usbhs" for RZ/A1 compatible device
When compatible with the generic version, nodes must list the
SoC-specific version corresponding to the platform first followed
by the generic version.
- reg: Base address and length of the register for the USBHS
- interrupts: Interrupt specifier for the USBHS
- clocks: A list of phandle + clock specifier pairs.
- In case of "renesas,rcar-gen3-usbhs", two clocks are required.
First clock should be peripheral and second one should be host.
- In case of except above, one clock is required. First clock
should be peripheral.
Optional properties:
- renesas,buswait: Integer to use BUSWAIT register
- renesas,enable-gpio: A gpio specifier to check GPIO determining if USB
function should be enabled
- phys: phandle + phy specifier pair
- phy-names: must be "usb"
- dmas: Must contain a list of references to DMA specifiers.
- dma-names : named "ch%d", where %d is the channel number ranging from zero
to the number of channels (DnFIFOs) minus one.
Example:
usbhs: usb@e6590000 {
compatible = "renesas,usbhs-r8a7790", "renesas,rcar-gen2-usbhs";
reg = <0 0xe6590000 0 0x100>;
interrupts = <0 107 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp7_clks R8A7790_CLK_HSUSB>;
};
|
