1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
|
* Renesas R-Car generation 3 USB 2.0 PHY
This file provides information on what the device node for the R-Car generation
3, RZ/G1C, RZ/G2 and RZ/A2 USB 2.0 PHY contain.
Required properties:
- compatible: "renesas,usb2-phy-r7s9210" if the device is a part of an R7S9210
SoC.
"renesas,usb2-phy-r8a77470" if the device is a part of an R8A77470
SoC.
"renesas,usb2-phy-r8a774a1" if the device is a part of an R8A774A1
SoC.
"renesas,usb2-phy-r8a774c0" if the device is a part of an R8A774C0
SoC.
"renesas,usb2-phy-r8a7795" if the device is a part of an R8A7795
SoC.
"renesas,usb2-phy-r8a7796" if the device is a part of an R8A7796
SoC.
"renesas,usb2-phy-r8a77965" if the device is a part of an
R8A77965 SoC.
"renesas,usb2-phy-r8a77990" if the device is a part of an
R8A77990 SoC.
"renesas,usb2-phy-r8a77995" if the device is a part of an
R8A77995 SoC.
"renesas,rcar-gen3-usb2-phy" for a generic R-Car Gen3, RZ/G2 or
RZ/A2 compatible device.
When compatible with the generic version, nodes must list the
SoC-specific version corresponding to the platform first
followed by the generic version.
- reg: offset and length of the partial USB 2.0 Host register block.
- clocks: clock phandle and specifier pair(s).
- #phy-cells: see phy-bindings.txt in the same directory, must be <1> (and
using <0> is deprecated).
The phandle's argument in the PHY specifier is the INT_STATUS bit of controller:
- 1 = USBH_INTA (OHCI)
- 2 = USBH_INTB (EHCI)
- 3 = UCOM_INT (OTG and BC)
Optional properties:
To use a USB channel where USB 2.0 Host and HSUSB (USB 2.0 Peripheral) are
combined, the device tree node should set interrupt properties to use the
channel as USB OTG:
- interrupts: interrupt specifier for the PHY.
- vbus-supply: Phandle to a regulator that provides power to the VBUS. This
regulator will be managed during the PHY power on/off sequence.
- renesas,no-otg-pins: boolean, specify when a board does not provide proper
otg pins.
- dr_mode: string, indicates the working mode for the PHY. Can be "host",
"peripheral", or "otg". Should be set if otg controller is not used.
Example (R-Car H3):
usb-phy@ee080200 {
compatible = "renesas,usb2-phy-r8a7795", "renesas,rcar-gen3-usb2-phy";
reg = <0 0xee080200 0 0x700>;
interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 703>;
};
usb-phy@ee0a0200 {
compatible = "renesas,usb2-phy-r8a7795", "renesas,rcar-gen3-usb2-phy";
reg = <0 0xee0a0200 0 0x700>;
clocks = <&cpg CPG_MOD 702>;
};
|
