summaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt
blob: 017128394a3e2dff0ba371de06688f3a88f81c9d (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
* Qualcomm Atheros ath10k wireless devices

Required properties:
- compatible: Should be one of the following:
	* "qcom,ath10k"
	* "qcom,ipq4019-wifi"
	* "qcom,wcn3990-wifi"

PCI based devices uses compatible string "qcom,ath10k" and takes calibration
data along with board specific data via "qcom,ath10k-calibration-data".
Rest of the properties are not applicable for PCI based devices.

AHB based devices (i.e. ipq4019) uses compatible string "qcom,ipq4019-wifi"
and also uses most of the properties defined in this doc (except
"qcom,ath10k-calibration-data"). It uses "qcom,ath10k-pre-calibration-data"
to carry pre calibration data.

In general, entry "qcom,ath10k-pre-calibration-data" and
"qcom,ath10k-calibration-data" conflict with each other and only one
can be provided per device.

SNOC based devices (i.e. wcn3990) uses compatible string "qcom,wcn3990-wifi".

- reg: Address and length of the register set for the device.
- reg-names: Must include the list of following reg names,
	     "membase"
- interrupts: reference to the list of 17 interrupt numbers for "qcom,ipq4019-wifi"
	      compatible target.
	      reference to the list of 12 interrupt numbers for "qcom,wcn3990-wifi"
	      compatible target.
	      Must contain interrupt-names property per entry for
	      "qcom,ath10k", "qcom,ipq4019-wifi" compatible targets.

- interrupt-names: Must include the entries for MSI interrupt
		   names ("msi0" to "msi15") and legacy interrupt
		   name ("legacy") for "qcom,ath10k", "qcom,ipq4019-wifi"
		   compatible targets.

Optional properties:
- resets: Must contain an entry for each entry in reset-names.
          See ../reset/reseti.txt for details.
- reset-names: Must include the list of following reset names,
	       "wifi_cpu_init"
	       "wifi_radio_srif"
	       "wifi_radio_warm"
	       "wifi_radio_cold"
	       "wifi_core_warm"
	       "wifi_core_cold"
- clocks: List of clock specifiers, must contain an entry for each required
          entry in clock-names.
- clock-names: Should contain the clock names "wifi_wcss_cmd", "wifi_wcss_ref",
	       "wifi_wcss_rtc" for "qcom,ipq4019-wifi" compatible target and
	       "cxo_ref_clk_pin" for "qcom,wcn3990-wifi"
	       compatible target.
- qcom,msi_addr: MSI interrupt address.
- qcom,msi_base: Base value to add before writing MSI data into
		MSI address register.
- qcom,ath10k-calibration-variant: string to search for in the board-2.bin
				   variant list with the same bus and device
				   specific ids
- qcom,ath10k-calibration-data : calibration data + board specific data
				 as an array, the length can vary between
				 hw versions.
- qcom,ath10k-pre-calibration-data : pre calibration data as an array,
				     the length can vary between hw versions.
- <supply-name>-supply: handle to the regulator device tree node
			   optional "supply-name" are "vdd-0.8-cx-mx",
			   "vdd-1.8-xo", "vdd-1.3-rfa" and "vdd-3.3-ch0".
- memory-region:
	Usage: optional
	Value type: <phandle>
	Definition: reference to the reserved-memory for the msa region
		    used by the wifi firmware running in Q6.
- iommus:
	Usage: optional
	Value type: <prop-encoded-array>
	Definition: A list of phandle and IOMMU specifier pairs.
- ext-fem-name:
	Usage: Optional
	Value type: string
	Definition: Name of external front end module used. Some valid FEM names
		    for example: "microsemi-lx5586", "sky85703-11"
		    and "sky85803" etc.
- qcom,snoc-host-cap-8bit-quirk:
	Usage: Optional
	Value type: <empty>
	Definition: Quirk specifying that the firmware expects the 8bit version
		    of the host capability QMI request
- qcom,xo-cal-data: xo cal offset to be configured in xo trim register.

Example (to supply PCI based wifi block details):

In this example, the node is defined as child node of the PCI controller.

pci {
	pcie@0 {
		reg = <0 0 0 0 0>;
		#interrupt-cells = <1>;
		#size-cells = <2>;
		#address-cells = <3>;
		device_type = "pci";

		wifi@0,0 {
			reg = <0 0 0 0 0>;
			qcom,ath10k-calibration-data = [ 01 02 03 ... ];
			ext-fem-name = "microsemi-lx5586";
		};
	};
};

Example (to supply ipq4019 SoC wifi block details):

wifi0: wifi@a000000 {
	compatible = "qcom,ipq4019-wifi";
	reg = <0xa000000 0x200000>;
	resets = <&gcc WIFI0_CPU_INIT_RESET>,
		 <&gcc WIFI0_RADIO_SRIF_RESET>,
		 <&gcc WIFI0_RADIO_WARM_RESET>,
		 <&gcc WIFI0_RADIO_COLD_RESET>,
		 <&gcc WIFI0_CORE_WARM_RESET>,
		 <&gcc WIFI0_CORE_COLD_RESET>;
	reset-names = "wifi_cpu_init",
		      "wifi_radio_srif",
		      "wifi_radio_warm",
		      "wifi_radio_cold",
		      "wifi_core_warm",
		      "wifi_core_cold";
	clocks = <&gcc GCC_WCSS2G_CLK>,
		 <&gcc GCC_WCSS2G_REF_CLK>,
		 <&gcc GCC_WCSS2G_RTC_CLK>;
	clock-names = "wifi_wcss_cmd",
		      "wifi_wcss_ref",
		      "wifi_wcss_rtc";
	interrupts = <0 0x20 0x1>,
		     <0 0x21 0x1>,
		     <0 0x22 0x1>,
		     <0 0x23 0x1>,
		     <0 0x24 0x1>,
		     <0 0x25 0x1>,
		     <0 0x26 0x1>,
		     <0 0x27 0x1>,
		     <0 0x28 0x1>,
		     <0 0x29 0x1>,
		     <0 0x2a 0x1>,
		     <0 0x2b 0x1>,
		     <0 0x2c 0x1>,
		     <0 0x2d 0x1>,
		     <0 0x2e 0x1>,
		     <0 0x2f 0x1>,
		     <0 0xa8 0x0>;
	interrupt-names = "msi0",  "msi1",  "msi2",  "msi3",
			  "msi4",  "msi5",  "msi6",  "msi7",
			  "msi8",  "msi9",  "msi10", "msi11",
			  "msi12", "msi13", "msi14", "msi15",
			  "legacy";
	qcom,msi_addr = <0x0b006040>;
	qcom,msi_base = <0x40>;
	qcom,ath10k-pre-calibration-data = [ 01 02 03 ... ];
};

Example (to supply wcn3990 SoC wifi block details):

wifi@18000000 {
		compatible = "qcom,wcn3990-wifi";
		reg = <0x18800000 0x800000>;
		reg-names = "membase";
		clocks = <&clock_gcc clk_rf_clk2_pin>;
		clock-names = "cxo_ref_clk_pin";
		interrupts =
			<GIC_SPI 414 IRQ_TYPE_LEVEL_HIGH>,
			<GIC_SPI 415 IRQ_TYPE_LEVEL_HIGH>,
			<GIC_SPI 416 IRQ_TYPE_LEVEL_HIGH>,
			<GIC_SPI 417 IRQ_TYPE_LEVEL_HIGH>,
			<GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH>,
			<GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH>,
			<GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH>,
			<GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>,
			<GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH>,
			<GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH>,
			<GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>,
			<GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH>;
		vdd-0.8-cx-mx-supply = <&pm8998_l5>;
		vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
		vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
		vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
		memory-region = <&wifi_msa_mem>;
		iommus = <&apps_smmu 0x0040 0x1>;
};