1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
|
* Qualcomm Atheros ath10k wireless devices
Required properties:
- compatible: Should be one of the following:
* "qcom,ath10k"
* "qcom,ipq4019-wifi"
PCI based devices uses compatible string "qcom,ath10k" and takes calibration
data along with board specific data via "qcom,ath10k-calibration-data".
Rest of the properties are not applicable for PCI based devices.
AHB based devices (i.e. ipq4019) uses compatible string "qcom,ipq4019-wifi"
and also uses most of the properties defined in this doc (except
"qcom,ath10k-calibration-data"). It uses "qcom,ath10k-pre-calibration-data"
to carry pre calibration data.
In general, entry "qcom,ath10k-pre-calibration-data" and
"qcom,ath10k-calibration-data" conflict with each other and only one
can be provided per device.
Optional properties:
- reg: Address and length of the register set for the device.
- resets: Must contain an entry for each entry in reset-names.
See ../reset/reseti.txt for details.
- reset-names: Must include the list of following reset names,
"wifi_cpu_init"
"wifi_radio_srif"
"wifi_radio_warm"
"wifi_radio_cold"
"wifi_core_warm"
"wifi_core_cold"
- clocks: List of clock specifiers, must contain an entry for each required
entry in clock-names.
- clock-names: Should contain the clock names "wifi_wcss_cmd", "wifi_wcss_ref",
"wifi_wcss_rtc".
- interrupts: List of interrupt lines. Must contain an entry
for each entry in the interrupt-names property.
- interrupt-names: Must include the entries for MSI interrupt
names ("msi0" to "msi15") and legacy interrupt
name ("legacy"),
- qcom,msi_addr: MSI interrupt address.
- qcom,msi_base: Base value to add before writing MSI data into
MSI address register.
- qcom,ath10k-calibration-data : calibration data + board specific data
as an array, the length can vary between
hw versions.
- qcom,ath10k-pre-calibration-data : pre calibration data as an array,
the length can vary between hw versions.
Example (to supply the calibration data alone):
In this example, the node is defined as child node of the PCI controller.
pci {
pcie@0 {
reg = <0 0 0 0 0>;
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
device_type = "pci";
ath10k@0,0 {
reg = <0 0 0 0 0>;
device_type = "pci";
qcom,ath10k-calibration-data = [ 01 02 03 ... ];
};
};
};
Example (to supply ipq4019 SoC wifi block details):
wifi0: wifi@a000000 {
compatible = "qcom,ipq4019-wifi";
reg = <0xa000000 0x200000>;
resets = <&gcc WIFI0_CPU_INIT_RESET>,
<&gcc WIFI0_RADIO_SRIF_RESET>,
<&gcc WIFI0_RADIO_WARM_RESET>,
<&gcc WIFI0_RADIO_COLD_RESET>,
<&gcc WIFI0_CORE_WARM_RESET>,
<&gcc WIFI0_CORE_COLD_RESET>;
reset-names = "wifi_cpu_init",
"wifi_radio_srif",
"wifi_radio_warm",
"wifi_radio_cold",
"wifi_core_warm",
"wifi_core_cold";
clocks = <&gcc GCC_WCSS2G_CLK>,
<&gcc GCC_WCSS2G_REF_CLK>,
<&gcc GCC_WCSS2G_RTC_CLK>;
clock-names = "wifi_wcss_cmd",
"wifi_wcss_ref",
"wifi_wcss_rtc";
interrupts = <0 0x20 0x1>,
<0 0x21 0x1>,
<0 0x22 0x1>,
<0 0x23 0x1>,
<0 0x24 0x1>,
<0 0x25 0x1>,
<0 0x26 0x1>,
<0 0x27 0x1>,
<0 0x28 0x1>,
<0 0x29 0x1>,
<0 0x2a 0x1>,
<0 0x2b 0x1>,
<0 0x2c 0x1>,
<0 0x2d 0x1>,
<0 0x2e 0x1>,
<0 0x2f 0x1>,
<0 0xa8 0x0>;
interrupt-names = "msi0", "msi1", "msi2", "msi3",
"msi4", "msi5", "msi6", "msi7",
"msi8", "msi9", "msi10", "msi11",
"msi12", "msi13", "msi14", "msi15",
"legacy";
qcom,msi_addr = <0x0b006040>;
qcom,msi_base = <0x40>;
qcom,ath10k-pre-calibration-data = [ 01 02 03 ... ];
};
|
