1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
|
* Texas Instruments - dp83867 Giga bit ethernet phy
Required properties:
- reg - The ID number for the phy, usually a small integer
- ti,rx-internal-delay - RGMII Receive Clock Delay - see dt-bindings/net/ti-dp83867.h
for applicable values. Required only if interface type is
PHY_INTERFACE_MODE_RGMII_ID or PHY_INTERFACE_MODE_RGMII_RXID
- ti,tx-internal-delay - RGMII Transmit Clock Delay - see dt-bindings/net/ti-dp83867.h
for applicable values. Required only if interface type is
PHY_INTERFACE_MODE_RGMII_ID or PHY_INTERFACE_MODE_RGMII_TXID
Note: If the interface type is PHY_INTERFACE_MODE_RGMII the TX/RX clock delays
will be left at their default values, as set by the PHY's pin strapping.
The default strapping will use a delay of 2.00 ns. Thus
PHY_INTERFACE_MODE_RGMII, by default, does not behave as RGMII with no
internal delay, but as PHY_INTERFACE_MODE_RGMII_ID. The device tree
should use "rgmii-id" if internal delays are desired as this may be
changed in future to cause "rgmii" mode to disable delays.
Optional property:
- ti,min-output-impedance - MAC Interface Impedance control to set
the programmable output impedance to
minimum value (35 ohms).
- ti,max-output-impedance - MAC Interface Impedance control to set
the programmable output impedance to
maximum value (70 ohms).
- ti,dp83867-rxctrl-strap-quirk - This denotes the fact that the
board has RX_DV/RX_CTRL pin strapped in
mode 1 or 2. To ensure PHY operation,
there are specific actions that
software needs to take when this pin is
strapped in these modes. See data manual
for details.
- ti,clk-output-sel - Muxing option for CLK_OUT pin. See dt-bindings/net/ti-dp83867.h
for applicable values. The CLK_OUT pin can also
be disabled by this property. When omitted, the
PHY's default will be left as is.
- ti,sgmii-ref-clock-output-enable - This denotes which
SGMII configuration is used (4 or 6-wire modes).
Some MACs work with differential SGMII clock.
See data manual for details.
- ti,fifo-depth - Transmitt FIFO depth- see dt-bindings/net/ti-dp83867.h
for applicable values (deprecated)
-tx-fifo-depth - As defined in the ethernet-controller.yaml. Values for
the depth can be found in dt-bindings/net/ti-dp83867.h
-rx-fifo-depth - As defined in the ethernet-controller.yaml. Values for
the depth can be found in dt-bindings/net/ti-dp83867.h
Note: ti,min-output-impedance and ti,max-output-impedance are mutually
exclusive. When both properties are present ti,max-output-impedance
takes precedence.
Default child nodes are standard Ethernet PHY device
nodes as described in Documentation/devicetree/bindings/net/phy.txt
Example:
ethernet-phy@0 {
reg = <0>;
ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_75_NS>;
tx-fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
};
Datasheet can be found:
http://www.ti.com/product/DP83867IR/datasheet
|
