blob: 93a7469e70d4131fbc2d7f2daffd1917020709ee (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
|
* Qualcomm Atheros QCA8xxx switch family
Required properties:
- compatible: should be one of:
"qca,qca8334"
"qca,qca8337"
- #size-cells: must be 0
- #address-cells: must be 1
Subnodes:
The integrated switch subnode should be specified according to the binding
described in dsa/dsa.txt. If the QCA8K switch is connect to a SoC's external
mdio-bus each subnode describing a port needs to have a valid phandle
referencing the internal PHY it is connected to. This is because there's no
N:N mapping of port and PHY id.
Don't use mixed external and internal mdio-bus configurations, as this is
not supported by the hardware.
The CPU port of this switch is always port 0.
A CPU port node has the following optional node:
- fixed-link : Fixed-link subnode describing a link to a non-MDIO
managed entity. See
Documentation/devicetree/bindings/net/fixed-link.txt
for details.
For QCA8K the 'fixed-link' sub-node supports only the following properties:
- 'speed' (integer, mandatory), to indicate the link speed. Accepted
values are 10, 100 and 1000
- 'full-duplex' (boolean, optional), to indicate that full duplex is
used. When absent, half duplex is assumed.
Examples:
for the external mdio-bus configuration:
&mdio0 {
phy_port1: phy@0 {
reg = <0>;
};
phy_port2: phy@1 {
reg = <1>;
};
phy_port3: phy@2 {
reg = <2>;
};
phy_port4: phy@3 {
reg = <3>;
};
phy_port5: phy@4 {
reg = <4>;
};
switch@10 {
compatible = "qca,qca8337";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x10>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
label = "cpu";
ethernet = <&gmac1>;
phy-mode = "rgmii";
fixed-link {
speed = 1000;
full-duplex;
};
};
port@1 {
reg = <1>;
label = "lan1";
phy-handle = <&phy_port1>;
};
port@2 {
reg = <2>;
label = "lan2";
phy-handle = <&phy_port2>;
};
port@3 {
reg = <3>;
label = "lan3";
phy-handle = <&phy_port3>;
};
port@4 {
reg = <4>;
label = "lan4";
phy-handle = <&phy_port4>;
};
port@5 {
reg = <5>;
label = "wan";
phy-handle = <&phy_port5>;
};
};
};
};
for the internal master mdio-bus configuration:
&mdio0 {
switch@10 {
compatible = "qca,qca8337";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x10>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
label = "cpu";
ethernet = <&gmac1>;
phy-mode = "rgmii";
fixed-link {
speed = 1000;
full-duplex;
};
};
port@1 {
reg = <1>;
label = "lan1";
};
port@2 {
reg = <2>;
label = "lan2";
};
port@3 {
reg = <3>;
label = "lan3";
};
port@4 {
reg = <4>;
label = "lan4";
};
port@5 {
reg = <5>;
label = "wan";
};
};
};
};
|
