1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
|
* STMicroelectronics sdhci-st MMC/SD controller
This file documents the differences between the core properties in
Documentation/devicetree/bindings/mmc/mmc.txt and the properties
used by the sdhci-st driver.
Required properties:
- compatible: Must be "st,sdhci" and it can be compatible to "st,sdhci-stih407"
to set the internal glue logic used for configuring the MMC
subsystem (mmcss) inside the FlashSS (available in STiH407 SoC
family).
- clock-names: Should be "mmc" and "icn". (NB: The latter is not compulsory)
See: Documentation/devicetree/bindings/resource-names.txt
- clocks: Phandle to the clock.
See: Documentation/devicetree/bindings/clock/clock-bindings.txt
- interrupts: One mmc interrupt should be described here.
- interrupt-names: Should be "mmcirq".
- pinctrl-names: A pinctrl state names "default" must be defined.
- pinctrl-0: Phandle referencing pin configuration of the sd/emmc controller.
See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt
- reg: This must provide the host controller base address and it can also
contain the FlashSS Top register for TX/RX delay used by the driver
to configure DLL inside the flashSS, if so reg-names must also be
specified.
Optional properties:
- reg-names: Should be "mmc" and "top-mmc-delay". "top-mmc-delay" is optional
for eMMC on stih407 family silicon to configure DLL inside FlashSS.
- non-removable: Non-removable slot. Also used for configuring mmcss in STiH407 SoC
family.
See: Documentation/devicetree/bindings/mmc/mmc.txt.
- bus-width: Number of data lines.
See: Documentation/devicetree/bindings/mmc/mmc.txt.
- max-frequency: Can be 200MHz, 100MHz or 50MHz (default) and used for
configuring the CCONFIG3 in the mmcss.
See: Documentation/devicetree/bindings/mmc/mmc.txt.
- resets: Phandle and reset specifier pair to softreset line of HC IP.
See: Documentation/devicetree/bindings/reset/reset.txt
- vqmmc-supply: Phandle to the regulator dt node, mentioned as the vcc/vdd
supply in eMMC/SD specs.
- sd-uhs-sdr50: To enable the SDR50 in the mmcss.
See: Documentation/devicetree/bindings/mmc/mmc.txt.
- sd-uhs-sdr104: To enable the SDR104 in the mmcss.
See: Documentation/devicetree/bindings/mmc/mmc.txt.
- sd-uhs-ddr50: To enable the DDR50 in the mmcss.
See: Documentation/devicetree/bindings/mmc/mmc.txt.
Example:
/* Example stih416e eMMC configuration */
mmc0: sdhci@fe81e000 {
compatible = "st,sdhci";
status = "disabled";
reg = <0xfe81e000 0x1000>;
interrupts = <GIC_SPI 127 IRQ_TYPE_NONE>;
interrupt-names = "mmcirq";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_mmc0>;
clock-names = "mmc";
clocks = <&clk_s_a1_ls 1>;
bus-width = <8>
/* Example SD stih407 family configuration */
mmc1: sdhci@09080000 {
compatible = "st,sdhci-stih407", "st,sdhci";
status = "disabled";
reg = <0x09080000 0x7ff>;
reg-names = "mmc";
interrupts = <GIC_SPI 90 IRQ_TYPE_NONE>;
interrupt-names = "mmcirq";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_sd1>;
clock-names = "mmc";
clocks = <&clk_s_c0_flexgen CLK_MMC_1>;
resets = <&softreset STIH407_MMC1_SOFTRESET>;
bus-width = <4>;
};
/* Example eMMC stih407 family configuration */
mmc0: sdhci@09060000 {
compatible = "st,sdhci-stih407", "st,sdhci";
status = "disabled";
reg = <0x09060000 0x7ff>, <0x9061008 0x20>;
reg-names = "mmc", "top-mmc-delay";
interrupts = <GIC_SPI 92 IRQ_TYPE_NONE>;
interrupt-names = "mmcirq";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_mmc0>;
clock-names = "mmc";
clocks = <&clk_s_c0_flexgen CLK_MMC_0>;
vqmmc-supply = <&vmmc_reg>;
max-frequency = <200000000>;
bus-width = <8>;
non-removable;
sd-uhs-sdr50;
sd-uhs-sdr104;
sd-uhs-ddr50;
};
|
