summaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt
blob: 0fc6700ed8001093242460b75da24474cd2830b9 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
* Marvell EBU GPIO controller

Required properties:

- compatible : Should be "marvell,orion-gpio", "marvell,mv78200-gpio",
  "marvell,armadaxp-gpio" or "marvell,armada-8k-gpio".

    "marvell,orion-gpio" should be used for Orion, Kirkwood, Dove,
    Discovery (except MV78200) and Armada 370. "marvell,mv78200-gpio"
    should be used for the Discovery MV78200.

    "marvel,armadaxp-gpio" should be used for all Armada XP SoCs
    (MV78230, MV78260, MV78460).

    "marvell,armada-8k-gpio" should be used for the Armada 7K and 8K
    SoCs (either from AP or CP), see
    Documentation/devicetree/bindings/arm/marvell/ap80x-system-controller.txt
    for specific details about the offset property.

- reg: Address and length of the register set for the device. Only one
  entry is expected, except for the "marvell,armadaxp-gpio" variant
  for which two entries are expected: one for the general registers,
  one for the per-cpu registers. Not used for marvell,armada-8k-gpio.

- interrupts: The list of interrupts that are used for all the pins
  managed by this GPIO bank. There can be more than one interrupt
  (example: 1 interrupt per 8 pins on Armada XP, which means 4
  interrupts per bank of 32 GPIOs).

- interrupt-controller: identifies the node as an interrupt controller

- #interrupt-cells: specifies the number of cells needed to encode an
  interrupt source. Should be two.
  The first cell is the GPIO number.
  The second cell is used to specify flags:
    bits[3:0] trigger type and level flags:
      1 = low-to-high edge triggered.
      2 = high-to-low edge triggered.
      4 = active high level-sensitive.
      8 = active low level-sensitive.

- gpio-controller: marks the device node as a gpio controller

- ngpios: number of GPIOs this controller has

- #gpio-cells: Should be two. The first cell is the pin number. The
  second cell is reserved for flags, unused at the moment.

Optional properties:

In order to use the GPIO lines in PWM mode, some additional optional
properties are required.

- compatible: Must contain "marvell,armada-370-gpio"

- reg: an additional register set is needed, for the GPIO Blink
  Counter on/off registers.

- reg-names: Must contain an entry "pwm" corresponding to the
  additional register range needed for PWM operation.

- #pwm-cells: Should be two. The first cell is the GPIO line number. The
  second cell is the period in nanoseconds.

- clocks: Must be a phandle to the clock for the GPIO controller.

Example:

		gpio0: gpio@d0018100 {
			compatible = "marvell,armadaxp-gpio";
			reg = <0xd0018100 0x40>,
			    <0xd0018800 0x30>;
			ngpios = <32>;
			gpio-controller;
			#gpio-cells = <2>;
			interrupt-controller;
			#interrupt-cells = <2>;
			interrupts = <16>, <17>, <18>, <19>;
		};

		gpio1: gpio@18140 {
			compatible = "marvell,armada-370-gpio";
			reg = <0x18140 0x40>, <0x181c8 0x08>;
			reg-names = "gpio", "pwm";
			ngpios = <17>;
			gpio-controller;
			#gpio-cells = <2>;
			#pwm-cells = <2>;
			interrupt-controller;
			#interrupt-cells = <2>;
			interrupts = <87>, <88>, <89>;
			clocks = <&coreclk 0>;
		};