1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
|
# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
%YAML 1.2
---
$id: http://devicetree.org/schemas/bus/socionext,uniphier-system-bus.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: UniPhier System Bus
description: |
The UniPhier System Bus is an external bus that connects on-board devices to
the UniPhier SoC. It is a simple (semi-)parallel bus with address, data, and
some control signals. It supports up to 8 banks (chip selects).
Before any access to the bus, the bus controller must be configured; the bus
controller registers provide the control for the translation from the offset
within each bank to the CPU-viewed address. The needed setup includes the
base address, the size of each bank. Optionally, some timing parameters can
be optimized for faster bus access.
maintainers:
- Masahiro Yamada <yamada.masahiro@socionext.com>
properties:
compatible:
const: socionext,uniphier-system-bus
reg:
maxItems: 1
"#address-cells":
description: |
The first cell is the bank number (chip select).
The second cell is the address offset within the bank.
const: 2
"#size-cells":
const: 1
ranges:
description: |
Provide address translation from the System Bus to the parent bus.
Note:
The address region(s) that can be assigned for the System Bus is
implementation defined. Some SoCs can use 0x00000000-0x0fffffff and
0x40000000-0x4fffffff, while other SoCs only 0x40000000-0x4fffffff.
There might be additional limitations depending on SoCs and the boot mode.
The address translation is arbitrary as long as the banks are assigned in
the supported address space with the required alignment and they do not
overlap one another.
For example, it is possible to map:
bank 0 to 0x42000000-0x43ffffff, bank 5 to 0x46000000-0x46ffffff
It is also possible to map:
bank 0 to 0x48000000-0x49ffffff, bank 5 to 0x44000000-0x44ffffff
There is no reason to stick to a particular translation mapping, but the
"ranges" property should provide a "reasonable" default that is known to
work. The software should initialize the bus controller according to it.
required:
- compatible
- reg
- "#address-cells"
- "#size-cells"
- ranges
examples:
- |
// In this example,
// - the Ethernet device is connected at the offset 0x01f00000 of CS1 and
// mapped to 0x43f00000 of the parent bus.
// - the UART device is connected at the offset 0x00200000 of CS5 and
// mapped to 0x46200000 of the parent bus.
system-bus@58c00000 {
compatible = "socionext,uniphier-system-bus";
reg = <0x58c00000 0x400>;
#address-cells = <2>;
#size-cells = <1>;
ranges = <1 0x00000000 0x42000000 0x02000000>,
<5 0x00000000 0x46000000 0x01000000>;
ethernet@1,1f00000 {
compatible = "smsc,lan9115";
reg = <1 0x01f00000 0x1000>;
interrupts = <0 48 4>;
phy-mode = "mii";
};
serial@5,200000 {
compatible = "ns16550a";
reg = <5 0x00200000 0x20>;
interrupts = <0 49 4>;
clock-frequency = <12288000>;
};
};
|
