| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These update the cpuidle poll state definition to reduce excessive
energy usage related to it, add new CPU ID to the RAPL power capping
driver, update the ACPI system suspend code to handle some special
cases better, extend the PM core's device links code slightly, add new
sysfs attribute for better suspend-to-idle diagnostics and easier
hibernation handling, update power management tools and clean up
cpufreq quite a bit.
Specifics:
- Modify the cpuidle poll state implementation to prevent CPUs from
staying in the loop in there for excessive times (Rafael Wysocki).
- Add Intel Cannon Lake chips support to the RAPL power capping
driver (Joe Konno).
- Add reference counting to the device links handling code in the PM
core (Lukas Wunner).
- Avoid reconfiguring GPEs on suspend-to-idle in the ACPI system
suspend code (Rafael Wysocki).
- Allow devices to be put into deeper low-power states via ACPI if
both _SxD and _SxW are missing (Daniel Drake).
- Reorganize the core ACPI suspend-to-idle wakeup code to avoid a
keyboard wakeup issue on Asus UX331UA (Chris Chiu).
- Prevent the PCMCIA library code from aborting suspend-to-idle due
to noirq suspend failures resulting from incorrect assumptions
(Rafael Wysocki).
- Add coupled cpuidle supprt to the Exynos3250 platform (Marek
Szyprowski).
- Add new sysfs file to make it easier to specify the image storage
location during hibernation (Mario Limonciello).
- Add sysfs files for collecting suspend-to-idle usage and time
statistics for CPU idle states (Rafael Wysocki).
- Update the pm-graph utilities (Todd Brandt).
- Reduce the kernel log noise related to reporting Low-power Idle
constraings by the ACPI system suspend code (Rafael Wysocki).
- Make it easier to distinguish dedicated wakeup IRQs in the
/proc/interrupts output (Tony Lindgren).
- Add the frequency table validation in cpufreq to the core and drop
it from a number of cpufreq drivers (Viresh Kumar).
- Drop "cooling-{min|max}-level" for CPU nodes from a couple of DT
bindings (Viresh Kumar).
- Clean up the CPU online error code path in the cpufreq core (Viresh
Kumar).
- Fix assorted issues in the SCPI, CPPC, mediatek and tegra186
cpufreq drivers (Arnd Bergmann, Chunyu Hu, George Cherian, Viresh
Kumar).
- Drop memory allocation error messages from a few places in cpufreq
and cpuildle drivers (Markus Elfring)"
* tag 'pm-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (56 commits)
ACPI / PM: Fix keyboard wakeup from suspend-to-idle on ASUS UX331UA
cpufreq: CPPC: Use transition_delay_us depending transition_latency
PM / hibernate: Change message when writing to /sys/power/resume
PM / hibernate: Make passing hibernate offsets more friendly
cpuidle: poll_state: Avoid invoking local_clock() too often
PM: cpuidle/suspend: Add s2idle usage and time state attributes
cpuidle: Enable coupled cpuidle support on Exynos3250 platform
cpuidle: poll_state: Add time limit to poll_idle()
cpufreq: tegra186: Don't validate the frequency table twice
cpufreq: speedstep: Don't validate the frequency table twice
cpufreq: sparc: Don't validate the frequency table twice
cpufreq: sh: Don't validate the frequency table twice
cpufreq: sfi: Don't validate the frequency table twice
cpufreq: scpi: Don't validate the frequency table twice
cpufreq: sc520: Don't validate the frequency table twice
cpufreq: s3c24xx: Don't validate the frequency table twice
cpufreq: qoirq: Don't validate the frequency table twice
cpufreq: pxa: Don't validate the frequency table twice
cpufreq: ppc_cbe: Don't validate the frequency table twice
cpufreq: powernow: Don't validate the frequency table twice
...
|
|
* pm-cpuidle:
cpuidle: poll_state: Avoid invoking local_clock() too often
PM: cpuidle/suspend: Add s2idle usage and time state attributes
cpuidle: Enable coupled cpuidle support on Exynos3250 platform
cpuidle: poll_state: Add time limit to poll_idle()
ARM: cpuidle: Drop memory allocation error message from arm_idle_init_cpu()
* pm-tools:
pm-graph: AnalyzeSuspend v5.0
pm-graph: AnalyzeBoot v2.2
pm-graph: config files and installer
|
|
* acpica: (21 commits)
ACPICA: Update version to 20180313
ACPICA: Cleanup/simplify module-level code support
ACPICA: Events: add a return on failure from acpi_hw_register_read
ACPICA: adding SPDX headers
ACPICA: Rename a global for clarity, no functional change
ACPICA: macros: fix ACPI_ERROR_NAMESPACE macro
ACPICA: Change a compile-time option to a runtime option
ACPICA: Remove calling of _STA from acpi_get_object_info()
ACPICA: AML Debug Object: Don't ignore output of zero-length strings
ACPICA: Fix memory leak on unusual memory leak
ACPICA: Events: Dispatch GPEs after enabling for the first time
ACPICA: Events: Add parallel GPE handling support to fix potential redundant _Exx evaluations
ACPICA: Events: Stop unconditionally clearing ACPI IRQs during suspend/resume
ACPICA: acpi: acpica: fix acpi operand cache leak in nseval.c
ACPICA: Update version to 20180209
ACPICA: Add option to disable Package object name resolution errors
ACPICA: Integrate package handling with module-level code
ACPICA: Revert "Fix for implicit result conversion for the To____ functions"
ACPICA: Update for some debug output. No functional change
ACPICA: Update error message, no functional change
...
|
|
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Currently a number of Makefiles break when used with toolchains that
pass extra flags in CC and other cross-compile related variables (such
as --sysroot).
Thus we get this error when we use a toolchain that puts --sysroot in
the CC var:
~/src/linux/tools$ make iio
[snip]
iio_event_monitor.c:18:10: fatal error: unistd.h: No such file or directory
#include <unistd.h>
^~~~~~~~~~
This occurs because we clobber several env vars related to
cross-compiling with lines like this:
CC = $(CROSS_COMPILE)gcc
Although this will point to a valid cross-compiler, we lose any extra
flags that might exist in the CC variable, which can break toolchains
that rely on them (for example, those that use --sysroot).
This easily shows up using a Yocto SDK:
$ . [snip]/sdk/environment-setup-cortexa8hf-neon-poky-linux-gnueabi
$ echo $CC
arm-poky-linux-gnueabi-gcc -march=armv7-a -mfpu=neon -mfloat-abi=hard
-mcpu=cortex-a8
--sysroot=[snip]/sdk/sysroots/cortexa8hf-neon-poky-linux-gnueabi
$ echo $CROSS_COMPILE
arm-poky-linux-gnueabi-
$ echo ${CROSS_COMPILE}gcc
krm-poky-linux-gnueabi-gcc
Although arm-poky-linux-gnueabi-gcc is a cross-compiler, we've lost the
--sysroot and other flags that enable us to find the right libraries to
link against, so we can't find unistd.h and other libraries and headers.
Normally with the --sysroot flag we would find unistd.h in the sdk
directory in the sysroot:
$ find [snip]/sdk/sysroots -path '*/usr/include/unistd.h'
[snip]/sdk/sysroots/cortexa8hf-neon-poky-linux-gnueabi/usr/include/unistd.h
The perf Makefile adds CC = $(CROSS_COMPILE)gcc if and only if CC is not
already set, and it compiles correctly with the above toolchain.
So, generalize the logic that perf uses in the common Makefile and
remove the manual CC = $(CROSS_COMPILE)gcc lines from each Makefile.
Note that this patch does not fix cross-compile for all the tools (some
have other bugs), but it does fix it for all except usb and acpi, which
still have other unrelated issues.
I tested both with and without the patch on native and cross-build and
there appear to be no regressions.
Link: http://lkml.kernel.org/r/20180107214028.23771-1-martin@martingkelly.com
Signed-off-by: Martin Kelly <martin@martingkelly.com>
Acked-by: Mark Brown <broonie@kernel.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Li Zefan <lizefan@huawei.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Pali Rohar <pali.rohar@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Robert Moore <robert.moore@intel.com>
Cc: Lv Zheng <lv.zheng@intel.com>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
- add -cgskip option to reduce callgraph output size
- add -cgfilter option to focus on a list of devices
- add -result option for exporting batch test results
- removed all phoronix hooks, use -result to enable batch testing
- change -usbtopo to -devinfo, now prints all devices
- add -gzip option to read/write logs in gz format
- add -bufsize option to manually control ftrace buffer size
- add -sync option to run filesystem sync prior to test
- add -display option to enable/disable the display prior to test
- add -rs option to enable/disable runtime suspend on all devices for test
- add installed config files to search path
- add kernel error/warning links into the timeline
- fix callgraph trace to better handle interrupts
- include command string and kernel params in timeline output header
Signed-off-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
- add -cgskip option to reduce callgraph output size
- add -cgfilter option to focus on a list of devices
- add -result option for exporting batch test results
- removed all phoronix hooks, use -result to enable batch testing
- changed argument -f to match sleegraph, -f = -callgraph
- use -fstat for function status instead of -f
- add -verbose option to print out timeline stats and kernel options
- include command string and kernel params in timeline output header
Signed-off-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
- name change: analyze_boot.py to bootgraph.py
- name change: analyze_suspend.py to sleepgraph.py
- added config files for easier sleepgraph usage
- added example.cfg which describes all config options
- added cgskip.txt definition for slimmer callgraphs
Signed-off-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
including tool signons.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"The majority of this is an update of the ACPICA kernel code to
upstream revision 20171215 with a cosmetic change and a maintainers
information update on top of it.
The rest is mostly some minor fixes and cleanups in the ACPI drivers
and cleanups to initialization on x86.
Specifics:
- Update the ACPICA kernel code to upstream revision 20171215 including:
* Support for ACPI 6.0A changes in the NFIT table (Bob Moore)
* Local 64-bit divide in string conversions (Bob Moore)
* Fix for a regression in acpi_evaluate_object_type() (Bob Moore)
* Fixes for memory leaks during package object resolution (Bob
Moore)
* Deployment of safe version of strncpy() (Bob Moore)
* Debug and messaging updates (Bob Moore)
* Support for PDTT, SDEV, TPM2 tables in iASL and tools (Bob
Moore)
* Null pointer dereference avoidance in Op and cleanups (Colin Ian
King)
* Fix for memory leak from building prefixed pathname (Erik
Schmauss)
* Coding style fixes, disassembler and compiler updates (Hanjun
Guo, Erik Schmauss)
* Additional PPTT flags from ACPI 6.2 (Jeremy Linton)
* Fix for an off-by-one error in acpi_get_timer_duration()
(Jung-uk Kim)
* Infinite loop detection timeout and utilities cleanups (Lv
Zheng)
* Windows 10 version 1607 and 1703 OSI strings (Mario
Limonciello)
- Update ACPICA information in MAINTAINERS to reflect the current
status of ACPICA maintenance and rename a local variable in one
function to match the corresponding upstream code (Rafael Wysocki)
- Clean up ACPI-related initialization on x86 (Andy Shevchenko)
- Add support for Intel Merrifield to the ACPI GPIO code (Andy
Shevchenko)
- Clean up ACPI PMIC drivers (Andy Shevchenko, Arvind Yadav)
- Fix the ACPI Generic Event Device (GED) driver to free IRQs on
shutdown and clean up the PCI IRQ Link driver (Sinan Kaya)
- Make the GHES code call into the AER driver on all errors and clean
up the ACPI APEI code (Colin Ian King, Tyler Baicar)
- Make the IA64 ACPI NUMA code parse all SRAT entries (Ganapatrao
Kulkarni)
- Add a lid switch blacklist to the ACPI button driver and make it
print extra debug messages on lid events (Hans de Goede)
- Add quirks for Asus GL502VSK and UX305LA to the ACPI battery driver
and clean it up somewhat (Bjørn Mork, Kai-Heng Feng)
- Add device link for CHT SD card dependency on I2C to the ACPI LPSS
(Intel SoCs) driver and make it avoid creating platform device
objects for devices without MMIO resources (Adrian Hunter, Hans de
Goede)
- Fix the ACPI GPE mask kernel command line parameter handling
(Prarit Bhargava)
- Fix the handling of (incorrectly exposed) backlight interfaces
without LCD (Hans de Goede)
- Fix the usage of debugfs_create_*() in the ACPI EC driver (Geert
Uytterhoeven)"
* tag 'acpi-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (62 commits)
ACPI/PCI: pci_link: reduce verbosity when IRQ is enabled
ACPI / LPSS: Do not instiate platform_dev for devs without MMIO resources
ACPI / PMIC: Convert to use builtin_platform_driver() macro
ACPI / x86: boot: Propagate error code in acpi_gsi_to_irq()
ACPICA: Update version to 20171215
ACPICA: trivial style fix, no functional change
ACPICA: Fix a couple memory leaks during package object resolution
ACPICA: Recognize the Windows 10 version 1607 and 1703 OSI strings
ACPICA: DT compiler: prevent error if optional field at the end of table is not present
ACPICA: Rename a global variable, no functional change
ACPICA: Create and deploy safe version of strncpy
ACPICA: Cleanup the global variables and update comments
ACPICA: Debugger: fix slight indentation issue
ACPICA: Fix a regression in the acpi_evaluate_object_type() interface
ACPICA: Update for a few debug output statements
ACPICA: Debug output, no functional change
ACPI: EC: Fix debugfs_create_*() usage
ACPI / video: Default lcd_only to true on Win8-ready and newer machines
ACPI / x86: boot: Don't setup SCI on HW-reduced platforms
ACPI / x86: boot: Use INVALID_ACPI_IRQ instead of 0 for acpi_sci_override_gsi
...
|
|
* acpica: (40 commits)
ACPICA: Update version to 20171215
ACPICA: trivial style fix, no functional change
ACPICA: Fix a couple memory leaks during package object resolution
ACPICA: Recognize the Windows 10 version 1607 and 1703 OSI strings
ACPICA: DT compiler: prevent error if optional field at the end of table is not present
ACPICA: Rename a global variable, no functional change
ACPICA: Create and deploy safe version of strncpy
ACPICA: Cleanup the global variables and update comments
ACPICA: Debugger: fix slight indentation issue
ACPICA: Fix a regression in the acpi_evaluate_object_type() interface
ACPICA: Update for a few debug output statements
ACPICA: Debug output, no functional change
ACPICA: Update information in MAINTAINERS
ACPICA: Rename variable to match upstream
ACPICA: Update version to 20171110
ACPICA: ACPI 6.2: Additional PPTT flags
ACPICA: Update linkage for get mutex name interface
ACPICA: Update mutex error messages, no functional change
ACPICA: Debugger: add "background" command for method execution
ACPICA: Small typo fix, no functional change
...
|
|
The trace buffer memory should be, mostly, freed after
the buffer has been output.
This patch is required before a future patch that will allow
the user to override the default, and specify the trace buffer
memory allocation as a command line option.
Signed-off-by: Doug Smythies <dsmythies@telus.net>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Checkpatch in the kernel now complains about having the FSF address
in comments. Other tools such as rpmlint are now starting to do the
same thing. Remove the FSF address to reduce warnings on multiple tools.
Signed-off-by: Laura Abbott <labbott@redhat.com>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
- add missing module information to the Mediatek cpufreq driver module
(Jesse Chan)
- fix config dependencies for the Loongson cpufreq driver (James Hogan)
- fix two issues related to CPU offline in the cpupower utility
(Abhishek Goel).
* tag 'pm-4.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: mediatek: add missing MODULE_DESCRIPTION/AUTHOR/LICENSE
cpufreq: Add Loongson machine dependencies
cpupower : Fix cpupower working when cpu0 is offline
cpupowerutils: bench - Fix cpu online check
|
|
ACPICA commit 336131640a1574b86240b32eca3150195f9270d6
Common option for all tools.
Link: https://github.com/acpica/acpica/commit/33613164
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux
Pull cpupower utility fixes for 4.15-rc2 from Shuah Khan:
"This update consists of fixes to tool's handling of offline cpus.
The first patch fixes the tool to find information on the cpu it
is running on, instead of always looking for cpu0 and failing if
cpu0 happens to be offline.
The second patch fixes the incorrect check for offline cpu status."
* tag 'linux-cpupower-4.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux:
cpupower : Fix cpupower working when cpu0 is offline
cpupowerutils: bench - Fix cpu online check
|
|
Most places use pwd and rely on $PATH lookup. Moving the remaining
absolute path /bin/pwd users over for consistency.
Also, a reason for doing /bin/pwd -> pwd instead of the other way around
is because I believe build systems should make little assumptions on
host filesystem layout. Case in point, we do this kind of patching
already in NixOS.
Ref. commit 028568d84da3cfca49f5f846eeeef01441d70451
("kbuild: revert $(realpath ...) to $(shell cd ... && /bin/pwd)").
Signed-off-by: Bjørn Forsman <bjorn.forsman@gmail.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
cpuidle_monitor used to assume that cpu0 is always online which is not
a valid assumption on POWER machines. This patch fixes this by getting
the cpu on which the current thread is running, instead of always using
cpu0 for monitoring which may not be online.
Signed-off-by: Abhishek Goel <huntbag@linux.vnet.ibm.com>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
|
|
cpupower_is_cpu_online was incorrectly checking for 0. This patch fixes
this by checking for 1 when the cpu is online.
Signed-off-by: Abhishek Goel <huntbag@linux.vnet.ibm.com>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These update ACPICA to upstream revision 20170831, fix APEI to use the
fixmap instead of ioremap_page_range(), add an operation region driver
for TI PMIC TPS68470, add support for PCC subspace IDs to the ACPI
CPPC driver, fix a few assorted issues and clean up some code.
Specifics:
- Update the ACPICA code to upstream revision 20170831 including
* PDTT table header support (Bob Moore).
* Cleanup and extension of internal string-to-integer conversion
functions (Bob Moore).
* Support for 64-bit hardware accesses (Lv Zheng).
* ACPI PM Timer code adjustment to deal with 64-bit return values
of acpi_hw_read() (Bob Moore).
* Support for deferred table verification in acpiexec (Lv Zheng).
- Fix APEI to use the fixmap instead of ioremap_page_range() which
cannot work correctly the way the code in there attempted to use it
and drop some code that's not necessary any more after that change
(James Morse).
- Clean up the APEI support code and make it use 64-bit timestamps
(Arnd Bergmann, Dongjiu Geng, Jan Beulich).
- Add operation region driver for TI PMIC TPS68470 (Rajmohan Mani).
- Add support for PCC subspace IDs to the ACPI CPPC driver (George
Cherian).
- Fix an ACPI EC driver regression related to the handling of EC
events during the "noirq" phases of system suspend/resume (Lv
Zheng).
- Delay the initialization of the lid state in the ACPI button driver
to fix issues appearing on some systems (Hans de Goede).
- Extend the KIOX000A "device always present" quirk to cover all
affected BIOS versions (Hans de Goede).
- Clean up some code in the ACPI core and drivers (Colin Ian King,
Gustavo Silva)"
* tag 'acpi-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (24 commits)
ACPI: Mark expected switch fall-throughs
ACPI / LPSS: Remove redundant initialization of clk
ACPI / CPPC: Make CPPC ACPI driver aware of PCC subspace IDs
mailbox: PCC: Move the MAX_PCC_SUBSPACES definition to header file
ACPI / sysfs: Make function param_set_trace_method_name() static
ACPI / button: Delay acpi_lid_initialize_state() until first user space open
ACPI / EC: Fix regression related to triggering source of EC event handling
APEI / ERST: use 64-bit timestamps
ACPI / APEI: Remove arch_apei_flush_tlb_one()
arm64: mm: Remove arch_apei_flush_tlb_one()
ACPI / APEI: Remove ghes_ioremap_area
ACPI / APEI: Replace ioremap_page_range() with fixmap
ACPI / APEI: remove the unused dead-code for SEA/NMI notification type
ACPI / x86: Extend KIOX000A quirk to cover all affected BIOS versions
ACPI / APEI: adjust a local variable type in ghes_ioremap_pfn_irq()
ACPICA: Update version to 20170831
ACPICA: Update acpi_get_timer for 64-bit interface to acpi_hw_read
ACPICA: String conversions: Update to add new behaviors
ACPICA: String conversions: Cleanup/format comments. No functional changes
ACPICA: Restructure/cleanup all string-to-integer conversion functions
...
|
|
* pm-devfreq:
PM / devfreq: Define the constant governor name
PM / devfreq: Remove unneeded conditional statement
PM / devfreq: Show the all available frequencies
PM / devfreq: Change return type of devfreq_set_freq_table()
PM / devfreq: Use the available min/max frequency
Revert "PM / devfreq: Add show_one macro to delete the duplicate code"
PM / devfreq: Set min/max_freq when adding the devfreq device
* pm-tools:
tools/power/cpupower: add libcpupower.so.0.0.1 to .gitignore
tools/power/cpupower: Add 64 bit library detection
MAINTAINERS: add maintainer for tools/power/cpupower
cpupower: Fix no-rounding MHz frequency output
|
|
* acpica:
ACPICA: Update version to 20170831
ACPICA: Update acpi_get_timer for 64-bit interface to acpi_hw_read
ACPICA: String conversions: Update to add new behaviors
ACPICA: String conversions: Cleanup/format comments. No functional changes
ACPICA: Restructure/cleanup all string-to-integer conversion functions
ACPICA: Header support for the PDTT ACPI table
ACPICA: acpiexec: Add testability of deferred table verification
ACPICA: Hardware: Enable 64-bit support of hardware accesses
|
|
Commit ac5a181d065d ("cpupower: Add cpuidle parts into library") added
libcpupower.so.0.0.1 which should be hidden from git commands. This
patch changes the ignore to all libcpupower.so.* .
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
|
|
The kernel-tools-lib rpm is installing the library to /usr/lib64, and not
/usr/lib as the cpupower Makefile is doing in the kernel tree. This
resulted in a conflict between the two libraries. After looking at how
other tools installed libraries, and looking at the perf code in
tools/perf it looks like installing to /usr/lib64 for 64-bit arches is the
correct thing to do.
Checks with 'ldd cpupower' on SLES, RHEL, Fedora, and Ubuntu result in
the correct binary AFAICT:
[root@testsystem cpupower]# ldd cpupower | grep cpupower
libcpupower.so.0 => /lib64/libcpupower.so.0 (0x00007f1dab447000)
Commit ac5a181d065d ("cpupower: Add cpuidle parts into library") added a
new cpupower library version. On Fedora, executing the cpupower binary
then resulted in this error
[root@testsystem cpupower]# ./cpupower monitor
./cpupower: symbol lookup error: ./cpupower: undefined symbol:
get_cpu_topology
64-bit libraries should be installed to /usr/lib64, and other libraries
should be installed to /usr/lib.
This code was taken from the perf Makefile.config which supports /usr/lib
and /usr/lib64.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
|
|
'cpupower frequency-info -ln' returns kHz values on systems with MHz range
minimum CPU frequency range. For example, on a 800MHz to 4.20GHz system
the command returns
hardware limits: 800000 MHz - 4.200000 GHz
The code that causes this error can be removed. The next else if clause
will handle the output correctly such that
hardware limits: 800.000 MHz - 4.200000 GHz
is displayed correctly.
[v2]: Remove two lines instead of fixing broken code.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Cc: Thomas Renninger <trenn@suse.com>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Shuah Khan <shuah@kernel.org>
Reviewed-by: Stafford Horne <shorne@gmail.com>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- fix O= building on dash
- remove unused dependency in Makefile
- fix default of a choice in Kconfig
- fix typos and documentation style
- fix command options unrecognized by sparse
* tag 'kbuild-fixes-v4.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: clang: fix build failures with sparse check
kbuild doc: a bundle of fixes on makefiles.txt
Makefile: kselftest: fix grammar typo
kbuild: Fix optimization level choice default
kbuild: drop unused symverfile in Makefile.modpost
kbuild: revert $(realpath ...) to $(shell cd ... && /bin/pwd)
|
|
This reverts commit c91fc8519d87715a3a173475ea3778794c139996.
That change caused a C6 and PC6 residency regression on large idle systems.
Users also complained about new output indicating jitter:
turbostat: cpu6 jitter 3794 9142
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: 4.13+ <stable@vger.kernel.org> # v4.13+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
I thought commit 8e9b46679923 ("kbuild: use $(abspath ...) instead of
$(shell cd ... && /bin/pwd)") was a safe conversion, but it changed
the behavior.
$(abspath ...) / $(realpath ...) does not expand shell special
characters, such as '~'.
Here is a simple Makefile example:
---------------->8----------------
$(info /bin/pwd: $(shell cd ~/; /bin/pwd))
$(info abspath: $(abspath ~/))
$(info realpath: $(realpath ~/))
all:
@:
---------------->8----------------
$ make
/bin/pwd: /home/masahiro
abspath: /home/masahiro/workspace/~
realpath:
This can be a real problem if 'make O=~/foo' is invoked from another
Makefile or primitive shell like dash.
This commit partially reverts 8e9b46679923.
Fixes: 8e9b46679923 ("kbuild: use $(abspath ...) instead of $(shell cd ... && /bin/pwd)")
Reported-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Julien Grall <julien.grall@arm.com>
|
|
ACPICA commit 610046d444ad781cc36673bf1f030abe50cbc61f
Improve adherence to ACPI spec for implicit and explicit conversions
Adds octal support for constants in ASL code
Adds integer overflow errors for constants during ASL compilation
Eliminates most of the existing complex flags parameters
Simplify support for implicit/explicit runtime conversions
Adds one new file, utilities/utstrsuppt.c
Link: https://github.com/acpica/acpica/commit/610046d444ad
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- Use Make-builtin $(abspath ...) helper to get absolute path
- Add W=2 extra warning option to detect unused macros
- Use more KCONFIG_CONFIG instead hard-coded .config
- Fix bugs of tar*-pkg targets
* tag 'kbuild-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: buildtar: do not print successful message if tar returns error
kbuild: buildtar: fix tar error when CONFIG_MODULES is disabled
kbuild: Use KCONFIG_CONFIG in buildtar
Kbuild: enable -Wunused-macros warning for "make W=2"
kbuild: use $(abspath ...) instead of $(shell cd ... && /bin/pwd)
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These include a usual ACPICA code update (this time to upstream
revision 20170728), a fix for a boot crash on some systems with
Thunderbolt devices connected at boot time, a rework of the handling
of PCI bridges when setting up device wakeup, new support for Apple
device properties, support for DMA configurations reported via ACPI on
ARM64, APEI-related updates, ACPI EC driver updates and assorted minor
modifications in several places.
Specifics:
- Update the ACPICA code in the kernel to upstream revision 20170728
including:
* Alias operator handling update (Bob Moore).
* Deferred resolution of reference package elements (Bob Moore).
* Support for the _DMA method in walk resources (Bob Moore).
* Tables handling update and support for deferred table
verification (Lv Zheng).
* Update of SMMU models for IORT (Robin Murphy).
* Compiler and disassembler updates (Alex James, Erik Schmauss,
Ganapatrao Kulkarni, James Morse).
* Tools updates (Erik Schmauss, Lv Zheng).
* Assorted minor fixes and cleanups (Bob Moore, Kees Cook, Lv
Zheng, Shao Ming).
- Rework the initialization of non-wakeup GPEs with method handlers
in order to address a boot crash on some systems with Thunderbolt
devices connected at boot time where we miss an early hotplug event
due to a delay in GPE enabling (Rafael Wysocki).
- Rework the handling of PCI bridges when setting up ACPI-based
device wakeup in order to avoid disabling wakeup for bridges
prematurely (Rafael Wysocki).
- Consolidate Apple DMI checks throughout the tree, add support for
Apple device properties to the device properties framework and use
these properties for the handling of I2C and SPI devices on Apple
systems (Lukas Wunner).
- Add support for _DMA to the ACPI-based device properties lookup
code and make it possible to use the information from there to
configure DMA regions on ARM64 systems (Lorenzo Pieralisi).
- Fix several issues in the APEI code, add support for exporting the
BERT error region over sysfs and update APEI MAINTAINERS entry with
reviewers information (Borislav Petkov, Dongjiu Geng, Loc Ho, Punit
Agrawal, Tony Luck, Yazen Ghannam).
- Fix a potential initialization ordering issue in the ACPI EC driver
and clean it up somewhat (Lv Zheng).
- Update the ACPI SPCR driver to extend the existing XGENE 8250
workaround in it to a new platform (m400) and to work around an
Xgene UART clock issue (Graeme Gregory).
- Add a new utility function to the ACPI core to support using ACPI
OEM ID / OEM Table ID / Revision for system identification in
blacklisting or similar and switch over the existing code already
using this information to this new interface (Toshi Kani).
- Fix an xpower PMIC issue related to GPADC reads that always return
0 without extra pin manipulations (Hans de Goede).
- Add statements to print debug messages in a couple of places in the
ACPI core for easier diagnostics (Rafael Wysocki).
- Clean up the ACPI processor driver slightly (Colin Ian King, Hanjun
Guo).
- Clean up the ACPI x86 boot code somewhat (Andy Shevchenko).
- Add a quirk for Dell OptiPlex 9020M to the ACPI backlight driver
(Alex Hung).
- Assorted fixes, cleanups and updates related to ACPI (Amitoj Kaur
Chawla, Bhumika Goyal, Frank Rowand, Jean Delvare, Punit Agrawal,
Ronald Tschalär, Sumeet Pawnikar)"
* tag 'acpi-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (75 commits)
ACPI / APEI: Suppress message if HEST not present
intel_pstate: convert to use acpi_match_platform_list()
ACPI / blacklist: add acpi_match_platform_list()
ACPI, APEI, EINJ: Subtract any matching Register Region from Trigger resources
ACPI: make device_attribute const
ACPI / sysfs: Extend ACPI sysfs to provide access to boot error region
ACPI: APEI: fix the wrong iteration of generic error status block
ACPI / processor: make function acpi_processor_check_duplicates() static
ACPI / EC: Clean up EC GPE mask flag
ACPI: EC: Fix possible issues related to EC initialization order
ACPI / PM: Add debug statements to acpi_pm_notify_handler()
ACPI: Add debug statements to acpi_global_event_handler()
ACPI / scan: Enable GPEs before scanning the namespace
ACPICA: Make it possible to enable runtime GPEs earlier
ACPICA: Dispatch active GPEs at init time
ACPI: SPCR: work around clock issue on xgene UART
ACPI: SPCR: extend XGENE 8250 workaround to m400
ACPI / LPSS: Don't abort ACPI scan on missing mem resource
mailbox: pcc: Drop uninformative output during boot
ACPI/IORT: Add IORT named component memory address limits
...
|
|
Kbuild conventionally uses $(shell cd ... && /bin/pwd) idiom to get
the absolute path of the directory because GNU Make 3.80, the minimal
supported version at that time, did not support $(abspath ...) or
$(realpath ...).
Commit 37d69ee30808 ("docs: bump minimal GNU Make version to 3.81")
dropped the GNU Make 3.80 support, so we are now allowed to use those
make-builtin helpers.
This conversion will provide better portability without relying on
the pwd command or its location /bin/pwd.
I am intentionally using $(realpath ...) instead $(abspath ...) in
some places. The difference between the two is $(realpath ...)
returns an empty string if the given path does not exist. It is
convenient in places where we need to error-out if the makefile fails
to create an output directory.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Thierry Reding <treding@nvidia.com>
|
|
ACPICA commit 343fc31840d40c06001f3b170ee5bcdfd3c7f3e0
ACPI spec allows to configure different 32-bit/64-bit table addresses for
DSDT and FACS. And for FACS, it's meaningful to dump both of them as they
are used to support different suspend protocols.
While:
1. on Linux, only 1 instance is supported for DSDT/FACS; and
2. on EFI, the code in osl_get_table() is buggy with special table instances,
causing endless file dump for such tables (reported by Shao Ming in link
#2).
This patch adds DSDT/FACS instance support for Linux/EFI acpidump. Fixed by
Lv Zheng.
Link: https://github.com/acpica/acpica/commit/343fc318
Link: https://bugs.acpica.org/show_bug.cgi?id=1407 [#1]
Link: https://github.com/acpica/acpica/issues/285 [#2]
Reported-by: Shao Ming <smbest163@163.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ACPICA commit 01b8f5a2350b9cc329cd8402ac8faec36fc501f5
In order to build ACPICA EFI tools with EDK-II on Windows, 64-bit
multiply/shift supports are also required to be implemented. Otherwise,
MSVC complains:
acpidump.lib(utstrtoul64.obj) : error LNK2001: unresolved external symbol __allmul
acpidump.lib(uthex.obj) : error LNK2001: unresolved external symbol __aullshr
Note:
1. This patch also splits _EDK2_EFI from _GNU_EFI as they might have
different math64 supports.
2. Support of gcc math64 is not included in this patch.
3. Support of EDK2 arch independent math64 is done via linking to base_lib.
This patch fixes this issue. Reported by Shao Ming, fixed by Lv Zheng.
For Linux kernel, this patch is a functional no-op.
Link: https://github.com/acpica/acpica/commit/01b8f5a2
Tested-by: "Shao, Ming" <smbest163@163.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Linux-3.7 added CONFIG_BOOTPARAM_HOTPLUG_CPU0,
allowing systems to offline cpu0.
But when cpu0 is offline, cpupower monitor will not display all
processor and Mperf information:
[root@intel-skylake-dh-03 cpupower]# ./cpupower monitor
WARNING: at least one cpu is offline
|Idle_Stats
CPU | POLL | C1-S | C1E- | C3-S | C6-S | C7s- | C8-S
4| 0.00| 0.00| 0.00| 0.00| 0.90| 0.00| 96.13
1| 0.00| 0.00| 5.49| 0.00| 0.01| 0.00| 92.26
5| 0.00| 0.00| 0.00| 0.00| 0.46| 0.00| 99.50
2| 45.42| 0.00| 0.00| 0.00| 22.94| 0.00| 28.84
6| 0.00| 37.54| 0.00| 0.00| 0.00| 0.00| 0.00
3| 0.00| 0.00| 0.00| 0.00| 0.30| 0.00| 91.99
7| 0.00| 0.00| 0.00| 0.00| 4.70| 0.00| 0.70
This patch replaces the hard-coded use of cpu0 in cpupower with the
current cpu, allowing it to run without a cpu0.
After the patch is applied,
[root@intel-skylake-dh-03 cpupower]# ./cpupower monitor
WARNING: at least one cpu is offline
|Nehalem || Mperf || Idle_Stats
CPU | C3 | C6 | PC3 | PC6 || C0 | Cx | Freq || POLL | C1-S | C1E- | C3-S | C6-S | C7s- | C8-S
4| 0.01| 1.27| 0.00| 0.00|| 0.04| 99.96| 3957|| 0.00| 0.00| 0.00| 0.00| 1.43| 0.00| 98.52
1| 0.00| 98.82| 0.00| 0.00|| 0.05| 99.95| 3361|| 0.00| 0.00| 0.01| 0.00| 0.03| 0.00| 99.88
5| 0.00| 98.82| 0.00| 0.00|| 0.09| 99.91| 3917|| 0.00| 0.00| 0.00| 0.00| 99.38| 0.00| 0.50
2| 0.33| 0.00| 0.00| 0.00|| 0.00|100.00| 3890|| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00|100.00
6| 0.33| 0.00| 0.00| 0.00|| 0.01| 99.99| 3903|| 0.00| 0.00| 0.00| 0.00| 0.00| 0.00| 99.99
3| 0.01| 0.71| 0.00| 0.00|| 0.06| 99.94| 3678|| 0.00| 0.00| 0.00| 0.00| 0.80| 0.00| 99.13
7| 0.01| 0.71| 0.00| 0.00|| 0.03| 99.97| 3538|| 0.00| 0.69| 11.70| 0.00| 0.00| 0.00| 87.57
There are some minor cleanups included in this patch.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Thomas Renninger <trenn@suse.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
update help text and man pages for both tools
- added more examples and separated them by category
Makefile upgrades
- uninstall: remove errors from uninstall if tool not found
- install: perform uninstall before install
Signed-off-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
- changed output from single html file to dir with html/dmesg/ftrace
- add sysinfo to logs and timeline
- add -sysinfo command, displays dmidecode values and cpu/mem info
- set trace buffer size to lesser of memtotal/2 or 2GB when using callgraph
- extended timeline to the last init call in user space
separated timeline into two phases, kernel mode & user mode
- add kernel version check for ftrace usage, 4.10 minimum
- change -filter argument to -func
- add strict protections on -func usage with full symbol checks
now only works for statically linked functions
cmd -flistall now ignores all loadable module functions
- add -cgfilter argument for reducing timeline size by removing callgraphs
- crontab usage: preserve existing @reboot lines in user crontab
- fedora support added: uses grub2 loader, handles fedora crontab
- stop using "which" to find binaries, search pre-defined path list
- moved most output processing to analyze_suspend library
Signed-off-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
- changed -rtcwake parameter to be on & 15 sec by default,
to disable rtcwake use: "-rtcwake off"
- changed behavior of -o: renames HTML file on rerun, subdir on new run
- changed execution_misalignment error to missing_function_name
- add sysinfo to logs and timeline via a custom dmidecode call
it supplants dmidecode tool when used as a library call
- add -sysinfo command, displays dmidecode values and cpu/mem info
- set trace buffer size to lesser of memtotal/2 or 2GB when using callgraph
- add support for /sys/power/mem_sleep. if mem_sleep found:
mem-shallow=standby, mem-s2idle=freeze, mem-deep=mem
- remove redundant javascript
- cosmetic changes to HTML layout
Signed-off-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These mostly update the ACPICA code in the kernel to upstream revision
20170531 which covers all of the new material from ACPI 6.2, including
new tables (WSMT, HMAT, PPTT), new subtables and definition changes
for some existing tables (BGRT, HEST, SRAT, TPM2, PCCT), new resource
descriptor macros for pin control, support for new predefined methods
(_LSI, _LSR, _LSW, _HMA), fixes and cleanups.
On top of that, an additional ACPICA change from Kees (which also is
upstream already) switches all of the definitions of function pointer
structures in ACPICA to use designated initializers so as to make the
structure layout randomization GCC plugin work with it.
The rest is a few fixes and cleanups in the EC driver, an xpower PMIC
driver update, a new backlight blacklist entry, and update of the
tables configfs interface and a messages formatting cleanup.
Specifics:
- Update the ACPICA code in the kernel to upstream revision revision
20170531 (which covers all of the new material from ACPI 6.2)
including:
* Support for the PinFunction(), PinConfig(), PinGroup(),
PinGroupFunction(), and PinGroupConfig() resource descriptors
(Mika Westerberg).
* Support for new subtables in HEST and SRAT, new notify value for
HEST, header support for TPM2 table changes, and BGRT Status
field update (Bob Moore).
* Support for new PCCT subtables (David Box).
* Support for _LSI, _LSR, _LSW, and _HMA as predefined methods
(Erik Schmauss).
* Support for the new WSMT, HMAT, and PPTT tables (Lv Zheng).
* New UUID values for Processor Properties (Bob Moore).
* New notify values for memory attributes and graceful shutdown
(Bob Moore).
* Fix related to the PCAT_COMPAT MADT flag (Janosch Hildebrand).
* Resource to AML conversion fix for resources containing GPIOs
(Mika Westerberg).
* Disassembler-related updates (Bob Moore, David Box, Erik
Schmauss).
* Assorted fixes and cleanups (Bob Moore, Erik Schmauss, Lv Zheng,
Cao Jin).
- Modify ACPICA to always use designated initializers for function
pointer structures to make the structure layout randomization GCC
plugin work with it (Kees Cook).
- Update the tables configfs interface to unload SSDTs on configfs
entry removal (Jan Kiszka).
- Add support for the GPI1 regulator to the xpower PMIC Operation
Region handler (Hans de Goede).
- Fix ACPI EC issues related to conflicting EC definitions in the
ECDT and in the ACPI namespace (Lv Zheng, Carlo Caione, Chris
Chiu).
- Fix an interrupt storm issue in the EC driver and make its debug
output work with dynamic debug as expected (Lv Zheng).
- Add ACPI backlight quirk for Dell Precision 7510 (Shih-Yuan Lee).
- Fix whitespace in pr_fmt() to align log entries properly in some
places in the ACPI subsystem (Vincent Legoll)"
* tag 'acpi-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (63 commits)
ACPI / EC: Add quirk for GL720VMK
ACPI / EC: Fix media keys not working problem on some Asus laptops
ACPI / EC: Add support to skip boot stage DSDT probe
ACPI / EC: Enhance boot EC sanity check
ACPI / video: Add quirks for the Dell Precision 7510
ACPI: EC: Fix EC command visibility for dynamic debug
ACPI: EC: Fix an EC event IRQ storming issue
ACPICA: Use designated initializers
ACPICA: Update version to 20170531
ACPICA: Update a couple of debug output messages
ACPICA: acpiexec: enhance local signal handler
ACPICA: Simplify output for the ACPI Debug Object
ACPICA: Unix application OSL: Correctly handle control-c (EINTR)
ACPICA: Improvements for debug output only
ACPICA: Disassembler: allow conflicting external declarations to be emitted.
ACPICA: Disassembler: add external op to namespace on first pass
ACPICA: Disassembler: prevent external op's from opening a new scope
ACPICA: Changed Gbl_disasm_flag to acpi_gbl_disasm_flag
ACPICA: Changing External to a named object
ACPICA: Update two error messages to emit control method name
...
|
|
ACPICA commit dfbb87c3a96cfd007375f34a96e6f4a8ee477f97
Handle EINTR from a sem_wait operation. Ignore a control-c.
Link: https://github.com/acpica/acpica/commit/dfbb87c3
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add support for new AMD family 0x17
- Add bit field changes to the msr_pstate structure
- Add the new formula for the calculation of cof
- Changed method to access to CpbDis
Signed-off-by: Sherry Hurwitz <sherry.hurwitz@amd.com>
Acked-by: Thomas Renninger <trenn@suse.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Save return value from amd_pci_get_num_boost_states
and remove redundant setting of *support
Signed-off-by: Sherry Hurwitz <sherry.hurwitz@amd.com>
Reviewed-by: Thomas Renninger <trenn@suse.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
|
|
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
otherwise, turbostat bails on on AMD Opteron boxes:
turbostat: cpu26: msr offset 0x1a0 read failed: Input/output error
Reported-by: Kamil Kolakowski <kkolakow@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Turbostat has the capability to set its own affinity to
each CPU so that its MSR accesses are on the local CPU.
However, using the in-kernel cross-call in the msr driver
tends to be less invasive, so do that -- by-default.
'-m' remains to get the old behaviour.
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
The --debug option now pre-pends each row with
the number of micro-seconds [usec] to collect
the finishing snapshot for that row.
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Skylake has some new counters, and they were erroneously
exempt from --show and --hide
eg.
turbostat --quiet --show CPU
CPU Totl%C0 Any%C0 GFX%C0 CPUGFX%
- 116.73 90.56 85.69 79.00
0 117.78 91.38 86.47 79.71
2
1
3
is now
CPU
-
0
2
1
3
Signed-off-by: Len Brown <len.brown@intel.com>
|
