| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
AMD P-State kernel module is using the fine grain frequency instead of
acpi hardware pstate. So add a function to print performance and
frequency values.
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
The print_speed can be as a common function, and expose it into misc
helper header. Then it can be used on other helper files as well.
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
The legacy ACPI hardware P-States function has 3 P-States on ACPI table,
the CPU frequency only can be switched between the 3 P-States. While the
processor supports the boost state, it will have another boost state
that the frequency can be higher than P0 state, and the state can be
decoded by the function of decode_pstates() and read by
amd_pci_get_num_boost_states().
However, the new AMD P-State function is different than legacy ACPI
hardware P-State on AMD processors. That has a finer grain frequency
range between the highest and lowest frequency. And boost frequency is
actually the frequency which is mapped on highest performance ratio. The
similar previous P0 frequency is mapped on nominal performance ratio.
If the highest performance on the processor is higher than nominal
performance, then we think the current processor supports the boost
state. And it uses amd_pstate_boost_init() to initialize boost for AMD
P-State function.
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
Introduce the marco definitions and access helper function for
AMD P-State sysfs interfaces such as each performance goals and frequency
levels in amd helper file. They will be used to read the sysfs attribute
from AMD P-State cpufreq driver for cpupower utilities.
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
Kernel ACPI subsytem introduced the sysfs attributes for acpi cppc
library in below path:
/sys/devices/system/cpu/cpuX/acpi_cppc/
And these attributes will be used for AMD P-State driver to provide some
performance and frequency values.
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
Expose the helper into cpufreq header, then cpufreq driver can use this
function to get the sysfs value if it has any specific sysfs interfaces.
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
If kernel starts the AMD P-State module, the cpupower will initial the
capability flag as CPUPOWER_CAP_AMD_PSTATE. And once AMD P-State
capability is set, it won't need to set legacy ACPI relative
capabilities anymore.
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
The processor with AMD P-State function also supports legacy ACPI
hardware P-States feature as well. Once driver sets AMD P-State eanbled,
the processor will respond the finer grain AMD P-State feature instead of
legacy ACPI P-States. So it introduces the cpupower_amd_pstate_enabled()
to check whether the current kernel enables AMD P-State or AMD CPUFreq
module.
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
Add AMD P-State capability flag in cpupower to indicate AMD new P-State
kernel module support on Ryzen processors.
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
This version allows out of band SST support, where some remote agent
changes SST profiles via some Board Management Controller.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
|
|
Read HFI (Hardware Feedback Interface) events to process config level
changes in oob mode. When HFI is supported there is no need for polling
to check config level change.
Subscribe to Linux thermal netlink messages and process message:
THERMAL_GENL_EVENT_CPU_CAPABILITY_CHANGE.
This message contains cpu number, performance and energy efficiency.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
|
|
It is possible that some out of band agent changed config level. In this
case CPUs need to be online/offline to support this config change. Add
a command line option --oob, so that this tool can run as daemon and poll
for config level change and take action. The poll interval is configurable
in seconds using config option --poll-interval.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
|
|
$(or ...) is available since GNU Make 3.81, and useful to shorten the
code in some places.
Covert as follows:
$(if A,A,B) --> $(or A,B)
This patch also converts:
$(if A, A, B) --> $(or A, B)
Strictly speaking, the latter is not an equivalent conversion because
GNU Make keeps spaces after commas; if A is not empty, $(if A, A, B)
expands to " A", while $(or A, B) expands to "A".
Anyway, preceding spaces are not significant in the code hunks I touched.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Nicolas Schier <nicolas@fjasle.eu>
|
|
Renamed the to-do file to 'TODO' instead of 'ToDo' to
comply with the naming standard.
Signed-off-by: ozkanonur <onurozkan.dev@gmail.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
The tools name was wrong in the SYNTAX section of the manpage it should
read "idle-set" instead of "idle-info".
Signed-off-by: Andreas Rammhold <andreas@rammhold.de>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"The most significant item here is the Platform Firmware Runtime Update
and Telemetry (PFRUT) support designed to allow certain pieces of the
platform firmware to be updated on the fly, among other things.
Also important is the e820 handling change on x86 that should work
around PCI BAR allocation issues on some systems shipping since 2019.
The rest is just a handful of assorted fixes and cleanups on top of
the ACPI material merged previously.
Specifics:
- Add support for the the Platform Firmware Runtime Update and
Telemetry (PFRUT) interface based on ACPI to allow certain pieces
of the platform firmware to be updated without restarting the
system and to provide a mechanism for collecting platform firmware
telemetry data (Chen Yu, Dan Carpenter, Yang Yingliang).
- Ignore E820 reservations covering PCI host bridge windows on
sufficiently recent x86 systems to avoid issues with allocating PCI
BARs on systems where the E820 reservations cover the entire PCI
host bridge memory window returned by the _CRS object in the
system's ACPI tables (Hans de Goede).
- Fix and clean up acpi_scan_init() (Rafael Wysocki).
- Add more sanity checking to ACPI SPCR tables parsing (Mark
Langsdorf).
- Fix up ACPI APD (AMD Soc) driver initialization (Jiasheng Jiang).
- Drop unnecessary "static" from the ACPI PCC address space handling
driver added recently (kernel test robot)"
* tag 'acpi-5.17-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: PCC: pcc_ctx can be static
ACPI: scan: Rename label in acpi_scan_init()
ACPI: scan: Simplify initialization of power and sleep buttons
ACPI: scan: Change acpi_scan_init() return value type to void
ACPI: SPCR: check if table->serial_port.access_width is too wide
ACPI: APD: Check for NULL pointer after calling devm_ioremap()
x86/PCI: Ignore E820 reservations for bridge windows on newer systems
ACPI: pfr_telemetry: Fix info leak in pfrt_log_ioctl()
ACPI: pfr_update: Fix return value check in pfru_write()
ACPI: tools: Introduce utility for firmware updates/telemetry
ACPI: Introduce Platform Firmware Runtime Telemetry driver
ACPI: Introduce Platform Firmware Runtime Update device driver
efi: Introduce EFI_FIRMWARE_MANAGEMENT_CAPSULE_HEADER and corresponding structures
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver updates from Hans de Goede:
"Highlights:
New drivers:
- asus-tf103c-dock
- intel_crystal_cove_charger
- lenovo-yogabook-wmi
- simatic-ipc platform-code + led driver + watchdog driver
- x86-android-tablets (kernel module to workaround DSDT bugs on
these)
amd-pmc:
- bug-fixes
- smar trace buffer support
asus-wmi:
- support for custom fan curves
int3472 (camera info ACPI object for Intel IPU3/SkyCam cameras):
- ACPI core + int3472 changes to delay enumeration of camera sensor
I2C clients until the PMIC for the sensor has been fully probed
- Add support for board data (DSDT info is incomplete) for setting up
the tps68470 PMIC used on some boards with these cameras
- Add board data for the Microsoft Surface Go (original, v2 and v3)
thinkpad_acpi:
- various cleanups
- support for forced battery discharging (for battery calibration)
- support to inhibit battery charging
- this includes power_supply core changes to add new APIs for this
think_lmi:
- enhanced BIOS password support
various other small fixes and hardware-id additions"
* tag 'platform-drivers-x86-v5.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (78 commits)
power: supply: Provide stubs for charge_behaviour helpers
platform/x86: x86-android-tablets: Fix GPIO lookup leak on error-exit
platform/x86: int3472: Add board data for Surface Go 3
platform/x86: Add Asus TF103C dock driver
platform/x86: x86-android-tablets: Add TM800A550L data
platform/x86: x86-android-tablets: Add Asus MeMO Pad 7 ME176C data
platform/x86: x86-android-tablets: Add Asus TF103C data
platform/x86: x86-android-tablets: Add support for preloading modules
platform/x86: x86-android-tablets: Add support for registering GPIO lookup tables
platform/x86: x86-android-tablets: Add support for instantiating serdevs
platform/x86: x86-android-tablets: Add support for instantiating platform-devs
platform/x86: x86-android-tablets: Add support for PMIC interrupts
platform/x86: x86-android-tablets: Don't return -EPROBE_DEFER from a non probe() function
platform/x86: touchscreen_dmi: Remove the Glavey TM800A550L entry
platform/x86: touchscreen_dmi: Enable pen support on the Chuwi Hi10 Plus and Pro
platform/x86: touchscreen_dmi: Correct min/max values for Chuwi Hi10 Pro (CWI529) tablet
platform/x86: Add intel_crystal_cove_charger driver
power: supply: fix charge_behaviour attribute initialization
platform/x86: intel-uncore-frequency: use default_groups in kobj_type
x86/platform/uv: use default_groups in kobj_type
...
|
|
Introduce a user space tool to make use of the interface exposed by
Platform Firmware Runtime Update and Telemetry drivers.
It can be used for firmware code injection, driver updates and
to retrieve platform firmware telemetry data.
Tested-by: Hongyu Ning <hongyu.ning@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This release adds following change:
- Update max performance when BIOS disabled turbo
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
When BIOS disables turbo, the cpuinfo_max_freq will also be same as the
power up base frequency. When SST-PP causes increase in base frequency
the performance will be still limited to the old base frequency as the
cpuinfo_max_freq will not be updated.
In this case we need to update scaling_max frequency to the new
base_frequency. This will result in setting updated max performance
limit in the Pstate driver. So performance will not be limited to the
old base frequency.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Compiling the ACPI tools when output directory parameter is specified,
but the output directory is not present, triggers the following error:
make O=/data/test/tmp/ -C tools/power/acpi/
make: Entering directory '/data/src/kernel/linux/tools/power/acpi'
DESCEND tools/acpidbg
make[1]: Entering directory '/data/src/kernel/linux/tools/power/acpi/tools/acpidbg'
MKDIR include
CP include
CC tools/acpidbg/acpidbg.o
Assembler messages:
Fatal error: can't create /data/test/tmp/tools/power/acpi/tools/acpidbg/acpidbg.o: No such file or directory
make[1]: *** [../../Makefile.rules:24: /data/test/tmp/tools/power/acpi/tools/acpidbg/acpidbg.o] Error 1
make[1]: Leaving directory '/data/src/kernel/linux/tools/power/acpi/tools/acpidbg'
make: *** [Makefile:18: acpidbg] Error 2
make: Leaving directory '/data/src/kernel/linux/tools/power/acpi'
which occurs because the output directory has not been created yet.
Fix this issue by creating the output directory before compiling.
Reported-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[ rjw: New subject, changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This release adds following change:
- Fix reporting of memory frequency
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The uncore memory frequency value from the mailbox command
CONFIG_TDP_GET_MEM_FREQ needs to be scaled based on the platform for
display. There is no single constant multiplier.
This change introduces CPU model specific memory frequency multiplier.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pull turbostat updates from Len Brown:
"Bug fixes and a smattering of features"
* 'turbostat' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (21 commits)
tools/power turbostat: version 2021.05.04
tools/power turbostat: Support "turbostat --hide idle"
tools/power turbostat: elevate priority of interval mode
tools/power turbostat: formatting
tools/power turbostat: rename tcc variables
tools/power turbostat: add TCC Offset support
tools/power turbostat: save original CPU model
tools/power turbostat: Fix Core C6 residency on Atom CPUs
tools/power turbostat: Print the C-state Pre-wake settings
tools/power turbostat: Enable tsc_tweak for Elkhart Lake and Jasper Lake
tools/power turbostat: unmark non-kernel-doc comment
tools/power/turbostat: Remove Package C6 Retention on Ice Lake Server
tools/power turbostat: Fix offset overflow issue in index converting
tools/power/turbostat: Fix turbostat for AMD Zen CPUs
tools/power turbostat: update version number
tools/power turbostat: Fix DRAM Energy Unit on SKX
Revert "tools/power turbostat: adjust for temperature offset"
tools/power turbostat: Support Ice Lake D
tools/power turbostat: Support Alder Lake Mobile
tools/power turbostat: print microcode patch level
...
|
|
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
As idle, in particular, can have many columns on some machines...
Make it easy to ignore them all at once.
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
This makes interval mode less likely to see delayed
results on a heavily loaded system.
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Spring is here...
run a long overdue Lendent on turbostat.c
no functional change
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
There are two TCC activation temeprature.
One is the default TCC activation temperature, also known as TJ_MAX.
Another one is the effective TCC activation temperature, which is the
subtraction of default TCC activation temperature and TCC offset.
The name of variable tcc_activation_temp might be misleading here.
Thus rename tcc_activation_temp to tj_max, and use tcc_default and
tcc_offset to calculate the effective TCC activation temperature.
No functional change in this patch.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
The length of TCC Offset bits varies on different platforms.
Decode TCC Offset bits only for the platforms that we have verified.
For the others, only show default TCC activation temperature.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
CPU model may get changed in intel_model_duplicates() for code reuse.
But there are still some cases we need the original CPU model to handle
minor differences between generations.
Thus save the original CPU model.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
For Atom CPUs that have core cstate deeper than C6,
MSR_CORE_C6_RESIDENCY actually returns the residency for both CC6 and
deeper Core cstates.
Thus, the real Core C6 residency should be the subtraction of
MSR_CORE_C6_RESIDENCY return value and MSR_CORE_C6_RESIDENCY return value.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
C-state pre-wake setting[1] is an optimization for some Intel CPUs to
be woken up from deep C-states in order to reduce latency. According to
the spec, the BIT30 is the C-state Pre-wake Disable. Expose this setting
accordingly.
Sample output from turbostat:
...
cpu51: MSR_IA32_POWER_CTL: 0x1a00a40059 (C1E auto-promotion: DISabled)
C-state Pre-wake: ENabled
cpu51: MSR_TURBO_RATIO_LIMIT: 0x2021212121212224
...
[1] https://intel.github.io/wult/#c-state-pre-wake
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
It was found that on Elkhart Lake the TSC frequency is driven by
a separate crystal-clock domain, which is different from the
BCLK domain which includes mperf. This has result in small different
speed thus inconsistence between TSC and the mperf, which caused the
Busy% to be higher than 100%. On this platform it seems that the mperf
runs faster than tsc when the CPU is 100% utilized:
delta tsc(18815473183) < delta mperf(18958403680) for 10 seconds.
To align TSC with mperf, leverage the tsc_tweak mechanism introduced for
cores newer than Skylake, so that TSC and mperf would be calculated in
the same domain.
Reported-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Do not mark a comment as kernel-doc notation when it is not
meant to be in kernel-doc notation.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Currently the turbostat treats ICX the same way as SKX and shares the
code among them. But one difference is that ICX does not support Package
C6 Retention, unlike SKX and CLX.
So this patch:
1. Splitting SKX and ICX in turbostat.
2. Removing Package C6 Rentention for ICX.
And after this split, it would be easier to cutomize Ice Lake Server
in turbostat in the future.
Suggested-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Reviewed-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Tested-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
The idx_to_offset() function returns type int (32-bit signed), but
MSR_PKG_ENERGY_STAT is u32 and would be interpreted as a negative number.
The end result is that it hits the if (offset < 0) check in update_msr_sum()
which prevents the timer callback from updating the stat in the background when
long durations are used. The similar issue exists in offset_to_idx() and
update_msr_sum(). Fix this issue by converting the 'int' to 'off_t' accordingly.
Fixes: 9972d5d84d76 ("tools/power turbostat: Enable accumulate RAPL display")
Signed-off-by: Calvin Walton <calvin.walton@kepstin.ca>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
It was reported that on Zen+ system turbostat started exiting,
which was tracked down to the MSR_PKG_ENERGY_STAT read failing because
offset_to_idx wasn't returning a non-negative index.
This patch combined the modification from Bingsong Si and
Bas Nieuwenhuizen and addd the MSR to the index system as alternative for
MSR_PKG_ENERGY_STATUS.
Fixes: 9972d5d84d76 ("tools/power turbostat: Enable accumulate RAPL display")
Reported-by: youling257 <youling257@gmail.com>
Tested-by: youling257 <youling257@gmail.com>
Tested-by: Kurt Garloff <kurt@garloff.de>
Tested-by: Bingsong Si <owen.si@ucloud.cn>
Tested-by: Artem S. Tashkinov <aros@gmx.com>
Co-developed-by: Bingsong Si <owen.si@ucloud.cn>
Co-developed-by: Terry Bowman <terry.bowman@amd.com>
Signed-off-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Reviewed-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
|
|
SKX uses fixed DRAM Energy Unit, just like HSX and BDX.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
This reverts commit 6ff7cb371c4bea3dba03a56d774da925e78a5087.
Apparently the TCC offset should not be used to adjust what temperature
we show the user after all.
(on most systems, TCC offset is 0, FWIW)
Fixes: 6ff7cb371c4b
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Ice Lake D is low-end server version of Ice Lake X, reuse
the code accordingly.
Tested-by: Wendy Wang <wendy.wang@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Share the code between Alder Lake Mobile and Alder Lake Desktop.
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
(also available via "grep microcode /proc/cpuinfo")
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Use linux-perf to access the hardware instructions-retired counter.
This is necessary because the counter is not enabled by default,
and also the counter is prone to roll-over -- both of which
perf manages.
It is not necessary to use perf for the cycle counter,
because turbostat already needs to collect delta-aperf
to calcuate frequency.
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These add some new hardware support (for example, IceLake-D idle
states in intel_idle), fix some issues (for example, the handling of
negative "sleep length" values in cpuidle governors), add new
functionality to the existing drivers (for example, scale-invariance
support in the ACPI CPPC cpufreq driver) and clean up code all over.
Specifics:
- Add idle states table for IceLake-D to the intel_idle driver and
update IceLake-X C6 data in it (Artem Bityutskiy).
- Fix the C7 idle state on Tegra114 in the tegra cpuidle driver and
drop the unused do_idle() firmware call from it (Dmitry Osipenko).
- Fix cpuidle-qcom-spm Kconfig entry (He Ying).
- Fix handling of possible negative tick_nohz_get_next_hrtimer()
return values of in cpuidle governors (Rafael Wysocki).
- Add support for frequency-invariance to the ACPI CPPC cpufreq
driver and update the frequency-invariance engine (FIE) to use it
as needed (Viresh Kumar).
- Simplify the default delay_us setting in the ACPI CPPC cpufreq
driver (Tom Saeger).
- Clean up frequency-related computations in the intel_pstate cpufreq
driver (Rafael Wysocki).
- Fix TBG parent setting for load levels in the armada-37xx cpufreq
driver and drop the CPU PM clock .set_parent method for armada-37xx
(Marek Behún).
- Fix multiple issues in the armada-37xx cpufreq driver (Pali Rohár).
- Fix handling of dev_pm_opp_of_cpumask_add_table() return values in
cpufreq-dt to take the -EPROBE_DEFER one into acconut as
appropriate (Quanyang Wang).
- Fix format string in ia64-acpi-cpufreq (Sergei Trofimovich).
- Drop the unused for_each_policy() macro from cpufreq (Shaokun
Zhang).
- Simplify computations in the schedutil cpufreq governor to avoid
unnecessary overhead (Yue Hu).
- Fix typos in the s5pv210 cpufreq driver (Bhaskar Chowdhury).
- Fix cpufreq documentation links in Kconfig (Alexander Monakov).
- Fix PCI device power state handling in pci_enable_device_flags() to
avoid issuse in some cases when the device depends on an ACPI power
resource (Rafael Wysocki).
- Add missing documentation of pm_runtime_resume_and_get() (Alan
Stern).
- Add missing static inline stub for pm_runtime_has_no_callbacks() to
pm_runtime.h and drop the unused try_to_freeze_nowarn() definition
(YueHaibing).
- Drop duplicate struct device declaration from pm.h and fix a
structure type declaration in intel_rapl.h (Wan Jiabing).
- Use dev_set_name() instead of an open-coded equivalent of it in the
wakeup sources code and drop a redundant local variable
initialization from it (Andy Shevchenko, Colin Ian King).
- Use crc32 instead of md5 for e820 memory map integrity check during
resume from hibernation on x86 (Chris von Recklinghausen).
- Fix typos in comments in the system-wide and hibernation support
code (Lu Jialin).
- Modify the generic power domains (genpd) code to avoid resuming
devices in the "prepare" phase of system-wide suspend and
hibernation (Ulf Hansson).
- Add Hygon Fam18h RAPL support to the intel_rapl power capping
driver (Pu Wen).
- Add MAINTAINERS entry for the dynamic thermal power management
(DTPM) code (Daniel Lezcano).
- Add devm variants of operating performance points (OPP) API
functions and switch over some users of the OPP framework to the
new resource-managed API (Yangtao Li and Dmitry Osipenko).
- Update devfreq core:
* Register devfreq devices as cooling devices on demand (Daniel
Lezcano).
* Add missing unlock opeation in devfreq_add_device() (Lukasz
Luba).
* Use the next frequency as resume_freq instead of the previous
frequency when using the opp-suspend property (Dong Aisheng).
* Check get_dev_status in devfreq_update_stats() (Dong Aisheng).
* Fix set_freq path for the userspace governor in Kconfig (Dong
Aisheng).
* Remove invalid description of get_target_freq() (Dong Aisheng).
- Update devfreq drivers:
* imx8m-ddrc: Remove imx8m_ddrc_get_dev_status() and unneeded
of_match_ptr() (Dong Aisheng, Fabio Estevam).
* rk3399_dmc: dt-bindings: Add rockchip,pmu phandle and drop
references to undefined symbols (Enric Balletbo i Serra, Gaël
PORTAY).
* rk3399_dmc: Use dev_err_probe() to simplify the code (Krzysztof
Kozlowski).
* imx-bus: Remove unneeded of_match_ptr() (Fabio Estevam).
- Fix kernel-doc warnings in three places (Pierre-Louis Bossart).
- Fix typo in the pm-graph utility code (Ricardo Ribalda)"
* tag 'pm-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (74 commits)
PM: wakeup: remove redundant assignment to variable retval
PM: hibernate: x86: Use crc32 instead of md5 for hibernation e820 integrity check
cpufreq: Kconfig: fix documentation links
PM: wakeup: use dev_set_name() directly
PM: runtime: Add documentation for pm_runtime_resume_and_get()
cpufreq: intel_pstate: Simplify intel_pstate_update_perf_limits()
cpufreq: armada-37xx: Fix module unloading
cpufreq: armada-37xx: Remove cur_frequency variable
cpufreq: armada-37xx: Fix determining base CPU frequency
cpufreq: armada-37xx: Fix driver cleanup when registration failed
clk: mvebu: armada-37xx-periph: Fix workaround for switching from L1 to L0
clk: mvebu: armada-37xx-periph: Fix switching CPU freq from 250 Mhz to 1 GHz
cpufreq: armada-37xx: Fix the AVS value for load L1
clk: mvebu: armada-37xx-periph: remove .set_parent method for CPU PM clock
cpufreq: armada-37xx: Fix setting TBG parent for load levels
cpuidle: Fix ARM_QCOM_SPM_CPUIDLE configuration
cpuidle: tegra: Remove do_idle firmware call
cpuidle: tegra: Fix C7 idling state on Tegra114
PM: sleep: fix typos in comments
cpufreq: Remove unused for_each_policy macro
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These update the ACPICA code in the kernel to the most recent upstream
revision including (but not limited to) new material introduced in the
6.4 version of the spec, update message printing in the ACPI-related
code, address a few issues and clean up code in a number of places.
Specifics:
- Update ACPICA code in the kernel to upstream revision 20210331
including the following changes:
* Add parsing for IVRS IVHD 40h and device entry F0h (Alexander
Monakov).
* Add new CEDT table for CXL 2.0 and iASL support for it (Ben
Widawsky, Bob Moore).
* NFIT: add Location Cookie field (Bob Moore).
* HMAT: add new fields/flags (Bob Moore).
* Add new flags in SRAT (Bob Moore).
* PMTT: add new fields/structures (Bob Moore).
* Add CSI2Bus resource template (Bob Moore).
* iASL: Decode subtable type field for VIOT (Bob Moore).
* Fix various typos and spelling mistakes (Colin Ian King).
* Add new predefined objects _BPC, _BPS, and _BPT (Erik Kaneda).
* Add USB4 capabilities UUID (Erik Kaneda).
* Add CXL ACPI device ID and _CBR object (Erik Kaneda).
* MADT: add Multiprocessor Wakeup Structure (Erik Kaneda).
* PCCT: add support for subtable type 5 (Erik Kaneda).
* PPTT: add new version of subtable type 1 (Erik Kaneda).
* Add SDEV secure access components (Erik Kaneda).
* Add support for PHAT table (Erik Kaneda).
* iASL: Add definitions for the VIOT table (Jean-Philippe
Brucker).
* acpisrc: Add missing conversion for VIOT support (Jean-Philippe
Brucker).
* IORT: Updates for revision E.b (Shameer Kolothum).
- Rearrange message printing in ACPI-related code to avoid using the
ACPICA's internal message printing macros outside ACPICA and do
some related code cleanups (Rafael Wysocki).
- Modify the device enumeration code to turn off all of the unused
ACPI power resources at the end (Rafael Wysocki).
- Change the ACPI power resources handling code to turn off unused
ACPI power resources without checking their status which should not
be necessary by the spec (Rafael Wysocki).
- Add empty stubs for CPPC-related functions to be used when
CONFIG_ACPI_CPPC_LIB is not set (Rafael Wysocki).
- Simplify device enumeration code (Rafael Wysocki).
- Change device enumeration code to use match_string() for string
matching (Andy Shevchenko).
- Modify irqresource_disabled() to retain the resouce flags that have
been set already (Angela Czubak).
- Add native backlight whitelist entry for GA401/GA502/GA503 (Luke
Jones).
- Modify the ACPI backlight driver to let the native backlight
handling take over on hardware-reduced systems (Hans de Goede).
- Introduce acpi_dev_get() and switch over the ACPI core code to
using it (Andy Shevchenko).
- Use kobj_attribute as callback argument instead of a local struct
type in the CPPC linrary code (Nathan Chancellor).
- Drop unneeded initializatio of a static variable from the ACPI
processor driver (Tian Tao).
- Drop unnecessary local variable assignment from the ACPI APEI code
(Colin Ian King).
- Document for_each_acpi_dev_match() macro (Andy Shevchenko).
- Address assorted coding style issues in multiple places (Xiaofei
Tan).
- Capitalize TLAs in a few comments (Andy Shevchenko).
- Correct assorted typos in comments (Tom Saeger)"
* tag 'acpi-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (68 commits)
ACPI: video: use native backlight for GA401/GA502/GA503
ACPI: APEI: remove redundant assignment to variable rc
ACPI: utils: Capitalize abbreviations in the comments
ACPI: utils: Document for_each_acpi_dev_match() macro
ACPI: bus: Introduce acpi_dev_get() and reuse it in ACPI code
ACPI: scan: Utilize match_string() API
resource: Prevent irqresource_disabled() from erasing flags
ACPI: CPPC: Replace cppc_attr with kobj_attribute
ACPI: scan: Call acpi_get_object_info() from acpi_set_pnp_ids()
ACPI: scan: Drop sta argument from acpi_init_device_object()
ACPI: scan: Drop sta argument from acpi_add_single_object()
ACPI: scan: Rearrange checks in acpi_bus_check_add()
ACPI: scan: Fold acpi_bus_type_and_status() into its caller
ACPI: video: Check LCD flag on ACPI-reduced-hardware devices
ACPI: utils: Add acpi_reduced_hardware() helper
ACPI: dock: fix some coding style issues
ACPI: sysfs: fix some coding style issues
ACPI: PM: add a missed blank line after declarations
ACPI: custom_method: fix a coding style issue
ACPI: CPPC: fix some coding style issues
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver updates freom Hans de Goede:
- lots of Microsoft Surface work
- platform-profile support for HP and Microsoft Surface devices
- new WMI Gigabyte motherboard temperature monitoring driver
- Intel PMC improvements for Tiger Lake and Alder Lake
- misc bugfixes, improvements and quirk additions all over
* tag 'platform-drivers-x86-v5.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (87 commits)
platform/x86: gigabyte-wmi: add support for B550M AORUS PRO-P
platform/x86: intel_pmc_core: Uninitialized data in pmc_core_lpm_latch_mode_write()
platform/x86: intel_pmc_core: add ACPI dependency
platform/surface: aggregator: fix a bit test
platform/x86: intel_pmc_core: Fix "unsigned 'ret' is never less than zero" smatch warning
platform/x86: touchscreen_dmi: Add info for the Teclast Tbook 11 tablet
platform/x86: intel_pmc_core: Add support for Alder Lake PCH-P
platform/x86: intel_pmc_core: Add LTR registers for Tiger Lake
platform/x86: intel_pmc_core: Add option to set/clear LPM mode
platform/x86: intel_pmc_core: Add requirements file to debugfs
platform/x86: intel_pmc_core: Get LPM requirements for Tiger Lake
platform/x86: intel_pmc_core: Show LPM residency in microseconds
platform/x86: intel_pmc_core: Handle sub-states generically
platform/x86: intel_pmc_core: Remove global struct pmc_dev
platform/x86: intel_pmc_core: Don't use global pmcdev in quirks
platform/x86: intel_chtdc_ti_pwrbtn: Fix missing IRQF_ONESHOT as only threaded handler
platform/x86: gigabyte-wmi: add X570 AORUS ELITE
platform/x86: thinkpad_acpi: Add labels to the first 2 temperature sensors
platform/x86: pmc_atom: Match all Beckhoff Automation baytrail boards with critclk_systems DMI table
platform/x86: add Gigabyte WMI temperature driver
...
|
|
This release adds following changes:
- Support increased number of CPUs
- Return error when mailbox commmand fails to enable core-power
- Option to online all CPUs
- Removes build date and time print
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
These macros introduce nondeterminism in builds, and break reproducible
builds.
Signed-off-by: Antonio Terceiro <antonio.terceiro@linaro.org>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
