Age | Commit message (Collapse) | Author | Files | Lines |
|
When the DSP is suspended while the firmware is in the crashed state, we
skip tearing down the pipelines. This means that the widget reference
counts will not get to reset to 0 before suspend. This will lead to
errors with resuming audio after system resume. To fix this, invoke the
tear_down_all_pipelines op before skipping to DSP suspend.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Curtis Malainey <cujomalainey@chromium.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20221220125629.8469-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If the DSP crashes before the system suspends, the setting of target state
will be skipped because the firmware state will no longer be
SOF_FW_BOOT_COMPLETE. This leads to the incorrect assumption that the
DSP should suspend to D0I3 instead of suspending to D3. To fix this,
set the target_state before we skip to DSP suspend even when the DSP has
crashed.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Curtis Malainey <cujomalainey@chromium.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20221220125629.8469-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
While not quite as bogus as for the dma-coherent allocations that were
fixed earlier, GFP_COMP for these allocations has no benefits for
the dma-direct case, and can't be supported at all by dma dma-iommu
backend which splits up allocations into smaller orders. Due to an
oversight in ffcb75458460 that flag stopped being cleared for all
dma allocations, but only got rejected for coherent ones.
Start fixing this by not requesting __GFP_COMP in the sound code, which
is the only place that did this.
Fixes: ffcb75458460 ("dma-mapping: reject __GFP_COMP in dma_alloc_attrs")
Reported-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Reported-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Tested-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire
Pull soundwire updates from Vinod Koul:
"This include bunch of Intel driver code reorganization and support for
qcom v1.7.0 controller:
- intel: reorganization of hw_ops callbacks, splitting files etc
- qcom: support for v1.7.0 qcom controllers"
* tag 'soundwire-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire:
soundwire: intel: split auxdevice to different file
soundwire: intel: add in-band wake callbacks in hw_ops
soundwire: intel: add link power management callbacks in hw_ops
soundwire: intel: add bus management callbacks in hw_ops
soundwire: intel: add register_dai callback in hw_ops
soundwire: intel: add debugfs callbacks in hw_ops
soundwire: intel: start using hw_ops
dt-bindings: soundwire: Convert text bindings to DT Schema
soundwire: cadence: use dai_runtime_array instead of dma_data
soundwire: cadence: rename sdw_cdns_dai_dma_data as sdw_cdns_dai_runtime
soundwire: qcom: add support for v1.7 Soundwire Controller
dt-bindings: soundwire: qcom: add v1.7.0 support
soundwire: qcom: make reset optional for v1.6 controller
soundwire: qcom: remove unused SWRM_SPECIAL_CMD_ID
soundwire: dmi-quirks: add quirk variant for LAPBC710 NUC15
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of driver core and kernfs changes for 6.2-rc1.
The "big" change in here is the addition of a new macro,
container_of_const() that will preserve the "const-ness" of a pointer
passed into it.
The "problem" of the current container_of() macro is that if you pass
in a "const *", out of it can comes a non-const pointer unless you
specifically ask for it. For many usages, we want to preserve the
"const" attribute by using the same call. For a specific example, this
series changes the kobj_to_dev() macro to use it, allowing it to be
used no matter what the const value is. This prevents every subsystem
from having to declare 2 different individual macros (i.e.
kobj_const_to_dev() and kobj_to_dev()) and having the compiler enforce
the const value at build time, which having 2 macros would not do
either.
The driver for all of this have been discussions with the Rust kernel
developers as to how to properly mark driver core, and kobject,
objects as being "non-mutable". The changes to the kobject and driver
core in this pull request are the result of that, as there are lots of
paths where kobjects and device pointers are not modified at all, so
marking them as "const" allows the compiler to enforce this.
So, a nice side affect of the Rust development effort has been already
to clean up the driver core code to be more obvious about object
rules.
All of this has been bike-shedded in quite a lot of detail on lkml
with different names and implementations resulting in the tiny version
we have in here, much better than my original proposal. Lots of
subsystem maintainers have acked the changes as well.
Other than this change, included in here are smaller stuff like:
- kernfs fixes and updates to handle lock contention better
- vmlinux.lds.h fixes and updates
- sysfs and debugfs documentation updates
- device property updates
All of these have been in the linux-next tree for quite a while with
no problems"
* tag 'driver-core-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (58 commits)
device property: Fix documentation for fwnode_get_next_parent()
firmware_loader: fix up to_fw_sysfs() to preserve const
usb.h: take advantage of container_of_const()
device.h: move kobj_to_dev() to use container_of_const()
container_of: add container_of_const() that preserves const-ness of the pointer
driver core: fix up missed drivers/s390/char/hmcdrv_dev.c class.devnode() conversion.
driver core: fix up missed scsi/cxlflash class.devnode() conversion.
driver core: fix up some missing class.devnode() conversions.
driver core: make struct class.devnode() take a const *
driver core: make struct class.dev_uevent() take a const *
cacheinfo: Remove of_node_put() for fw_token
device property: Add a blank line in Kconfig of tests
device property: Rename goto label to be more precise
device property: Move PROPERTY_ENTRY_BOOL() a bit down
device property: Get rid of __PROPERTY_ENTRY_ARRAY_EL*SIZE*()
kernfs: fix all kernel-doc warnings and multiple typos
driver core: pass a const * into of_device_uevent()
kobject: kset_uevent_ops: make name() callback take a const *
kobject: kset_uevent_ops: make filter() callback take a const *
kobject: make kobject_namespace take a const *
...
|
|
Since commit fc7a6209d571 ("bus: Make remove callback return void")
forces bus_type::remove be void-returned, it doesn't make much sense for
any bus based driver implementing remove callbalk to return non-void to
its caller.
This change is for xen bus based drivers.
Acked-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Dawei Li <set_pte_at@outlook.com>
Link: https://lore.kernel.org/r/TYCP286MB23238119AB4DF190997075C9CAE39@TYCP286MB2323.JPNP286.PROD.OUTLOOK.COM
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
lochnagar_of_match is used unconditionally, so COMPILE_TEST builds
without OF warn:
sound/soc/codecs/lochnagar-sc.c:247:34: error: ‘lochnagar_of_match’ defined but not used [-Werror=unused-const-variable=]
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221215134337.77944-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The bytcr_rt5640.c file already supports the HP Stream 7.
The HP Stream 8 is almost identical in terms of the hardware
with the exception of it having stereo speakers, a SIM
card slot and the obvious size difference.
Signed-off-by: Moises Cardona <moisesmcardona@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20221214120830.1572474-1-moisesmcardona@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This looks like a relatively calm development cycle; there have been
only few changes in ALSA and ASoC core sides while we get lots of
device-specific fixes and updates as usual. Most of commits are about
ASoC, including Intel SOF/AVS and many device tree updates.
Below are some highlights:
Core:
- Improvement in memalloc helper for fallback allocations
- More cleanups of ASoC DAPM code
ASoC:
- Factoring out of mapping hw_params onto SoundWire configuration
- The ever ongoing overhauls of the Intel DSP code continue,
including support for loading libraries and probes with IPC4 on
SOF.
- Support for more sample formats on JZ4740
- Lots of device tree conversions and fixups
- Support for Allwinner D1, a range of AMD and Intel systems,
Mediatek systems with multiple DMICs, Nuvoton NAU8318, NXP
fsl_rpmsg and i.MX93, Qualcomm AudioReach Enable, MFC and SAL,
RealTek RT1318 and Rockchip RK3588
ALSA:
- Addition of PCM kselftest; still minimalistic but can be extended
in future
- Fixes for corner-case XRUNs with USB-audio implicit feedback mode
- Usual device-specific quirk updates for USB- and HD-audio
- FireWire DICE updates
This also contains a few cross-tree updates:
- Some OMAP board file updates for removal of relevant OMAP platforms
- A new I2C API update for I2C probe API adaption
- A DRM update for the further hdmi-codec updates"
* tag 'sound-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (417 commits)
ALSA: mts64: fix possible null-ptr-defer in snd_mts64_interrupt
ALSA: patch_realtek: Fix Dell Inspiron Plus 16
ALSA: hda/cirrus: Add extra 10 ms delay to allow PLL settle and lock.
ASoC: dt-bindings: Correct Alexandre Belloni email
ASoC: dt-bindings: maxim,max98504: Convert to DT schema
ASoC: dt-bindings: maxim,max98357a: Convert to DT schema
ASoC: dt-bindings: Reference common DAI properties
ASoC: dt-bindings: Extend name-prefix.yaml into common DAI properties
ASoC: rt715: Make read-only arrays capture_reg_H and capture_reg_L static const
ASoC: uniphier: aio-core: Make some read-only arrays static const
ASoC: wcd938x: Make read-only array minCode_param static const
ASoC: qcom: lpass-sc7280: Add maybe_unused tag for system PM ops
ASoC : SOF: amd: Add support for IPC and DSP dumps
ASoC: SOF: amd: Use poll function instead to read ACP_SHA_DSP_FW_QUALIFIER
ALSA: usb-audio: Workaround for XRUN at prepare
ALSA: pcm: Handle XRUN at trigger START
ALSA: pcm: Set missing stop_operating flag at undoing trigger start
drm: tda99x: Don't advertise non-existent capture support
ASoC: hdmi-codec: Allow playback and capture to be disabled
kselftest/alsa: Add more coverage of sample rates and channel counts
...
|
|
Coverity spotted that panic_info is not initialized to zero in
mtk_adsp_dump. Using uninitialized value panic_info.linenum when
calling snd_sof_get_status. Fix this coverity by initializing
panic_info struct as zero.
Signed-off-by: YC Hung <yc.hung@mediatek.com>
Reviewed-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20221213115617.25086-1-yc.hung@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
For some reason rt5670_i2c_probe() does a pm_runtime_put() at the end
of a successful probe. But it has never done a pm_runtime_get() leading
to the following error being logged into dmesg:
rt5670 i2c-10EC5640:00: Runtime PM usage count underflow!
Fix this by removing the unnecessary pm_runtime_put().
Fixes: 64e89e5f5548 ("ASoC: rt5670: Add runtime PM support")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20221213123319.11285-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The Advantech MICA-071 tablet deviates from the defaults for
a non CR Bay Trail based tablet in several ways:
1. It uses an analog MIC on IN3 rather then using DMIC1
2. It only has 1 speaker
3. It needs the OVCD current threshold to be set to 1500uA instead of
the default 2000uA to reliable differentiate between headphones vs
headsets
Add a quirk with these settings for this tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20221213123246.11226-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- reduce the swiotlb buffer size on allocation failure (Alexey
Kardashevskiy)
- clean up passing of bogus GFP flags to the dma-coherent allocator
(Christoph Hellwig)
* tag 'dma-mapping-6.2-2022-12-13' of git://git.infradead.org/users/hch/dma-mapping:
dma-mapping: reject __GFP_COMP in dma_alloc_attrs
ALSA: memalloc: don't pass bogus GFP_ flags to dma_alloc_*
s390/ism: don't pass bogus GFP_ flags to dma_alloc_coherent
cnic: don't pass bogus GFP_ flags to dma_alloc_coherent
RDMA/qib: don't pass bogus GFP_ flags to dma_alloc_coherent
RDMA/hfi1: don't pass bogus GFP_ flags to dma_alloc_coherent
media: videobuf-dma-contig: use dma_mmap_coherent
swiotlb: reduce the swiotlb buffer size on allocation failure
|
|
Merge series from Kai Vehmanen <kai.vehmanen@linux.intel.com>:
This patchset is an alternative solution to problems
reported by Ricardo Ribalda <ribalda@chromium.org> and
Zhen Ni <nizhen@uniontech.com>, as discussed in
- "[PATCH] ALSA: core: Fix deadlock when shutdown a frozen userspace"
https://mailman.alsa-project.org/pipermail/alsa-devel/2022-November/209248.html
- "[PATCH] ASoc: SOF: Fix sof-audio-pci-intel-tgl shutdown timeout during hibernation"
https://mailman.alsa-project.org/pipermail/alsa-devel/2022-December/209685.html
It was raised by Oliver Neukum <oneukum@suse.com> that kernel should
not let user-space stall the shutdown process in any scenario and the
unregister call in current SOF shutdown code is not right.
This series reverts the ASoC SOF patch to unregister clients and
the machine drivers at shutdown. To avoid bringing back old bugs,
the series includes a patch to fix S5 entry on certain Intel
platforms.
|
|
The unique ID is determined by the ADR pin level of rt1318.
ODM changed design, update codec addr to match new design.
Fixes: 0050e3d3d43d ("ASoC: Intel: soc-acpi: add SKU 0C11 SoundWire configuration")
Signed-off-by: Gongjun Song <gongjun.song@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20221212085527.1886168-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
rk_spdif_runtime_resume()
rk_spdif_runtime_resume() may have called clk_prepare_enable() before return
from failed branches, add missing clk_disable_unprepare() in this case.
Fixes: f874b80e1571 ("ASoC: rockchip: Add rockchip SPDIF transceiver driver")
Signed-off-by: Wang Jingjin <wangjingjin1@huawei.com>
Link: https://lore.kernel.org/r/20221208063900.4180790-1-wangjingjin1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix this by dropping wm8994->accdet_lock while calling
cancel_delayed_work_sync(&wm8994->mic_work) in wm1811_jackdet_irq().
Fixes: c0cc3f166525 ("ASoC: wm8994: Allow a delay between jack insertion and microphone detect")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221209091657.1183-1-m.szyprowski@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In MT8195 SOF design, both DSP and audio driver would access audio
registers. Before DSP accesses audio registers, audio power and clock
should be enabled. DSP will hang up if DSP access audio register but
audio power and clock are disabled. Therefore, we add audio pm runtime
active checking before accessing audio registers in SOF BE's callback
hw_params function to avoid this situation.
Signed-off-by: YC Hung <yc.hung@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20221209031053.8444-1-yc.hung@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The unregister machine drivers call is not safe to do when
kexec is used. Kexec-lite gets blocked with following backtrace:
[ 84.943749] Freezing user space processes ... (elapsed 0.111 seconds) done.
[ 246.784446] INFO: task kexec-lite:5123 blocked for more than 122 seconds.
[ 246.819035] Call Trace:
[ 246.821782] <TASK>
[ 246.824186] __schedule+0x5f9/0x1263
[ 246.828231] schedule+0x87/0xc5
[ 246.831779] snd_card_disconnect_sync+0xb5/0x127
...
[ 246.889249] snd_sof_device_shutdown+0xb4/0x150
[ 246.899317] pci_device_shutdown+0x37/0x61
[ 246.903990] device_shutdown+0x14c/0x1d6
[ 246.908391] kernel_kexec+0x45/0xb9
This reverts commit 83bfc7e793b555291785136c3ae86abcdc046887.
Reported-by: Ricardo Ribalda <ribalda@chromium.org>
Cc: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20221209114529.3909192-3-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If system shutdown has not been completed cleanly, it is possible the
DMA stream shutdown has not been done, or was not clean.
If this is the case, Intel TGL/ADL HDA platforms may fail to shutdown
cleanly due to pending HDA DMA transactions. To avoid this, detect this
scenario in the shutdown callback, and perform an additional controller
reset. This has been tested to unblock S5 entry if this condition is
hit.
Co-developed-by: Archana Patni <archana.patni@intel.com>
Signed-off-by: Archana Patni <archana.patni@intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20221209114529.3909192-2-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When the new style KAE keep-alive implementation is used on compatible
Intel hardware, the clocks are maintained when codec is in D3. The
generic code in hda_cleanup_all_streams() can however interfere with
generation of audio samples in this mode, by setting the stream and
channel ids to zero.
To get full benefit of the keepalive, set the new
no_stream_clean_at_suspend quirk bit on affected Intel hardware. When
this bit is set, stream cleanup is skipped in hda_call_codec_suspend().
Special handling is needed for the case when system goes to suspend. The
stream id programming can be lost in this case. This will also cause
codec->cvt_setups to be out of sync. Handle this by implementing custom
suspend/resume handlers. If keep-alive is active for any converter, set
the quirk flags no_stream_clean_at_suspend and forced_resume. Upon
resume, keepalive programming is restored if needed.
Fixes: 15175a4f2bbb ("ALSA: hda/hdmi: add keep-alive support for ADL-P and DG2")
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20221209101822.3893675-4-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
If the stream-id is zero, the keep-alive (KAE) will only ensure clock is
generated, but no audio samples are sent over display link. This happens
before first real audio stream is played out to a newly connected
receiver.
Reuse the code in silent_stream_enable() to set up stream parameters
to sane defaults values, also when using the newer keep-alive flow.
Fixes: 15175a4f2bbb ("ALSA: hda/hdmi: add keep-alive support for ADL-P and DG2")
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Tested-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://lore.kernel.org/r/20221209101822.3893675-3-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The i915 display codec may not successfully transition to
normal audio streaming mode, if the stream id is programmed
while codec is actively transmitting data. This can happen
when silent stream is enabled in KAE mode.
Fix the issue by implementing a i915 specific programming
flow, where the silent streaming is temporarily stopped,
a small delay is applied to ensure display codec becomes
idle, and then proceed with reprogramming the stream ID.
Fixes: 15175a4f2bbb ("ALSA: hda/hdmi: add keep-alive support for ADL-P and DG2")
Link: https://gitlab.freedesktop.org/drm/intel/-/issues/7353
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Tested-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://lore.kernel.org/r/20221209101822.3893675-2-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Scenario when snd_hdac_stream_setup_periods() receives an instance of
struct hdac_stream with neither ->substream nor ->cstream initialized is
invalid.
Simultaneously addresses "uninitialized symbol 'dmab'" error reported by
Smatch.
Fixes: 3e9582267e3a ("ALSA: hda: Interrupt servicing and BDL setup for compress streams")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221208142635.1514944-1-cezary.rojewski@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v6.2
A few more updates for v6.2 which can hopefully go into a later pull
request, the bulk of these are fixes, minor cleanups or new board quirks
- the one big bit that isn't is support for getting diagnostic data out
of the Intel AVS firmwares.
|
|
DAIs parameters should be cleared if there's no active stream. Before,
we implemented it in soc_pcm_hw_free() by detecting stream_active. If
the running stream is the last active stream, we're going to clear
parameters.
However it will cause DAIs parameters never be cleared if there're
more than one stream. For example, we have stream1 and stream2 about
to stop. stream2 executes soc_pcm_hw_free() before stream1 executes
soc_pcm_close(). At the moment, stream2 should clear DAIs parameters.
Since stream_active is not yet updated by stream1 in soc_pcm_close(),
stream2 will not clear DAIs parameters. In result both stream1 and
stream2 don't clear the parameters.
This patch moves DAIs parameters cleanup after stream_active is
updated.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Link: https://lore.kernel.org/r/20221128060950.3540845-1-chancel.liu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The function wcd_clsh_set_buck_mode() is defined in the wcd-clsh-v2.c
file, but not called elsewhere, so remove this unused function.
sound/soc/codecs/wcd-clsh-v2.c:133:20: warning: unused function 'wcd_clsh_enable_status'.
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=3348
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Link: https://lore.kernel.org/r/20221205073507.36071-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>:
One new JasperLake configuration, core refactoring between RT1316 and
RT1318 and a minor uninitialized variable corner case.
|
|
Merge series from Cezary Rojewski <cezary.rojewski@intel.com>:
Even though skylake-driver is going to be replaced by the avs-driver,
the goal is to keep it functional on all the configurations it supports
until its EOL. When comparing chrome trees against upstream
skylake-driver, couple fixes pop up that are not part of upstream
repository. These fixes are backed up by real bugs (issue trackers),
address real problems. There is no reason for them to stay in the
internal tree.
Patches 1-4 combined together address issue where the driver updates the
presumably static audio format descriptions coming from the topology
files through its "fixup" functions. As long as given audio format is
used by a single path, nothing collides and any updates are harmless.
However, when multiple paths e.g.: DMIC and HDMI1 utilize the same audio
format descriptor, any updates caused by the opening of the first path,
may cause the second to fail.
The 5th change from the set fixes driver hang sporadically occurring
during shutdown procedure. Once HDAudio links are powered down along
with the AudioDSP, the hang stops reproducing.
The last change helps survive in environments with limited/fragmented
memory. While the BDL is small already, other buffers can be allocated
using scatter-gather. This basically aligns the code with what the
avs-driver does.
|
|
mt8183_mt6358_ts3a227_max98357_dev_probe()
The node returned by of_parse_phandle() with refcount incremented,
of_node_put() needs be called when finish using it. So add it in the
error path in mt8183_mt6358_ts3a227_max98357_dev_probe().
Fixes: 11c0269017b2 ("ASoC: Mediatek: MT8183: Add machine driver with TS3A227")
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Link: https://lore.kernel.org/r/1670234188-23596-1-git-send-email-wangyufen@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Follow the advice of the Documentation/filesystems/sysfs.rst and show()
should only use sysfs_emit() or sysfs_emit_at() when formatting the
value to be returned to user space.
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Link: https://lore.kernel.org/r/202212051943476482106@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
rockchip_pdm_runtime_resume()
The clk_disable_unprepare() should be called in the error handling of
rockchip_pdm_runtime_resume().
Fixes: fc05a5b22253 ("ASoC: rockchip: add support for pdm controller")
Signed-off-by: Wang Jingjin <wangjingjin1@huawei.com>
Link: https://lore.kernel.org/r/20221205032802.2422983-1-wangjingjin1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The of_get_next_child() returns a node with refcount incremented, and
decrements the refcount of prev. So in the error path of the while loop,
of_node_put() needs be called for cpu_ep.
Fixes: fce9b90c1ab7 ("ASoC: audio-graph-card: cleanup DAI link loop method - step2")
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/1670228127-13835-1-git-send-email-wangyufen@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
mt8173_rt5650_rt5514_dev_probe()
The node returned by of_parse_phandle() with refcount incremented,
of_node_put() needs be called when finish using it. So add it in the
error path in mt8173_rt5650_rt5514_dev_probe().
Fixes: 0d1d7a664288 ("ASoC: mediatek: Refine mt8173 driver and change config option")
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Link: https://lore.kernel.org/r/1670234664-24246-1-git-send-email-wangyufen@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
'ret' will not be initialized if dai_fmt is not DSP_A or DSP_B.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20221206212507.359993-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
sof_sdw_rt1308.c/sof_sdw_rt1316.c/sof_sdw_rt1318.c handle amp
in basically the same way, optimized and merged into one file.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Gongjun Song <gongjun.song@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20221206212507.359993-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This configuration supports JSL boards which implement ALC5682I-VD/VS
on SSP0 port.
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Brent Lu <brent.lu@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20221206212507.359993-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Resign from ->alloc_dma_buf() and use snd_dma_alloc_pages() directly.
For data i.e.: base firmware binary transfer, make use of SG allocation
to better adapt to memory-limited environment. For BDL descriptor, given
its small size this is not required.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Tested-by: Lukasz Majczak <lma@semihlaf.com>
Link: https://lore.kernel.org/r/20221205085330.857665-7-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
AudioDSP cores and HDAudio links need to be turned off on shutdown to
ensure no communication or data transfer occurs during the procedure.
Fixes: c5a76a246989 ("ASoC: Intel: Skylake: Add shutdown callback")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Tested-by: Lukasz Majczak <lma@semihlaf.com>
Link: https://lore.kernel.org/r/20221205085330.857665-6-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Provide a single location for pipe config selection where all fields
that have to be updated whenever ->pipe_config_idx changes can be
updated accordingly.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Tested-by: Lukasz Majczak <lma@semihlaf.com>
Link: https://lore.kernel.org/r/20221205085330.857665-5-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Field ->pipe_config_idx duplicates the job of ->cur_config_idx so
remove it.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Tested-by: Lukasz Majczak <lma@semihlaf.com>
Link: https://lore.kernel.org/r/20221205085330.857665-4-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Rather than forcing userspace to select proper format with enumerable
kcontrols, select it ourselves based on provided hw_params.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Tested-by: Lukasz Majczak <lma@semihlaf.com>
Link: https://lore.kernel.org/r/20221205085330.857665-3-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Without updating the index before BE copier config is filled with
hardware parameters, outdated parameters are used instead.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Tested-by: Lukasz Majczak <lma@semihlaf.com>
Link: https://lore.kernel.org/r/20221205085330.857665-2-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Lenovo TianYi510Pro-14IOB (17aa:3742)
require quirk for enabling headset-mic
Signed-off-by: Edward Pacman <edward@edward-p.xyz>
Cc: <stable@vger.kernel.org>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216756
Link: https://lore.kernel.org/r/20221207133218.18989-1-edward@edward-p.xyz
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add relevant information to the quirks-table.h file.
The test passes and the sound source file plays normally.
Signed-off-by: wangdicheng <wangdicheng@kylinos.cn>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/SG2PR02MB587849631CB96809CF90DBED8A1A9@SG2PR02MB5878.apcprd02.prod.outlook.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
HDMI audio is not working on the HP EliteDesk 800 G6 because the pin is
unconnected. This issue can be resolved by using the 'hdajackretask'
tool to override the unconnected pin to force it to connect.
Signed-off-by: Jiao Zhou <jiaozhou@google.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20221206185311.3669950-1-jiaozhou@google.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v6.2
This is a fairly sedate release for the core code, but there's been a
lot of driver work especially around the x86 platforms and device tree
updates:
- More cleanups of the DAPM code from Morimoto-san.
- Factoring out of mapping hw_params onto SoundWire configuration by
Charles Keepax.
- The ever ongoing overhauls of the Intel DSP code continue, including
support for loading libraries and probes with IPC4 on SOF.
- Support for more sample formats on JZ4740.
- Lots of device tree conversions and fixups.
- Support for Allwinner D1, a range of AMD and Intel systems, Mediatek
systems with multiple DMICs, Nuvoton NAU8318, NXP fsl_rpmsg and
i.MX93, Qualcomm AudioReach Enable, MFC and SAL, RealTek RT1318 and
Rockchip RK3588
There's more cross tree updates than usual, though all fairly minor:
- Some OMAP board file updates that were depedencies for removing their
providers in ASoC, as part of a wider effort removing the support for
the relevant OMAP platforms.
- A new I2C API required for updates to the new I2C probe API.
- A DRM update making use of a new API for fixing the capabilities
advertised via hdmi-codec.
Since this is being sent early I might send some more stuff if you've
not yet sent your pull request and there's more come in.
|
|
I got a null-ptr-defer error report when I do the following tests
on the qemu platform:
make defconfig and CONFIG_PARPORT=m, CONFIG_PARPORT_PC=m,
CONFIG_SND_MTS64=m
Then making test scripts:
cat>test_mod1.sh<<EOF
modprobe snd-mts64
modprobe snd-mts64
EOF
Executing the script, perhaps several times, we will get a null-ptr-defer
report, as follow:
syzkaller:~# ./test_mod.sh
snd_mts64: probe of snd_mts64.0 failed with error -5
modprobe: ERROR: could not insert 'snd_mts64': No such device
BUG: kernel NULL pointer dereference, address: 0000000000000000
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
PGD 0 P4D 0
Oops: 0002 [#1] PREEMPT SMP PTI
CPU: 0 PID: 205 Comm: modprobe Not tainted 6.1.0-rc8-00588-g76dcd734eca2 #6
Call Trace:
<IRQ>
snd_mts64_interrupt+0x24/0xa0 [snd_mts64]
parport_irq_handler+0x37/0x50 [parport]
__handle_irq_event_percpu+0x39/0x190
handle_irq_event_percpu+0xa/0x30
handle_irq_event+0x2f/0x50
handle_edge_irq+0x99/0x1b0
__common_interrupt+0x5d/0x100
common_interrupt+0xa0/0xc0
</IRQ>
<TASK>
asm_common_interrupt+0x22/0x40
RIP: 0010:_raw_write_unlock_irqrestore+0x11/0x30
parport_claim+0xbd/0x230 [parport]
snd_mts64_probe+0x14a/0x465 [snd_mts64]
platform_probe+0x3f/0xa0
really_probe+0x129/0x2c0
__driver_probe_device+0x6d/0xc0
driver_probe_device+0x1a/0xa0
__device_attach_driver+0x7a/0xb0
bus_for_each_drv+0x62/0xb0
__device_attach+0xe4/0x180
bus_probe_device+0x82/0xa0
device_add+0x550/0x920
platform_device_add+0x106/0x220
snd_mts64_attach+0x2e/0x80 [snd_mts64]
port_check+0x14/0x20 [parport]
bus_for_each_dev+0x6e/0xc0
__parport_register_driver+0x7c/0xb0 [parport]
snd_mts64_module_init+0x31/0x1000 [snd_mts64]
do_one_initcall+0x3c/0x1f0
do_init_module+0x46/0x1c6
load_module+0x1d8d/0x1e10
__do_sys_finit_module+0xa2/0xf0
do_syscall_64+0x37/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
</TASK>
Kernel panic - not syncing: Fatal exception in interrupt
Rebooting in 1 seconds..
The mts wa not initialized during interrupt, we add check for
mts to fix this bug.
Fixes: 68ab801e32bb ("[ALSA] Add snd-mts64 driver for ESI Miditerminal 4140")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Link: https://lore.kernel.org/r/20221206061004.1222966-1-cuigaosheng1@huawei.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Merge series from Cezary Rojewski <cezary.rojewski@intel.com>:
The patchset focuses on debug functionality for the avs-driver.
Two major blocks are covered here: data probing and AudioDSP firmware
logging. Both are configured and controlled through debugfs.
Data probing is a AudioDSP debug functionality which allows for
gathering the actual data that is being routed to or from a module.
Helps in debugging its processing capabilities - navigate to a specific
module which may have caused a glitch within a pipeline (set of modules
bound together).
First few allow for assigning compress stream to a HDAudio stream, what
is currently limited to pcm substreams only. These patches were already
present on this list and reviewed in the past [1].
The next few tidy existing debug-related code up so it's ready for
addition of new functionalities and make it clear which part of the avs
is debug related and which is not. These also simplify the existing
locking around the trace fifo.
Afterward, debug-related IPCs are defined along with stub soc-component
and compress DAI operations. Not much is done there as it's not a
standard PCM streaming scenario. Most code found in compress operations
is inherited from the HOST side of HDAudio streaming found in pcm.c
file of the driver.
Finally, a debugfs file operations are defined. These facilitate
connecting to DSP modules from which the data shall be gathered as well
as control and configuration of firmware logging. Additionally, entries
are added to allow for dumping snapshots of key memory windows.
|
|
sof_es8336_remove() calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This
means that the callback function may still be running after
the driver's remove function has finished, which would result
in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Fixes: 89cdb224f2ab ("ASoC: sof_es8336: reduce pop noise on speaker")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20221205143721.3988988-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|