| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The recent endpoint management change for implicit feedback mode added
a clearance of ep->sync_sink (formerly ep->sync_slave) pointer at
snd_usb_endpoint_stop() to assure no leftover for the feedback from
the already stopped capture stream. This turned out to cause a
regression, however, when full-duplex streams were running and only a
capture was stopped. Because of the above clearance of ep->sync_sink
pointer, no more feedback is done, hence the playback will stall.
This patch fixes the ep->sync_sink clearance to be done only after all
endpoints are released, for addressing the regression.
Reported-and-tested-by: Lucas Endres <jaffa225man@gmail.com>
Fixes: bf6313a0ff76 ("ALSA: usb-audio: Refactor endpoint management")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210426063349.18601-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Through the examinations and experiments with lots of Roland and BOSS
USB-audio devices, we found out that the recently introduced
full-duplex operations with the implicit feedback mode work fine for
quite a few devices, while the others need only the capture-side quirk
to enforce the full-duplex mode. The recent commit d86f43b17ed4
("ALSA: usb-audio: Add support for many Roland devices' implicit
feedback quirks") tried to add such quirk entries manually in the
lists, but this turned out to be too many and error-prone, hence it
was reverted again.
This patch is another attempt to cover those missing Roland/BOSS
devices but in a more generic way. It matches the devices with the
vendor ID 0x0582, and checks whether they are with both ASYNC sync
types or ASYNC is only for capture device. In the former case, it's
the device with the implicit feedback mode, and applies accordingly.
In both cases, the capture stream requires always the full-duplex
mode, and we apply the known capture quirk for that, too.
Basically the already existing BOSS device quirk entries become
redundant after this generic matching, so those are removed. Although
the capture_implicit_fb_quirks[] table became empty and superfluous, I
keep it for now, so that people can put a special device easily at any
time later again.
Link: https://lore.kernel.org/r/CAOsVg8rA61B=005_VyUwpw3piVwA7Bo5fs1GYEB054efyzGjLw@mail.gmail.com
Link: https://lore.kernel.org/r/20210414083255.9527-1-tiwai@suse.de
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=212519
Tested-by: Lucas Endres <jaffa225man@gmail.com>
Link: https://lore.kernel.org/r/20210422120413.457-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This reverts commit d86f43b17ed4 ("ALSA: usb-audio: Add support for
many Roland devices' feedback quirks").
It turned out that many quirk entries there don't contain the proper
EP values and/or the quirk types, which lead to the broken
operations.
As we're going to cover all Roland/BOSS devices in a more generic way
rather the explicit lists, let's revert the previous additions at
first.
Fixes: d86f43b17ed4 ("ALSA: usb-audio: Add support for many Roland devices' implicit feedback quirks")
Link: https://lore.kernel.org/r/20210422120413.457-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Currently when the call to usb_urb_ep_type_check fails (returning -EINVAL)
the error return path returns -ENOMEM via the exit label "error". Other
uses of the same error exit label set the err variable to -ENOMEM but this
is not being used. I believe the original intent was for the error exit
path to return the value in err rather than the hard coded -ENOMEM, so
return this rather than the hard coded -ENOMEM.
Addresses-Coverity: ("Unused value")
Fixes: 738d9edcfd44 ("ALSA: usb-audio: Add sanity checks for invalid EPs")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210420134719.381409-1-colin.king@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Pioneer devices are supposed to be working with the implicit feedback
mode, but so far the attempt to apply the implicit feedback caused
issues, hence we explicitly skipped the implicit feedback mode for
them. Recently, Geraldo discovered that the device actually works if
you skip the generic matching of the sync EPs for the capture stream.
That is, we should apply the implicit feedback setup for the playback
like other similar devices, while we need to return 1 from
audioformat_capture_quirk() so that no further matching will be done.
And, later on, Olivia reported later that the fiddling with the
capture quirk alone doesn't suffice for the test with speaker-test
program. This seems to be a similar case like the recently fixed BOSS
devices. Indeed, the problem could be addressed by setting
playback_first flag, which indicates that the playback URBs have to be
sent out at first even in the implicit feedback mode.
This patch implements the application of the implicit feedback to
Pioneer devices as described in the above. The former
skip_pioneer_sync_ep() was dropped, and instead we provide
is_pioneer_implicit_fb() to check the Pioneer devices that need the
implicit feedback. In the audioformat_implicit_fb_quirk(), simply
apply the implicit fb for playback and set chip->playback_first flag
if matching, and in audioformat_capture_quirk()(), it returns 1 for
skipping the generic EP sync handling.
Reported-by: Geraldo <geraldogabriel@gmail.com>
Tested-by: Olivia Mackintosh <livvy@base.nu>
Link: https://lore.kernel.org/r/s5ha6pygqfz.wl-tiwai@suse.de
Link: https://lore.kernel.org/r/20210419153918.450-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add case statement to set sample-rate for the DJM-750 Pioneer
mixer. This was included as part of another patch but I think it has
been archived on Patchwork and hasn't been merged.
Signed-off-by: Olivia Mackintosh <livvy@base.nu>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210418165901.25776-1-livvy@base.nu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
It makes USB audio capture and playback possible and pristine on my Roland
INTEGRA-7, Boutique D-05, and R-26, along with many more I've encountered
people having had issues with over the last decade or so.
Signed-off-by: Lucas Endres <jaffa225man@gmail.com>
Link: https://lore.kernel.org/r/CAOsVg8rA61B=005_VyUwpw3piVwA7Bo5fs1GYEB054efyzGjLw@mail.gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
During the recent rewrite of the implicit feedback support, we've
tested to apply the implicit fb on BOSS devices, but it failed, as the
capture stream didn't start without the playback. As the end result,
it got another type of quirk for tying both streams but starts
playback always (commit 6234fdc1cede "ALSA: usb-audio: Quirk for BOSS
GT-001").
Meanwhile, Mike Oliphant has tested the real implicit feedback mode
for the playback again with the latest code, and found out that it
actually works if the initial feedback sync is skipped; that is, on
those BOSS devices, the playback stream has to be started at first
without waiting for the capture URB completions. Otherwise it gets
stuck. In the rest operations after the capture stream processed, we
can take them as the implicit feedback source.
This patch is an attempt to improve the support for BOSS devices with
the implicit feedback mode in the way described above. It adds a new
flag to snd_usb_audio, playback_first, indicating that the playback
stream starts without sync with the initial capture completion. This
flag is set in the quirk table with the new IMPLICIT_FB_BOTH type.
Reported-and-tested-by: Mike Oliphant <oliphant@nostatic.org>
Link: https://lore.kernel.org/r/20210414083255.9527-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In the current code, we have some assumption that the audio clock
selector has been set up implicitly and don't want to touch it unless
it's really needed for the fallback autoclock setup. This works for
most devices but some seem having a problem. Partially this was
covered for the devices with a single connector at the initialization
phase (commit 086b957cc17f "ALSA: usb-audio: Skip the clock selector
inquiry for single connections"), but also there are cases where the
wrong clock set up is kept silently. The latter seems to be the cause
of the noises on Behringer devices.
In this patch, we explicitly set up the audio clock selector whenever
the appropriate node is found.
Reported-by: Geraldo Nascimento <geraldogabriel@gmail.com>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199327
Link: https://lore.kernel.org/r/CAEsQvcvF7LnO8PxyyCxuRCx=7jNeSCvFAd-+dE0g_rd1rOxxdw@mail.gmail.com
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210413084152.32325-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
ToneLab EX guitar pedal device requires the same quirk like ToneLab ST
for supporting the MIDI.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=212593
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210407144549.1530-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
UA-101 device and co are supported by another driver, snd-ua101, but
the USB audio class driver (snd-usb-audio) catches all and this
resulted in the lack of functionality like missing MIDI devices.
This patch introduces a sort of deny-listing for those devices to just
return -ENODEV at probe in snd-usb-audio driver, so that it falls back
to the probe by snd-ua101.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=212477
Link: https://lore.kernel.org/r/20210408075656.30184-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The implicit feedback quirk table contains the entries that also
appear in the capture quirks, and those are all handled to be
skipped. For the code simplicity, drop the duped entries in the
playback quirk table, and check the match with the capture quirk table
instead.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=212519
Link: https://lore.kernel.org/r/20210406113837.32041-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
There are a few calls of usb_driver_claim_interface() but all of those
miss the proper error checks, as reported by Coverity. This patch
adds those missing checks.
Along with it, replace the magic pointer with -1 with a constant
USB_AUDIO_IFACE_UNUSED for better readability.
Reported-by: coverity-bot <keescook+coverity-bot@chromium.org>
Addresses-Coverity-ID: 1475943 ("Error handling issues")
Addresses-Coverity-ID: 1475944 ("Error handling issues")
Addresses-Coverity-ID: 1475945 ("Error handling issues")
Fixes: b1ce7ba619d9 ("ALSA: usb-audio: claim autodetected PCM interfaces all at once")
Fixes: e5779998bf8b ("ALSA: usb-audio: refactor code")
Link: https://lore.kernel.org/r/202104051059.FB7F3016@keescook
Link: https://lore.kernel.org/r/20210406113534.30455-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
ALSA: control - add generic LED API
This patchset tries to resolve the diversity in the audio LED
control among the ALSA drivers. A new control layer registration
is introduced which allows to run additional operations on
top of the elementary ALSA sound controls.
A new control access group (three bits in the access flags)
was introduced to carry the LED group information for
the sound controls. The low-level sound drivers can just
mark those controls using this access group. This information
is not exported to the user space, but user space can
manage the LED sound control associations through sysfs
(last patch) per Mark's request. It makes things fully
configurable in the kernel and user space (UCM).
The actual state ('route') evaluation is really easy
(the minimal value check for all channels / controls / cards).
If there's more complicated logic for a given hardware,
the card driver may eventually export a new read-only
sound control for the LED group and do the logic itself.
The new LED trigger control code is completely separated
and possibly optional (there's no symbol dependency).
The full code separation allows eventually to move this
LED trigger control to the user space in future.
Actually it replaces the already present functionality
in the kernel space (HDA drivers) and allows a quick adoption
for the recent hardware (ASoC codecs including SoundWire).
snd_ctl_led 24576 0
The sound driver implementation is really easy:
1) call snd_ctl_led_request() when control LED layer should be
automatically activated
/ it calls module_request("snd-ctl-led") on demand /
2) mark all related kcontrols with
SNDRV_CTL_ELEM_ACCESS_SPK_LED or
SNDRV_CTL_ELEM_ACCESS_MIC_LED
Link: https://lore.kernel.org/r/20210317172945.842280-1-perex@perex.cz
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Logitech ConferenceCam Connect is a compound USB device with UVC and
UAC. Not 100% reproducible but sometimes it keeps responding STALL to
every control transfer once it receives get_freq request.
This patch adds 046d:0x084c to a snd_usb_get_sample_rate_quirk list.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=203419
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210324105153.2322881-1-ikjn@chromium.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Rear Mic on Lenovo P620 cannot record after S3, despite that there's no
error and the other two functions of the USB audio, Line In and Line
Out, work just fine.
The mic starts to work again after running userspace app like "alsactl
store". Following the lead, the evidence shows that as soon as connector
status is queried, the mic can work again.
So also check connector value on resume to "wake up" the USB audio to
make it functional.
This can be device specific, however I think this generic approach may
benefit more than one device.
Now the resume callback checks connector, and a new callback,
reset_resume, to also restore switches and volumes.
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20210325165918.22593-2-kai.heng.feng@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This is preparation for next patch, no functional change intended.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20210325165918.22593-1-kai.heng.feng@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"The majority of changes are various ASoC device/platform-specific
small fixes (including a removal of stale file) while the only common
change is a clk management fix in ASoC simple-card driver.
The rest are the usual HD-audio quirks"
* tag 'sound-5.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (44 commits)
ALSA: usb-audio: Fix unintentional sign extension issue
ALSA: hda/realtek: fix mute/micmute LEDs for HP 850 G8
ASoC: dt-bindings: fsl_spdif: Add compatible string for new platforms
ASoC: rt711: add snd_soc_component remove callback
ASoC: rt5659: Update MCLK rate in set_sysclk()
ASoC: simple-card-utils: Do not handle device clock
ALSA: hda/realtek: fix mute/micmute LEDs for HP 440 G8
ALSA: hda/realtek: fix mute/micmute LEDs for HP 840 G8
ALSA: hda/realtek: apply pin quirk for XiaomiNotebook Pro
ALSA: hda/realtek: Apply headset-mic quirks for Xiaomi Redmibook Air
ASoC: mediatek: mt8192: fix tdm out data is valid on rising edge
ALSA: dice: fix null pointer dereference when node is disconnected
ALSA: hda: generic: Fix the micmute led init state
ASoC: qcom: lpass-cpu: Fix lpass dai ids parse
spi: cadence: set cqspi to the driver_data field of struct device
ASoC: SOF: intel: fix wrong poll bits in dsp power down
ASoC: codecs: wcd934x: add a sanity check in set channel map
ASoC: qcom: sdm845: Fix array out of range on rx slim channels
ASoC: qcom: sdm845: Fix array out of bounds access
ASoC: remove remnants of sirf prima/atlas audio codec
...
|
|
The shifting of the u8 integer device by 24 bits to the left will
be promoted to a 32 bit signed int and then sign-extended to a
64 bit unsigned long. In the event that the top bit of device is
set then all then all the upper 32 bits of the unsigned long will
end up as also being set because of the sign-extension. Fix this
by casting device to an unsigned long before the shift.
Addresses-Coverity: ("Unintended sign extension")
Fixes: a07df82c7990 ("ALSA: usb-audio: Add DJM750 to Pioneer mixer quirk")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210318132008.15266-1-colin.king@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
MODULE_SUPPORTED_DEVICE was added in pre-git era and never was
implemented. We can safely remove it, because the kernel has grown
to have many more reliable mechanisms to determine if device is
supported or not.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The problem was in wrong "if" placement. chip->quirk_type is freed
in snd_card_free_when_closed(), but inside if statement it's accesed.
Fixes: 9799110825db ("ALSA: usb-audio: Disable USB autosuspend properly in setup_disable_autosuspend()")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/16da19126ff461e5e64a9aec648cce28fb8ed73e.1615242183.git.paskripkin@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
syzbot reported null pointer dereference in usb_audio_probe.
The problem was in case, when quirk == NULL. It's not an
error condition, so quirk must be checked before dereferencing.
Call Trace:
usb_probe_interface+0x315/0x7f0 drivers/usb/core/driver.c:396
really_probe+0x291/0xe60 drivers/base/dd.c:554
driver_probe_device+0x26b/0x3d0 drivers/base/dd.c:740
__device_attach_driver+0x1d1/0x290 drivers/base/dd.c:846
bus_for_each_drv+0x15f/0x1e0 drivers/base/bus.c:431
__device_attach+0x228/0x4a0 drivers/base/dd.c:914
bus_probe_device+0x1e4/0x290 drivers/base/bus.c:491
device_add+0xbdb/0x1db0 drivers/base/core.c:3242
usb_set_configuration+0x113f/0x1910 drivers/usb/core/message.c:2164
usb_generic_driver_probe+0xba/0x100 drivers/usb/core/generic.c:238
usb_probe_device+0xd9/0x2c0 drivers/usb/core/driver.c:293
really_probe+0x291/0xe60 drivers/base/dd.c:554
driver_probe_device+0x26b/0x3d0 drivers/base/dd.c:740
__device_attach_driver+0x1d1/0x290 drivers/base/dd.c:846
bus_for_each_drv+0x15f/0x1e0 drivers/base/bus.c:431
__device_attach+0x228/0x4a0 drivers/base/dd.c:914
bus_probe_device+0x1e4/0x290 drivers/base/bus.c:491
device_add+0xbdb/0x1db0 drivers/base/core.c:3242
usb_new_device.cold+0x721/0x1058 drivers/usb/core/hub.c:2555
hub_port_connect drivers/usb/core/hub.c:5223 [inline]
hub_port_connect_change drivers/usb/core/hub.c:5363 [inline]
port_event drivers/usb/core/hub.c:5509 [inline]
hub_event+0x2357/0x4320 drivers/usb/core/hub.c:5591
process_one_work+0x98d/0x1600 kernel/workqueue.c:2275
worker_thread+0x64c/0x1120 kernel/workqueue.c:2421
kthread+0x3b1/0x4a0 kernel/kthread.c:292
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:294
Reported-by: syzbot+719da9b149a931f5143f@syzkaller.appspotmail.com
Fixes: 9799110825db ("ALSA: usb-audio: Disable USB autosuspend properly in setup_disable_autosuspend()")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/f1ebad6e721412843bd1b12584444c0a63c6b2fb.1615242183.git.paskripkin@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Other Plantronics headset models seem requiring the same workaround as
C320-M to add the 20ms delay for the control messages, too. Apply the
workaround generically for devices with the vendor ID 0x047f.
Note that the problem didn't surface before 5.11 just with luck.
Since 5.11 got a big code rewrite about the stream handling, the
parameter setup procedure has changed, and this seemed triggering the
problem more often.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1182552
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210304085009.4770-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Dell AE515 sound bar (413c:a506) spews the error messages when the
driver tries to read the current sample frequency, hence it needs to
be on the list in snd_usb_get_sample_rate_quirk().
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=211551
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210304083021.2152-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Rear audio on Lenovo ThinkStation P620 stops working after commit
1965c4364bdd ("ALSA: usb-audio: Disable autosuspend for Lenovo
ThinkStation P620"):
[ 6.013526] usbcore: registered new interface driver snd-usb-audio
[ 6.023064] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x0, type = 1
[ 6.023083] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x202, wIndex = 0x0, type = 4
[ 6.023090] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x0, type = 1
[ 6.023098] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x202, wIndex = 0x0, type = 4
[ 6.023103] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x0, type = 1
[ 6.023110] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x202, wIndex = 0x0, type = 4
[ 6.045846] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x0, type = 1
[ 6.045866] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x202, wIndex = 0x0, type = 4
[ 6.045877] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x0, type = 1
[ 6.045886] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x202, wIndex = 0x0, type = 4
[ 6.045894] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x0, type = 1
[ 6.045908] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x202, wIndex = 0x0, type = 4
I overlooked the issue because when I was working on the said commit,
only the front audio is tested. Apology for that.
Changing supports_autosuspend in driver is too late for disabling
autosuspend, because it was already used by USB probe routine, so it can
break the balance on the following code that depends on
supports_autosuspend.
Fix it by using usb_disable_autosuspend() helper, and balance the
suspend count in disconnect callback.
Fixes: 1965c4364bdd ("ALSA: usb-audio: Disable autosuspend for Lenovo ThinkStation P620")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210304043419.287191-1-kai.heng.feng@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The microphone in the Plantronics C320-M headset will randomly
fail to initialize properly, at least when using Microsoft Teams.
Introducing a 20ms delay on the control messages appears to
resolve the issue.
Link: https://gitlab.freedesktop.org/pulseaudio/pulseaudio/-/issues/1065
Tested-by: Andreas Kempe <kempe@lysator.liu.se>
Signed-off-by: John Ernberg <john.ernberg@actia.se>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210303181405.39835-1-john.ernberg@actia.se
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Unlike the other DJM, the value to set the "CD/LINE" and "LINE" capture
control options are inverted. This fix makes sure that the displayed
info label while using `alsamixer` matches the input switches label
on the DJM-850 mixer.
Signed-off-by: Nicolas MURE <nicolas.mure2019@gmail.com>
Link: https://lore.kernel.org/r/20210301152729.18094-5-nicolas.mure2019@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Send an `URB_CONTROL out` USB frame to the device to configure its
samplerate. This should be done before using the device for audio
streaming (capture or playback).
See https://github.com/nm2107/Pioneer-DJM-850-driver-reverse-engineering/blob/172fb9a61055960c88c67b7c416fe5bf3609807b/doc/windows-dvs/framerate-setting/README.md
Signed-off-by: Nicolas MURE <nicolas.mure2019@gmail.com>
Link: https://lore.kernel.org/r/20210301152729.18094-4-nicolas.mure2019@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Declare audio capture controls to choose the audio source, and also to
set the capture level (in dB).
See https://github.com/nm2107/Pioneer-DJM-850-driver-reverse-engineering/blob/172fb9a61055960c88c67b7c416fe5bf3609807b/doc/windows-djm-850-setting-utility/mixer-output-tab/README.md
Signed-off-by: Nicolas MURE <nicolas.mure2019@gmail.com>
Link: https://lore.kernel.org/r/20210301152729.18094-3-nicolas.mure2019@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Declare the Pioneer DJM-850 interfaces for capture and playback.
See https://github.com/nm2107/Pioneer-DJM-850-driver-reverse-engineering/blob/172fb9a61055960c88c67b7c416fe5bf3609807b/doc/usb-device-specifications.md
for the complete device spec.
Signed-off-by: Nicolas MURE <nicolas.mure2019@gmail.com>
Link: https://lore.kernel.org/r/20210301152729.18094-2-nicolas.mure2019@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Back-merge of 5.12 devel branch for applying the further Pioneer DJM
patches.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
set samplerate
This commit only contains the fix about the `URB_CONTROL` request
direction to set the samplerate of Pioneer DJM devices (`URB_CONTROL out`).
Fixes: 3b85f5fc75d5 ("ALSA: usb-audio: Add DJM450 to Pioneer format quirk")
Signed-off-by: Nicolas MURE <nicolas.mure2019@gmail.com>
Link: https://lore.kernel.org/r/20210301142927.14552-1-nicolas.mure2019@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The Corsair Virtuoso SE RGB Wireless is a USB headset with a mic and a
sidetone feature. Assign the Corsair Virtuoso name map to the SE product
ids as well, in order to label its mixer appropriately and allow
userspace to pick the correct volume controls.
Signed-off-by: Andrea Fagiani <andfagiani@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/40bbdf55-f854-e2ee-87b4-183e6451352c@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
A number of devices have named substreams which are hard to remember /
decypher from <device> MIDI n names. Eg. Korg puts a pass through on
one substream and iConnectivity devices name the connections.
This makes it easier to connect to the correct device. Devices which
handle naming through quirks are unaffected by this change.
Addresses TODO comment in sound/usb/midi.c
Signed-off-by: George Harker <george@george-graphics.co.uk>
Link: https://lore.kernel.org/r/20210226212617.24616-1-george@george-graphics.co.uk
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Use struct definitions from linux/usb/midi.h rather than locally
define the structs in sound/usb/midi.c.
Signed-off-by: George Harker <george@george-graphics.co.uk>
Link: https://lore.kernel.org/r/20210226212457.24538-1-george@george-graphics.co.uk
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The recent fix for the hw constraints for implicit feedback streams
via commit e4ea77f8e53f ("ALSA: usb-audio: Always apply the hw
constraints for implicit fb sync") added the check of the matching
endpoints and whether those EPs are already opened. This is needed
and correct, per se, even for the normal streams without the implicit
feedback, as the endpoint setup is exclusive.
However, it's reported that there seem applications that behave in
unexpected ways to update the hw_params without clearing the previous
setup via hw_free, and those hit a problem now: then hw_params is
called with still the previous EP setup kept, hence it's restricted
with the previous own setup. Although the obvious fix is to call
snd_pcm_hw_free() API in the application side, it's a kind of
unwelcome change.
This patch tries to ease the situation: in the endpoint check, we add
a couple of more conditions and now skip the endpoint that is being
used only by the stream in question itself. That is, in addition to
the presence check of ep (ep->cur_audiofmt is non-NULL), when the
following conditions are met, we skip such an ep:
- ep->opened == 1, and
- ep->cur_audiofmt == subs->cur_audiofmt.
subs->cur_audiofmt is non-NULL only if it's a re-setup of hw_params,
and ep->cur_audiofmt points to the currently set up parameters. So if
those match, it must be this stream itself.
Fixes: e4ea77f8e53f ("ALSA: usb-audio: Always apply the hw constraints for implicit fb sync")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=211941
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210228080138.9936-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Some USB audio firmware seem to report broken dB values for the volume
controls, and this screws up applications like PulseAudio who blindly
trusts the given data. For example, Edifier G2000 reports a PCM
volume from -128dB to -127dB, and this results in barely inaudible
sound.
This patch adds a sort of sanity check at parsing the dB values in
USB-audio driver and disables the dB reporting if the range looks
bogus. Here, we assume -96dB as the bottom line of the max dB.
Note that, if one can figure out that proper dB range later, it can be
patched in the mixer maps.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=211929
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210227105737.3656-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The commit 93db51d06b32 ("ALSA: usb-audio: Check valid altsetting at
parsing rates for UAC2/3") changed the behavior of the function
set_sample_rate_v2v3() slightly to treat the inconsistent sample rate
as an error. It was done by assumption that the sample rate
validation should have been done at the parser phase as implemented in
that patch. But the validation is later selectively enabled only for
certain devices as it causes a regression (the commit fe773b8711e3
"ALSA: usb-audio: workaround for iface reset issue"), and now the
inconsistency surfaced as a fatal error while it worked in the past as
is, as reported for FiiO M3K DAC.
For recovering from the regression, change set_sample_rate_v2v3()
again to ignore the sample rate difference as non-error.
BugLink: https://bugzilla.opensuse.org/show_bug.cgi?id=1182633
Fixes: 93db51d06b32 ("ALSA: usb-audio: Check valid altsetting at parsing rates for UAC2/3")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210227082002.21185-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
BOSS GP-10 with 0582:0185 requires the similar quirk to make the
implicit feedback working like other BOSS devices.
Reported-by: Keith Milner <kamilner@superlative.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210214154251.10750-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In the later patch, we're going to issue the PCM sync_stop calls at
disconnection. But currently the USB-audio driver can't handle it
because it has a check of shutdown flag for stopping the URBs. This
is basically superfluous (the stopping URBs are safe at disconnection
state), so let's drop the check.
Fixes: dc5eafe7787c ("ALSA: usb-audio: Support PCM sync_stop")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210206203052.15606-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The endpoint management has bit flags to indicate the current state,
and we're dealing two things: the running bit and the stopping bit.
There is a thin window in transition from the running to the stopping
in stop_urbs(), and as long as the bit flags are used, it's difficult
to plug.
This patch modifies the state management code to use the atomic int
and follow the explicit three states, STOPPED, RUNNING and STOPPING.
The state change is done via atomic_cmpxhg() for avoiding possible
races, and check the state change more strictly. The unexpected state
change is now handled as an error.
Fixes: d0f09d1e4a88 ("ALSA: usb-audio: Refactoring endpoint URB deactivation")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210206203052.15606-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When we stop an endpoint in release_urbs(), it ignores the
inconsistent endpoint state and tries to release the resources.
This shouldn't happen in theory, but it's still safer to abort the
release and let the caller proper error handling.
Also, stop_and_unlink_urbs() called from release_urbs() does two step
works, and it's more straightforward to split this to two functions
again, so that the call from the PCM trigger won't take the path with
sleeping.
This patch modifies the EP management code to adapt two points above.
Fixes: d0f09d1e4a88 ("ALSA: usb-audio: Refactoring endpoint URB deactivation")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210206203052.15606-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This commit adds mixer quirks for the Pioneer DJM-900NXS2 mixer. This
device has 6 capture channels, 5 of them allow setting the signal
source. This adds controls for these, similar to the DJM-250Mk2.
However, playpack channels are not controllable via software like on the
250Mk2, as they can only be set manually on the mixing console.
Read-only controls showing the currently selected playback channels are
omitted.
Signed-off-by: Fabian Lesniak <fabian@lesniak-it.de>
Link: https://lore.kernel.org/r/20210205215116.258724-2-fabian@lesniak-it.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This allows for N different devices to use the pioneer mixer quirk for
setting capture/record type and recording level. The impementation has
not changed much with the exception of an additional mask on
private_value to allow storing of a device index:
DEVICE MASK 0xff000000
GROUP_MASK 0x00ff0000
VALUE_MASK 0x0000ffff
This could be improved by changing the arrays of wValues for each
channel to contain named definitions (e.g. SND_DJM_CAP_LINE). It would
improve readability and perhaps would allow using the same array for
multiple channels. The channel number can be specified on the control
next to the wIndex.
Feedback is very much appreciated as I'm not the most proficient C
programmer but am learning as I go.
Signed-off-by: Olivia Mackintosh <livvy@base.nu>
Link: https://lore.kernel.org/r/20210205184256.10201-2-livvy@base.nu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The commit f274baa49be6 ("ALSA: usb-audio: Allow non-vmalloc buffer
for PCM buffers") introduced the mode to allocate coherent pages for
PCM buffers, and it used bus->controller device as its DMA device.
It turned out, however, that bus->sysdev is a more appropriate device
to be used for DMA mapping in HCD code.
This patch corrects the device reference accordingly.
Note that, on most platforms, both point to the very same device,
hence this patch doesn't change anything practically. But on
platforms like xhcd-plat hcd, the change becomes effective.
Fixes: f274baa49be6 ("ALSA: usb-audio: Allow non-vmalloc buffer for PCM buffers")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210205144559.29555-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The kerndoc comment for the new function snd_usb_endpoint_free_all()
had a typo wrt the argument name. Fix it.
Fixes: 00272c61827e ("ALSA: usb-audio: Avoid unnecessary interface re-setup")
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210205082837.6327-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Back-merge the 5.11 devel branch for further patching.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
As with most Pioneer devices, the device descriptor is vendor specific
and as such, the number of channels, the PCM format, endpoints and
sample rate need to be specified. This device has 8 inputs and 8 outputs
and a sample rate of 48000 only. The PCM format is S24_3LE like other
devices.
There seems to be an appetite for reducing duplication amongs these
Pioneer patches but again, I feel this is a step to be taken after
support has been added as it's not completely clear where the
commonalities are.
Signed-off-by: Olivia Mackintosh <livvy@base.nu>
Link: https://lore.kernel.org/r/20210202134225.3217-3-livvy@base.nu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Like the DJM-750, ensure that the format control message is passed to
the device when opening a stream. It seems as though fmt->sync_ep is not
always set when this function is called hence the passing of the value
at the call site. If this can be fixed, fmt->sync_up should be used as
the wvalue.
There doesn't seem to be a "cpu_to_le24" type function defined hence for
the open code but I did see a similar thing done in Bluez lib. Perhaps
we can get these definitions defined in byteorder.h. See hci_cpu_to_le24
in include/net/bluetooth/hci.h:2543 for similar usage.
Signed-off-by: Olivia Mackintosh <livvy@base.nu>
Link: https://lore.kernel.org/r/20210202134225.3217-2-livvy@base.nu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
