| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
'asoc/fix/rcar', 'asoc/fix/tlv320aic31xx' and 'asoc/fix/tlv320aic3x' into asoc-linus
|
|
'asoc/fix/cs42l73' and 'asoc/fix/fsl-spdif' into asoc-linus
|
|
Commit 0406a40a0 ("ASoC: jz4740: Use the generic dmaengine PCM driver")
jz4740-pcm.c file, but neglected to remove the Makefile entries.
Fixes: 0406a40a0 ("ASoC: jz4740: Use the generic dmaengine PCM driver")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reported-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
There were occasional ADSP crash during reboot testing:
[ 11.883364] BUG: unable to handle kernel paging request at ffffc90121700000
[ 11.883380] IP: [<ffffffffc024d8bc>] sst_module_insert_fixed_block+0x24f/0x26d [snd_soc_sst_dsp]
[ 11.883397] PGD 7800b067 PUD 0
[ 11.883405] Oops: 0002 [#1] SMP
[ 11.886418] gsmi: Log Shutdown Reason 0x03
The virtual address, ffffc90121700000, was out of range. The virtual
address is calculated by adding LPE base address with an offset:
sst_memcpy32(dsp->addr.lpe + data->offset, data->data, data->size);
The offset is calculated in sst_byt_parse_module, by subtraction of
two virtual addresses dsp->addr.fw_ext and dsp->addr.lpe:
block_data.offset = block->ram_offset + (dsp->addr.fw_ext - dsp->addr.lpe);
These virtual addresses are assigned by kernel from ioremap:
sst->addr.lpe = ioremap(pdata->lpe_base, pdata->lpe_size);
sst->addr.fw_ext = ioremap(pdata->fw_base, pdata->fw_size);
In current driver code, offset is defined as unsigned int32:
struct sst_module_data {
...
u32 offset; /* offset in FW file */
};
Most of the time kernel assigned virtual addresses with addr.fw_ext
greater than addr.lpe. But sometimes it was the other way round.
Fix the problem by declaring offset as signed int32_t.
Signed-off-by: Wenkai Du <wenkai.du@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Commit 9e1fda4ae158 ("ASoC: dapm: Implement mixer input auto-disable")
is trying to free the widget it allocated by snd_soc_dapm_new_control()
call in dapm_kcontrol_data_alloc() by adding kfree(data->widget) to
dapm_kcontrol_free().
This is causing a widget double free with auto-disabled DAPM kcontrols
in sound card unregistration because widgets are already freed before
dapm_kcontrol_free() is called.
Reason for that is all widgets are added into dapm->card->widgets list
in snd_soc_dapm_new_control() and freed in dapm_free_widgets() during
execution of snd_soc_dapm_free().
Now snd_soc_dapm_free() calls for different DAPM contexts happens before
snd_card_free() call from where the call chain to dapm_kcontrol_free()
begins:
soc_cleanup_card_resources()
soc_remove_dai_links()
soc_remove_link_dais()
snd_soc_dapm_free(&cpu_dai->dapm)
soc_remove_link_components()
soc_remove_platform()
snd_soc_dapm_free(&platform->dapm)
soc_remove_codec()
snd_soc_dapm_free(&codec->dapm)
snd_soc_dapm_free(&card->dapm)
snd_card_free()
snd_card_do_free()
snd_device_free_all()
snd_device_free()
snd_ctl_dev_free()
snd_ctl_remove()
snd_ctl_free_one()
dapm_kcontrol_free()
This wasn't making harm with ordinary DAPM kcontrols since data->widget is NULL for
them.
Fixes: 9e1fda4ae158 (ASoC: dapm: Implement mixer input auto-disable)
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
|
|
Fix an incorrect sizeof() usage in sst_hsw_stream_get_volume(). sst_dsp_read()
is called to read into a variable of type u32, but is passed sizeof(u32 *) for
argument 'size_t bytes'. Detected by Coverity: CID 1195260.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The intent was to say "sizeof(*pos)" and not "sizeof(pos)".
The sizeof(*pos) is 8 bytes so the bug won't show up on 64 bit systems.
The sizeof(*dx) is 172 bytes so that will be a bugfix.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Current code missed a gpio_free() call in cs42l73_i2c_remove().
Convert to use devm_gpio_request_one() to fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Current code missed a gpio_free() call in cs42l52_i2c_remove().
Convert to use devm_gpio_request_one() to fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
It should use STC_SYSCLK_DIV_OFFSET. Thus fix it.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Commit 0cd257bf9b9b0cbb4fa1a5c988a232506997867c, "ASoC: alc5623:
Convert to direct regmap API usage" broke probing of the codec,
because of wrong endinness of the ID and codec version read from the
device. Fix this by removing the existing flipping of the endiannes,
and extracting the codec type byte from the word from the regmap.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Currently the second tlv320aic3x instance fails to
be probed from DT if the reset pin is shared with
the first one.
This patch fixes it by moving the list add of the
reset pin into the i2c_probe method.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
As with the previous commit, before a clock can be used it must be prepared
for use. Change from clk_enable() and clk_disable() to the versions of the
calls which also prepare and un-prepare the clocks.
Will fix warnings from the clock code when this is used.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here is a bunch of small fixes that have been collected since the
previous pull request. In addition to various misc fixes, the
following are included:
- HD-audio quirks for Dell, HP, Chromebook, and ALC28x codecs
- HD-audio AMD HDMI regression fix
- Continued PM support/fixes for ice1712 driver
- Multiplatform fixes for ASoC samsung drivers
- Addition of device id tables to a few ASoC drivers
- Bit clock polarity config and error flag fixes in ASoC fsl_sai"
* tag 'sound-fix-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (32 commits)
ALSA: usb-audio: Suppress repetitive debug messages from retire_playback_urb()
ALSA: hda - Make full_reset boolean
ALSA: hda - add headset mic detect quirk for a Dell laptop
sound: dmasound: use module_platform_driver_probe()
ALSA: au1x00: use module_platform_driver()
ALSA: hda - Use runtime helper to check active state.
ALSA: ice1712: Fix boundary checks in PCM pointer ops
ASoC: davinci-mcasp: Fix bit clock polarity settings
ASoC: samsung: Fix build on multiplatform
ASoC: fsl_sai: Fix Bit Clock Polarity configurations
ALSA: hda - Do not assign streams in reverse order
ALSA: hda/realtek - Add eapd shutup to ALC283
ALSA: hda/realtek - Change model name alias for ChromeOS
ASoC: da732x: Print correct major id
ALSA: hda/realtek - Improve HP depop when system change power state on Chromebook
ASoC: cs42l52: Fix mask for REVID
sound/oss: Remove uncompilable DBG macro use
ALSA: ice1712: Save/restore routing and rate registers
ALSA: ice1712: restore AK4xxx volumes on resume
ASoC: alc56(23|32): fix undefined return value of probing code
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.15
A smattering of device specific fixes, nothing stands out here except
for the multiplatform fixes for Samsung and the device IDs being added
by Stephen Warren - there's no real code changes from those and they
give better robustness to the enumeration with DT.
|
|
'asoc/fix/tlv320aic23' and 'asoc/fix/warn' into asoc-linus
|
|
'asoc/fix/cs42xxx8', 'asoc/fix/da732x', 'asoc/fix/davinci', 'asoc/fix/fsl-sai', 'asoc/fix/fsl-ssi' and 'asoc/fix/max98090' into asoc-linus
|
|
IB_NF, NB_IF and IB_IF configured the bc polarity incorrectly. The receive
polarity was set to the same edge as the TX in these cases.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
PCM and S/PDIF drivers referenced mach headers for a trivial
data structure. This caused build errors on multiplatform builds
as machine headers are not accessible from driver files. Move the data
structure definition to the driver header and remove the dependency.
While at it rename the structure to avoid multiple definition errors
as the same structure is also used by the platform code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The BCP bit in TCR4/RCR4 register rules as followings:
0 Bit clock is active high with drive outputs on rising edge
and sample inputs on falling edge.
1 Bit clock is active low with drive outputs on falling edge
and sample inputs on rising edge.
For all formats currently supported in the fsl_sai driver, they're exactly
sending data on the falling edge and sampling on the rising edge.
However, the driver clears this BCP bit for all of them which results click
noise when working with SGTL5000 and big noise with WM8962.
Thus this patch corrects the BCP settings for all the formats here to fix
the nosie issue.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Acked-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
DA732X_ID_MAJOR_MASK is 0xF0, so the major id is
(reg & DA732X_ID_MAJOR_MASK) >> 4.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
BIT[0:2] of register 01h is REVID, so the mask for REVID should be 0x7.
Also updates the code to use CS42L52_CHIP_REV_MASK.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Arnd Bergmann:
"These changes are mostly for ARM specific device drivers that either
don't have an upstream maintainer, or that had the maintainer ask us
to pick up the changes to avoid conflicts.
A large chunk of this are clock drivers (bcm281xx, exynos, versatile,
shmobile), aside from that, reset controllers for STi as well as a
large rework of the Marvell Orion/EBU watchdog driver are notable"
* tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
Revert "dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac."
Revert "net: stmmac: Add SOCFPGA glue driver"
ARM: shmobile: r8a7791: Fix SCIFA3-5 clocks
ARM: STi: Add reset controller support to mach-sti Kconfig
drivers: reset: stih416: add softreset controller
drivers: reset: stih415: add softreset controller
drivers: reset: Reset controller driver for STiH416
drivers: reset: Reset controller driver for STiH415
drivers: reset: STi SoC system configuration reset controller support
dts: socfpga: Add sysmgr node so the gmac can use to reference
dts: socfpga: Add support for SD/MMC on the SOCFPGA platform
reset: Add optional resets and stubs
ARM: shmobile: r7s72100: fix bus clock calculation
Power: Reset: Generalize qnap-poweroff to work on Synology devices.
dts: socfpga: Update clock entry to support multiple parents
ARM: socfpga: Update socfpga_defconfig
dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
net: stmmac: Add SOCFPGA glue driver
watchdog: orion_wdt: Use %pa to print 'phys_addr_t'
drivers: cci: Export CCI PMU revision
...
|
|
Commit 5d6be5aa ("ASoC: codec: Simplify ASoC probe code.") left variable
'ret', whose value is returned, uninitialized. Since it is not used
otherwise, remove it.
Signed-off-by: Christoph Jaeger <christophjaeger@linux.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Fix checking return value of regmap_read().
Also fix reporting the chip_id value. CS42XX8_CHIPID_CHIP_ID_MASK is 0xF0,
so the chip_id value is (val & CS42XX8_CHIPID_CHIP_ID_MASK) >> 4).
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Paul Handrigan <paul.handrigan@cirrus.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Acked-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Add a device tree match table. This serves to make the driver's support
of device tree more explicit. Perhaps the fallback for DT matching to
using the i2c_device_id table will go away one day, since it fails in
face of devices from different vendors with the same name.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Add a device tree match table. This serves to make the driver's support
of device tree more explicit. Perhaps the fallback for DT matching to
using the i2c_device_id table will go away one day, since it fails in
face of devices from different vendors with the same name.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Add a device tree match table. This serves to make the driver's support
of device tree more explicit. Perhaps the fallback for DT matching to
using the i2c_device_id table will go away one day, since it fails in
face of devices from different vendors with the same name.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
alc5632_probe() returns ret, yet it is not initialized or set anywhere.
This ends up causing the function to appear to fail, and audio not to
work on the Toshiba AC100, with my compiler at least.
This function used to set ret in all cases, but recent cleanup removed
that.
Fixes: 5d6be5aa6bec ("ASoC: codec: Simplify ASoC probe code.")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Add a device tree match table. This serves to make the driver's support
of device tree more explicit. Perhaps the fallback for DT matching to
using the i2c_device_id table will go away one day, since it fails in
face of devices from different vendors with the same name.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Final updates for v3.15 merge window
A few more updates from last week - use of the tdm_slot mapping from
Xiubo plus a few smaller fixes and cleanups.
|
|
It's quite cricial to clear error flags because SAI might hang if getting
FIFO underrun during playback (I haven't confirmed the same issue on Rx
overflow though).
So this patch enables those irq and adds isr() to clear the flags so as to
keep playback entirely safe.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
asoc-next
|
|
|
|
into asoc-next
|
|
On Tegra the convention is to have a single machine driver
that's controlling the whole audio subsystem.
Move the clock handling to the machine driver, to be in line
with the other Tegra drivers and give the machine driver
full control over the single Tegra audio PLL.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Some simple audio cards may have many DAI links.
This patch extends the simple-card driver for handling such cards.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The DAI link array and the properties (fmt, sysclk slots) are
hard-coded for a single CPU / CODEC link.
This patch dynamically allocates the DAI link array and the
properties with the aim of supporting many DAI links.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
This patch add .xlate_tdm_slot_mask support for IMX SSI, and this
will generate the TDM slot TX and RX masks.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
This patch add .xlate_tdm_slot_mask support for ESAI, and this will
generate the TDM slot TX and RX masks.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
This patch add fsl_asoc_xlate_tdm_slot_mask() support for utils.
For the some spcified DAI driver, this will be used to generate the
TDM slot TX/RX mask. And the TX/RX mask will use a 0 bit for an active
slot as default, and the default active bits are at the LSB of
the masks.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The 'of_' is not appropriate here for there hasn't any DT parsing.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Before we had card level support for DAPM and controls machine drivers would
register their controls and DAPM elements with the CODEC. This required us to
temporarily unset the name_prefix of a CODEC during the rtd init callback to
avoid the machine level controls getting the CODEC's prefix. Now that all
machine drivers properly register their machine level controls and DAPM elements
with the card rather than with the CODEC we can drop the hack that sets the
CODEC's name_prefix to NULL while calling the DAI link or AUX dev init callback.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
|
|
src might not exist.
kernel will be hung-up without this patch in such case.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v3.15
A few more updates for the merge window:
- Fixes for the simple-card DAI format DT mess.
- A new driver for Cirrus cs42xx8 devices.
- DT support for a couple more devices.
- A revert of a previous buggy fix for soc-pcm, plus a few more fixes
and cleanups.
|
|
into asoc-next
|
|
|
|
into asoc-next
|
|
'asoc/topic/kirkwood' into asoc-next
|
