summaryrefslogtreecommitdiffstats
path: root/sound/soc
AgeCommit message (Collapse)AuthorFilesLines
2018-11-28ASoC: dmic: introduce mode switch delayJenny TC1-0/+35
On startup, applications such as PulseAudio or CRAS enable playback or capture on all PCM devices to verify that configurations are correct, and close them immediately. For DMICs, this can result in the clock being turned off very quickly, which may not compatible with internal state machine transition requirements. This patch add a mode-switch delay which will prevent the clock from being turned off without complying with manufacturer timing specifications. While the DMIC clock may be controlled at a lower level, be it with hardware or firmware, applying the delay during the STOP_TRIGGER phase ensures that there is no race condition, e.g. with the hardware/firmware turning off the clock earlier Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com> Signed-off-by: Jairaj Arava <jairaj.arava@intel.com> Signed-off-by: Harsha Priya <harshapriya.n@intel.com> Signed-off-by: Jenny TC <jenny.tc@intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-28ASoC: qcom: sdm845: Create and setup jack in init callbackCheng-Yi Chiang1-2/+55
Add a callback for init ops on dai_link to create and setup jack. Signed-off-by: Rohit kumar <rohitkr@codeaurora.org> Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org> Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-28ASoC: qcom: sdm845: Add board specific dapm widgetsCheng-Yi Chiang1-0/+10
Add board specific dapm widgets so these widgets can be used in the route. Signed-off-by: Rohit kumar <rohitkr@codeaurora.org> Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org> Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-28ASoC: davinci-mcasp: Implement configurable dismod handlingPeter Ujfalusi2-1/+19
If the dismod is specified in the DT node, use the specified custom value to configure the drive on state of the inactive TX slots. If the dismod is not present or booted in legacy mode, the dismod is set to low as it was the original behavior. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-28ASoC: davinci-mcasp: Update PDIR (pin direction) register handlingPeter Ujfalusi2-32/+85
When McASP is master and the PDIR for the clock pins are configured as outputs before the clocking is configured it will output whatever clock is generated at the moment internally. The clock will switch to the correct rate only when the we start the clock generators. To avoid this we must only set the pin as output after the clock is configured and enabled. AXR pins configured as outputs behaves somehow interesting as well: when McASP is not enabled and the pin is selected as output it will not honor the DISMOD settings for the inactive state, but will pull the pin down. Add a new bitfield and mark the pins there which needs to be output and set the pins only at the time when they will behave correctly. On stream stop configure the pins back to input which makes them to obey the global pin configuration regarding to pull up/down. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-28ASoC: davinci-mcasp: Clear TXSTAT register before activating serializersPeter Ujfalusi1-0/+2
Follow the guideline from the TRM: Before starting, clear the respective transmitter and receiver status registers To avoid stale state stored in the status registers. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-28ASoC: Intel: Skylake: Add FW reply for MCLK/SCLK IPCSubhransu S. Prusty1-0/+6
If mclk/sclk is already running, FW responds with IPC reply MCLK/SCLK already running. Add these to the IPC reply lookup table. Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com> Signed-off-by: Sriram Periyasamy <sriramx.periyasamy@intel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-28ASoC: Intel: Skylake: Make DSP replies more human readableSubhransu S. Prusty1-11/+33
Add more meaning to the IPC replies for easy debugging. Replace the switch case with a lookup table to lookup for the IPC replies and print in human readable form. Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com> Signed-off-by: Sriram Periyasamy <sriramx.periyasamy@intel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-26ASoC: max9867: Fix whitespaceLadislav Michl1-7/+5
Minor changes to match coding style. Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-26ASoC: amd: Fix a NULL vs IS_ERR() check in probeDan Carpenter1-2/+2
The platform_device_register_full() function doesn't return NULL, it returns error pointers. Fixes: 7894a7e7ea3d ("ASoC: amd: create ACP3x PCM platform device") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-23ASoC: audio-graph-card: tidyup define positionKuninori Morimoto1-5/+5
commit f986907c9225 ("ASoC: audio-graph-card: add widgets and routing for external amplifier support") added new function asoc_graph_card_outdrv_event(), but the inserted position breaks define area. This patch tidyup it Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-23ASoC: audio-graph-card: tidyup typo SND_AUDIO_GRAPH_CARDKuninori Morimoto1-1/+1
1 "simple" is enough on Kconfig help Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-23ASoC: audio-graph-scu-card: tidyup asoc_simple_card_parse_daifmt() timingKuninori Morimoto1-38/+16
Current audio-graph-scu-card driver is parsing codec position for DPCM and consider DAI format. But, current operation is doing totally pointless, because 1) asoc_simple_card_parse_daifmt() will be called not only for 1st codec on current implementation, and it will be used as fixed format 2) it should be called for each CPU/Codec pair. Let's tidyup asoc_simple_card_parse_daifmt() timing. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-23ASoC: audio-graph-scu-card: tidyup "convert-rate/channels" parsingKuninori Morimoto1-0/+7
audio-graph-scu-card.c is supporting "convert-rate/channels" which is used for DPCM. But, sound card might have multi codecs, and each codec might need each convert-rate/channels. This patch supports each codec's convert-rate/channles support. top node convert-rate/channels will overwrite settings if exist. It can't support each codec's convert-rate/channels if sound card had multi codecs without this patch. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-23ASoC: audio-graph-scu-card: tidyup "prefix" parsingKuninori Morimoto1-0/+10
audio-graph-scu-card.c is supporting "prefix" which is used to avoid DAI naming conflict when CPU/Codec matching. But, sound card might have multi sub-devices, and each codec might need each prefix. Now, ASoC is supporting snd_soc_of_parse_node_prefix(), let's support it on audio-graph-scu-card, too. It is keeping existing DT style. It can't support each codec's prefix if sound card had multi sub-devices without this patch. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-23ASoC: simple-scu-card: tidyup "prefix" parsingKuninori Morimoto1-0/+7
simple-scu-card.c is supporting "prefix" which is used to avoid DAI naming conflict when CPU/Codec matching. But, sound card might have multi sub-devices, and each codec might need each prefix. Now, ASoC is supporting snd_soc_of_parse_node_prefix(), let's support it on audio-graph-scu-card, too. It is keeping existing DT style. It can't support each codec's prefix if sound card had multi sub-devices without this patch. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-23ASoC: soc-core: add snd_soc_of_parse_node_prefix()Kuninori Morimoto1-6/+5
Current ASoC has snd_soc_of_parse_audio_prefix() to get codec_conf settings from DT which is used to avoid DAI naming conflict when CPU/Codec matching. Currently, it is parsing from "top node", but, we want to parse from "each sub node" if sound card had multi cpus/codecs. This patch adds new snd_soc_of_parse_node_prefix() to allow parsing settings from selected node. It is keeping existing snd_soc_of_parse_audio_prefix() by using macro. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-23ASoC: simple-amplifier: add VCC regulator widgetVasily Khoruzhick1-0/+4
Amplifier may have assosicated regulator, so add a widget for it and appropriate route. Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com> Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-23ASoC: sunxi: sun50i-codec-analog: Add support for cpvdd regulator supplyChen-Yu Tsai1-0/+2
On the Allwinner A64 SoCs, the audio codec has a built-in headphone amplifier. This amplifier has a power supply separate from the rest of the analog audio circuitry, labeled cpvdd. This patch adds a DAPM widget for this supply, and ties it to the headphone amp widget. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-21ASoC: simple_card_utils: remove "option" from ↵Kuninori Morimoto5-11/+7
asoc_simple_card_of_parse_routing() asoc_simple_card_of_parse_routing() had "option" parameter to consider error handling, but it is very pointless parameter. Let's remove it. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-21ASoC: simple-card-utils: tidyup asoc_simple_card_parse_convert()Kuninori Morimoto3-4/+5
Current simple-card-utils has asoc_simple_card_parse_convert() to parse convert channel/rate for be_hw_params_fixup. But, it is parsing from top of node. If sound card had multi subnode, we need to parse it from each sub node. This patch tidyup asoc_simple_card_parse_convert() to allow parsing settings from each node. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-21ASoC: simple-card-utils: accept NULL parameter on asoc_simple_card_xxx()Kuninori Morimoto1-2/+9
If simple-card-utils accept NULL pointer on asoc_simple_card_xxx(), each driver code will be more simple. Let's accept NULL pointer. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-21ASoC: simple-card-utils: remove asoc_simple_card_clk_register()Kuninori Morimoto1-7/+1
asoc_simple_card_clk_register() is used but only 1 user, and very pointless code. Let's remove it. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-21ASoC: rsnd: makes rsnd_ssi_is_dma_mode() staticKuninori Morimoto2-3/+3
ssi.c only is using rsnd_ssi_is_dma_mode(). Let's move it as static function. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-21ASoC: rsnd: tidyup rsnd_parse_connect_ssiu_compatible()Kuninori Morimoto1-2/+4
rsnd_parse_connect_ssiu_compatible() is doing - using rsnd_ssiu_id(), but we use it via rsnd_mod_id() - we can break loop if rsnd_dai_connect() was called This patch fixup these. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-21ASoC: sdm845: Add support for Secondary MI2S interfaceRohit kumar1-0/+18
Add support to configure bit clock for secondary MI2S TX interface. Signed-off-by: Rohit kumar <rohitkr@codeaurora.org> Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-21ASoC: sdm845: Update slot_width for Quaternary TDM portRohit kumar1-4/+5
Change slot_width for quaternary TDM port to 16 and update bclk rate for TDM and MI2S interfaces accordingly. Signed-off-by: Rohit kumar <rohitkr@codeaurora.org> Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-20ASoC: Intel: use platform_data for machine driversPierre-Louis Bossart6-8/+15
For some reason we have different mechanisms for passing data to machine drivers. Use the solution used by Atom/SST and SOF instead of using drv_data as done by Skylake. Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-20ASoC: Intel: fix interface for Chromebook machine driversPierre-Louis Bossart6-24/+21
The changes for HDaudio overlooked the fact that the machine drivers used for Chromebooks rely on the dmic number information passed as pdata. Add dmic_num field to standard interface and use standard interface instead of SKL-specific one. Also clean-up pdata definition to remove fields that are no longer used. Fixes: 842bb5135f10 ('ASoC: Intel: use standard interface for Hdaudio machine driver') Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-20ASoC: tlv320aic3x: Add support for CBM_CFS and CBS_CFM clocking modesPeter Ujfalusi1-0/+10
The codec can support any variation of bclk/fs master/slave configuration. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-16ASoC: rt5663: Fix error handling of regulator_set_loadCheng-Yi Chiang1-9/+12
The default implementation of regulator_set_load returns REGULATOR_MODE_NORMAL, which is positive. [This was a bug which is being fixed but the change is valid anyway -- bronie] rt5663_i2c_probe should only do error handling when return value of regulator_set_load is negative. In this case, rt5663_i2c_probe should return error. Also, consolidate err_irq into err_enable. Fix the missing goto for temporary regmap and rt5663->regmap. Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-16ASoC: amd: fix spelling mistake "Inavlid" -> "Invalid"Colin Ian King1-1/+1
There is a spelling mistake in a dev_err message. Fix this. Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-16ASoC: qcom: clean up indentation, remove extraneous tabColin Ian King1-1/+1
The return statement is indented too much by one level, fix this by removing the extraneous tab. Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-16ASoC: arizona: fix indentation issue with return statementColin Ian King1-1/+1
The return statement is indented incorrectly. Fix this by adding in the missing tab. Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-16ASoC: tlv320dac33: clean up indentation, remove extraneous tabColin Ian King1-1/+1
The goto statement is indented too much by one level, fix this by removing the extraneous tab. Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-16ASoC: tlv320aic31xx: asihpi: clean up indentation, remove extraneous tabColin Ian King1-1/+1
The return statement is indented too much by one level, fix this by removing an extraneous tab. Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-16ASoC: Convert a few more users to using %pOFn instead of device_node.nameRob Herring3-6/+6
In preparation to remove the node name pointer from struct device_node, convert printf users to use the %pOFn format specifier. Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Cc: Olivier Moysan <olivier.moysan@st.com> Cc: Arnaud Pouliquen <arnaud.pouliquen@st.com> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: alsa-devel@alsa-project.org Cc: linux-stm32@st-md-mailman.stormreply.com Cc: linux-arm-kernel@lists.infradead.org Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-15ASoC: rt5663: Add regulator supportCheng-Yi Chiang1-7/+61
Add regulator support to turn on cpvdd and avdd in probe. If a regulator is not given from device tree, a dummy regulator will be used. Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-15ASoC: ak4118: Add support for AK4118 S/PDIF transceiverAdrien Charruel3-0/+446
The AK4118A is a digital audio transceiver supporting 8 input channels at 192kHz and with 24bits resolution. It converts the S/PDIF signal to I2S format and is configurable over I2C. This driver introduce a minimal support of the AK4118, like selecting the input channel, reading input frequency and detecting some errors. Datasheet is available here: https://www.akm.com/akm/en/file/datasheet/AK4118AEQ.pdf Signed-off-by: Adrien Charruel <adrien.charruel@devialet.com> Signed-off-by: Clément Péron <peron.clem@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-15ASoC: amd: remove set but not used variable 'dma_buffer'YueHaibing1-2/+0
Fixes gcc '-Wunused-but-set-variable' warning: sound/soc/amd/raven/acp3x-pcm-dma.c: In function 'acp3x_dma_hw_params': sound/soc/amd/raven/acp3x-pcm-dma.c:333:25: warning: variable 'dma_buffer' set but not used [-Wunused-but-set-variable] It never used since introduction in commit 8de1b5ed0337 ("ASoC: amd: add acp3x system resume pm op") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-15ASoC: amd: Switch to SPDX identifierVijendar Mukunda5-47/+22
Adopt the SPDX license identifier headers to ease license compliance management. Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Vijendar Mukunda <vijendar.mukunda@amd.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-15ASoC: amd: Fixed build errorsVijendar Mukunda1-0/+1
Fixed build errors. - Implicit declaration of pci_enable_msi() & pci_disable_msi() api's for openrisc architecture. - type defaults to 'int' in declaration of 'module_pci_driver' Enabled build for x86 architecture. Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Vijendar Mukunda <vijendar.mukunda@amd.com> Tested-by: Ravulapati Vishnu vardhan Rao <Vishnuvardhanrao.Ravulapati@amd.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-15ASoC: nau8822: convert to SPDX identifiersDavid Lin1-1/+1
This patch fixes typo in the comment. Signed-off-by: David Lin <CTLIN0@nuvoton.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-15ASoC: nau8822: convert to SPDX identifiersDavid Lin2-21/+16
This patch updates license to SPDX-License-Identifier instead of verbose license text. Signed-off-by: David Lin <CTLIN0@nuvoton.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-14ASoC: amd: fix memory leak of i2s_data on error returnColin Ian King1-0/+1
Currently when snd_pcm_hw_constraint_integer fails there is a memory leak of i2s_data on the error return path. Fix this by kfree'ing i2s_data before returning. Detected by CoverityScan, CID#1475479 ("Resource leak") Fixes: 0b87d6bcd648 ("ASoC: amd: add acp3x pcm driver dma ops") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-13ASoC: pcm3060: Add DT property for single-ended outputKirill Marinushkin2-0/+15
DAC output may be differential (default) or single-ended. Signed-off-by: Kirill Marinushkin <kmarinushkin@birdec.tech> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-13ASoC: stm32: sai: fix invalid use of sizeof in stm32_sai_add_mclk_provider()Wei Yongjun1-1/+1
sizeof() when applied to a pointer typed expression gives the size of the pointer, not that of the pointed data. Fixes: 8307b2afd386 ("ASoC: stm32: sai: set sai as mclk clock provider") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-13ASoC: amd: enable acp3x drivers buildVijendar Mukunda3-0/+10
ACP3x drivers can be built by selecting necessary kernel config option. The patch enables build support of the same. Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com> Tested-by: Ravulapati Vishnu vardhan Rao <Vishnuvardhanrao.Ravulapati@amd.com> Signed-off-by: Vijendar Mukunda <vijendar.mukunda@amd.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-13ASoC: amd: add acp3x system resume pm opVijendar Mukunda1-0/+46
When system wide suspend happens, ACP will be powered off. When system resumes, all the runtime configuration data for ACP needs to be programmed again. Added 'resume'pm call back to ACP pm ops. Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com> Tested-by: Ravulapati Vishnu vardhan Rao <Vishnuvardhanrao.Ravulapati@amd.com> Signed-off-by: Vijendar Mukunda <vijendar.mukunda@amd.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-13ASoC: amd: add acp3x runtime pm opsVijendar Mukunda1-0/+39
Added runtime PM operations for ACP3x PCM platform device. Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com> Tested-by: Ravulapati Vishnu vardhan Rao <Vishnuvardhanrao.Ravulapati@amd.com> Signed-off-by: Vijendar Mukunda <vijendar.mukunda@amd.com> Signed-off-by: Mark Brown <broonie@kernel.org>
generated by cgit v1.2.3 (git 2.39.1) at 2025-01-30 06:31:44 +0000