summaryrefslogtreecommitdiffstats
path: root/sound/soc/tegra/Kconfig
AgeCommit message (Collapse)AuthorFilesLines
2021-09-20ASoC: tegra: Add Tegra210 based Mixer driverSameer Pujar1-0/+10
The Mixer supports mixing of up to ten 7.1 audio input streams and generate five outputs (each of which can be any combination of the ten input streams) This patch registers Mixer driver with ASoC framework. The component driver exposes DAPM widgets, routes and kcontrols for the device. The DAI driver exposes Mixer interfaces, which can be used to connect different components in the ASoC layer. Makefile and Kconfig support is added to allow build the driver. It can be enabled in the DT via "nvidia,tegra210-amixer" compatible binding. Signed-off-by: Sameer Pujar <spujar@nvidia.com> Link: https://lore.kernel.org/r/1631551342-25469-11-git-send-email-spujar@nvidia.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-09-20ASoC: tegra: Add Tegra210 based ADX driverSameer Pujar1-0/+11
The Audio Demultiplexer (ADX) block takes an input stream with up to 16 channels and demultiplexes it into four output streams of up to 16 channels each. A byte RAM helps to form output frames by any combination of bytes from the input frame. Its design is identical to that of byte RAM in the AMX except that the data flow direction is reversed. This patch registers ADX driver with ASoC framework. The component driver exposes DAPM widgets, routes and kcontrols for the device. The DAI driver exposes ADX interfaces, which can be used to connect different components in the ASoC layer. Makefile and Kconfig support is added to allow build the driver. It can be enabled in the DT via "nvidia,tegra210-adx" compatible binding. Signed-off-by: Sameer Pujar <spujar@nvidia.com> Link: https://lore.kernel.org/r/1631551342-25469-10-git-send-email-spujar@nvidia.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-09-20ASoC: tegra: Add Tegra210 based AMX driverSameer Pujar1-0/+9
The Audio Multiplexer (AMX) block can multiplex up to four input streams each of which can have maximum 16 channels and generate an output stream with maximum 16 channels. A byte RAM helps to form an output frame by any combination of bytes from the input frames. This patch registers AMX driver with ASoC framework. The component driver exposes DAPM widgets, routes and kcontrols for the device. The DAI driver exposes AMX interfaces, which can be used to connect different components in the ASoC layer. Makefile and Kconfig support is added to allow build the driver. It can be enabled in the DT via "nvidia,tegra210-amx" for Tegra210 and Tegra186. For Tegra194 and later, "nvidia,tegra194-amx" can be used. Signed-off-by: Sameer Pujar <spujar@nvidia.com> Link: https://lore.kernel.org/r/1631551342-25469-9-git-send-email-spujar@nvidia.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-09-20ASoC: tegra: Add Tegra210 based SFC driverSameer Pujar1-0/+9
The Sampling Frequency Converter (SFC) converts the sampling frequency of the input signal from one frequency to another. It supports sampling frequency conversions of streams of up to two channels (stereo). This patch registers SFC driver with ASoC framework. The component driver exposes DAPM widgets, routes and kcontrols for the device. The DAI driver exposes SFC interfaces, which can be used to connect different components in the ASoC layer. Makefile and Kconfig support is added to allow build the driver. It can be enabled in the DT via "nvidia,tegra210-sfc" compatible binding. Signed-off-by: Sameer Pujar <spujar@nvidia.com> Link: https://lore.kernel.org/r/1631551342-25469-8-git-send-email-spujar@nvidia.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-09-20ASoC: tegra: Add Tegra210 based MVC driverSameer Pujar1-0/+9
The Master Volume Control (MVC) provides gain or attenuation to a digital signal path. It can be used in input or output signal path for per-stream volume control or it can be used as master volume control. The MVC block has one input and one output. The input digital stream can be mono or multi-channel (up to 7.1 channels) stream. An independent mute control is also included in the MVC block. This patch registers MVC driver with ASoC framework. The component driver exposes DAPM widgets, routes and kcontrols for the device. The DAI driver exposes MVC interfaces, which can be used to connect different components in the ASoC layer. Makefile and Kconfig support is added to allow build the driver. It can be enabled in the DT via "nvidia,tegra210-mvc" compatible binding. Signed-off-by: Sameer Pujar <spujar@nvidia.com> Link: https://lore.kernel.org/r/1631551342-25469-7-git-send-email-spujar@nvidia.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-06-15ASoC: tegra: Unify ASoC machine driversDmitry Osipenko1-0/+12
Squash all machine drivers into a single-universal one. This reduces code duplication, eases addition of a new drivers and upgrades older code to a modern Linux kernel APIs. Suggested-by: Jonathan Hunter <jonathanh@nvidia.com> Co-developed-by: Ion Agorria <ion@agorria.com> Signed-off-by: Ion Agorria <ion@agorria.com> Co-developed-by: Svyatoslav Ryhel <clamor95@gmail.com> Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com> Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Link: https://lore.kernel.org/r/20210529154649.25936-3-digetx@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-02-01ASoC: tegra: SND_SOC_TEGRA_AUDIO_GRAPH_CARD should depend on SND_SOC_TEGRAGeert Uytterhoeven1-20/+13
Audio Graph Card based Tegra driver is only useful on NVIDIA Tegra SoCs. Hence add a dependency on SND_SOC_TEGRA, to prevent asking the user about this driver when configuring a kernel without Tegra sound support. Wrap all Tegra sound config options inside a big if/endif block, instead of just adding the dependency to the single config option that does not have it yet, to preventing similar future mistakes. Fixes: 202e2f7745437aa5 ("ASoC: tegra: Add audio graph based card driver") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Sameer Pujar <spujar@nvidia.com> Link: https://lore.kernel.org/r/20210129125915.2652952-1-geert+renesas@glider.be Signed-off-by: Mark Brown <broonie@kernel.org>
2021-01-19ASoC: tegra: Add audio graph based card driverSameer Pujar1-0/+9
Add Tegra audio machine driver which is based on generic audio graph card driver. It re-uses most of the common stuff from audio graph driver and uses the same DT binding. Required Tegra specific customizations are done in the driver and additional DT bindings are required for clock handling. Details on the customizations done: - Update PLL rates at runtime: Tegra HW supports multiple sample rates (multiples of 8x and 11.025x) and both of these groups require different PLL rates. Hence there is a requirement to update this at runtime. This is achieved by providing a custom 'snd_soc_ops' and in hw_param() callback PLL rate is updated as per the sample rate. - Internal structure 'tegra_audio_graph_data' is used to maintain clock handles of PLL. - The 'force_dpcm' flag is set to use DPCM for all DAI links. - The 'component_chaining' flag is set to use DPCM with component model. Signed-off-by: Sameer Pujar <spujar@nvidia.com> Reviewed-by: Jon Hunter <jonathanh@nvidia.com> Link: https://lore.kernel.org/r/1611048496-24650-4-git-send-email-spujar@nvidia.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-10-30ASoC: tegra20-spdif: remove "default m"Michał Mirosław1-1/+0
Make tegra20-spdif default to N as all other drivers do. Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Fixes: 774fec338bfc ("ASoC: Tegra: Implement SPDIF CPU DAI") Link: https://lore.kernel.org/r/8756eb5aac561173aa222c9cb64dd314ab1b1f9b.1603925200.git.mirq-linux@rere.qmqm.pl Signed-off-by: Mark Brown <broonie@kernel.org>
2020-07-21ASoC: tegra: Add Tegra210 based ADMAIF driverSameer Pujar1-0/+12
ADMAIF is the interface between ADMA and AHUB. Each ADMA channel that sends/receives data to/from AHUB must intreface through an ADMAIF channel. ADMA channel sending data to AHUB pairs with an ADMAIF Tx channel and similarly ADMA channel receiving data from AHUB pairs with an ADMAIF Rx channel. Buffer size is configurable for each ADMAIF channel, but currently SW uses default values. This patch registers ADMAIF driver with ASoC framework. The component driver exposes DAPM widgets, routes and kcontrols for the device. The DAI driver exposes ADMAIF interfaces, which can be used to connect different components in the ASoC layer. Makefile and Kconfig support is added to allow to build the driver. The ADMAIF device can be enabled in the DT via "nvidia,tegra210-admaif" compatible binding. Tegra PCM driver is updated to expose required PCM interfaces and snd_pcm_ops callbacks. Signed-off-by: Sameer Pujar <spujar@nvidia.com> Link: https://lore.kernel.org/r/1595134890-16470-8-git-send-email-spujar@nvidia.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-07-20ASoC: tegra: Add Tegra186 based DSPK driverSameer Pujar1-0/+13
The Digital Speaker Controller (DSPK) converts the multi-bit Pulse Code Modulation (PCM) audio input to oversampled 1-bit Pulse Density Modulation (PDM) output. From the signal flow perpsective, the DSPK can be viewed as a PDM transmitter that up-samples the input to the desired sampling rate by interpolation then converts the oversampled PCM input to the desired 1-bit output via Delta Sigma Modulation (DSM). This patch registers DSPK component with ASoC framework. The component driver exposes DAPM widgets, routes and kcontrols for the device. The DAI driver exposes DSPK interfaces, which can be used to connect different components in the ASoC layer. Makefile and Kconfig support is added to allow to build the driver. The DSPK devices can be enabled in the DT via "nvidia,tegra186-dspk" compatible binding. This driver can be used on Tegra194 chip as well. Signed-off-by: Sameer Pujar <spujar@nvidia.com> Link: https://lore.kernel.org/r/1595134890-16470-7-git-send-email-spujar@nvidia.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-07-20ASoC: tegra: Add Tegra210 based AHUB driverSameer Pujar1-0/+10
The Audio Hub (AHUB) comprises a collection of hardware accelerators for audio pre/post-processing and a programmable full crossbar (XBAR) for routing audio data across these accelerators in time and in parallel. AHUB supports multiple interfaces to I2S, DSPK, DMIC etc., XBAR is a switch used to configure or modify audio routing between HW accelerators present inside AHUB. This patch registers AHUB component with ASoC framework. The component driver exposes DAPM widgets, routes and kcontrols for the device. The DAI driver exposes AHUB interfaces, which can be used to connect different components in the ASoC layer. Currently the driver takes care of XBAR programming to allow audio data flow through various clients of the AHUB. Makefile and Kconfig support is added to allow to build the driver. The AHUB component can be enabled in the DT via below compatible bindings. - "nvidia,tegra210-ahub" for Tegra210 - "nvidia,tegra186-ahub" for Tegra186 and Tegra194 Signed-off-by: Sameer Pujar <spujar@nvidia.com> Link: https://lore.kernel.org/r/1595134890-16470-6-git-send-email-spujar@nvidia.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-07-20ASoC: tegra: Add Tegra210 based I2S driverSameer Pujar1-0/+10
The Inter-IC Sound (I2S) controller implements full-duplex, bi-directional and single direction point to point serial interface. It can interface with I2S compatible devices. Tegra I2S controller can operate as both master and slave. This patch registers I2S controller with ASoC framework. The component driver exposes DAPM widgets, routes and kcontrols for the device. The DAI driver exposes I2S interfaces, which can be used to connect different components in the ASoC layer. Makefile and Kconfig support is added to allow to build the driver. The I2S devices can be enabled in the DT via "nvidia,tegra210-i2s" compatible binding. Signed-off-by: Sameer Pujar <spujar@nvidia.com> Link: https://lore.kernel.org/r/1595134890-16470-5-git-send-email-spujar@nvidia.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-07-20ASoC: tegra: Add Tegra210 based DMIC driverSameer Pujar1-0/+11
The Digital MIC (DMIC) Controller is used to interface with Pulse Density Modulation (PDM) input devices. The DMIC controller implements a converter to convert PDM signals to Pulse Code Modulation (PCM) signals. From signal flow perspective, the DMIC can be viewed as a PDM receiver. This patch registers DMIC component with ASoC framework. The component driver exposes DAPM widgets, routes and kcontrols for the device. The DAI driver exposes DMIC interfaces, which can be used to connect different components in the ASoC layer. Makefile and Kconfig support is added to allow to build the driver. The DMIC devices can be enabled in the DT via "nvidia,tegra210-dmic" compatible string. This driver can be used for Tegra186 and Tegra194 chips as well. Signed-off-by: Sameer Pujar <spujar@nvidia.com> Link: https://lore.kernel.org/r/1595134890-16470-4-git-send-email-spujar@nvidia.com Signed-off-by: Mark Brown <broonie@kernel.org>
2019-05-21treewide: Add SPDX license identifier - Makefile/KconfigThomas Gleixner1-0/+1
Add SPDX license identifiers to all Make/Kconfig files which: - Have no license information of any form These files fall under the project license, GPL v2 only. The resulting SPDX license identifier is: GPL-2.0-only Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-08-18ASoC: tegra: Remove SoC-specific Kconfig depends and selectsPaul Kocialkowski1-28/+14
This removes the SoC-specific dependencies on the platform drivers, as well as SoC-specific selections of platform drivers for the machine drivers. The rationale behind this change is that the dependencies are not actual build dependencies but run-time ones. The previously listed SoCs were also incomplete: for instance, tegra124 uses the tegra30 platform drivers, which could not be built without ARCH_TEGRA_3x_SOC set. Descriptions of the tristates are also added to allow these options to be set via defconfig/menuconfig. Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2016-08-12ASoC: tegra: add tegra sgtl5000 machine driverMarcel Ziswiler1-0/+11
This binding and driver describe/support playback to headphones, and capture from line-in and microphone. This driver is useful for the Toradex Apalis T30, Apalis TK1 and Colibri T30 modules. Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com> Reviewed-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2015-01-07ASoC: tegra: Add platform driver for rt5677 audio codecAnatol Pomozov1-0/+10
The driver supports NVIDIA Tegra Ryu board Sponsored: Google ChromeOS Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2014-03-07ASoC: update Kconfig of AIC23 users to select I2C variantMax Filippov1-1/+1
Now that AIC23 supports two control interfaces all existing I2C users should select I2C variant. Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-01-23Merge tag 'cleanup-for-linus' of ↵Linus Torvalds1-0/+2
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC cleanups from Olof Johansson: "This is the branch where we usually queue up cleanup efforts, moving drivers out of the architecture directory, header file restructuring, etc. Sometimes they tangle with new development so it's hard to keep it strictly to cleanups. Some of the things included in this branch are: * Atmel SAMA5 conversion to common clock * Reset framework conversion for tegra platforms - Some of this depends on tegra clock driver reworks that are shared with Mike Turquette's clk tree. * Tegra DMA refactoring, which are shared branches with the DMA tree. * Removal of some header files on exynos to prepare for multiplatform" * tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits) ARM: mvebu: move Armada 370/XP specific definitions to armada-370-xp.h ARM: mvebu: remove prototypes of non-existing functions from common.h ARM: mvebu: move ARMADA_XP_MAX_CPUS to armada-370-xp.h serial: sh-sci: Rework baud rate calculation serial: sh-sci: Compute overrun_bit without using baud rate algo serial: sh-sci: Remove unused GPIO request code serial: sh-sci: Move overrun_bit and error_mask fields out of pdata serial: sh-sci: Support resources passed through platform resources serial: sh-sci: Don't check IRQ in verify port operation serial: sh-sci: Set the UPF_FIXED_PORT flag serial: sh-sci: Remove duplicate interrupt check in verify port op serial: sh-sci: Simplify baud rate calculation algorithms serial: sh-sci: Remove baud rate calculation algorithm 5 serial: sh-sci: Sort headers alphabetically ARM: EXYNOS: Kill exynos_pm_late_initcall() ARM: EXYNOS: Consolidate selection of PM_GENERIC_DOMAINS for Exynos4 ARM: at91: switch Calao QIL-A9260 board to DT clk: at91: fix pmc_clk_ids data type attriubte PM / devfreq: use inclusion <mach/map.h> instead of <plat/map-s5p.h> ARM: EXYNOS: remove <mach/regs-clock.h> for exynos ...
2013-12-11ASoC: tegra: use reset frameworkStephen Warren1-0/+2
Tegra's clock driver now provides an implementation of the common reset API (include/linux/reset.h). Use this instead of the old Tegra- specific API; that will soon be removed. This change also renames "clock"/"clk" to "modules"/"mod" in symbols related to entries in configlink_clocks[], since: - We don't care about clock handles any more, but rather reset handles, so the old name isn't applicable. - It really is a list of modules on the bus, about which we currently only care about reset handles. If we start caring about any other aspect of the modules in the future, we won't have to rename all these symbols again. Note: The addition of "depends COMMON_CLOCK" is something that was missing before, not a new requirement. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Mark Brown <broonie@linaro.org> Reviewed-by: Thierry Reding <treding@nvidia.com>
2013-12-05ASoC: tegra: add tegra+MAX98090 machine driverStephen Warren1-0/+10
Initially, this binding and driver only describe/support playback to headphones and speakers, and capture from the external microphone, with GPIO-based jack detection for the headphone jack only. This driver is useful for the Venice2 board. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-07-17ASoC: tegra: Enable COMPILE_TEST buildsMark Brown1-1/+1
Since there is no architecture dependency in the code allow it to be built on any platform when COMPILE_TEST is enabled. Signed-off-by: Mark Brown <broonie@linaro.org> Acked-by: Stephen Warren <swarren@nvidia.com>
2013-07-17ASoC: tegra: Always use the generic dmaengine helper libraryMark Brown1-1/+1
The usage of the dmaengine helpers is unconditional, especially when doing compile testing. Reported-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-07-17ASoC: tegra: Add GPIOLIB dependenciesMark Brown1-5/+5
For build coverage. Signed-off-by: Mark Brown <broonie@linaro.org> Acked-by: Stephen Warren <swarren@nvidia.com>
2013-06-12ASoC: tegra: add tegra+RT5640 machine driverStephen Warren1-0/+10
Initially, this binding and driver only describe/support playback to headphones and speakers. This driver will support Beaver and Dalmore. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-04-17ASoC: tegra: Use generic dmaengine PCMLars-Peter Clausen1-1/+1
Use the generic dmaengine PCM driver instead of a custom implementation. Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-01-17ASoC: tegra: add tegra machine driver using wm9712 codecLucas Stach1-0/+9
This adds a very simple machine driver using the Wolfson wm9712 AC97 codec. Signed-off-by: Lucas Stach <dev@lynxeye.de> Reviewed-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-01-14ASoC: tegra: add ac97 host driverLucas Stach1-0/+10
This adds the driver for the Tegra 2x AC97 host controller. Signed-off-by: Lucas Stach <dev@lynxeye.de> Reviewed-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-17ASoC: tegra: remove support of legacy DMA driver based accessLaxman Dewangan1-1/+1
Remove the support code which uses the legacy APB DMA driver for accessing the I2S FIFO. The driver will use the dmaengine based APB DMA driver for accessing reqding/writing to I2S FIFO. Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-24Merge tag 'sound-3.6' of ↵Linus Torvalds1-1/+2
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound Pull sound update from Takashi Iwai: "This is a fairly quiet release in all sound area. Only a little bit of changes in the core side while most of changes are seen in the drivers. HD-audio: - A few new codec additions for Nvidia, Realtek and VIA - Intel Haswell audio support - Support for "phantom" jacks for consistent jack reporting - Major clean-ups in HDMI/DP driver codes - A workaround for inverted digital-mic pins with Realtek codecs - Removal of beep_mode=2 option ASoC: - Added the ability to add and remove DAPM paths dynamically, mostly for reparenting on clock changes - New machine drivers for Marvell Brownstone, ST-Ericsson Ux500 reference platform and ttc-dkp - New CPU drivers for Blackfin BF6xx SPORTs in I2S mode, Marvell MMP, Synopsis Designware I2S controllers, and SPEAr DMA and S/PDIF - New CODEC drivers for Dialog DA732x, ST STA529, ST-Ericsson AB8500, TI Isabelle and Wolfson Microelectronics WM5102 and WM5110 - DAPM fixes for the recent locking changes - Fix for _PRE and _POST widgets (which have been broken for a few releases now) - A couple of minor driver updates Misc - Conversion to new dev_pm_ops in platform and PCI drivers - LTC support and some fixes in PCXHR driver - A few fixes and PM support for ISA OPti9xx and WSS cards - Some TLV code cleanup - Move driver-specific headers from include/sound to local dirs" * tag 'sound-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (212 commits) ASoC: dapm: Fix _PRE and _POST events for DAPM performance improvements ALSA: hda - add dock support for Thinkpad X230 Tablet ALSA: hda - Turn on PIN_OUT from hdmi playback prepare. ASoC imx-audmux: add MX31_AUDMUX_PORT7_SSI_PINS_7 define ASoC: littlemill: Add userspace control of the WM1250 I/O ASoC: wm8994: Update micdet for irqdomain conversion ALSA: hda - make sure alc268 does not OOPS on codec parse ALSA: hda - Add support for Realtek ALC282 ALSA: hda - Fix index number conflicts of phantom jacks ALSA: opti9xx: Fix section mismatch by PM support ALSA: snd-opti9xx: Implement suspend/resume ALSA: hda - Add new GPU codec ID to snd-hda ALSA: hda - Fix driver type of Haswell controller to AZX_DRIVER_SCH ALSA: hda - add Haswell HDMI codec id ALSA: hda - Add DeviceID for Haswell HDA ALSA: wss_lib: Fix resume on Yamaha OPL3-SAx ALSA: wss_lib: fix suspend/resume ALSA: es1938: replace TLV_DB_RANGE_HEAD with DECLARE_TLV_DB_RANGE ALSA: tlv: add DECLARE_TLV_DB_RANGE() ALSA: tlv: add DECLARE_TLV_CONTAINER() ...
2012-07-03ASoC: tegra: use dmaengine based dma driverLaxman Dewangan1-1/+2
Use the dmaengine based Tegra APB DMA driver for data transfer between SPI fifo and memory in place of legacy Tegra APB DMA. Because generic soc-dmaengine-pcm uses the DMAs API based on dmaengine, using the exported APIs provided by this generic driver. The new driver is selected if legacy driver is not selected and new dma driver is enabled through config file. Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Tested-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-11ASoC: tegra: simplify Kconfig dependenciesStephen Warren1-9/+1
The Tegra ASoC machine drivers only depend on Tegra architecture support to compile, not specific board support. Remove Kconfig dependencies on any particular board. This is required since Kconfig options for boards are going away given the migration to device tree. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-05-19ASoC: tegra: Add machine driver for WM8753 codecStephen Warren1-0/+10
One such machine is Whistler. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-04-13ASoC: tegra: select REGMAP_MMIOStephen Warren1-0/+1
All Tegra ASoC drivers will be reworked to use MMIO regmaps. Select this in Kconfig. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-04-13ASoC: tegra: add Kconfig and Makefile support for Tegra30Stephen Warren1-0/+18
This adds Kconfig options for the Tegra30 AHUB and I2S controller, and updates the Tegra+WM8903 machine driver Kconfig to select those. Includes a squashed bugfix from Sumit Bhattacharya <sumitb@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-04-06ASoC: tegra: complete Tegra->Tegra20 renamingStephen Warren1-10/+10
Rename Tegra20-specific Kconfig variables, module filenames, all internal symbol names, clocks, and platform devices, to reflect the fact the DAS and I2S drivers are for a specific HW version. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-04-05ASoC: tegra: make Tegra20 drivers depend on Tegra20 supportStephen Warren1-6/+6
Without this, the Tegra20 drivers can be built into a kernel that's built only for Tegra30. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-04-05ASoC: tegra: drop Kconfig description for SND_SOC_TEGRA_DASStephen Warren1-1/+1
The DAS, I2S, and SPDIF Kconfig options are intended to be selected by the Kconfig options for ASoC machine drivers. As such, they don't need to be user-visible themselves. Drop the description from the DAS variable to achieve this. I2S and SPDIF already don't have a description. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-04-01ASoC: tegra: introduce separate Kconfig variable for DAS driverStephen Warren1-0/+9
This is mainly for symmetry with a future Tegra30 driver, where the equivalent of the DAS (the AHUB) is useful separately from the I2S driver. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-04-01ASoC: tegra: fix Kconfig SND_SOC_TEGRA_ALC5632 indentationStephen Warren1-7/+7
Indent with TABs to be consistent with the rest of the file. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-12-20ASoC: Tegra machine ASoC driver for boards using ALC5332 codecLeon Romanovsky1-0/+9
At this stage only Toshiba AC100/Dynabook supported. Signed-off-by: Leon Romanovsky <leon@leon.nu> Signed-off-by: Andrey Danin <danindrey@mail.ru> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-07-05ASoC: Tegra: Implement SPDIF CPU DAIStephen Warren1-0/+9
This is a minimal driver for the Tegra SPDIF controller. In hardware, the SPDIF output signal is always routed to any active HDMI display controllers, and may also be routed to external pins on Tegra using the pinmux. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-05-03ASoC: tegra: TrimSlice machine supportMike Rapoport1-0/+8
Signed-off-by: Mike Rapoport <mike@compulab.co.il> Acked-by: Stephen Warren <swarren@nvidia.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-04-26ASoC: Remove default settings from Tegra KconfigMark Brown1-3/+0
There needs to be a strong reason for overriding the Kconfig default. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@ti.com>
2011-04-21Merge branch 'tegra' into for-2.6.40Mark Brown1-1/+8
Fix up merge with Harmony driver rename. Conflicts: sound/soc/tegra/Kconfig
2011-04-21ARM: Tegra: select MACH_HAS_SND_SOC_TEGRA_WM8903Stephen Warren1-0/+7
CONFIG_SND_SOC_TEGRA_WM8903 is useful for many Tegra boards. To avoid the ASoC tegra/Kconfig enumerating them all, instead have the Tegra machine Kconfig select MACH_HAS_SND_SOC_TEGRA_WM8903 where appropriate, and have SND_SOC_TEGRA_WM8903 depend on this. [Redid ASoC diff so it applies. -- broonie] Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Olof Johansson <olof@lixom.net> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-04-18ASoC: Tegra: Support more boardsStephen Warren1-3/+4
* Ventana is identical to Harmony. * Seaboard, Kaen, and Aebl are all pretty similar, mainly with slightly different sets of GPIOs, and slightly different WM8903 pin connectivity. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-04-18ASoC: Tegra: Rename Kconfig SND_TEGRA_SOC_* to SND_SOC_TEGRA_*Stephen Warren1-6/+6
The previous commit renames SND_TEGRA_SOC_HARMONY to SND_TEGRA_SOC_WM8903. While we're breaking people's .config files, rename all Tegra/SOC-related Kconfig variables to be more consistent with at least the core codec variables. Note that there exist machines that name their variables both ways. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-04-18ASoC: Tegra: Rename harmony.c to tegra_wm8903.cStephen Warren1-4/+5
Soon, this machine driver will be updated to handle a number of Tegra boards using the WM8903 codec. Rename the file in advance to reflect this. Fix the content of tegra_wm8903.c to match the rename; replace references to Harmony board with something more generic. * s/struct tegra_harmony/struct tegra_wm8903/ * s/harmony/machine/ # variable name * Similar rename for some functions * Similar comment fix * Similar MODULE_DESCRIPTION fix Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-29 17:53:50 +0000