summaryrefslogtreecommitdiffstats
path: root/net
AgeCommit message (Collapse)AuthorFilesLines
2017-12-01sctp: abandon the whole msg if one part of a fragmented message is abandonedXin Long2-4/+15
As rfc3758#section-3.1 demands: A3) When a TSN is "abandoned", if it is part of a fragmented message, all other TSN's within that fragmented message MUST be abandoned at the same time. Besides, if it couldn't handle this, the rest frags would never get assembled in peer side. This patch supports it by adding abandoned flag in sctp_datamsg, when one chunk is being abandoned, set chunk->msg->abandoned as well. Next time when checking for abandoned, go checking chunk->msg->abandoned first. Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-01sctp: only update outstanding_bytes for transmitted queue when doing ↵Xin Long1-2/+4
prsctp_prune Now outstanding_bytes is only increased when appending chunks into one packet and sending it at 1st time, while decreased when it is about to move into retransmit queue. It means outstanding_bytes value is already decreased for all chunks in retransmit queue. However sctp_prsctp_prune_sent is a common function to check the chunks in both transmitted and retransmit queue, it decrease outstanding_bytes when moving a chunk into abandoned queue from either of them. It could cause outstanding_bytes underflow, as it also decreases it's value for the chunks in retransmit queue. This patch fixes it by only updating outstanding_bytes for transmitted queue when pruning queues for prsctp prio policy, the same fix is also needed in sctp_check_transmitted. Fixes: 8dbdf1f5b09c ("sctp: implement prsctp PRIO policy") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-30sit: update frag_off infoHangbin Liu1-0/+1
After parsing the sit netlink change info, we forget to update frag_off in ipip6_tunnel_update(). Fix it by assigning frag_off with new value. Reported-by: Jianlin Shi <jishi@redhat.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-30tcp: remove buggy call to tcp_v6_restore_cb()Eric Dumazet1-1/+0
tcp_v6_send_reset() expects to receive an skb with skb->cb[] layout as used in TCP stack. MD5 lookup uses tcp_v6_iif() and tcp_v6_sdif() and thus TCP_SKB_CB(skb)->header.h6 This patch probably fixes RST packets sent on behalf of a timewait md5 ipv6 socket. Before Florian patch, tcp_v6_restore_cb() was needed before jumping to no_tcp_socket label. Fixes: 271c3b9b7bda ("tcp: honour SO_BINDTODEVICE for TW_RST case too") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Florian Westphal <fw@strlen.de> Acked-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-30act_sample: get rid of tcf_sample_cleanup_rcu()Cong Wang1-11/+3
Similar to commit d7fb60b9cafb ("net_sched: get rid of tcfa_rcu"), TC actions don't need to respect RCU grace period, because it is either just detached from tc filter (standalone case) or it is removed together with tc filter (bound case) in which case RCU grace period is already respected at filter layer. Fixes: 5c5670fae430 ("net/sched: Introduce sample tc action") Reported-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Cc: Yotam Gigi <yotamg@mellanox.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-30Merge tag 'rxrpc-fixes-20171129' of ↵David S. Miller5-27/+35
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs David Howells says: ==================== rxrpc: Fixes Here are three patches for AF_RXRPC. One removes some whitespace, one fixes terminal ACK generation and the third makes a couple of places actually use the timeout value just determined rather than ignoring it. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-29Merge tag 'nfsd-4.15-1' of git://linux-nfs.org/~bfields/linuxLinus Torvalds3-5/+5
Pull nfsd fixes from Bruce Fields: "I screwed up my merge window pull request; I only sent half of what I meant to. There were no new features, just bugfixes of various importance and some very minor cleanup, so I think it's all still appropriate for -rc2. Highlights: - Fixes from Trond for some races in the NFSv4 state code. - Fix from Naofumi Honda for a typo in the blocked lock notificiation code - Fixes from Vasily Averin for some problems starting and stopping lockd especially in network namespaces" * tag 'nfsd-4.15-1' of git://linux-nfs.org/~bfields/linux: (23 commits) lockd: fix "list_add double add" caused by legacy signal interface nlm_shutdown_hosts_net() cleanup race of nfsd inetaddr notifiers vs nn->nfsd_serv change race of lockd inetaddr notifiers vs nlmsvc_rqst change SUNRPC: make cache_detail structures const NFSD: make cache_detail structures const sunrpc: make the function arg as const nfsd: check for use of the closed special stateid nfsd: fix panic in posix_unblock_lock called from nfs4_laundromat lockd: lost rollback of set_grace_period() in lockd_down_net() lockd: added cleanup checks in exit_net hook grace: replace BUG_ON by WARN_ONCE in exit_net hook nfsd: fix locking validator warning on nfs4_ol_stateid->st_mutex class lockd: remove net pointer from messages nfsd: remove net pointer from debug messages nfsd: Fix races with check_stateid_generation() nfsd: Ensure we check stateid validity in the seqid operation checks nfsd: Fix race in lock stateid creation nfsd4: move find_lock_stateid nfsd: Ensure we don't recognise lock stateids after freeing them ...
2017-11-29Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds37-402/+917
Pull networking fixes from David Miller: 1) The forcedeth conversion from pci_*() DMA interfaces to dma_*() ones missed one spot. From Zhu Yanjun. 2) Missing CRYPTO_SHA256 Kconfig dep in cfg80211, from Johannes Berg. 3) Fix checksum offloading in thunderx driver, from Sunil Goutham. 4) Add SPDX to vm_sockets_diag.h, from Stephen Hemminger. 5) Fix use after free of packet headers in TIPC, from Jon Maloy. 6) "sizeof(ptr)" vs "sizeof(*ptr)" bug in i40e, from Gustavo A R Silva. 7) Tunneling fixes in mlxsw driver, from Petr Machata. 8) Fix crash in fanout_demux_rollover() of AF_PACKET, from Mike Maloney. 9) Fix race in AF_PACKET bind() vs. NETDEV_UP notifier, from Eric Dumazet. 10) Fix regression in sch_sfq.c due to one of the timer_setup() conversions. From Paolo Abeni. 11) SCTP does list_for_each_entry() using wrong struct member, fix from Xin Long. 12) Don't use big endian netlink attribute read for IFLA_BOND_AD_ACTOR_SYSTEM, it is in cpu endianness. Also from Xin Long. 13) Fix mis-initialization of q->link.clock in CBQ scheduler, preventing adding filters there. From Jiri Pirko. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (67 commits) ethernet: dwmac-stm32: Fix copyright net: via: via-rhine: use %p to format void * address instead of %x net: ethernet: xilinx: Mark XILINX_LL_TEMAC broken on 64-bit myri10ge: Update MAINTAINERS net: sched: cbq: create block for q->link.block atm: suni: remove extraneous space to fix indentation atm: lanai: use %p to format kernel addresses instead of %x VSOCK: Don't set sk_state to TCP_CLOSE before testing it atm: fore200e: use %pK to format kernel addresses instead of %x ambassador: fix incorrect indentation of assignment statement vxlan: use __be32 type for the param vni in __vxlan_fdb_delete bonding: use nla_get_u64 to extract the value for IFLA_BOND_AD_ACTOR_SYSTEM sctp: use right member as the param of list_for_each_entry sch_sfq: fix null pointer dereference at timer expiration cls_bpf: don't decrement net's refcount when offload fails net/packet: fix a race in packet_bind() and packet_notifier() packet: fix crash in fanout_demux_rollover() sctp: remove extern from stream sched sctp: force the params with right types for sctp csum apis sctp: force SCTP_ERROR_INV_STRM with __u32 when calling sctp_chunk_fail ...
2017-11-29rxrpc: Fix variable overwriteGustavo A. R. Silva2-2/+2
Values assigned to both variable resend_at and ack_at are overwritten before they can be used. The correct fix here is to add 'now' to the previously computed value in resend_at and ack_at. Addresses-Coverity-ID: 1462262 Addresses-Coverity-ID: 1462263 Addresses-Coverity-ID: 1462264 Fixes: beb8e5e4f38c ("rxrpc: Express protocol timeouts in terms of RTT") Link: https://marc.info/?i=17004.1511808959%40warthog.procyon.org.uk Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com> Signed-off-by: David Howells <dhowells@redhat.com>
2017-11-29rxrpc: Fix ACK generation from the connection event processorDavid Howells1-21/+29
Repeat terminal ACKs and now terminal ACKs are now generated from the connection event processor rather from call handling as this allows us to discard client call structures as soon as possible and free up the channel for a follow on call. However, in ACKs so generated, the additional information trailer is malformed because the padding that's meant to be in the middle isn't included in what's transmitted. Fix it so that the 3 bytes of padding are included in the transmission. Further, the trailer is misaligned because of the padding, so assigment to the u16 and u32 fields inside it might cause problems on some arches, so fix this by breaking the padding and the trailer out of the packed struct. (This also deals with potential compiler weirdies where some of the nested structs are packed and some aren't). The symptoms can be seen in wireshark as terminal DUPLICATE or IDLE ACK packets in which the Max MTU, Interface MTU and rwind fields have weird values and the Max Packets field is apparently missing. Reported-by: Jeffrey Altman <jaltman@auristor.com> Signed-off-by: David Howells <dhowells@redhat.com>
2017-11-29rxrpc: Clean up whitespaceDavid Howells3-4/+4
Clean up some whitespace from rxrpc. Signed-off-by: David Howells <dhowells@redhat.com>
2017-11-28net: sched: cbq: create block for q->link.blockJiri Pirko1-1/+8
q->link.block is not initialized, that leads to EINVAL when one tries to add filter there. So initialize it properly. This can be reproduced by: $ tc qdisc add dev eth0 root handle 1: cbq avpkt 1000 rate 1000Mbit bandwidth 1000Mbit $ tc filter add dev eth0 parent 1: protocol ip prio 100 u32 match ip protocol 0 0x00 flowid 1:1 Reported-by: Jaroslav Aster <jaster@redhat.com> Reported-by: Ivan Vecera <ivecera@redhat.com> Fixes: 6529eaba33f0 ("net: sched: introduce tcf block infractructure") Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Eelco Chaudron <echaudro@redhat.com> Reviewed-by: Ivan Vecera <ivecera@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-28VSOCK: Don't set sk_state to TCP_CLOSE before testing itJorgen Hansen1-2/+2
A recent commit (3b4477d2dcf2) converted the sk_state to use TCP constants. In that change, vmci_transport_handle_detach was changed such that sk->sk_state was set to TCP_CLOSE before we test whether it is TCP_SYN_SENT. This change moves the sk_state change back to the original locations in that function. Signed-off-by: Jorgen Hansen <jhansen@vmware.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-28sctp: use right member as the param of list_for_each_entryXin Long1-3/+3
Commit d04adf1b3551 ("sctp: reset owner sk for data chunks on out queues when migrating a sock") made a mistake that using 'list' as the param of list_for_each_entry to traverse the retransmit, sacked and abandoned queues, while chunks are using 'transmitted_list' to link into these queues. It could cause NULL dereference panic if there are chunks in any of these queues when peeling off one asoc. So use the chunk member 'transmitted_list' instead in this patch. Fixes: d04adf1b3551 ("sctp: reset owner sk for data chunks on out queues when migrating a sock") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-28sch_sfq: fix null pointer dereference at timer expirationPaolo Abeni1-0/+1
While converting sch_sfq to use timer_setup(), the commit cdeabbb88134 ("net: sched: Convert timers to use timer_setup()") forgot to initialize the 'sch' field. As a result, the timer callback tries to dereference a NULL pointer, and the kernel does oops. Fix it initializing such field at qdisc creation time. Fixes: cdeabbb88134 ("net: sched: Convert timers to use timer_setup()") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Kees Cook <keescook@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-28cls_bpf: don't decrement net's refcount when offload failsJakub Kicinski1-10/+13
When cls_bpf offload was added it seemed like a good idea to call cls_bpf_delete_prog() instead of extending the error handling path, since the software state is fully initialized at that point. This handling of errors without jumping to the end of the function is error prone, as proven by later commit missing that extra call to __cls_bpf_delete_prog(). __cls_bpf_delete_prog() is now expected to be invoked with a reference on exts->net or the field zeroed out. The call on the offload's error patch does not fullfil this requirement, leading to each error stealing a reference on net namespace. Create a function undoing what cls_bpf_set_parms() did and use it from __cls_bpf_delete_prog() and the error path. Fixes: aae2c35ec892 ("cls_bpf: use tcf_exts_get_net() before call_rcu()") Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-28net/packet: fix a race in packet_bind() and packet_notifier()Eric Dumazet1-0/+5
syzbot reported crashes [1] and provided a C repro easing bug hunting. When/if packet_do_bind() calls __unregister_prot_hook() and releases po->bind_lock, another thread can run packet_notifier() and process an NETDEV_UP event. This calls register_prot_hook() and hooks again the socket right before first thread is able to grab again po->bind_lock. Fixes this issue by temporarily setting po->num to 0, as suggested by David Miller. [1] dev_remove_pack: ffff8801bf16fa80 not found ------------[ cut here ]------------ kernel BUG at net/core/dev.c:7945! ( BUG_ON(!list_empty(&dev->ptype_all)); ) invalid opcode: 0000 [#1] SMP KASAN Dumping ftrace buffer: (ftrace buffer empty) Modules linked in: device syz0 entered promiscuous mode CPU: 0 PID: 3161 Comm: syzkaller404108 Not tainted 4.14.0+ #190 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 task: ffff8801cc57a500 task.stack: ffff8801cc588000 RIP: 0010:netdev_run_todo+0x772/0xae0 net/core/dev.c:7945 RSP: 0018:ffff8801cc58f598 EFLAGS: 00010293 RAX: ffff8801cc57a500 RBX: dffffc0000000000 RCX: ffffffff841f75b2 RDX: 0000000000000000 RSI: 1ffff100398b1ede RDI: ffff8801bf1f8810 device syz0 entered promiscuous mode RBP: ffff8801cc58f898 R08: 0000000000000001 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000000 R12: ffff8801bf1f8cd8 R13: ffff8801cc58f870 R14: ffff8801bf1f8780 R15: ffff8801cc58f7f0 FS: 0000000001716880(0000) GS:ffff8801db400000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000020b13000 CR3: 0000000005e25000 CR4: 00000000001406f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: rtnl_unlock+0xe/0x10 net/core/rtnetlink.c:106 tun_detach drivers/net/tun.c:670 [inline] tun_chr_close+0x49/0x60 drivers/net/tun.c:2845 __fput+0x333/0x7f0 fs/file_table.c:210 ____fput+0x15/0x20 fs/file_table.c:244 task_work_run+0x199/0x270 kernel/task_work.c:113 exit_task_work include/linux/task_work.h:22 [inline] do_exit+0x9bb/0x1ae0 kernel/exit.c:865 do_group_exit+0x149/0x400 kernel/exit.c:968 SYSC_exit_group kernel/exit.c:979 [inline] SyS_exit_group+0x1d/0x20 kernel/exit.c:977 entry_SYSCALL_64_fastpath+0x1f/0x96 RIP: 0033:0x44ad19 Fixes: 30f7ea1c2b5f ("packet: race condition in packet_bind") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Cc: Francesco Ruggeri <fruggeri@aristanetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-28packet: fix crash in fanout_demux_rollover()Mike Maloney2-23/+10
syzkaller found a race condition fanout_demux_rollover() while removing a packet socket from a fanout group. po->rollover is read and operated on during packet_rcv_fanout(), via fanout_demux_rollover(), but the pointer is currently cleared before the synchronization in packet_release(). It is safer to delay the cleanup until after synchronize_net() has been called, ensuring all calls to packet_rcv_fanout() for this socket have finished. To further simplify synchronization around the rollover structure, set po->rollover in fanout_add() only if there are no errors. This removes the need for rcu in the struct and in the call to packet_getsockopt(..., PACKET_ROLLOVER_STATS, ...). Crashing stack trace: fanout_demux_rollover+0xb6/0x4d0 net/packet/af_packet.c:1392 packet_rcv_fanout+0x649/0x7c8 net/packet/af_packet.c:1487 dev_queue_xmit_nit+0x835/0xc10 net/core/dev.c:1953 xmit_one net/core/dev.c:2975 [inline] dev_hard_start_xmit+0x16b/0xac0 net/core/dev.c:2995 __dev_queue_xmit+0x17a4/0x2050 net/core/dev.c:3476 dev_queue_xmit+0x17/0x20 net/core/dev.c:3509 neigh_connected_output+0x489/0x720 net/core/neighbour.c:1379 neigh_output include/net/neighbour.h:482 [inline] ip6_finish_output2+0xad1/0x22a0 net/ipv6/ip6_output.c:120 ip6_finish_output+0x2f9/0x920 net/ipv6/ip6_output.c:146 NF_HOOK_COND include/linux/netfilter.h:239 [inline] ip6_output+0x1f4/0x850 net/ipv6/ip6_output.c:163 dst_output include/net/dst.h:459 [inline] NF_HOOK.constprop.35+0xff/0x630 include/linux/netfilter.h:250 mld_sendpack+0x6a8/0xcc0 net/ipv6/mcast.c:1660 mld_send_initial_cr.part.24+0x103/0x150 net/ipv6/mcast.c:2072 mld_send_initial_cr net/ipv6/mcast.c:2056 [inline] ipv6_mc_dad_complete+0x99/0x130 net/ipv6/mcast.c:2079 addrconf_dad_completed+0x595/0x970 net/ipv6/addrconf.c:4039 addrconf_dad_work+0xac9/0x1160 net/ipv6/addrconf.c:3971 process_one_work+0xbf0/0x1bc0 kernel/workqueue.c:2113 worker_thread+0x223/0x1990 kernel/workqueue.c:2247 kthread+0x35e/0x430 kernel/kthread.c:231 ret_from_fork+0x2a/0x40 arch/x86/entry/entry_64.S:432 Fixes: 0648ab70afe6 ("packet: rollover prepare: per-socket state") Fixes: 509c7a1ecc860 ("packet: avoid panic in packet_getsockopt()") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Mike Maloney <maloney@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-28sctp: remove extern from stream schedXin Long4-9/+31
Now each stream sched ops is defined in different .c file and added into the global ops in another .c file, it uses extern to make this work. However extern is not good coding style to get them in and even make C=2 reports errors for this. This patch adds sctp_sched_ops_xxx_init for each stream sched ops in their .c file, then get them into the global ops by calling them when initializing sctp module. Fixes: 637784ade221 ("sctp: introduce priority based stream scheduler") Fixes: ac1ed8b82cd6 ("sctp: introduce round robin stream scheduler") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-28sctp: force SCTP_ERROR_INV_STRM with __u32 when calling sctp_chunk_failXin Long1-1/+1
This patch is to force SCTP_ERROR_INV_STRM with right type to fit in sctp_chunk_fail to avoid the sparse error. Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-27SUNRPC: make cache_detail structures constBhumika Goyal2-4/+4
Make these const as they are only getting passed to the function cache_create_net having the argument as const. Signed-off-by: Bhumika Goyal <bhumirks@gmail.com> Reviewed-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com>
2017-11-27sunrpc: make the function arg as constBhumika Goyal1-1/+1
Make the struct cache_detail *tmpl argument of the function cache_create_net as const as it is only getting passed to kmemup having the argument as const void *. Add const to the prototype too. Signed-off-by: Bhumika Goyal <bhumirks@gmail.com> Reviewed-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com>
2017-11-27tipc: eliminate access after delete in group_filter_msg()Jon Maloy1-1/+1
KASAN revealed another access after delete in group.c. This time it found that we read the header of a received message after the buffer has been released. Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-28Merge tag 'mac80211-for-davem-2017-11-27' of ↵David S. Miller5-10/+47
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211 Johannes Berg says: ==================== Four fixes: * CRYPTO_SHA256 is needed for regdb validation * mac80211: mesh path metric was wrong in some frames * mac80211: use QoS null-data packets on QoS connections * mac80211: tear down RX aggregation sessions first to drop fewer packets in HW restart scenarios ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-28sctp: set sender next_tsn for the old result with ctsn_ack_point plus 1Xin Long1-1/+1
When doing asoc reset, if the sender of the response has already sent some chunk and increased asoc->next_tsn before the duplicate request comes, the response will use the old result with an incorrect sender next_tsn. Better than asoc->next_tsn, asoc->ctsn_ack_point can't be changed after the sender of the response has performed the asoc reset and before the peer has confirmed it, and it's value is still asoc->next_tsn original value minus 1. This patch sets sender next_tsn for the old result with ctsn_ack_point plus 1 when processing the duplicate request, to make sure the sender next_tsn value peer gets will be always right. Fixes: 692787cef651 ("sctp: implement receiver-side procedures for the SSN/TSN Reset Request Parameter") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-28sctp: avoid flushing unsent queue when doing asoc resetXin Long1-7/+14
Now when doing asoc reset, it cleans up sacked and abandoned queues by calling sctp_outq_free where it also cleans up unsent, retransmit and transmitted queues. It's safe for the sender of response, as these 3 queues are empty at that time. But when the receiver of response is doing the reset, the users may already enqueue some chunks into unsent during the time waiting the response, and these chunks should not be flushed. To void the chunks in it would be removed, it moves the queue into a temp list, then gets it back after sctp_outq_free is done. The patch also fixes some incorrect comments in sctp_process_strreset_tsnreq. Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-28sctp: only allow the asoc reset when the asoc outq is emptyXin Long1-0/+9
As it says in rfc6525#section5.1.4, before sending the request, C2: The sender has either no outstanding TSNs or considers all outstanding TSNs abandoned. Prior to this patch, it tried to consider all outstanding TSNs abandoned by dropping all chunks in all outqs with sctp_outq_free (even including sacked, retransmit and transmitted queues) when doing this reset, which is too aggressive. To make it work gently, this patch will only allow the asoc reset when the sender has no outstanding TSNs by checking if unsent, transmitted and retransmit are all empty with sctp_outq_is_empty before sending and processing the request. Fixes: 692787cef651 ("sctp: implement receiver-side procedures for the SSN/TSN Reset Request Parameter") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-28sctp: only allow the out stream reset when the stream outq is emptyXin Long1-0/+35
Now the out stream reset in sctp stream reconf could be done even if the stream outq is not empty. It means that users can not be sure since which msg the new ssn will be used. To make this more synchronous, it shouldn't allow to do out stream reset until these chunks in unsent outq all are sent out. This patch checks the corresponding stream outqs when sending and processing the request . If any of them has unsent chunks in outq, it will return -EAGAIN instead or send SCTP_STRRESET_IN_PROGRESS back to the sender. Fixes: 7f9d68ac944e ("sctp: implement sender-side procedures for SSN Reset Request Parameter") Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-28sctp: use sizeof(__u16) for each stream number length instead of magic numberXin Long1-4/+6
Now in stream reconf part there are still some places using magic number 2 for each stream number length. To make it more readable, this patch is to replace them with sizeof(__u16). Reported-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-27mac80211: tear down RX aggregations firstSara Sharon1-1/+3
When doing HW restart we tear down aggregations. Since at this point we are not TX'ing any aggregation, while the peer is still sending RX aggregation over the air, it will make sense to tear down the RX aggregations first. Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-11-27mac80211: fix the update of path metric for RANN frameChun-Yeow Yeoh1-6/+9
The previous path metric update from RANN frame has not considered the own link metric toward the transmitting mesh STA. Fix this. Reported-by: Michael65535 Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-11-27mac80211: use QoS NDP for AP probingJohannes Berg2-3/+28
When connected to a QoS/WMM AP, mac80211 should use a QoS NDP for probing it, instead of a regular non-QoS one, fix this. Change all the drivers to *not* allow QoS NDP for now, even though it looks like most of them should be OK with that. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-11-26openvswitch: fix the incorrect flow action alloc sizezhangliping1-8/+8
If we want to add a datapath flow, which has more than 500 vxlan outputs' action, we will get the following error reports: openvswitch: netlink: Flow action size 32832 bytes exceeds max openvswitch: netlink: Flow action size 32832 bytes exceeds max openvswitch: netlink: Actions may not be safe on all matching packets ... ... It seems that we can simply enlarge the MAX_ACTIONS_BUFSIZE to fix it, but this is not the root cause. For example, for a vxlan output action, we need about 60 bytes for the nlattr, but after it is converted to the flow action, it only occupies 24 bytes. This means that we can still support more than 1000 vxlan output actions for a single datapath flow under the the current 32k max limitation. So even if the nla_len(attr) is larger than MAX_ACTIONS_BUFSIZE, we shouldn't report EINVAL and keep it move on, as the judgement can be done by the reserve_sfa_size. Signed-off-by: zhangliping <zhangliping02@baidu.com> Acked-by: Pravin B Shelar <pshelar@ovn.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-27net: openvswitch: datapath: fix data type in queue_gso_packetsGustavo A. R. Silva1-1/+1
gso_type is being used in binary AND operations together with SKB_GSO_UDP. The issue is that variable gso_type is of type unsigned short and SKB_GSO_UDP expands to more than 16 bits: SKB_GSO_UDP = 1 << 16 this makes any binary AND operation between gso_type and SKB_GSO_UDP to be always zero, hence making some code unreachable and likely causing undesired behavior. Fix this by changing the data type of variable gso_type to unsigned int. Addresses-Coverity-ID: 1462223 Fixes: 0c19f846d582 ("net: accept UFO datagrams from tuntap and packet") Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-26net: dsa: fix 'increment on 0' warningVivien Didelot1-11/+14
Setting the refcount to 0 when allocating a tree to match the number of switch devices it holds may cause an 'increment on 0; use-after-free', if CONFIG_REFCOUNT_FULL is enabled. To fix this, do not decrement the refcount of a newly allocated tree, increment it when an already allocated tree is found, and decrement it after the probing of a switch, as done with the previous behavior. At the same time, make dsa_tree_get and dsa_tree_put accept a NULL argument to simplify callers, and return the tree after incrementation, as most kref users like of_node_get and of_node_put do. Fixes: 8e5bf9759a06 ("net: dsa: simplify tree reference counting") Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Tested-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-26VSOCK: Don't call vsock_stream_has_data in atomic contextJorgen Hansen1-3/+7
When using the host personality, VMCI will grab a mutex for any queue pair access. In the detach callback for the vmci vsock transport, we call vsock_stream_has_data while holding a spinlock, and vsock_stream_has_data will access a queue pair. To avoid this, we can simply omit calling vsock_stream_has_data for host side queue pairs, since the QPs are empty per default when the guest has detached. This bug affects users of VMware Workstation using kernel version 4.4 and later. Testing: Ran vsock tests between guest and host, and verified that with this change, the host isn't calling vsock_stream_has_data during detach. Ran mixedTest between guest and host using both guest and host as server. v2: Rebased on top of recent change to sk_state values Reviewed-by: Adit Ranadive <aditr@vmware.com> Reviewed-by: Aditya Sarwade <asarwade@vmware.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Jorgen Hansen <jhansen@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-25Merge branch 'timers-urgent-for-linus' of ↵Linus Torvalds42-184/+163
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull timer updates from Thomas Gleixner: - The final conversion of timer wheel timers to timer_setup(). A few manual conversions and a large coccinelle assisted sweep and the removal of the old initialization mechanisms and the related code. - Remove the now unused VSYSCALL update code - Fix permissions of /proc/timer_list. I still need to get rid of that file completely - Rename a misnomed clocksource function and remove a stale declaration * 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits) m68k/macboing: Fix missed timer callback assignment treewide: Remove TIMER_FUNC_TYPE and TIMER_DATA_TYPE casts timer: Remove redundant __setup_timer*() macros timer: Pass function down to initialization routines timer: Remove unused data arguments from macros timer: Switch callback prototype to take struct timer_list * argument timer: Pass timer_list pointer to callbacks unconditionally Coccinelle: Remove setup_timer.cocci timer: Remove setup_*timer() interface timer: Remove init_timer() interface treewide: setup_timer() -> timer_setup() (2 field) treewide: setup_timer() -> timer_setup() treewide: init_timer() -> setup_timer() treewide: Switch DEFINE_TIMER callbacks to struct timer_list * s390: cmm: Convert timers to use timer_setup() lightnvm: Convert timers to use timer_setup() drivers/net: cris: Convert timers to use timer_setup() drm/vc4: Convert timers to use timer_setup() block/laptop_mode: Convert timers to use timer_setup() net/atm/mpc: Avoid open-coded assignment of timer callback function ...
2017-11-25net: sched: crash on blocks with goto chain actionRoman Kapl1-5/+12
tcf_block_put_ext has assumed that all filters (and thus their goto actions) are destroyed in RCU callback and thus can not race with our list iteration. However, that is not true during netns cleanup (see tcf_exts_get_net comment). Prevent the user after free by holding all chains (except 0, that one is already held). foreach_safe is not enough in this case. To reproduce, run the following in a netns and then delete the ns: ip link add dtest type dummy tc qdisc add dev dtest ingress tc filter add dev dtest chain 1 parent ffff: handle 1 prio 1 flower action goto chain 2 Fixes: 822e86d997 ("net_sched: remove tcf_block_put_deferred()") Signed-off-by: Roman Kapl <code@rkapl.cz> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-24cfg80211: select CRYPTO_SHA256 if neededJohannes Berg1-0/+7
When regulatory database certificates are built-in, they're currently using the SHA256 digest algorithm, so add that to the build in that case. Also add a note that for custom certificates, one may need to add the right algorithms. Reported-by: Florian Fainelli <f.fainelli@gmail.com> Tested-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-11-24rxrpc: Fix conn expiry timersDavid Howells5-28/+68
Fix the rxrpc connection expiry timers so that connections for closed AF_RXRPC sockets get deleted in a more timely fashion, freeing up the transport UDP port much more quickly. (1) Replace the delayed work items with work items plus timers so that timer_reduce() can be used to shorten them and so that the timer doesn't requeue the work item if the net namespace is dead. (2) Don't use queue_delayed_work() as that won't alter the timeout if the timer is already running. (3) Don't rearm the timers if the network namespace is dead. Signed-off-by: David Howells <dhowells@redhat.com>
2017-11-24rxrpc: Fix service endpoint expiryDavid Howells5-18/+45
RxRPC service endpoints expire like they're supposed to by the following means: (1) Mark dead rxrpc_net structs (with ->live) rather than twiddling the global service conn timeout, otherwise the first rxrpc_net struct to die will cause connections on all others to expire immediately from then on. (2) Mark local service endpoints for which the socket has been closed (->service_closed) so that the expiration timeout can be much shortened for service and client connections going through that endpoint. (3) rxrpc_put_service_conn() needs to schedule the reaper when the usage count reaches 1, not 0, as idle conns have a 1 count. (4) The accumulator for the earliest time we might want to schedule for should be initialised to jiffies + MAX_JIFFY_OFFSET, not ULONG_MAX as the comparison functions use signed arithmetic. (5) Simplify the expiration handling, adding the expiration value to the idle timestamp each time rather than keeping track of the time in the past before which the idle timestamp must go to be expired. This is much easier to read. (6) Ignore the timeouts if the net namespace is dead. (7) Restart the service reaper work item rather the client reaper. Signed-off-by: David Howells <dhowells@redhat.com>
2017-11-24rxrpc: Add keepalive for a callDavid Howells3-0/+34
We need to transmit a packet every so often to act as a keepalive for the peer (which has a timeout from the last time it received a packet) and also to prevent any intervening firewalls from closing the route. Do this by resetting a timer every time we transmit a packet. If the timer ever expires, we transmit a PING ACK packet and thereby also elicit a PING RESPONSE ACK from the other side - which prevents our last-rx timeout from expiring. The timer is set to 1/6 of the last-rx timeout so that we can detect the other side going away if it misses 6 replies in a row. This is particularly necessary for servers where the processing of the service function may take a significant amount of time. Signed-off-by: David Howells <dhowells@redhat.com>
2017-11-24rxrpc: Add a timeout for detecting lost ACKs/lost DATADavid Howells7-10/+89
Add an extra timeout that is set/updated when we send a DATA packet that has the request-ack flag set. This allows us to detect if we don't get an ACK in response to the latest flagged packet. The ACK packet is adjudged to have been lost if it doesn't turn up within 2*RTT of the transmission. If the timeout occurs, we schedule the sending of a PING ACK to find out the state of the other side. If a new DATA packet is ready to go sooner, we cancel the sending of the ping and set the request-ack flag on that instead. If we get back a PING-RESPONSE ACK that indicates a lower tx_top than what we had at the time of the ping transmission, we adjudge all the DATA packets sent between the response tx_top and the ping-time tx_top to have been lost and retransmit immediately. Rather than sending a PING ACK, we could just pick a DATA packet and speculatively retransmit that with request-ack set. It should result in either a REQUESTED ACK or a DUPLICATE ACK which we can then use in lieu the a PING-RESPONSE ACK mentioned above. Signed-off-by: David Howells <dhowells@redhat.com>
2017-11-24rxrpc: Express protocol timeouts in terms of RTTDavid Howells2-4/+25
Express protocol timeouts for data retransmission and deferred ack generation in terms on RTT rather than specified timeouts once we have sufficient RTT samples. For the moment, this requires just one RTT sample to be able to use this for ack deferral and two for data retransmission. The data retransmission timeout is set at RTT*1.5 and the ACK deferral timeout is set at RTT. Note that the calculated timeout is limited to a minimum of 4ns to make sure it doesn't happen too quickly. Signed-off-by: David Howells <dhowells@redhat.com>
2017-11-24rxrpc: Don't transmit DELAY ACKs immediately on proposalDavid Howells1-2/+2
Don't transmit a DELAY ACK immediately on proposal when the Rx window is rotated, but rather defer it to the work function. This means that we have a chance to queue/consume more received packets before we actually send the DELAY ACK, or even cancel it entirely, thereby reducing the number of packets transmitted. We do, however, want to continue sending other types of packet immediately, particularly REQUESTED ACKs, as they may be used for RTT calculation by the other side. Signed-off-by: David Howells <dhowells@redhat.com>
2017-11-24rxrpc: Fix call timeoutsDavid Howells9-179/+242
Fix the rxrpc call expiration timeouts and make them settable from userspace. By analogy with other rx implementations, there should be three timeouts: (1) "Normal timeout" This is set for all calls and is triggered if we haven't received any packets from the peer in a while. It is measured from the last time we received any packet on that call. This is not reset by any connection packets (such as CHALLENGE/RESPONSE packets). If a service operation takes a long time, the server should generate PING ACKs at a duration that's substantially less than the normal timeout so is to keep both sides alive. This is set at 1/6 of normal timeout. (2) "Idle timeout" This is set only for a service call and is triggered if we stop receiving the DATA packets that comprise the request data. It is measured from the last time we received a DATA packet. (3) "Hard timeout" This can be set for a call and specified the maximum lifetime of that call. It should not be specified by default. Some operations (such as volume transfer) take a long time. Allow userspace to set/change the timeouts on a call with sendmsg, using a control message: RXRPC_SET_CALL_TIMEOUTS The data to the message is a number of 32-bit words, not all of which need be given: u32 hard_timeout; /* sec from first packet */ u32 idle_timeout; /* msec from packet Rx */ u32 normal_timeout; /* msec from data Rx */ This can be set in combination with any other sendmsg() that affects a call. Signed-off-by: David Howells <dhowells@redhat.com>
2017-11-24rxrpc: Split the call params from the operation paramsDavid Howells4-45/+60
When rxrpc_sendmsg() parses the control message buffer, it places the parameters extracted into a structure, but lumps together call parameters (such as user call ID) with operation parameters (such as whether to send data, send an abort or accept a call). Split the call parameters out into their own structure, a copy of which is then embedded in the operation parameters struct. The call parameters struct is then passed down into the places that need it instead of passing the individual parameters. This allows for extra call parameters to be added. Signed-off-by: David Howells <dhowells@redhat.com>
2017-11-24rxrpc: Delay terminal ACK transmission on a client callDavid Howells5-13/+108
Delay terminal ACK transmission on a client call by deferring it to the connection processor. This allows it to be skipped if we can send the next call instead, the first DATA packet of which will implicitly ack this call. Signed-off-by: David Howells <dhowells@redhat.com>
2017-11-24rxrpc: Provide a different lockdep key for call->user_mutex for kernel callsDavid Howells3-6/+17
Provide a different lockdep key for rxrpc_call::user_mutex when the call is made on a kernel socket, such as by the AFS filesystem. The problem is that lockdep registers a false positive between userspace calling the sendmsg syscall on a user socket where call->user_mutex is held whilst userspace memory is accessed whereas the AFS filesystem may perform operations with mmap_sem held by the caller. In such a case, the following warning is produced. ====================================================== WARNING: possible circular locking dependency detected 4.14.0-fscache+ #243 Tainted: G E ------------------------------------------------------ modpost/16701 is trying to acquire lock: (&vnode->io_lock){+.+.}, at: [<ffffffffa000fc40>] afs_begin_vnode_operation+0x33/0x77 [kafs] but task is already holding lock: (&mm->mmap_sem){++++}, at: [<ffffffff8104376a>] __do_page_fault+0x1ef/0x486 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #3 (&mm->mmap_sem){++++}: __might_fault+0x61/0x89 _copy_from_iter_full+0x40/0x1fa rxrpc_send_data+0x8dc/0xff3 rxrpc_do_sendmsg+0x62f/0x6a1 rxrpc_sendmsg+0x166/0x1b7 sock_sendmsg+0x2d/0x39 ___sys_sendmsg+0x1ad/0x22b __sys_sendmsg+0x41/0x62 do_syscall_64+0x89/0x1be return_from_SYSCALL_64+0x0/0x75 -> #2 (&call->user_mutex){+.+.}: __mutex_lock+0x86/0x7d2 rxrpc_new_client_call+0x378/0x80e rxrpc_kernel_begin_call+0xf3/0x154 afs_make_call+0x195/0x454 [kafs] afs_vl_get_capabilities+0x193/0x198 [kafs] afs_vl_lookup_vldb+0x5f/0x151 [kafs] afs_create_volume+0x2e/0x2f4 [kafs] afs_mount+0x56a/0x8d7 [kafs] mount_fs+0x6a/0x109 vfs_kern_mount+0x67/0x135 do_mount+0x90b/0xb57 SyS_mount+0x72/0x98 do_syscall_64+0x89/0x1be return_from_SYSCALL_64+0x0/0x75 -> #1 (k-sk_lock-AF_RXRPC){+.+.}: lock_sock_nested+0x74/0x8a rxrpc_kernel_begin_call+0x8a/0x154 afs_make_call+0x195/0x454 [kafs] afs_fs_get_capabilities+0x17a/0x17f [kafs] afs_probe_fileserver+0xf7/0x2f0 [kafs] afs_select_fileserver+0x83f/0x903 [kafs] afs_fetch_status+0x89/0x11d [kafs] afs_iget+0x16f/0x4f8 [kafs] afs_mount+0x6c6/0x8d7 [kafs] mount_fs+0x6a/0x109 vfs_kern_mount+0x67/0x135 do_mount+0x90b/0xb57 SyS_mount+0x72/0x98 do_syscall_64+0x89/0x1be return_from_SYSCALL_64+0x0/0x75 -> #0 (&vnode->io_lock){+.+.}: lock_acquire+0x174/0x19f __mutex_lock+0x86/0x7d2 afs_begin_vnode_operation+0x33/0x77 [kafs] afs_fetch_data+0x80/0x12a [kafs] afs_readpages+0x314/0x405 [kafs] __do_page_cache_readahead+0x203/0x2ba filemap_fault+0x179/0x54d __do_fault+0x17/0x60 __handle_mm_fault+0x6d7/0x95c handle_mm_fault+0x24e/0x2a3 __do_page_fault+0x301/0x486 do_page_fault+0x236/0x259 page_fault+0x22/0x30 __clear_user+0x3d/0x60 padzero+0x1c/0x2b load_elf_binary+0x785/0xdc7 search_binary_handler+0x81/0x1ff do_execveat_common.isra.14+0x600/0x888 do_execve+0x1f/0x21 SyS_execve+0x28/0x2f do_syscall_64+0x89/0x1be return_from_SYSCALL_64+0x0/0x75 other info that might help us debug this: Chain exists of: &vnode->io_lock --> &call->user_mutex --> &mm->mmap_sem Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&mm->mmap_sem); lock(&call->user_mutex); lock(&mm->mmap_sem); lock(&vnode->io_lock); *** DEADLOCK *** 1 lock held by modpost/16701: #0: (&mm->mmap_sem){++++}, at: [<ffffffff8104376a>] __do_page_fault+0x1ef/0x486 stack backtrace: CPU: 0 PID: 16701 Comm: modpost Tainted: G E 4.14.0-fscache+ #243 Hardware name: ASUS All Series/H97-PLUS, BIOS 2306 10/09/2014 Call Trace: dump_stack+0x67/0x8e print_circular_bug+0x341/0x34f check_prev_add+0x11f/0x5d4 ? add_lock_to_list.isra.12+0x8b/0x8b ? add_lock_to_list.isra.12+0x8b/0x8b ? __lock_acquire+0xf77/0x10b4 __lock_acquire+0xf77/0x10b4 lock_acquire+0x174/0x19f ? afs_begin_vnode_operation+0x33/0x77 [kafs] __mutex_lock+0x86/0x7d2 ? afs_begin_vnode_operation+0x33/0x77 [kafs] ? afs_begin_vnode_operation+0x33/0x77 [kafs] ? afs_begin_vnode_operation+0x33/0x77 [kafs] afs_begin_vnode_operation+0x33/0x77 [kafs] afs_fetch_data+0x80/0x12a [kafs] afs_readpages+0x314/0x405 [kafs] __do_page_cache_readahead+0x203/0x2ba ? filemap_fault+0x179/0x54d filemap_fault+0x179/0x54d __do_fault+0x17/0x60 __handle_mm_fault+0x6d7/0x95c handle_mm_fault+0x24e/0x2a3 __do_page_fault+0x301/0x486 do_page_fault+0x236/0x259 page_fault+0x22/0x30 RIP: 0010:__clear_user+0x3d/0x60 RSP: 0018:ffff880071e93da0 EFLAGS: 00010202 RAX: 0000000000000000 RBX: 000000000000011c RCX: 000000000000011c RDX: 0000000000000000 RSI: 0000000000000008 RDI: 000000000060f720 RBP: 000000000060f720 R08: 0000000000000001 R09: 0000000000000000 R10: 0000000000000001 R11: ffff8800b5459b68 R12: ffff8800ce150e00 R13: 000000000060f720 R14: 00000000006127a8 R15: 0000000000000000 padzero+0x1c/0x2b load_elf_binary+0x785/0xdc7 search_binary_handler+0x81/0x1ff do_execveat_common.isra.14+0x600/0x888 do_execve+0x1f/0x21 SyS_execve+0x28/0x2f do_syscall_64+0x89/0x1be entry_SYSCALL64_slow_path+0x25/0x25 RIP: 0033:0x7fdb6009ee07 RSP: 002b:00007fff566d9728 EFLAGS: 00000246 ORIG_RAX: 000000000000003b RAX: ffffffffffffffda RBX: 000055ba57280900 RCX: 00007fdb6009ee07 RDX: 000055ba5727f270 RSI: 000055ba5727cac0 RDI: 000055ba57280900 RBP: 000055ba57280900 R08: 00007fff566d9700 R09: 0000000000000000 R10: 000055ba5727cac0 R11: 0000000000000246 R12: 0000000000000000 R13: 000055ba5727cac0 R14: 000055ba5727f270 R15: 0000000000000000 Signed-off-by: David Howells <dhowells@redhat.com>
2017-11-24rxrpc: Don't set upgrade by default in sendmsg()David Howells1-1/+1
Don't set upgrade by default when creating a call from sendmsg(). This is a holdover from when I was testing the code. Signed-off-by: David Howells <dhowells@redhat.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-28 19:56:32 +0000