| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The neighbour code sends up an RTM_NEWNEIGH netlink notification if
the NUD state of a neighbour cache entry is changed by a timer (e.g.
from REACHABLE to STALE), even if the lladdr of the entry has not
changed.
But an administrative change to the the NUD state of a neighbour cache
entry that does not change the lladdr (e.g. via "ip -4 neigh change
... nud ...") does not trigger a netlink notification. This means
that netlink listeners will not hear about administrative NUD state
changes such as from a resolved state to PERMANENT.
This patch changes the neighbor code to generate an RTM_NEWNEIGH
message when the NUD state of an entry is changed administratively.
Signed-off-by: Bob Gilligan <gilligan@aristanetworks.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
The following patchset contains two Netfilter fixes for your net
tree, they are:
* Fix endianness in nft_reject, the NFTA_REJECT_TYPE netlink attributes
was not converted to network byte order as needed by all nfnetlink
subsystems, from Eric Leblond.
* Restrict SYNPROXY target to INPUT and FORWARD chains, this avoid a
possible crash due to misconfigurations, from Patrick McHardy.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is similar to the set_peek_off patch where calling bind while the
socket is stuck in unix_dgram_recvmsg() will block and cause a hung task
spew after a while.
This is also the last place that did a straightforward mutex_lock(), so
there shouldn't be any more of these patches.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using sk_dst_lock from softirq context is not supported right now.
Instead of adding BH protection everywhere,
udp_sk_rx_dst_set() can instead use xchg(), as suggested
by David.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Fixes: 975022310233 ("udp: ipv4: must add synchronization in udp_sk_rx_dst_set()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
when I modprobe sctp_probe, it failed with "FATAL: ". I found that
sctp should load before sctp_probe register jprobe. So I add a
sctp_setup_jprobe for loading 'sctp' when first failed to register
jprobe, just do this similar to dccp_probe.
v2: add MODULE_SOFTDEP and check of request_module, as suggested by Neil
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Revert CHECKSUM_COMPLETE optimization in pskb_trim_rcsum(), I can't
figure out why it breaks things.
2) Fix comparison in netfilter ipset's hash_netnet4_data_equal(), it
was basically doing "x == x", from Dave Jones.
3) Freescale FEC driver was DMA mapping the wrong number of bytes, from
Sebastian Siewior.
4) Blackhole and prohibit routes in ipv6 were not doing the right thing
because their ->input and ->output methods were not being assigned
correctly. Now they behave properly like their ipv4 counterparts.
From Kamala R.
5) Several drivers advertise the NETIF_F_FRAGLIST capability, but
really do not support this feature and will send garbage packets if
fed fraglist SKBs. From Eric Dumazet.
6) Fix long standing user triggerable BUG_ON over loopback in RDS
protocol stack, from Venkat Venkatsubra.
7) Several not so common code paths can potentially try to invoke
packet scheduler actions that might be NULL without checking. Shore
things up by either 1) defining a method as mandatory and erroring
on registration if that method is NULL 2) defininig a method as
optional and the registration function hooks up a default
implementation when NULL is seen. From Jamal Hadi Salim.
8) Fix fragment detection in xen-natback driver, from Paul Durrant.
9) Kill dangling enter_memory_pressure method in cg_proto ops, from
Eric W Biederman.
10) SKBs that traverse namespaces should have their local_df cleared,
from Hannes Frederic Sowa.
11) IOCB file position is not being updated by macvtap_aio_read() and
tun_chr_aio_read(). From Zhi Yong Wu.
12) Don't free virtio_net netdev before releasing all of the NAPI
instances. From Andrey Vagin.
13) Procfs entry leak in xt_hashlimit, from Sergey Popovich.
14) IPv6 routes that are no cached routes should not count against the
garbage collection limits. We had this almost right, but were
missing handling addrconf generated routes properly. From Hannes
Frederic Sowa.
15) fib{4,6}_rule_suppress() have to consider potentially seeing NULL
route info when they are called, from Stefan Tomanek.
16) TUN and MACVTAP have had truncated packet signalling for some time,
fix from Jason Wang.
17) Fix use after frrr in __udp4_lib_rcv(), from Eric Dumazet.
18) xen-netback does not interpret the NAPI budget properly for TX work,
fix from Paul Durrant.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (132 commits)
igb: Fix for issue where values could be too high for udelay function.
i40e: fix null dereference
xen-netback: fix gso_prefix check
net: make neigh_priv_len in struct net_device 16bit instead of 8bit
drivers: net: cpsw: fix for cpsw crash when build as modules
xen-netback: napi: don't prematurely request a tx event
xen-netback: napi: fix abuse of budget
sch_tbf: use do_div() for 64-bit divide
udp: ipv4: must add synchronization in udp_sk_rx_dst_set()
net:fec: remove duplicate lines in comment about errata ERR006358
Revert "8390 : Replace ei_debug with msg_enable/NETIF_MSG_* feature"
8390 : Replace ei_debug with msg_enable/NETIF_MSG_* feature
xen-netback: make sure skb linear area covers checksum field
net: smc91x: Fix device tree based configuration so it's usable
udp: ipv4: fix potential use after free in udp_v4_early_demux()
macvtap: signal truncated packets
tun: unbreak truncated packet signalling
net: sched: htb: fix the calculation of quantum
net: sched: tbf: fix the calculation of max_size
micrel: add support for KSZ8041RNLI
...
|
|
The dump function in nft_reject_ipv4 was not converting a u32
field to network order before sending it to userspace, this
needs to happen for consistency with other nf_tables and
nfnetlink subsystems.
Signed-off-by: Eric Leblond <eric@regit.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
It's doing a 64-bit divide which is not supported
on 32-bit architectures in psched_ns_t2l(). The
correct way to do this is to use do_div().
It's introduced by commit cc106e441a63
("net: sched: tbf: fix the calculation of max_size")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Unlike TCP, UDP input path does not hold the socket lock.
Before messing with sk->sk_rx_dst, we must use a spinlock, otherwise
multiple cpus could leak a refcount.
This patch also takes care of renewing a stale dst entry.
(When the sk->sk_rx_dst would not be used by IP early demux)
Fixes: 421b3885bf6d ("udp: ipv4: Add udp early demux")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
pskb_may_pull() can reallocate skb->head, we need to move the
initialization of iph and uh pointers after its call.
Fixes: 421b3885bf6d ("udp: ipv4: Add udp early demux")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now, 32bit rates may be not the true rate.
So use rate_bytes_ps which is from
max(rate32, rate64) to calcualte quantum.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current max_size is caluated from rate table. Now, the rate table
has been replaced and it's wrong to caculate max_size based on this
rate table. It can lead wrong calculation of max_size.
The burst in kernel may be lower than user asked, because burst may gets
some loss when transform it to buffer(E.g. "burst 40kb rate 30mbit/s")
and it seems we cannot avoid this loss. Burst's value(max_size) based on
rate table may be equal user asked. If a packet's length is max_size, this
packet will be stalled in tbf_dequeue() because its length is above the
burst in kernel so that it cannot get enough tokens. The max_size guards
against enqueuing packet sizes above q->buffer "time" in tbf_enqueue().
To make consistent with the calculation of tokens, this patch add a helper
psched_ns_t2l() to calculate burst(max_size) directly to fix this problem.
After this fix, we can support to using 64bit rates to calculate burst as well.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix a crash in synproxy_send_tcp() when using the SYNPROXY target in the
PREROUTING chain caused by missing routing information.
Reported-by: Nicki P. <xastx@gmx.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Dave Jones reported a use after free in UDP stack :
[ 5059.434216] =========================
[ 5059.434314] [ BUG: held lock freed! ]
[ 5059.434420] 3.13.0-rc3+ #9 Not tainted
[ 5059.434520] -------------------------
[ 5059.434620] named/863 is freeing memory ffff88005e960000-ffff88005e96061f, with a lock still held there!
[ 5059.434815] (slock-AF_INET){+.-...}, at: [<ffffffff8149bd21>] udp_queue_rcv_skb+0xd1/0x4b0
[ 5059.435012] 3 locks held by named/863:
[ 5059.435086] #0: (rcu_read_lock){.+.+..}, at: [<ffffffff8143054d>] __netif_receive_skb_core+0x11d/0x940
[ 5059.435295] #1: (rcu_read_lock){.+.+..}, at: [<ffffffff81467a5e>] ip_local_deliver_finish+0x3e/0x410
[ 5059.435500] #2: (slock-AF_INET){+.-...}, at: [<ffffffff8149bd21>] udp_queue_rcv_skb+0xd1/0x4b0
[ 5059.435734]
stack backtrace:
[ 5059.435858] CPU: 0 PID: 863 Comm: named Not tainted 3.13.0-rc3+ #9 [loadavg: 0.21 0.06 0.06 1/115 1365]
[ 5059.436052] Hardware name: /D510MO, BIOS MOPNV10J.86A.0175.2010.0308.0620 03/08/2010
[ 5059.436223] 0000000000000002 ffff88007e203ad8 ffffffff8153a372 ffff8800677130e0
[ 5059.436390] ffff88007e203b10 ffffffff8108cafa ffff88005e960000 ffff88007b00cfc0
[ 5059.436554] ffffea00017a5800 ffffffff8141c490 0000000000000246 ffff88007e203b48
[ 5059.436718] Call Trace:
[ 5059.436769] <IRQ> [<ffffffff8153a372>] dump_stack+0x4d/0x66
[ 5059.436904] [<ffffffff8108cafa>] debug_check_no_locks_freed+0x15a/0x160
[ 5059.437037] [<ffffffff8141c490>] ? __sk_free+0x110/0x230
[ 5059.437147] [<ffffffff8112da2a>] kmem_cache_free+0x6a/0x150
[ 5059.437260] [<ffffffff8141c490>] __sk_free+0x110/0x230
[ 5059.437364] [<ffffffff8141c5c9>] sk_free+0x19/0x20
[ 5059.437463] [<ffffffff8141cb25>] sock_edemux+0x25/0x40
[ 5059.437567] [<ffffffff8141c181>] sock_queue_rcv_skb+0x81/0x280
[ 5059.437685] [<ffffffff8149bd21>] ? udp_queue_rcv_skb+0xd1/0x4b0
[ 5059.437805] [<ffffffff81499c82>] __udp_queue_rcv_skb+0x42/0x240
[ 5059.437925] [<ffffffff81541d25>] ? _raw_spin_lock+0x65/0x70
[ 5059.438038] [<ffffffff8149bebb>] udp_queue_rcv_skb+0x26b/0x4b0
[ 5059.438155] [<ffffffff8149c712>] __udp4_lib_rcv+0x152/0xb00
[ 5059.438269] [<ffffffff8149d7f5>] udp_rcv+0x15/0x20
[ 5059.438367] [<ffffffff81467b2f>] ip_local_deliver_finish+0x10f/0x410
[ 5059.438492] [<ffffffff81467a5e>] ? ip_local_deliver_finish+0x3e/0x410
[ 5059.438621] [<ffffffff81468653>] ip_local_deliver+0x43/0x80
[ 5059.438733] [<ffffffff81467f70>] ip_rcv_finish+0x140/0x5a0
[ 5059.438843] [<ffffffff81468926>] ip_rcv+0x296/0x3f0
[ 5059.438945] [<ffffffff81430b72>] __netif_receive_skb_core+0x742/0x940
[ 5059.439074] [<ffffffff8143054d>] ? __netif_receive_skb_core+0x11d/0x940
[ 5059.442231] [<ffffffff8108c81d>] ? trace_hardirqs_on+0xd/0x10
[ 5059.442231] [<ffffffff81430d83>] __netif_receive_skb+0x13/0x60
[ 5059.442231] [<ffffffff81431c1e>] netif_receive_skb+0x1e/0x1f0
[ 5059.442231] [<ffffffff814334e0>] napi_gro_receive+0x70/0xa0
[ 5059.442231] [<ffffffffa01de426>] rtl8169_poll+0x166/0x700 [r8169]
[ 5059.442231] [<ffffffff81432bc9>] net_rx_action+0x129/0x1e0
[ 5059.442231] [<ffffffff810478cd>] __do_softirq+0xed/0x240
[ 5059.442231] [<ffffffff81047e25>] irq_exit+0x125/0x140
[ 5059.442231] [<ffffffff81004241>] do_IRQ+0x51/0xc0
[ 5059.442231] [<ffffffff81542bef>] common_interrupt+0x6f/0x6f
We need to keep a reference on the socket, by using skb_steal_sock()
at the right place.
Note that another patch is needed to fix a race in
udp_sk_rx_dst_set(), as we hold no lock protecting the dst.
Fixes: 421b3885bf6d ("udp: ipv4: Add udp early demux")
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
fix up spacing of proc_sctp_do_hmac_alg for according to the
proc_sctp_do_rto_min[max] in sysctl.c
Suggested-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rto_min should be smaller than rto_max while rto_max should be larger
than rto_min. Add two proc_handler for the checking.
Suggested-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we set 0 to rto_min or rto_max, just not change the value. Also
we should check the rto_min > rto_max.
Suggested-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is following b579035ff766c9412e2b92abf5cab794bff102b6
"ipv6: remove old conditions on flow label sharing"
Since there is no reason to restrict a label to a
destination, we should not erase the destination value of a
socket with the value contained in the flow label storage.
This patch allows to really have the same flow label to more
than one destination.
Signed-off-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, sctp associations latch a sockets autoclose value to an association
at association init time, subject to capping constraints from the max_autoclose
sysctl value. This leads to an odd situation where an application may set a
socket level autoclose timeout, but sliently sctp will limit the autoclose
timeout to something less than that.
Fix this by modifying the autoclose setsockopt function to check the limit, cap
it and warn the user via syslog that the timeout is capped. This will allow
getsockopt to return valid autoclose timeout values that reflect what subsequent
associations actually use.
While were at it, also elimintate the assoc->autoclose variable, it duplicates
whats in the timeout array, which leads to multiple sources for the same
information, that may differ (as the former isn't subject to any capping). This
gives us the timeout information in a canonical place and saves some space in
the association structure as well.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
CC: Wang Weidong <wangweidong1@huawei.com>
CC: David Miller <davem@davemloft.net>
CC: Vlad Yasevich <vyasevich@gmail.com>
CC: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'handler_enabled' is a global flag indicating whether the TIPC
signal handling service is enabled or not. The lack of lock
protection for this flag incurs a risk for contention, so that
a tipc_k_signal() call might queue a signal handler to a destroyed
signal queue, with unpredictable results. To correct this, we let
the already existing 'qitem_lock' protect the flag, as it already
does with the queue itself. This way, we ensure that the flag
always is consistent across all cores.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 'signal handler' service in TIPC is a mechanism that makes it
possible to postpone execution of functions, by launcing them into
a job queue for execution in a separate tasklet, independent of
the launching execution thread.
When we do rmmod on the tipc module, this service is stopped after
the network service. At the same time, the stopping of the network
service may itself launch jobs for execution, with the risk that these
functions may be scheduled for execution after the data structures
meant to be accessed by the job have already been deleted. We have
seen this happen, most often resulting in an oops.
This commit ensures that the signal handler is the very first to be
stopped when TIPC is shut down, so there are no surprises during
the cleanup of the other services.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
unix_dgram_recvmsg() will hold the readlock of the socket until recv
is complete.
In the same time, we may try to setsockopt(SO_PEEK_OFF) which will hang until
unix_dgram_recvmsg() will complete (which can take a while) without allowing
us to break out of it, triggering a hung task spew.
Instead, allow set_peek_off to fail, this way userspace will not hang.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This changes ensures that the routing entry investigated by the suppress
function actually does point to a device struct before following that pointer,
fixing a possible kernel oops situation when verifying the interface group
associated with a routing table entry.
According to Daniel Golle, this Oops can be triggered by a user process trying
to establish an outgoing IPv6 connection while having no real IPv6 connectivity
set up (only autoassigned link-local addresses).
Fixes: 6ef94cfafba15 ("fib_rules: add route suppression based on ifgroup")
Reported-by: Daniel Golle <daniel.golle@gmail.com>
Tested-by: Daniel Golle <daniel.golle@gmail.com>
Signed-off-by: Stefan Tomanek <stefan.tomanek@wertarbyte.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
maxattr in genl_family should be used to save the max attribute
type, but not the max command type. Drop monitor doesn't support
any attributes, so we should leave it as zero.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Brett Ciphery reported that new ipv6 addresses failed to get installed
because the addrconf generated dsts where counted against the dst gc
limit. We don't need to count those routes like we currently don't count
administratively added routes.
Because the max_addresses check enforces a limit on unbounded address
generation first in case someone plays with router advertisments, we
are still safe here.
Reported-by: Brett Ciphery <brett.ciphery@windriver.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
The following patchset contains three Netfilter fixes for your net tree,
they are:
* fix incorrect comparison in the new netnet hash ipset type, from
Dave Jones.
* fix splat in hashlimit due to missing removal of the content of its
proc entry in netnamespaces, from Sergey Popovich.
* fix missing rule flushing operation by table in nf_tables. Table
flushing was already discussed back in October but this got lost and
no patch has hit the tree to address this issue so far, from me.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit e40526cb20b5 introduced a cached dev pointer, that gets
hooked into register_prot_hook(), __unregister_prot_hook() to
update the device used for the send path.
We need to fix this up, as otherwise this will not work with
sockets created with protocol = 0, plus with sll_protocol = 0
passed via sockaddr_ll when doing the bind.
So instead, assign the pointer directly. The compiler can inline
these helper functions automagically.
While at it, also assume the cached dev fast-path as likely(),
and document this variant of socket creation as it seems it is
not widely used (seems not even the author of TX_RING was aware
of that in his reference example [1]). Tested with reproducer
from e40526cb20b5.
[1] http://wiki.ipxwarzone.com/index.php5?title=Linux_packet_mmap#Example
Fixes: e40526cb20b5 ("packet: fix use after free race in send path when dev is released")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Tested-by: Salam Noureddine <noureddine@aristanetworks.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch allows you to atomically remove all rules stored in
a table via the NFT_MSG_DELRULE command. You only need to indicate
the specific table and no chain to flush all rules stored in that
table.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
In (32263dd1b netfilter: xt_hashlimit: fix namespace destroy path)
the hashlimit_net_exit() function is always called right before
hashlimit_mt_destroy() to release netns data. If you use xt_hashlimit
with IPv4 and IPv6 together, this produces the following splat via
netconsole in the netns destroy path:
Pid: 9499, comm: kworker/u:0 Tainted: G WC O 3.2.0-5-netctl-amd64-core2
Call Trace:
[<ffffffff8104708d>] ? warn_slowpath_common+0x78/0x8c
[<ffffffff81047139>] ? warn_slowpath_fmt+0x45/0x4a
[<ffffffff81144a99>] ? remove_proc_entry+0xd8/0x22e
[<ffffffff810ebbaa>] ? kfree+0x5b/0x6c
[<ffffffffa043c501>] ? hashlimit_net_exit+0x45/0x8d [xt_hashlimit]
[<ffffffff8128ab30>] ? ops_exit_list+0x1c/0x44
[<ffffffff8128b28e>] ? cleanup_net+0xf1/0x180
[<ffffffff810369fc>] ? should_resched+0x5/0x23
[<ffffffff8105b8f9>] ? process_one_work+0x161/0x269
[<ffffffff8105aea5>] ? cwq_activate_delayed_work+0x3c/0x48
[<ffffffff8105c8c2>] ? worker_thread+0xc2/0x145
[<ffffffff8105c800>] ? manage_workers.isra.25+0x15b/0x15b
[<ffffffff8105fa01>] ? kthread+0x76/0x7e
[<ffffffff813581f4>] ? kernel_thread_helper+0x4/0x10
[<ffffffff8105f98b>] ? kthread_worker_fn+0x139/0x139
[<ffffffff813581f0>] ? gs_change+0x13/0x13
---[ end trace d8c3cc0ad163ef79 ]---
------------[ cut here ]------------
WARNING: at /usr/src/linux-3.2.52/debian/build/source_netctl/fs/proc/generic.c:849
remove_proc_entry+0x217/0x22e()
Hardware name:
remove_proc_entry: removing non-empty directory 'net/ip6t_hashlimit', leaking at least 'IN-REJECT'
This is due to lack of removal net/ip6t_hashlimit/* entries in
hashlimit_proc_net_exit(), since only IPv4 entries are deleted. Fix
it by always removing the IPv4 and IPv6 entries and their parent
directories in the netns destroy path.
Signed-off-by: Sergey Popovich <popovich_sergei@mail.ru>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
br_stp_rcv() is reached by non-rx_handler path. That means there is no
guarantee that dev is bridge port and therefore simple NULL check of
->rx_handler_data is not enough. There is need to check if dev is really
bridge port and since only rcu read lock is held here, do it by checking
->rx_handler pointer.
Note that synchronize_net() in netdev_rx_handler_unregister() ensures
this approach as valid.
Introduced originally by:
commit f350a0a87374418635689471606454abc7beaa3a
"bridge: use rx_handler_data pointer to store net_bridge_port pointer"
Fixed but not in the best way by:
commit b5ed54e94d324f17c97852296d61a143f01b227a
"bridge: fix RCU races with bridge port"
Reintroduced by:
commit 716ec052d2280d511e10e90ad54a86f5b5d4dcc2
"bridge: fix NULL pointer deref of br_port_get_rcu"
Please apply to stable trees as well. Thanks.
RH bugzilla reference: https://bugzilla.redhat.com/show_bug.cgi?id=1025770
Reported-by: Laine Stump <laine@redhat.com>
Debugged-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We must clear local_df when passing the skb between namespaces as the
packet is not local to the new namespace any more and thus may not get
fragmented by local rules. Fred Templin noticed that other namespaces
do fragment IPv6 packets while forwarding. Instead they should have send
back a PTB.
The same problem should be present when forwarding DF-IPv4 packets
between namespaces.
Reported-by: Templin, Fred L <Fred.L.Templin@boeing.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
kill memcg_tcp_enter_memory_pressure. The only function of
memcg_tcp_enter_memory_pressure was to reduce deal with the
unnecessary abstraction that was tcp_memcontrol. Now that struct
tcp_memcontrol is gone remove this unnecessary function, the
unnecessary function pointer, and modify sk_enter_memory_pressure to
set this field directly, just as sk_leave_memory_pressure cleas this
field directly.
This fixes a small bug I intruduced when killing struct tcp_memcontrol
that caused memcg_tcp_enter_memory_pressure to never be called and
thus failed to ever set cg_proto->memory_pressure.
Remove the cg_proto enter_memory_pressure function as it now serves
no useful purpose.
Don't test cg_proto->memory_presser in sk_leave_memory_pressure before
clearing it. The test was originally there to ensure that the pointer
was non-NULL. Now that cg_proto is not a pointer the pointer does not
matter.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As Michael pointed out that when max_burst is 0, it just disable
max_burst. It declared in rfc6458#section-8.1.24. so add the check
in sctp_transport_burst_limited, when it 0, just do nothing.
Reviewed-by: Daniel Borkmann <dborkman@redhat.com>
Suggested-by: Vlad Yasevich <vyasevich@gmail.com>
Suggested-by: Michael Tuexen <Michael.Tuexen@lurchi.franken.de>
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull NFS client bugfixes from Trond Myklebust:
- Stable fix for a NFSv4.1 delegation and state recovery deadlock
- Stable fix for a loop on irrecoverable errors when returning
delegations
- Fix a 3-way deadlock between layoutreturn, open, and state recovery
- Update the MAINTAINERS file with contact information for Trond
Myklebust
- Close needs to handle NFS4ERR_ADMIN_REVOKED
- Enabling v4.2 should not recompile nfsd and lockd
- Fix a couple of compile warnings
* tag 'nfs-for-3.13-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
nfs: fix do_div() warning by instead using sector_div()
MAINTAINERS: Update contact information for Trond Myklebust
NFSv4.1: Prevent a 3-way deadlock between layoutreturn, open and state recovery
SUNRPC: do not fail gss proc NULL calls with EACCES
NFSv4: close needs to handle NFS4ERR_ADMIN_REVOKED
NFSv4: Update list of irrecoverable errors on DELEGRETURN
NFSv4 wait on recovery for async session errors
NFS: Fix a warning in nfs_setsecurity
NFS: Enabling v4.2 should not recompile nfsd and lockd
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
After congestion update on a local connection, when rds_ib_xmit returns
less bytes than that are there in the message, rds_send_xmit calls
back rds_ib_xmit with an offset that causes BUG_ON(off & RDS_FRAG_SIZE)
to trigger.
For a 4Kb PAGE_SIZE rds_ib_xmit returns min(8240,4096)=4096 when actually
the message contains 8240 bytes. rds_send_xmit thinks there is more to send
and calls rds_ib_xmit again with a data offset "off" of 4096-48(rds header)
=4048 bytes thus hitting the BUG_ON(off & RDS_FRAG_SIZE) [RDS_FRAG_SIZE=4k].
The commit 6094628bfd94323fc1cea05ec2c6affd98c18f7f
"rds: prevent BUG_ON triggering on congestion map updates" introduced
this regression. That change was addressing the triggering of a different
BUG_ON in rds_send_xmit() on PowerPC architecture with 64Kbytes PAGE_SIZE:
BUG_ON(ret != 0 &&
conn->c_xmit_sg == rm->data.op_nents);
This was the sequence it was going through:
(rds_ib_xmit)
/* Do not send cong updates to IB loopback */
if (conn->c_loopback
&& rm->m_inc.i_hdr.h_flags & RDS_FLAG_CONG_BITMAP) {
rds_cong_map_updated(conn->c_fcong, ~(u64) 0);
return sizeof(struct rds_header) + RDS_CONG_MAP_BYTES;
}
rds_ib_xmit returns 8240
rds_send_xmit:
c_xmit_data_off = 0 + 8240 - 48 (rds header accounted only the first time)
= 8192
c_xmit_data_off < 65536 (sg->length), so calls rds_ib_xmit again
rds_ib_xmit returns 8240
rds_send_xmit:
c_xmit_data_off = 8192 + 8240 = 16432, calls rds_ib_xmit again
and so on (c_xmit_data_off 24672,32912,41152,49392,57632)
rds_ib_xmit returns 8240
On this iteration this sequence causes the BUG_ON in rds_send_xmit:
while (ret) {
tmp = min_t(int, ret, sg->length - conn->c_xmit_data_off);
[tmp = 65536 - 57632 = 7904]
conn->c_xmit_data_off += tmp;
[c_xmit_data_off = 57632 + 7904 = 65536]
ret -= tmp;
[ret = 8240 - 7904 = 336]
if (conn->c_xmit_data_off == sg->length) {
conn->c_xmit_data_off = 0;
sg++;
conn->c_xmit_sg++;
BUG_ON(ret != 0 &&
conn->c_xmit_sg == rm->data.op_nents);
[c_xmit_sg = 1, rm->data.op_nents = 1]
What the current fix does:
Since the congestion update over loopback is not actually transmitted
as a message, all that rds_ib_xmit needs to do is let the caller think
the full message has been transmitted and not return partial bytes.
It will return 8240 (RDS_CONG_MAP_BYTES+48) when PAGE_SIZE is 4Kb.
And 64Kb+48 when page size is 64Kb.
Reported-by: Josh Hunt <joshhunt00@gmail.com>
Tested-by: Honggang Li <honli@redhat.com>
Acked-by: Bang Nguyen <bang.nguyen@oracle.com>
Signed-off-by: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The behaviour of blackhole and prohibit routes has been corrected by setting
the input and output pointers of the dst variable appropriately. For
blackhole routes, they are set to dst_discard and to ip6_pkt_discard and
ip6_pkt_discard_out respectively for prohibit routes.
ipv6: ip6_pkt_prohibit(_out) should not depend on
CONFIG_IPV6_MULTIPLE_TABLES
We need ip6_pkt_prohibit(_out) available without
CONFIG_IPV6_MULTIPLE_TABLES
Signed-off-by: Kamala R <kamala@aristanetworks.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Francois-Xavier Le Bail <fx.lebail@yahoo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
when dealing with a RA message, if accept_ra_defrtr is false,
the kernel will not add the default route, and then deal with
the following route information options. Unfortunately, those
options maybe contain default route, so let's judge the
accept_ra_defrtr before calling rt6_route_rcv.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
|
|
Pull networking updates from David Miller:
"Here is a pile of bug fixes that accumulated while I was in Europe"
1) In fixing kernel leaks to userspace during copying of socket
addresses, we broke a case that used to work, namely the user
providing a buffer larger than the in-kernel generic socket address
structure. This broke Ruby amongst other things. Fix from Dan
Carpenter.
2) Fix regression added by byte queue limit support in 8139cp driver,
from Yang Yingliang.
3) The addition of MSG_SENDPAGE_NOTLAST buggered up a few sendpage
implementations, they should just treat it the same as MSG_MORE.
Fix from Richard Weinberger and Shawn Landden.
4) Handle icmpv4 errors received on ipv6 SIT tunnels correctly, from
Oussama Ghorbel. In particular we should send an ICMPv6 unreachable
in such situations.
5) Fix some regressions in the recent genetlink fixes, in particular
get the pmcraid driver to use the new safer interfaces correctly.
From Johannes Berg.
6) macvtap was converted to use a per-cpu set of statistics, but some
code was still bumping tx_dropped elsewhere. From Jason Wang.
7) Fix build failure of xen-netback due to missing include on some
architectures, from Andy Whitecroft.
8) macvtap double counts received packets in statistics, fix from Vlad
Yasevich.
9) Fix various cases of using *_STATS_BH() when *_STATS() is more
appropriate. From Eric Dumazet and Hannes Frederic Sowa.
10) Pktgen ipsec mode doesn't update the ipv4 header length and checksum
properly after encapsulation. Fix from Fan Du.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (61 commits)
net/mlx4_en: Remove selftest TX queues empty condition
{pktgen, xfrm} Update IPv4 header total len and checksum after tranformation
virtio_net: make all RX paths handle erors consistently
virtio_net: fix error handling for mergeable buffers
virtio_net: Fixed a trivial typo (fitler --> filter)
netem: fix gemodel loss generator
netem: fix loss 4 state model
netem: missing break in ge loss generator
net/hsr: Support iproute print_opt ('ip -details ...')
net/hsr: Very small fix of comment style.
MAINTAINERS: Added net/hsr/ maintainer
ipv6: fix possible seqlock deadlock in ip6_finish_output2
ixgbe: Make ixgbe_identify_qsfp_module_generic static
ixgbe: turn NETIF_F_HW_L2FW_DOFFLOAD off by default
ixgbe: ixgbe_fwd_ring_down needs to be static
e1000: fix possible reset_task running after adapter down
e1000: fix lockdep warning in e1000_reset_task
e1000: prevent oops when adapter is being closed and reset simultaneously
igb: Fixed Wake On LAN support
inet: fix possible seqlock deadlocks
...
|
|
When external CSA IEs are received (beacons or action messages), a
channel switch is triggered as well. This should only be allowed on
devices which actually support channel switches, otherwise disconnect.
(For the corresponding userspace invocation, the wiphy flag is checked
in nl80211).
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The channel switch announcement code has some major locking problems
which can cause a deadlock in worst case. A series of fixes has been
proposed, but these are non-trivial and need to be tested first.
Therefore disable CSA completely for 3.13.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
commit a553e4a6317b2cfc7659542c10fe43184ffe53da ("[PKTGEN]: IPSEC support")
tried to support IPsec ESP transport transformation for pktgen, but acctually
this doesn't work at all for two reasons(The orignal transformed packet has
bad IPv4 checksum value, as well as wrong auth value, reported by wireshark)
- After transpormation, IPv4 header total length needs update,
because encrypted payload's length is NOT same as that of plain text.
- After transformation, IPv4 checksum needs re-caculate because of payload
has been changed.
With this patch, armmed pktgen with below cofiguration, Wireshark is able to
decrypted ESP packet generated by pktgen without any IPv4 checksum error or
auth value error.
pgset "flag IPSEC"
pgset "flows 1"
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Patch from developers of the alternative loss models, downloaded from:
http://netgroup.uniroma2.it/twiki/bin/view.cgi/Main/NetemCLG
"in case 2, of the switch we change the direction of the inequality to
net_random()>clg->a3, because clg->a3 is h in the GE model and when h
is 0 all packets will be lost."
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
