| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull networking fixes from David Miller:
1) Two read past end of buffer fixes in AF_KEY, from Eric Biggers.
2) Memory leak in key_notify_policy(), from Steffen Klassert.
3) Fix overflow with bpf arrays, from Daniel Borkmann.
4) Fix RDMA regression with mlx5 due to mlx5 no longer using
pci_irq_get_affinity(), from Saeed Mahameed.
5) Missing RCU read locking in nl80211_send_iface() when it calls
ieee80211_bss_get_ie(), from Dominik Brodowski.
6) cfg80211 should check dev_set_name()'s return value, from Johannes
Berg.
7) Missing module license tag in 9p protocol, from Stephen Hemminger.
8) Fix crash due to too small MTU in udp ipv6 sendmsg, from Mike
Maloney.
9) Fix endless loop in netlink extack code, from David Ahern.
10) TLS socket layer sets inverted error codes, resulting in an endless
loop. From Robert Hering.
11) Revert openvswitch erspan tunnel support, it's mis-designed and we
need to kill it before it goes into a real release. From William Tu.
12) Fix lan78xx failures in full speed USB mode, from Yuiko Oshino.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (54 commits)
net, sched: fix panic when updating miniq {b,q}stats
qed: Fix potential use-after-free in qed_spq_post()
nfp: use the correct index for link speed table
lan78xx: Fix failure in USB Full Speed
sctp: do not allow the v4 socket to bind a v4mapped v6 address
sctp: return error if the asoc has been peeled off in sctp_wait_for_sndbuf
sctp: reinit stream if stream outcnt has been change by sinit in sendmsg
ibmvnic: Fix pending MAC address changes
netlink: extack: avoid parenthesized string constant warning
ipv4: Make neigh lookup keys for loopback/point-to-point devices be INADDR_ANY
net: Allow neigh contructor functions ability to modify the primary_key
sh_eth: fix dumping ARSTR
Revert "openvswitch: Add erspan tunnel support."
net/tls: Fix inverted error codes to avoid endless loop
ipv6: ip6_make_skb() needs to clear cork.base.dst
sctp: avoid compiler warning on implicit fallthru
net: ipv4: Make "ip route get" match iif lo rules again.
netlink: extack needs to be reset each time through loop
tipc: fix a memory leak in tipc_nl_node_get_link()
ipv6: fix udpv6 sendmsg crash caused by too small MTU
...
|
|
While working on fixing another bug, I ran into the following panic
on arm64 by simply attaching clsact qdisc, adding a filter and running
traffic on ingress to it:
[...]
[ 178.188591] Unable to handle kernel read from unreadable memory at virtual address 810fb501f000
[ 178.197314] Mem abort info:
[ 178.200121] ESR = 0x96000004
[ 178.203168] Exception class = DABT (current EL), IL = 32 bits
[ 178.209095] SET = 0, FnV = 0
[ 178.212157] EA = 0, S1PTW = 0
[ 178.215288] Data abort info:
[ 178.218175] ISV = 0, ISS = 0x00000004
[ 178.222019] CM = 0, WnR = 0
[ 178.224997] user pgtable: 4k pages, 48-bit VAs, pgd = 0000000023cb3f33
[ 178.231531] [0000810fb501f000] *pgd=0000000000000000
[ 178.236508] Internal error: Oops: 96000004 [#1] SMP
[...]
[ 178.311855] CPU: 73 PID: 2497 Comm: ping Tainted: G W 4.15.0-rc7+ #5
[ 178.319413] Hardware name: FOXCONN R2-1221R-A4/C2U4N_MB, BIOS G31FB18A 03/31/2017
[ 178.326887] pstate: 60400005 (nZCv daif +PAN -UAO)
[ 178.331685] pc : __netif_receive_skb_core+0x49c/0xac8
[ 178.336728] lr : __netif_receive_skb+0x28/0x78
[ 178.341161] sp : ffff00002344b750
[ 178.344465] x29: ffff00002344b750 x28: ffff810fbdfd0580
[ 178.349769] x27: 0000000000000000 x26: ffff000009378000
[...]
[ 178.418715] x1 : 0000000000000054 x0 : 0000000000000000
[ 178.424020] Process ping (pid: 2497, stack limit = 0x000000009f0a3ff4)
[ 178.430537] Call trace:
[ 178.432976] __netif_receive_skb_core+0x49c/0xac8
[ 178.437670] __netif_receive_skb+0x28/0x78
[ 178.441757] process_backlog+0x9c/0x160
[ 178.445584] net_rx_action+0x2f8/0x3f0
[...]
Reason is that sch_ingress and sch_clsact are doing mini_qdisc_pair_init()
which sets up miniq pointers to cpu_{b,q}stats from the underlying qdisc.
Problem is that this cannot work since they are actually set up right after
the qdisc ->init() callback in qdisc_create(), so first packet going into
sch_handle_ingress() tries to call mini_qdisc_bstats_cpu_update() and we
therefore panic.
In order to fix this, allocation of {b,q}stats needs to happen before we
call into ->init(). In net-next, there's already such option through commit
d59f5ffa59d8 ("net: sched: a dflt qdisc may be used with per cpu stats").
However, the bug needs to be fixed in net still for 4.15. Thus, include
these bits to reduce any merge churn and reuse the static_flags field to
set TCQ_F_CPUSTATS, and remove the allocation from qdisc_create() since
there is no other user left. Prashant Bhole ran into the same issue but
for net-next, thus adding him below as well as co-author. Same issue was
also reported by Sandipan Das when using bcc.
Fixes: 46209401f8f6 ("net: core: introduce mini_Qdisc and eliminate usage of tp->q for clsact fastpath")
Reference: https://lists.iovisor.org/pipermail/iovisor-dev/2018-January/001190.html
Reported-by: Sandipan Das <sandipan@linux.vnet.ibm.com>
Co-authored-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Co-authored-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
More fixes:
* hwsim:
- properly flush deletion works at module unload
- validate # of channels passed from userspace
* cfg80211:
- fix RCU locking regression
- initialize on-stack channel data for nl80211 event
- check dev_set_name() return value
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The check in sctp_sockaddr_af is not robust enough to forbid binding a
v4mapped v6 addr on a v4 socket.
The worse thing is that v4 socket's bind_verify would not convert this
v4mapped v6 addr to a v4 addr. syzbot even reported a crash as the v4
socket bound a v6 addr.
This patch is to fix it by doing the common sa.sa_family check first,
then AF_INET check for v4mapped v6 addrs.
Fixes: 7dab83de50c7 ("sctp: Support ipv6only AF_INET6 sockets.")
Reported-by: syzbot+7b7b518b1228d2743963@syzkaller.appspotmail.com
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After commit cea0cc80a677 ("sctp: use the right sk after waking up from
wait_buf sleep"), it may change to lock another sk if the asoc has been
peeled off in sctp_wait_for_sndbuf.
However, the asoc's new sk could be already closed elsewhere, as it's in
the sendmsg context of the old sk that can't avoid the new sk's closing.
If the sk's last one refcnt is held by this asoc, later on after putting
this asoc, the new sk will be freed, while under it's own lock.
This patch is to revert that commit, but fix the old issue by returning
error under the old sk's lock.
Fixes: cea0cc80a677 ("sctp: use the right sk after waking up from wait_buf sleep")
Reported-by: syzbot+ac6ea7baa4432811eb50@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After introducing sctp_stream structure, sctp uses stream->outcnt as the
out stream nums instead of c.sinit_num_ostreams.
However when users use sinit in cmsg, it only updates c.sinit_num_ostreams
in sctp_sendmsg. At that moment, stream->outcnt is still using previous
value. If it's value is not updated, the sinit_num_ostreams of sinit could
not really work.
This patch is to fix it by updating stream->outcnt and reiniting stream
if stream outcnt has been change by sinit in sendmsg.
Fixes: a83863174a61 ("sctp: prepare asoc stream for stream reconf")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Map all lookup neigh keys to INADDR_ANY for loopback/point-to-point devices
to avoid making an entry for every remote ip the device needs to talk to.
This used the be the old behavior but became broken in a263b3093641f
(ipv4: Make neigh lookups directly in output packet path) and later removed
in 0bb4087cbec0 (ipv4: Fix neigh lookup keying over loopback/point-to-point
devices) because it was broken.
Signed-off-by: Jim Westfall <jwestfall@surrealistic.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use n->primary_key instead of pkey to account for the possibility that a neigh
constructor function may have modified the primary_key value.
Signed-off-by: Jim Westfall <jwestfall@surrealistic.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit ceaa001a170e43608854d5290a48064f57b565ed.
The OVS_TUNNEL_KEY_ATTR_ERSPAN_OPTS attr should be designed
as a nested attribute to support all ERSPAN v1 and v2's fields.
The current attr is a be32 supporting only one field. Thus, this
patch reverts it and later patch will redo it using nested attr.
Signed-off-by: William Tu <u9012063@gmail.com>
Cc: Jiri Benc <jbenc@redhat.com>
Cc: Pravin Shelar <pshelar@ovn.org>
Acked-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sendfile() calls can hang endless with using Kernel TLS if a socket error occurs.
Socket error codes must be inverted by Kernel TLS before returning because
they are stored with positive sign. If returned non-inverted they are
interpreted as number of bytes sent, causing endless looping of the
splice mechanic behind sendfile().
Signed-off-by: Robert Hering <r.hering@avm.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In my last patch, I missed fact that cork.base.dst was not initialized
in ip6_make_skb() :
If ip6_setup_cork() returns an error, we might attempt a dst_release()
on some random pointer.
Fixes: 862c03ee1deb ("ipv6: fix possible mem leaks in ipv6_make_skb()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These fall-through are expected.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 3765d35ed8b9 ("net: ipv4: Convert inet_rtm_getroute to rcu
versions of route lookup") broke "ip route get" in the presence
of rules that specify iif lo.
Host-originated traffic always has iif lo, because
ip_route_output_key_hash and ip6_route_output_flags set the flow
iif to LOOPBACK_IFINDEX. Thus, putting "iif lo" in an ip rule is a
convenient way to select only originated traffic and not forwarded
traffic.
inet_rtm_getroute used to match these rules correctly because
even though it sets the flow iif to 0, it called
ip_route_output_key which overwrites iif with LOOPBACK_IFINDEX.
But now that it calls ip_route_output_key_hash_rcu, the ifindex
will remain 0 and not match the iif lo in the rule. As a result,
"ip route get" will return ENETUNREACH.
Fixes: 3765d35ed8b9 ("net: ipv4: Convert inet_rtm_getroute to rcu versions of route lookup")
Tested: https://android.googlesource.com/kernel/tests/+/master/net/test/multinetwork_test.py passes again
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzbot triggered the WARN_ON in netlink_ack testing the bad_attr value.
The problem is that netlink_rcv_skb loops over the skb repeatedly invoking
the callback and without resetting the extack leaving potentially stale
data. Initializing each time through avoids the WARN_ON.
Fixes: 2d4bc93368f5a ("netlink: extended ACK reporting")
Reported-by: syzbot+315fa6766d0f7c359327@syzkaller.appspotmail.com
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When tipc_node_find_by_name() fails, the nlmsg is not
freed.
While on it, switch to a goto label to properly
free it.
Fixes: be9c086715c ("tipc: narrow down exposure of struct tipc_node")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The logic in __ip6_append_data() assumes that the MTU is at least large
enough for the headers. A device's MTU may be adjusted after being
added while sendmsg() is processing data, resulting in
__ip6_append_data() seeing any MTU. For an mtu smaller than the size of
the fragmentation header, the math results in a negative 'maxfraglen',
which causes problems when refragmenting any previous skb in the
skb_write_queue, leaving it possibly malformed.
Instead sendmsg returns EINVAL when the mtu is calculated to be less
than IPV6_MIN_MTU.
Found by syzkaller:
kernel BUG at ./include/linux/skbuff.h:2064!
invalid opcode: 0000 [#1] SMP KASAN
Dumping ftrace buffer:
(ftrace buffer empty)
Modules linked in:
CPU: 1 PID: 14216 Comm: syz-executor5 Not tainted 4.13.0-rc4+ #2
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
task: ffff8801d0b68580 task.stack: ffff8801ac6b8000
RIP: 0010:__skb_pull include/linux/skbuff.h:2064 [inline]
RIP: 0010:__ip6_make_skb+0x18cf/0x1f70 net/ipv6/ip6_output.c:1617
RSP: 0018:ffff8801ac6bf570 EFLAGS: 00010216
RAX: 0000000000010000 RBX: 0000000000000028 RCX: ffffc90003cce000
RDX: 00000000000001b8 RSI: ffffffff839df06f RDI: ffff8801d9478ca0
RBP: ffff8801ac6bf780 R08: ffff8801cc3f1dbc R09: 0000000000000000
R10: ffff8801ac6bf7a0 R11: 43cb4b7b1948a9e7 R12: ffff8801cc3f1dc8
R13: ffff8801cc3f1d40 R14: 0000000000001036 R15: dffffc0000000000
FS: 00007f43d740c700(0000) GS:ffff8801dc100000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f7834984000 CR3: 00000001d79b9000 CR4: 00000000001406e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
ip6_finish_skb include/net/ipv6.h:911 [inline]
udp_v6_push_pending_frames+0x255/0x390 net/ipv6/udp.c:1093
udpv6_sendmsg+0x280d/0x31a0 net/ipv6/udp.c:1363
inet_sendmsg+0x11f/0x5e0 net/ipv4/af_inet.c:762
sock_sendmsg_nosec net/socket.c:633 [inline]
sock_sendmsg+0xca/0x110 net/socket.c:643
SYSC_sendto+0x352/0x5a0 net/socket.c:1750
SyS_sendto+0x40/0x50 net/socket.c:1718
entry_SYSCALL_64_fastpath+0x1f/0xbe
RIP: 0033:0x4512e9
RSP: 002b:00007f43d740bc08 EFLAGS: 00000216 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 00000000007180a8 RCX: 00000000004512e9
RDX: 000000000000002e RSI: 0000000020d08000 RDI: 0000000000000005
RBP: 0000000000000086 R08: 00000000209c1000 R09: 000000000000001c
R10: 0000000000040800 R11: 0000000000000216 R12: 00000000004b9c69
R13: 00000000ffffffff R14: 0000000000000005 R15: 00000000202c2000
Code: 9e 01 fe e9 c5 e8 ff ff e8 7f 9e 01 fe e9 4a ea ff ff 48 89 f7 e8 52 9e 01 fe e9 aa eb ff ff e8 a8 b6 cf fd 0f 0b e8 a1 b6 cf fd <0f> 0b 49 8d 45 78 4d 8d 45 7c 48 89 85 78 fe ff ff 49 8d 85 ba
RIP: __skb_pull include/linux/skbuff.h:2064 [inline] RSP: ffff8801ac6bf570
RIP: __ip6_make_skb+0x18cf/0x1f70 net/ipv6/ip6_output.c:1617 RSP: ffff8801ac6bf570
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Mike Maloney <maloney@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 9P of Xen module is missing required license and module information.
See https://bugzilla.kernel.org/show_bug.cgi?id=198109
Reported-by: Alan Bartlett <ajb@elrepo.org>
Fixes: 868eb122739a ("xen/9pfs: introduce Xen 9pfs transport driver")
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzbot reported a warning from rfkill_alloc(), and after a while
I think that the reason is that it was doing fault injection and
the dev_set_name() failed, leaving the name NULL, and we didn't
check the return value and got to rfkill_alloc() with a NULL name.
Since we really don't want a NULL name, we ought to check the
return value.
Fixes: fb28ad35906a ("net: struct device - replace bus_id with dev_name(), dev_set_name()")
Reported-by: syzbot+1ddfb3357e1d7bb5b5d3@syzkaller.appspotmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When creating a new radio on the fly, hwsim allows this
to be done with an arbitrary number of channels, but
cfg80211 only supports a limited number of simultaneous
channels, leading to a warning.
Fix this by validating the number - this requires moving
the define for the maximum out to a visible header file.
Reported-by: syzbot+8dd9051ff19940290931@syzkaller.appspotmail.com
Fixes: b59ec8dd4394 ("mac80211_hwsim: fix number of channels in interface combinations")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
As ieee80211_bss_get_ie() derefences an RCU to return ssid_ie, both
the call to this function and any operation on this variable need
protection by the RCU read lock.
Fixes: 44905265bc15 ("nl80211: don't expose wdev->ssid for most interfaces")
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Paul reported that he got a report about undefined behaviour
that seems to me to originate in using uninitialized memory
when the channel structure here is used in the event code in
nl80211 later.
He never reported whether this fixed it, and I wasn't able
to trigger this so far, but we should do the right thing and
fully initialize the on-stack structure anyway.
Reported-by: Paul Menzel <pmenzel+linux-wireless@molgen.mpg.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fixes from Greg KH:
"Here are two bugfixes for some driver bugs for 4.15-rc8
The first is a bluetooth security bug that has been ignored by the
Bluetooth developers for months for no obvious reason at all, so I've
taken it through my tree.
The second is a simple double-free bug in the mux subsystem.
Both have been in linux-next for a while with no reported issues"
* tag 'char-misc-4.15-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mux: core: fix double get_device()
Bluetooth: Prevent stack info leak from the EFS element.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
pull request (net): ipsec 2018-01-11
1) Don't allow to change the encap type on state updates.
The encap type is set on state initialization and
should not change anymore. From Herbert Xu.
2) Skip dead policies when rehashing to fix a
slab-out-of-bounds bug in xfrm_hash_rebuild.
From Florian Westphal.
3) Two buffer overread fixes in pfkey.
From Eric Biggers.
4) Fix rcu usage in xfrm_get_type_offload,
request_module can sleep, so can't be used
under rcu_read_lock. From Sabrina Dubroca.
5) Fix an uninitialized lock in xfrm_trans_queue.
Use __skb_queue_tail instead of skb_queue_tail
in xfrm_trans_queue as we don't need the lock.
From Herbert Xu.
6) Currently it is possible to create an xfrm state with an
unknown encap type in ESP IPv4. Fix this by returning an
error on unknown encap types. Also from Herbert Xu.
7) Fix sleeping inside a spinlock in xfrm_policy_cache_flush.
From Florian Westphal.
8) Fix ESP GRO when the headers not fully in the linear part
of the skb. We need to pull before we can access them.
9) Fix a skb leak on error in key_notify_policy.
10) Fix a race in the xdst pcpu cache, we need to
run the resolver routines with bottom halfes
off like the old flowcache did.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs regression fix from Al Viro/
Fix a leak in socket() introduced by commit 8e1611e23579 ("make
sock_alloc_file() do sock_release() on failures").
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
Fix a leak in socket(2) when we fail to allocate a file descriptor.
|
|
Got broken by "make sock_alloc_file() do sock_release() on failures" -
cleanup after sock_map_fd() failure got pulled all the way into
sock_alloc_file(), but it used to serve the case when sock_map_fd()
failed *before* getting to sock_alloc_file() as well, and that got
lost. Trivial to fix, fortunately.
Fixes: 8e1611e23579 (make sock_alloc_file() do sock_release() on failures)
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Function ipv6_push_rthdr4 allows to add an IPv6 Segment Routing Header
to a socket through setsockopt, but the current implementation doesn't
copy possible TLVs at the end of the SRH received from userspace.
Therefore, the execution of the following branch if (sr_has_hmac(sr_phdr))
{ ... } will never complete since the len and type fields of a possible
HMAC TLV are not copied, hence seg6_get_tlv_hmac will return an error,
and the HMAC will not be computed.
This commit adds a memcpy in case TLVs have been appended to the SRH.
Fixes: a149e7c7ce81 ("ipv6: sr: add support for SRH injection through setsockopt")
Acked-by: David Lebrun <dlebrun@google.com>
Signed-off-by: Mathieu Xhonneux <m.xhonneux@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ip6_setup_cork() might return an error, while memory allocations have
been done and must be rolled back.
Fixes: 6422398c2ab0 ("ipv6: introduce ipv6_make_skb")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Reported-by: Mike Maloney <maloney@google.com>
Acked-by: Mike Maloney <maloney@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A vlan device with vid 0 is allow to creat by not able to be fully
cleaned up by unregister_vlan_dev() which checks for vlan_id!=0.
Also, VLAN 0 is probably not a valid number and it is kinda
"reserved" for HW accelerating devices, but it is probably too
late to reject it from creation even if makes sense. Instead,
just remove the check in unregister_vlan_dev().
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Fixes: ad1afb003939 ("vlan_dev: VLAN 0 should be treated as "no vlan tag" (802.1p packet)")
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gcc-8 reports
net/caif/caif_usb.c: In function 'cfusbl_device_notify':
./include/linux/string.h:245:9: warning: '__builtin_strncpy' output may
be truncated copying 15 bytes from a string of length 15
[-Wstringop-truncation]
The compiler require that the input param 'len' of strncpy() should be
greater than the length of the src string, so that '\0' is copied as
well. We can just use strlcpy() to avoid this warning.
Signed-off-by: Xiongfeng Wang <xiongfeng.wang@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some sockopt handling functions were calculating the length of the
buffer to be written to userspace and then calculating it again when
actually writing the buffer, which could lead to some write not using
an up-to-date length.
This patch updates such places to just make use of the len variable.
Also, replace some sizeof(type) to sizeof(var).
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hangbin Liu reported that some sockopt calls could cause the kernel to log
a warning on memory allocation failure if the user supplied a large optlen
value. That is because some of them called memdup_user() without a ceiling
on optlen, allowing it to try to allocate really large buffers.
This patch adds a ceiling by limiting optlen to the maximum allowed that
would still make sense for these sockopt.
Reported-by: Hangbin Liu <haliu@redhat.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
So replace it with GFP_USER and also add __GFP_NOWARN.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel Borkmann says:
====================
pull-request: bpf 2018-01-09
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Prevent out-of-bounds speculation in BPF maps by masking the
index after bounds checks in order to fix spectre v1, and
add an option BPF_JIT_ALWAYS_ON into Kconfig that allows for
removing the BPF interpreter from the kernel in favor of
JIT-only mode to make spectre v2 harder, from Alexei.
2) Remove false sharing of map refcount with max_entries which
was used in spectre v1, from Daniel.
3) Add a missing NULL psock check in sockmap in order to fix
a race, from John.
4) Fix test_align BPF selftest case since a recent change in
verifier rejects the bit-wise arithmetic on pointers
earlier but test_align update was missing, from Alexei.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to run xfrm_resolve_and_create_bundle() with
bottom halves off. Otherwise we may reuse an already
released dst_enty when the xfrm lookup functions are
called from process context.
Fixes: c30d78c14a813db39a647b6a348b428 ("xfrm: add xdst pcpu cache")
Reported-by: Darius Ski <darius.ski@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
We leak the allocated out_skb in case
pfkey_xfrm_policy2msg() fails. Fix this
by freeing it on error.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
The BPF interpreter has been used as part of the spectre 2 attack CVE-2017-5715.
A quote from goolge project zero blog:
"At this point, it would normally be necessary to locate gadgets in
the host kernel code that can be used to actually leak data by reading
from an attacker-controlled location, shifting and masking the result
appropriately and then using the result of that as offset to an
attacker-controlled address for a load. But piecing gadgets together
and figuring out which ones work in a speculation context seems annoying.
So instead, we decided to use the eBPF interpreter, which is built into
the host kernel - while there is no legitimate way to invoke it from inside
a VM, the presence of the code in the host kernel's text section is sufficient
to make it usable for the attack, just like with ordinary ROP gadgets."
To make attacker job harder introduce BPF_JIT_ALWAYS_ON config
option that removes interpreter from the kernel in favor of JIT-only mode.
So far eBPF JIT is supported by:
x64, arm64, arm32, sparc64, s390, powerpc64, mips64
The start of JITed program is randomized and code page is marked as read-only.
In addition "constant blinding" can be turned on with net.core.bpf_jit_harden
v2->v3:
- move __bpf_prog_ret0 under ifdef (Daniel)
v1->v2:
- fix init order, test_bpf and cBPF (Daniel's feedback)
- fix offloaded bpf (Jakub's feedback)
- add 'return 0' dummy in case something can invoke prog->bpf_func
- retarget bpf tree. For bpf-next the patch would need one extra hunk.
It will be sent when the trees are merged back to net-next
Considered doing:
int bpf_jit_enable __read_mostly = BPF_EBPF_JIT_DEFAULT;
but it seems better to land the patch as-is and in bpf-next remove
bpf_jit_enable global variable from all JITs, consolidate in one place
and remove this jit_init() function.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
In the current code, when creating a new fib6 table, tb6_root.leaf gets
initialized to net->ipv6.ip6_null_entry.
If a default route is being added with rt->rt6i_metric = 0xffffffff,
fib6_add() will add this route after net->ipv6.ip6_null_entry. As
null_entry is shared, it could cause problem.
In order to fix it, set fn->leaf to NULL before calling
fib6_add_rt2node() when trying to add the first default route.
And reset fn->leaf to null_entry when adding fails or when deleting the
last default route.
syzkaller reported the following issue which is fixed by this commit:
WARNING: suspicious RCU usage
4.15.0-rc5+ #171 Not tainted
-----------------------------
net/ipv6/ip6_fib.c:1702 suspicious rcu_dereference_protected() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
4 locks held by swapper/0/0:
#0: ((&net->ipv6.ip6_fib_timer)){+.-.}, at: [<00000000d43f631b>] lockdep_copy_map include/linux/lockdep.h:178 [inline]
#0: ((&net->ipv6.ip6_fib_timer)){+.-.}, at: [<00000000d43f631b>] call_timer_fn+0x1c6/0x820 kernel/time/timer.c:1310
#1: (&(&net->ipv6.fib6_gc_lock)->rlock){+.-.}, at: [<000000002ff9d65c>] spin_lock_bh include/linux/spinlock.h:315 [inline]
#1: (&(&net->ipv6.fib6_gc_lock)->rlock){+.-.}, at: [<000000002ff9d65c>] fib6_run_gc+0x9d/0x3c0 net/ipv6/ip6_fib.c:2007
#2: (rcu_read_lock){....}, at: [<0000000091db762d>] __fib6_clean_all+0x0/0x3a0 net/ipv6/ip6_fib.c:1560
#3: (&(&tb->tb6_lock)->rlock){+.-.}, at: [<000000009e503581>] spin_lock_bh include/linux/spinlock.h:315 [inline]
#3: (&(&tb->tb6_lock)->rlock){+.-.}, at: [<000000009e503581>] __fib6_clean_all+0x1d0/0x3a0 net/ipv6/ip6_fib.c:1948
stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.15.0-rc5+ #171
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:17 [inline]
dump_stack+0x194/0x257 lib/dump_stack.c:53
lockdep_rcu_suspicious+0x123/0x170 kernel/locking/lockdep.c:4585
fib6_del+0xcaa/0x11b0 net/ipv6/ip6_fib.c:1701
fib6_clean_node+0x3aa/0x4f0 net/ipv6/ip6_fib.c:1892
fib6_walk_continue+0x46c/0x8a0 net/ipv6/ip6_fib.c:1815
fib6_walk+0x91/0xf0 net/ipv6/ip6_fib.c:1863
fib6_clean_tree+0x1e6/0x340 net/ipv6/ip6_fib.c:1933
__fib6_clean_all+0x1f4/0x3a0 net/ipv6/ip6_fib.c:1949
fib6_clean_all net/ipv6/ip6_fib.c:1960 [inline]
fib6_run_gc+0x16b/0x3c0 net/ipv6/ip6_fib.c:2016
fib6_gc_timer_cb+0x20/0x30 net/ipv6/ip6_fib.c:2033
call_timer_fn+0x228/0x820 kernel/time/timer.c:1320
expire_timers kernel/time/timer.c:1357 [inline]
__run_timers+0x7ee/0xb70 kernel/time/timer.c:1660
run_timer_softirq+0x4c/0xb0 kernel/time/timer.c:1686
__do_softirq+0x2d7/0xb85 kernel/softirq.c:285
invoke_softirq kernel/softirq.c:365 [inline]
irq_exit+0x1cc/0x200 kernel/softirq.c:405
exiting_irq arch/x86/include/asm/apic.h:540 [inline]
smp_apic_timer_interrupt+0x16b/0x700 arch/x86/kernel/apic/apic.c:1052
apic_timer_interrupt+0xa9/0xb0 arch/x86/entry/entry_64.S:904
</IRQ>
Reported-by: syzbot <syzkaller@googlegroups.com>
Fixes: 66f5d6ce53e6 ("ipv6: replace rwlock with rcu and spinlock in fib6_table")
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 8f659a03a0ba ("net: ipv4: fix for a race condition in
raw_sendmsg") fixed the issue of possibly inconsistent ->hdrincl handling
due to concurrent updates by reading this bit-field member into a local
variable and using the thus stabilized value in subsequent tests.
However, aforementioned commit also adds the (correct) comment that
/* hdrincl should be READ_ONCE(inet->hdrincl)
* but READ_ONCE() doesn't work with bit fields
*/
because as it stands, the compiler is free to shortcut or even eliminate
the local variable at its will.
Note that I have not seen anything like this happening in reality and thus,
the concern is a theoretical one.
However, in order to be on the safe side, emulate a READ_ONCE() on the
bit-field by doing it on the local 'hdrincl' variable itself:
int hdrincl = inet->hdrincl;
hdrincl = READ_ONCE(hdrincl);
This breaks the chain in the sense that the compiler is not allowed
to replace subsequent reads from hdrincl with reloads from inet->hdrincl.
Fixes: 8f659a03a0ba ("net: ipv4: fix for a race condition in raw_sendmsg")
Signed-off-by: Nicolai Stange <nstange@suse.de>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gcc-8 reports
net/caif/caif_dev.c: In function 'caif_enroll_dev':
./include/linux/string.h:245:9: warning: '__builtin_strncpy' output may
be truncated copying 15 bytes from a string of length 15
[-Wstringop-truncation]
net/caif/cfctrl.c: In function 'cfctrl_linkup_request':
./include/linux/string.h:245:9: warning: '__builtin_strncpy' output may
be truncated copying 15 bytes from a string of length 15
[-Wstringop-truncation]
net/caif/cfcnfg.c: In function 'caif_connect_client':
./include/linux/string.h:245:9: warning: '__builtin_strncpy' output may
be truncated copying 15 bytes from a string of length 15
[-Wstringop-truncation]
The compiler require that the input param 'len' of strncpy() should be
greater than the length of the src string, so that '\0' is copied as
well. We can just use strlcpy() to avoid this warning.
Signed-off-by: Xiongfeng Wang <xiongfeng.wang@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use AF_INET6 instead of AF_INET in IPv6-related code path
Signed-off-by: Andrii Vladyka <tulup@mail.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The GRO layer does not necessarily pull the complete headers
into the linear part of the skb, a part may remain on the
first page fragment. This can lead to a crash if we try to
pull the headers, so make sure we have them on the linear
part before pulling.
Fixes: 7785bba299a8 ("esp: Add a software GRO codepath")
Reported-by: syzbot+82bbd65569c49c6c0c4d@syzkaller.appspotmail.com
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
Pull networking fixes from David Miller:
1) Frag and UDP handling fixes in i40e driver, from Amritha Nambiar and
Alexander Duyck.
2) Undo unintentional UAPI change in netfilter conntrack, from Florian
Westphal.
3) Revert a change to how error codes are returned from
dev_get_valid_name(), it broke some apps.
4) Cannot cache routes for ipv6 tunnels in the tunnel is ipv4/ipv6
dual-stack. From Eli Cooper.
5) Fix missed PMTU updates in geneve, from Xin Long.
6) Cure double free in macvlan, from Gao Feng.
7) Fix heap out-of-bounds write in rds_message_alloc_sgs(), from
Mohamed Ghannam.
8) FEC bug fixes from FUgang Duan (mis-accounting of dev_id, missed
deferral of probe when the regulator is not ready yet).
9) Missing DMA mapping error checks in 3c59x, from Neil Horman.
10) Turn off Broadcom tags for some b53 switches, from Florian Fainelli.
11) Fix OOPS when get_target_net() is passed an SKB whose NETLINK_CB()
isn't initialized. From Andrei Vagin.
12) Fix crashes in fib6_add(), from Wei Wang.
13) PMTU bug fixes in SCTP from Marcelo Ricardo Leitner.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (56 commits)
sh_eth: fix TXALCR1 offsets
mdio-sun4i: Fix a memory leak
phylink: mark expected switch fall-throughs in phylink_mii_ioctl
sctp: fix the handling of ICMP Frag Needed for too small MTUs
sctp: do not retransmit upon FragNeeded if PMTU discovery is disabled
xen-netfront: enable device after manual module load
bnxt_en: Fix the 'Invalid VF' id check in bnxt_vf_ndo_prep routine.
bnxt_en: Fix population of flow_type in bnxt_hwrm_cfa_flow_alloc()
sh_eth: fix SH7757 GEther initialization
net: fec: free/restore resource in related probe error pathes
uapi/if_ether.h: prevent redefinition of struct ethhdr
ipv6: fix general protection fault in fib6_add()
RDS: null pointer dereference in rds_atomic_free_op
sh_eth: fix TSU resource handling
net: stmmac: enable EEE in MII, GMII or RGMII only
rtnetlink: give a user socket to get_target_net()
MAINTAINERS: Update my email address.
can: ems_usb: improve error reporting for error warning and error passive
can: flex_can: Correct the checking for frame length in flexcan_start_xmit()
can: gs_usb: fix return value of the "set_bittiming" callback
...
|
|
syzbot reported a hang involving SCTP, on which it kept flooding dmesg
with the message:
[ 246.742374] sctp: sctp_transport_update_pmtu: Reported pmtu 508 too
low, using default minimum of 512
That happened because whenever SCTP hits an ICMP Frag Needed, it tries
to adjust to the new MTU and triggers an immediate retransmission. But
it didn't consider the fact that MTUs smaller than the SCTP minimum MTU
allowed (512) would not cause the PMTU to change, and issued the
retransmission anyway (thus leading to another ICMP Frag Needed, and so
on).
As IPv4 (ip_rt_min_pmtu=556) and IPv6 (IPV6_MIN_MTU=1280) minimum MTU
are higher than that, sctp_transport_update_pmtu() is changed to
re-fetch the PMTU that got set after our request, and with that, detect
if there was an actual change or not.
The fix, thus, skips the immediate retransmission if the received ICMP
resulted in no change, in the hope that SCTP will select another path.
Note: The value being used for the minimum MTU (512,
SCTP_DEFAULT_MINSEGMENT) is not right and instead it should be (576,
SCTP_MIN_PMTU), but such change belongs to another patch.
Changes from v1:
- do not disable PMTU discovery, in the light of commit
06ad391919b2 ("[SCTP] Don't disable PMTU discovery when mtu is small")
and as suggested by Xin Long.
- changed the way to break the rtx loop by detecting if the icmp
resulted in a change or not
Changes from v2:
none
See-also: https://lkml.org/lkml/2017/12/22/811
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, if PMTU discovery is disabled on a given transport, but the
configured value is higher than the actual PMTU, it is likely that we
will get some icmp Frag Needed. The issue is, if PMTU discovery is
disabled, we won't update the information and will issue a
retransmission immediately, which may very well trigger another ICMP,
and another retransmission, leading to a loop.
The fix is to simply not trigger immediate retransmissions if PMTU
discovery is disabled on the given transport.
Changes from v2:
- updated stale comment, noticed by Xin Long
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
xfrm_policy_cache_flush can sleep, so it cannot be called while holding
a spinlock. We could release the lock first, but I don't see why we need
to invoke this function here in first place, the packet path won't reuse
an xdst entry unless its still valid.
While at it, add an annotation to xfrm_policy_cache_flush, it would
have probably caught this bug sooner.
Fixes: ec30d78c14a813 ("xfrm: add xdst pcpu cache")
Reported-by: syzbot+e149f7d1328c26f9c12f@syzkaller.appspotmail.com
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
Currently esp will happily create an xfrm state with an unknown
encap type for IPv4, without setting the necessary state parameters.
This patch fixes it by returning -EINVAL.
There is a similar problem in IPv6 where if the mode is unknown
we will skip initialisation while returning zero. However, this
is harmless as the mode has already been checked further up the
stack. This patch removes this anomaly by aligning the IPv6
behaviour with IPv4 and treating unknown modes (which cannot
actually happen) as transport mode.
Fixes: 38320c70d282 ("[IPSEC]: Use crypto_aead and authenc in ESP")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
- untangle sys_close() abuses in xt_bpf
- deal with register_shrinker() failures in sget()
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fix "netfilter: xt_bpf: Fix XT_BPF_MODE_FD_PINNED mode of 'xt_bpf_info_v1'"
sget(): handle failures of register_shrinker()
mm,vmscan: Make unregister_shrinker() no-op if register_shrinker() failed.
|
|
Descriptor table is a shared object; it's not a place where you can
stick temporary references to files, especially when we don't need
an opened file at all.
Cc: stable@vger.kernel.org # v4.14
Fixes: 98589a0998b8 ("netfilter: xt_bpf: Fix XT_BPF_MODE_FD_PINNED mode of 'xt_bpf_info_v1'")
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree,
they are:
1) Fix chain filtering when dumping rules via nf_tables_dump_rules().
2) Fix accidental change in NF_CT_STATE_UNTRACKED_BIT through uapi,
introduced when removing the untracked conntrack object, from
Florian Westphal.
3) Fix potential nul-dereference when releasing dump filter in
nf_tables_dump_obj_done(), patch from Hangbin Liu.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We do not need locking in xfrm_trans_queue because it is designed
to use per-CPU buffers. However, the original code incorrectly
used skb_queue_tail which takes the lock. This patch switches
it to __skb_queue_tail instead.
Reported-and-tested-by: Artem Savkov <asavkov@redhat.com>
Fixes: acf568ee859f ("xfrm: Reinject transport-mode packets...")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
