| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Some of the comment blocks are floating in limbo between two
functions, or between blocks of code. Delete the extra line
feeds between any comment and its associated following block
of code, to be consistent with the majority of the rest of
the kernel. Also delete trailing newlines at EOF and fix
a couple trivial typos in existing comments.
This is a 100% cosmetic change with no runtime impact. We get
rid of over 500 lines of non-code, and being blank line deletes,
they won't even show up as noise in git blame.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Adds check to ensure TIPC sockets reject incoming payload messages
that have an unrecognized message type.
Remove the old open question about whether TIPC_ERR_NO_PORT is
the proper return value. It is appropriate here since there are
valid instances where another node can make use of the reply,
and at this point in time the host is already broadcasting TIPC
data, so there are no real security concerns.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Consolidates validation of scope and name sequence range values into
a single routine where it applies both to local name publications
and to name publications issued by other nodes in the network. This
change means that the scope value for non-local publications is now
validated and the name sequence range for local publications is now
validated only once. Additionally, a publication attempt that fails
validation now creates an entry in the system log file only if debugging
capabilities have been enabled; this prevents the system log from being
cluttered up with messages caused by a defective application or network
node.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Replaces two identical chunks of code that delete an unused name
sequence structure from TIPC's name table with calls to a new routine
that performs this operation.
This change is cosmetic and doesn't impact the operation of TIPC.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Eliminate code to zero-out the main topology service structure,
which is already zeroed-out.
Get rid of a comment documenting a field of the main topology
service structure that no longer exists.
Both are cosmetic changes with no impact on runtime behaviour.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Initialization now occurs in the calling thread of control,
rather than being deferred to the TIPC tasklet. With the
current codebase, the deferral is no longer necessary.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Streamlines the job of re-initializing TIPC's network topology service
when a node's network address is first assigned. Rather than destroying
the topology server port and breaking its connections to existing
subscribers, TIPC now simply lets the service continue running (since
the change to the port identifier of each port used by the topology
service no longer impacts the flow of messages between the service and
its subscribers).
This enhancement means that applications that utilize the topology
service prior to the assignment of TIPC's network address no longer need
to re-establish their subscriptions when the address is finally assigned.
However, it is worth noting that any subsequent events for existing
subscriptions report the new port identifier of the publishing port,
rather than the original port identifier. (For example, a name that was
previously reported as being published by <0.0.0:ref> may be subsequently
withdrawn by <Z.C.N:ref>.)
This doesn't impact any of the existing known userspace in tipc-utils,
since (a) TIPC continues to treat references to the original port ID
correctly and (b) normal use cases assign an address before active use.
However if there does happen to be some rare/custom application out
there that was relying on this, they can simply bypass the enhancement
by issuing a subscription to {0,0} and break its connection to the
topology service, if an associated withdrawal event occurs.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Termination no longer tests to see if the configuration service
port was successfully created or not. In the unlikely event that the
port was not created, attempting to delete the non-existent port is
detected gracefully and causes no harm.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Initialization now occurs in the calling thread of control,
rather than being deferred to the TIPC tasklet. With the
current codebase, the deferral is no longer necessary.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Streamlines the job of re-initializing TIPC's configuration service
when a node's network address is first assigned. Rather than destroying
the configuration server port and then recreating it, TIPC now simply
withdraws the existing {0,<0.0.0>} name publication and creates a new
{0,<Z.C.N>} name publication that identifies the node's network address
to interested subscribers.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
read only, so change it to const.
Signed-off-by: Shan Wei <davidshan@tencent.com>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some kfree_skb() calls should be replaced by consume_skb() to avoid
drop_monitor/dropwatch false positives.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds code to trigger CEE events when an APP change or setall
command is made from user space. This simplifies user space code
significantly by creating a single interface to listen on that
works with both firmware and userland agents.
And if we end up with multiple agents this keeps every thing in
sync userland agents, firmware agents, and kernel notifier consumers.
For an example agent that listens for these events see:
https://github.com/jrfastab/cgdcbxd
cgdcbxd is a daemon used to monitor DCB netlink events and manage
the net_prio control group sub-system.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Shmulik Ravid <shmulikr@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Untie gcc's hands and let it do what it wants within the
individual source files. There are two files, node.c and
port.c -- only the latter effectively changes (gcc-4.5.2).
Objdump shows gcc deciding to not inline port_peernode().
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Need to consume_skb() instead of kfree_skb() in netlink_dump() and
netlink_unicast_kernel() to avoid false dropwatch positives.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netlink_destroy_callback() move to avoid forward reference
CodingStyle cleanups
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This clarifies code intention, as suggested by David.
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix merge between commit 3adadc08cc1e ("net ax25: Reorder ax25_exit to
remove races") and commit 0ca7a4c87d27 ("net ax25: Simplify and
cleanup the ax25 sysctl handling")
The former moved around the sysctl register/unregister calls, the
later simply removed them.
With help from Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 35f3d14db (pipe: add support for shrinking and growing pipes)
added a slowdown for splice(socket -> pipe), as we might grow the spd
used in skb_splice_bits() for each skb we process in splice() syscall.
Its not needed since skb lengths are capped. The default on-stack arrays
are more than enough.
Use MAX_SKB_FRAGS instead of PIPE_DEF_BUFFERS to describe the reasonable
limit per skb.
Add coalescing support to help splicing of GRO skbs built from linear
skbs (linked into frag_list)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit c8628155ece3 (tcp: reduce out_of_order memory use) took care of
coalescing tcp segments provided by legacy devices (linear skbs)
We extend this idea to fragged skbs, as their truesize can be heavy.
ixgbe for example uses 256+1024+PAGE_SIZE/2 = 3328 bytes per segment.
Use this coalescing strategy for receive queue too.
This contributes to reduce number of tcp collapses, at minimal cost, and
reduces memory overhead and packets drops.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While investigating TCP performance problems on 10Gb+ links, we found a
tcp sender was dropping lot of incoming ACKS because of sk_rcvbuf limit
in sk_add_backlog(), especially if receiver doesnt use GRO/LRO and sends
one ACK every two MSS segments.
A sender usually tweaks sk_sndbuf, but sk_rcvbuf stays at its default
value (87380), allowing a too small backlog.
A TCP ACK, even being small, can consume nearly same truesize space than
outgoing packets. Using sk_rcvbuf + sk_sndbuf as a limit makes sense and
is fast to compute.
Performance results on netperf, single flow, receiver with disabled
GRO/LRO : 7500 Mbits instead of 6050 Mbits, no more TCPBacklogDrop
increments at sender.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Cc: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sk_add_backlog() & sk_rcvqueues_full() hard coded sk_rcvbuf as the
memory limit. We need to make this limit a parameter for TCP use.
No functional change expected in this patch, all callers still using the
old sk_rcvbuf limit.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Cc: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
net/ipv4/tcp_ipv4.c: In function 'tcp_v4_init_sock':
net/ipv4/tcp_ipv4.c:1891:19: warning: unused variable 'tp' [-Wunused-variable]
net/ipv6/tcp_ipv6.c: In function 'tcp_v6_init_sock':
net/ipv6/tcp_ipv6.c:1836:19: warning: unused variable 'tp' [-Wunused-variable]
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit f5fff5d forgot to fix TCP_MAXSEG behavior IPv6 sockets, so IPv6
TCP server sockets that used TCP_MAXSEG would find that the advmss of
child sockets would be incorrect. This commit mirrors the advmss logic
from tcp_v4_syn_recv_sock in tcp_v6_syn_recv_sock. Eventually this
logic should probably be shared between IPv4 and IPv6, but this at
least fixes this issue.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Factorize code, since most fetched values are int type.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit moves the (substantial) common code shared between
tcp_v4_init_sock() and tcp_v6_init_sock() to a new address-family
independent function, tcp_init_sock().
Centralizing this functionality should help avoid drift issues,
e.g. where the IPv4 side is updated without a corresponding update to
IPv6. There was already some drift: IPv4 initialized snd_cwnd to
TCP_INIT_CWND, while the IPv6 side was still initializing snd_cwnd to
2 (in this case it should not matter, since snd_cwnd is also
initialized in tcp_init_metrics(), but the general risks and
maintenance overhead remain).
When diffing the old and new code, note that new tcp_init_sock()
function uses the order of steps from the tcp_v4_init_sock()
implementation (the order is slightly different in
tcp_v6_init_sock()).
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
splice() from socket to pipe needs linear_to_page() helper to transfert
skb header to part of page.
We can reset the offset in the current sk->sk_sndmsg_page if we are the
last user of the page.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It seems there is a logic error in trace_drop_common(), since we store
only 64 drops, even if they are from same location.
This fix is a one liner, but we probably need more work to avoid useless
atomic dec/inc
Now I can watch 1 Mpps drops through dropwatch...
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
iov of more than 8 entries are allocated in sendmsg()/recvmsg() through
sock_kmalloc()
As these allocations are temporary only and small enough, it makes sense
to use plain kmalloc() and avoid sk_omem_alloc atomic overhead.
Slightly changed fast path to be even faster.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Mike Waychison <mikew@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are options, which are set up on a socket while performing
TCP handshake. Need to resurrect them on a socket while repairing.
A new sockoption accepts a buffer and parses it. The buffer should
be CODE:VALUE sequence of bytes, where CODE is standard option
code and VALUE is the respective value.
Only 4 options should be handled on repaired socket.
To read 3 out of 4 of these options the TCP_INFO sockoption can be
used. An ability to get the last one (the mss_clamp) was added by
the previous patch.
Now the restore. Three of these options -- timestamp_ok, mss_clamp
and snd_wscale -- are just restored on a coket.
The sack_ok flags has 2 issues. First, whether or not to do sacks
at all. This flag is just read and set back. No other sack info is
saved or restored, since according to the standart and the code
dropping all sack-ed segments is OK, the sender will resubmit them
again, so after the repair we will probably experience a pause in
connection. Next, the fack bit. It's just set back on a socket if
the respective sysctl is set. No collected stats about packets flow
is preserved. As far as I see (plz, correct me if I'm wrong) the
fack-based congestion algorithm survives dropping all of the stats
and repairs itself eventually, probably losing the performance for
that period.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mss_clamp is the only connection-time negotiated option which
cannot be obtained from the user space. Make the TCP_MAXSEG sockopt
report one in the repair mode.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reading queues under repair mode is done with recvmsg call.
The queue-under-repair set by TCP_REPAIR_QUEUE option is used
to determine which queue should be read. Thus both send and
receive queue can be read with this.
Caller must pass the MSG_PEEK flag.
Writing to queues is done with sendmsg call and yet again --
the repair-queue option can be used to push data into the
receive queue.
When putting an skb into receive queue a zero tcp header is
appented to its head to address the tcp_hdr(skb)->syn and
the ->fin checks by the (after repair) tcp_recvmsg. These
flags flags are both set to zero and that's why.
The fin cannot be met in the queue while reading the source
socket, since the repair only works for closed/established
sockets and queueing fin packet always changes its state.
The syn in the queue denotes that the respective skb's seq
is "off-by-one" as compared to the actual payload lenght. Thus,
at the rcv queue refill we can just drop this flag and set the
skb's sequences to precice values.
When the repair mode is turned off, the write queue seqs are
updated so that the whole queue is considered to be 'already sent,
waiting for ACKs' (write_seq = snd_nxt <= snd_una). From the
protocol POV the send queue looks like it was sent, but the data
between the write_seq and snd_nxt is lost in the network.
This helps to avoid another sockoption for setting the snd_nxt
sequence. Leaving the whole queue in a 'not yet sent' state (as
it will be after sendmsg-s) will not allow to receive any acks
from the peer since the ack_seq will be after the snd_nxt. Thus
even the ack for the window probe will be dropped and the
connection will be 'locked' with the zero peer window.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This includes (according the the previous description):
* TCP_REPAIR sockoption
This one just puts the socket in/out of the repair mode.
Allowed for CAP_NET_ADMIN and for closed/establised sockets only.
When repair mode is turned off and the socket happens to be in
the established state the window probe is sent to the peer to
'unlock' the connection.
* TCP_REPAIR_QUEUE sockoption
This one sets the queue which we're about to repair. The
'no-queue' is set by default.
* TCP_QUEUE_SEQ socoption
Sets the write_seq/rcv_nxt of a selected repaired queue.
Allowed for TCP_CLOSE-d sockets only. When the socket changes
its state the other seq-s are changed by the kernel according
to the protocol rules (most of the existing code is actually
reused).
* Ability to forcibly bind a socket to a port
The sk->sk_reuse is set to SK_FORCE_REUSE.
* Immediate connect modification
The connect syscall initializes the connection, then directly jumps
to the code which finalizes it.
* Silent close modification
The close just aborts the connection (similar to SO_LINGER with 0
time) but without sending any FIN/RST-s to peer.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is just the preparation patch, which makes the needed for
TCP repair code ready for use.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Name them in a "backward compatible" manner, i.e. reuse or not
are still 1 and 0 respectively. The reuse value of 2 means that
the socket with it will forcibly reuse everyone else's port.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All of the users have been converted to use registera_net_sysctl so we
no longer need register_net_sysctl.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We don't use struct ctl_path anymore so delete the exported constants.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This results in code with less boiler plate that is a bit easier
to read.
Additionally stops us from using compatibility code in the sysctl
core, hastening the day when the compatibility code can be removed.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There isn't much advantage here except that strings paths are a bit
easier to read, and converting everything to them allows me to kill off
ctl_path.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using an ascii path to register_net_sysctl as opposed to the slightly
awkward ctl_path allows for much simpler code.
We no longer need to malloc dev_name to keep it alive the length of our
sysctl register instead we can use a small temporary buffer on the
stack.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using an ascii path to register_net_sysctl as opposed to the slightly
awkward ctl_path allows for much simpler code.
We no longer need to malloc dev_name to keep it alive the length of our
sysctl register instead we can use a small temporary buffer on the
stack.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using an ascii path to register_net_sysctl as opposed to the slightly
awkward ctl_path allows for much simpler code.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using an ascii path to register_net_sysctl as opposed to the slightly
awkward ctl_path allows for much simpler code.
We no longer need to malloc dev_name to keep it alive the length of our
sysctl register instead we can use a small temporary buffer on the
stack.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The sysctl core no longer natively understands sysctl tables
with .child entries.
Split the ipv6_table to remove the .child entries.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The sysctl core no longer natively understands sysctl tables with .child
entries.
Kill the intermediate tables and use register_net_sysctl directly to
remove the need for compatibility code.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't register/unregister every ax25 table in a batch. Instead register
and unregister per device ax25 sysctls as ax25 devices come and go.
This moves ax25 to be a completely modern sysctl user. Registering the
sysctls in just the initial network namespace, removing the use of
.child entries that are no longer natively supported by the sysctl core
and taking advantage of the fact that there are no longer any ordering
constraints between registering and unregistering different sysctl
tables.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sysctl no longer requires explicit creation of directories. The neigh
directory is always populated with at least a default entry so this
won't cause any user visible changes.
Delete the ipv4_path and the ipv4_skeleton these are no longer needed.
Directly register the ipv4_route_table.
And since I am an idiot remove the header definitions that I should
have removed in the previous patch.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
