summaryrefslogtreecommitdiffstats
path: root/net
AgeCommit message (Collapse)AuthorFilesLines
2019-01-27Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds16-74/+120
Pull networking fixes from David Miller: 1) Count ttl-dropped frames properly in mac80211, from Bob Copeland. 2) Integer overflow in ktime handling of bcm can code, from Oliver Hartkopp. 3) Fix RX desc handling wrt. hw checksumming in ravb, from Simon Horman. 4) Various hash key fixes in hv_netvsc, from Haiyang Zhang. 5) Use after free in ax25, from Eric Dumazet. 6) Several fixes to the SSN support in SCTP, from Xin Long. 7) Do not process frames after a NAPI reschedule in ibmveth, from Thomas Falcon. 8) Fix NLA_POLICY_NESTED arguments, from Johannes Berg. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (42 commits) qed: Revert error handling changes. cfg80211: extend range deviation for DMG cfg80211: reg: remove warn_on for a normal case mac80211: Add attribute aligned(2) to struct 'action' mac80211: don't initiate TDLS connection if station is not associated to AP nl80211: fix NLA_POLICY_NESTED() arguments ibmveth: Do not process frames after calling napi_reschedule net: dev_is_mac_header_xmit() true for ARPHRD_RAWIP net: usb: asix: ax88772_bind return error when hw_reset fail MAINTAINERS: Update cavium networking drivers net/mlx4_core: Fix error handling when initializing CQ bufs in the driver net/mlx4_core: Add masking for a few queries on HCA caps sctp: set flow sport from saddr only when it's 0 sctp: set chunk transport correctly when it's a new asoc sctp: improve the events for sctp stream adding sctp: improve the events for sctp stream reset ip_tunnel: Make none-tunnel-dst tunnel port work with lwtunnel ax25: fix possible use-after-free sfc: suppress duplicate nvmem partition types in efx_ef10_mtd_probe hv_netvsc: fix typos in code comments ...
2019-01-25Merge tag 'mac80211-for-davem-2019-01-25' of ↵David S. Miller4-7/+18
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211 Johannes Berg says: ==================== Just a few small fixes: * avoid trying to operate TDLS when not connection, this is not valid and led to issues * count TTL-dropped frames in mesh better * deal with new WiGig channels in regulatory code * remove a WARN_ON() that can trigger due to benign races during device/driver registration * fix nested netlink policy maxattrs (syzkaller) * fix hwsim n_limits (syzkaller) * propagate __aligned(2) to a surrounding struct * return proper error in virt_wifi error path ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-25cfg80211: extend range deviation for DMGChaitanya Tata1-2/+2
Recently, DMG frequency bands have been extended till 71GHz, so extend the range check till 20GHz (45-71GHZ), else some channels will be marked as disabled. Signed-off-by: Chaitanya Tata <Chaitanya.Tata@bluwireless.co.uk> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2019-01-25cfg80211: reg: remove warn_on for a normal caseChaitanya Tata1-2/+7
If there are simulatenous queries of regdb, then there might be a case where multiple queries can trigger request_firmware_no_wait and can have parallel callbacks being executed asynchronously. In this scenario we might hit the WARN_ON. So remove the warn_on, as the code already handles multiple callbacks gracefully. Signed-off-by: Chaitanya Tata <chaitanya.tata@bluwireless.co.uk> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2019-01-25mac80211: Add attribute aligned(2) to struct 'action'Mathieu Malaterre1-1/+1
During refactor in commit 9e478066eae4 ("mac80211: fix MU-MIMO follow-MAC mode") a new struct 'action' was declared with packed attribute as: struct { struct ieee80211_hdr_3addr hdr; u8 category; u8 action_code; } __packed action; But since struct 'ieee80211_hdr_3addr' is declared with an aligned keyword as: struct ieee80211_hdr { __le16 frame_control; __le16 duration_id; u8 addr1[ETH_ALEN]; u8 addr2[ETH_ALEN]; u8 addr3[ETH_ALEN]; __le16 seq_ctrl; u8 addr4[ETH_ALEN]; } __packed __aligned(2); Solve the ambiguity of placing aligned structure in a packed one by adding the aligned(2) attribute to struct 'action'. This removes the following warning (W=1): net/mac80211/rx.c:234:2: warning: alignment 1 of 'struct <anonymous>' is less than 2 [-Wpacked-not-aligned] Cc: Johannes Berg <johannes.berg@intel.com> Suggested-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Mathieu Malaterre <malat@debian.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2019-01-25mac80211: don't initiate TDLS connection if station is not associated to APBalaji Pothunoori1-0/+4
Following call trace is observed while adding TDLS peer entry in driver during TDLS setup. Call Trace: [<c1301476>] dump_stack+0x47/0x61 [<c10537d2>] __warn+0xe2/0x100 [<fa22415f>] ? sta_apply_parameters+0x49f/0x550 [mac80211] [<c1053895>] warn_slowpath_null+0x25/0x30 [<fa22415f>] sta_apply_parameters+0x49f/0x550 [mac80211] [<fa20ad42>] ? sta_info_alloc+0x1c2/0x450 [mac80211] [<fa224623>] ieee80211_add_station+0xe3/0x160 [mac80211] [<c1876fe3>] nl80211_new_station+0x273/0x420 [<c170f6d9>] genl_rcv_msg+0x219/0x3c0 [<c170f4c0>] ? genl_rcv+0x30/0x30 [<c170ee7e>] netlink_rcv_skb+0x8e/0xb0 [<c170f4ac>] genl_rcv+0x1c/0x30 [<c170e8aa>] netlink_unicast+0x13a/0x1d0 [<c170ec18>] netlink_sendmsg+0x2d8/0x390 [<c16c5acd>] sock_sendmsg+0x2d/0x40 [<c16c6369>] ___sys_sendmsg+0x1d9/0x1e0 Fixing this by allowing TDLS setup request only when we have completed association. Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2019-01-25nl80211: fix NLA_POLICY_NESTED() argumentsJohannes Berg1-1/+1
syzbot reported an out-of-bounds read when passing certain malformed messages into nl80211. The specific place where this happened isn't interesting, the problem is that nested policy parsing was referring to the wrong maximum attribute and thus the policy wasn't long enough. Fix this by referring to the correct attribute. Since this is really not necessary, I'll come up with a separate patch to just pass the policy instead of both, in the common case we can infer the maxattr from the size of the policy array. Reported-by: syzbot+4157b036c5f4713b1f2f@syzkaller.appspotmail.com Cc: stable@vger.kernel.org Fixes: 9bb7e0f24e7e ("cfg80211: add peer measurement with FTM initiator API") Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2019-01-24Merge tag 'linux-can-fixes-for-5.0-20190122' of ↵David S. Miller1-0/+27
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can Marc Kleine-Budde says: ==================== pull-request: can 2019-01-22 this is a pull request of 4 patches for net/master. The first patch by is by Manfred Schlaegl and reverts a patch that caused wrong warning messages in certain use cases. The next patch is by Oliver Hartkopp for the bcm that adds sanity checks for the timer value before using it to detect potential interger overflows. The last two patches are for the flexcan driver, YueHaibing's patch fixes the the return value in the error path of the flexcan_setup_stop_mode() function. The second patch is by Uwe Kleine-König and fixes a NULL pointer deref on older flexcan cores in flexcan_chip_start(). ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-24sctp: set flow sport from saddr only when it's 0Xin Long2-2/+4
Now sctp_transport_pmtu() passes transport->saddr into .get_dst() to set flow sport from 'saddr'. However, transport->saddr is set only when transport->dst exists in sctp_transport_route(). If sctp_transport_pmtu() is called without transport->saddr set, like when transport->dst doesn't exists, the flow sport will be set to 0 from transport->saddr, which will cause a wrong route to be got. Commit 6e91b578bf3f ("sctp: re-use sctp_transport_pmtu in sctp_transport_route") made the issue be triggered more easily since sctp_transport_pmtu() would be called in sctp_transport_route() after that. In gerneral, fl4->fl4_sport should always be set to htons(asoc->base.bind_addr.port), unless transport->asoc doesn't exist in sctp_v4/6_get_dst(), which is the case: sctp_ootb_pkt_new() -> sctp_transport_route() For that, we can simply handle it by setting flow sport from saddr only when it's 0 in sctp_v4/6_get_dst(). Fixes: 6e91b578bf3f ("sctp: re-use sctp_transport_pmtu in sctp_transport_route") Reported-by: Ying Xu <yinxu@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-24sctp: set chunk transport correctly when it's a new asocXin Long1-3/+8
In the paths: sctp_sf_do_unexpected_init() -> sctp_make_init_ack() sctp_sf_do_dupcook_a/b()() -> sctp_sf_do_5_1D_ce() The new chunk 'retval' transport is set from the incoming chunk 'chunk' transport. However, 'retval' transport belong to the new asoc, which is a different one from 'chunk' transport's asoc. It will cause that the 'retval' chunk gets set with a wrong transport. Later when sending it and because of Commit b9fd683982c9 ("sctp: add sctp_packet_singleton"), sctp_packet_singleton() will set some fields, like vtag to 'retval' chunk from that wrong transport's asoc. This patch is to fix it by setting 'retval' transport correctly which belongs to the right asoc in sctp_make_init_ack() and sctp_sf_do_5_1D_ce(). Fixes: b9fd683982c9 ("sctp: add sctp_packet_singleton") Reported-by: Ying Xu <yinxu@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-24sctp: improve the events for sctp stream addingXin Long1-11/+8
This patch is to improve sctp stream adding events in 2 places: 1. In sctp_process_strreset_addstrm_out(), move up SCTP_MAX_STREAM and in stream allocation failure checks, as the adding has to succeed after reconf_timer stops for the in stream adding request retransmission. 3. In sctp_process_strreset_addstrm_in(), no event should be sent, as no in or out stream is added here. Fixes: 50a41591f110 ("sctp: implement receiver-side procedures for the Add Outgoing Streams Request Parameter") Fixes: c5c4ebb3ab87 ("sctp: implement receiver-side procedures for the Add Incoming Streams Request Parameter") Reported-by: Ying Xu <yinxu@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-24sctp: improve the events for sctp stream resetXin Long1-22/+17
This patch is to improve sctp stream reset events in 4 places: 1. In sctp_process_strreset_outreq(), the flag should always be set with SCTP_STREAM_RESET_INCOMING_SSN instead of OUTGOING, as receiver's in stream is reset here. 2. In sctp_process_strreset_outreq(), move up SCTP_STRRESET_ERR_WRONG_SSN check, as the reset has to succeed after reconf_timer stops for the in stream reset request retransmission. 3. In sctp_process_strreset_inreq(), no event should be sent, as no in or out stream is reset here. 4. In sctp_process_strreset_resp(), SCTP_STREAM_RESET_INCOMING_SSN or OUTGOING event should always be sent for stream reset requests, no matter it fails or succeeds to process the request. Fixes: 810544764536 ("sctp: implement receiver-side procedures for the Outgoing SSN Reset Request Parameter") Fixes: 16e1a91965b0 ("sctp: implement receiver-side procedures for the Incoming SSN Reset Request Parameter") Fixes: 11ae76e67a17 ("sctp: implement receiver-side procedures for the Reconf Response Parameter") Reported-by: Ying Xu <yinxu@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-24ip_tunnel: Make none-tunnel-dst tunnel port work with lwtunnelwenxu1-1/+7
ip l add dev tun type gretap key 1000 ip a a dev tun 10.0.0.1/24 Packets with tun-id 1000 can be recived by tun dev. But packet can't be sent through dev tun for non-tunnel-dst With this patch: tunnel-dst can be get through lwtunnel like beflow: ip r a 10.0.0.7 encap ip dst 172.168.0.11 dev tun Signed-off-by: wenxu <wenxu@ucloud.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-23ax25: fix possible use-after-freeEric Dumazet2-13/+10
syzbot found that ax25 routes where not properly protected against concurrent use [1]. In this particular report the bug happened while copying ax25->digipeat. Fix this problem by making sure we call ax25_get_route() while ax25_route_lock is held, so that no modification could happen while using the route. The current two ax25_get_route() callers do not sleep, so this change should be fine. Once we do that, ax25_get_route() no longer needs to grab a reference on the found route. [1] ax25_connect(): syz-executor0 uses autobind, please contact jreuter@yaina.de BUG: KASAN: use-after-free in memcpy include/linux/string.h:352 [inline] BUG: KASAN: use-after-free in kmemdup+0x42/0x60 mm/util.c:113 Read of size 66 at addr ffff888066641a80 by task syz-executor2/531 ax25_connect(): syz-executor0 uses autobind, please contact jreuter@yaina.de CPU: 1 PID: 531 Comm: syz-executor2 Not tainted 5.0.0-rc2+ #10 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x1db/0x2d0 lib/dump_stack.c:113 print_address_description.cold+0x7c/0x20d mm/kasan/report.c:187 kasan_report.cold+0x1b/0x40 mm/kasan/report.c:317 check_memory_region_inline mm/kasan/generic.c:185 [inline] check_memory_region+0x123/0x190 mm/kasan/generic.c:191 memcpy+0x24/0x50 mm/kasan/common.c:130 memcpy include/linux/string.h:352 [inline] kmemdup+0x42/0x60 mm/util.c:113 kmemdup include/linux/string.h:425 [inline] ax25_rt_autobind+0x25d/0x750 net/ax25/ax25_route.c:424 ax25_connect.cold+0x30/0xa4 net/ax25/af_ax25.c:1224 __sys_connect+0x357/0x490 net/socket.c:1664 __do_sys_connect net/socket.c:1675 [inline] __se_sys_connect net/socket.c:1672 [inline] __x64_sys_connect+0x73/0xb0 net/socket.c:1672 do_syscall_64+0x1a3/0x800 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x458099 Code: 6d b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 3b b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007f870ee22c78 EFLAGS: 00000246 ORIG_RAX: 000000000000002a RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 0000000000458099 RDX: 0000000000000048 RSI: 0000000020000080 RDI: 0000000000000005 RBP: 000000000073bf00 R08: 0000000000000000 R09: 0000000000000000 ax25_connect(): syz-executor4 uses autobind, please contact jreuter@yaina.de R10: 0000000000000000 R11: 0000000000000246 R12: 00007f870ee236d4 R13: 00000000004be48e R14: 00000000004ce9a8 R15: 00000000ffffffff Allocated by task 526: save_stack+0x45/0xd0 mm/kasan/common.c:73 set_track mm/kasan/common.c:85 [inline] __kasan_kmalloc mm/kasan/common.c:496 [inline] __kasan_kmalloc.constprop.0+0xcf/0xe0 mm/kasan/common.c:469 kasan_kmalloc+0x9/0x10 mm/kasan/common.c:504 ax25_connect(): syz-executor5 uses autobind, please contact jreuter@yaina.de kmem_cache_alloc_trace+0x151/0x760 mm/slab.c:3609 kmalloc include/linux/slab.h:545 [inline] ax25_rt_add net/ax25/ax25_route.c:95 [inline] ax25_rt_ioctl+0x3b9/0x1270 net/ax25/ax25_route.c:233 ax25_ioctl+0x322/0x10b0 net/ax25/af_ax25.c:1763 sock_do_ioctl+0xe2/0x400 net/socket.c:950 sock_ioctl+0x32f/0x6c0 net/socket.c:1074 vfs_ioctl fs/ioctl.c:46 [inline] file_ioctl fs/ioctl.c:509 [inline] do_vfs_ioctl+0x107b/0x17d0 fs/ioctl.c:696 ksys_ioctl+0xab/0xd0 fs/ioctl.c:713 __do_sys_ioctl fs/ioctl.c:720 [inline] __se_sys_ioctl fs/ioctl.c:718 [inline] __x64_sys_ioctl+0x73/0xb0 fs/ioctl.c:718 do_syscall_64+0x1a3/0x800 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe ax25_connect(): syz-executor5 uses autobind, please contact jreuter@yaina.de Freed by task 550: save_stack+0x45/0xd0 mm/kasan/common.c:73 set_track mm/kasan/common.c:85 [inline] __kasan_slab_free+0x102/0x150 mm/kasan/common.c:458 kasan_slab_free+0xe/0x10 mm/kasan/common.c:466 __cache_free mm/slab.c:3487 [inline] kfree+0xcf/0x230 mm/slab.c:3806 ax25_rt_add net/ax25/ax25_route.c:92 [inline] ax25_rt_ioctl+0x304/0x1270 net/ax25/ax25_route.c:233 ax25_ioctl+0x322/0x10b0 net/ax25/af_ax25.c:1763 sock_do_ioctl+0xe2/0x400 net/socket.c:950 sock_ioctl+0x32f/0x6c0 net/socket.c:1074 vfs_ioctl fs/ioctl.c:46 [inline] file_ioctl fs/ioctl.c:509 [inline] do_vfs_ioctl+0x107b/0x17d0 fs/ioctl.c:696 ksys_ioctl+0xab/0xd0 fs/ioctl.c:713 __do_sys_ioctl fs/ioctl.c:720 [inline] __se_sys_ioctl fs/ioctl.c:718 [inline] __x64_sys_ioctl+0x73/0xb0 fs/ioctl.c:718 do_syscall_64+0x1a3/0x800 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe The buggy address belongs to the object at ffff888066641a80 which belongs to the cache kmalloc-96 of size 96 The buggy address is located 0 bytes inside of 96-byte region [ffff888066641a80, ffff888066641ae0) The buggy address belongs to the page: page:ffffea0001999040 count:1 mapcount:0 mapping:ffff88812c3f04c0 index:0x0 flags: 0x1fffc0000000200(slab) ax25_connect(): syz-executor4 uses autobind, please contact jreuter@yaina.de raw: 01fffc0000000200 ffffea0001817948 ffffea0002341dc8 ffff88812c3f04c0 raw: 0000000000000000 ffff888066641000 0000000100000020 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff888066641980: fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc ffff888066641a00: 00 00 00 00 00 00 00 00 02 fc fc fc fc fc fc fc >ffff888066641a80: fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc ^ ffff888066641b00: fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc ffff888066641b80: 00 00 00 00 00 00 00 00 00 00 00 00 fc fc fc fc Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Ralf Baechle <ralf@linux-mips.org> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-22net/ipv6: lower the level of "link is not ready" messagesLubomir Rintel1-2/+2
This message gets logged far too often for how interesting is it. Most distributions nowadays configure NetworkManager to use randomly generated MAC addresses for Wi-Fi network scans. The interfaces end up being periodically brought down for the address change. When they're subsequently brought back up, the message is logged, eventually flooding the log. Perhaps the message is not all that helpful: it seems to be more interesting to hear when the addrconf actually start, not when it does not. Let's lower its level. Signed-off-by: Lubomir Rintel <lkundrak@v3.sk> Acked-By: Thomas Haller <thaller@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-22net/ipv6: don't return positive numbers when nothing was dumpedJakub Kicinski1-0/+2
in6_dump_addrs() returns a positive 1 if there was nothing to dump. This return value can not be passed as return from inet6_dump_addr() as is, because it will confuse rtnetlink, resulting in NLMSG_DONE never getting set: $ ip addr list dev lo EOF on netlink Dump terminated v2: flip condition to avoid a new goto (DaveA) Fixes: 7c1e8a3817c5 ("netlink: fixup regression in RTM_GETADDR") Reported-by: Brendan Galloway <brendan.galloway@netronome.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: David Ahern <dsahern@gmail.com> Tested-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-22net: ip_gre: use erspan key field for tunnel lookupLorenzo Bianconi3-13/+17
Use ERSPAN key header field as tunnel key in gre_parse_header routine since ERSPAN protocol sets the key field of the external GRE header to 0 resulting in a tunnel lookup fail in ip6gre_err. In addition remove key field parsing and pskb_may_pull check in erspan_rcv and ip6erspan_rcv Fixes: 5a963eb61b7c ("ip6_gre: Add ERSPAN native tunnel support") Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-22can: bcm: check timer values before ktime conversionOliver Hartkopp1-0/+27
Kyungtae Kim detected a potential integer overflow in bcm_[rx|tx]_setup() when the conversion into ktime multiplies the given value with NSEC_PER_USEC (1000). Reference: https://marc.info/?l=linux-can&m=154732118819828&w=2 Add a check for the given tv_usec, so that the value stays below one second. Additionally limit the tv_sec value to a reasonable value for CAN related use-cases of 400 days and ensure all values to be positive. Reported-by: Kyungtae Kim <kt0755@gmail.com> Tested-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Cc: linux-stable <stable@vger.kernel.org> # >= 2.6.26 Tested-by: Kyungtae Kim <kt0755@gmail.com> Acked-by: Andre Naujoks <nautsch2@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-01-21libceph: avoid KEEPALIVE_PENDING races in ceph_con_keepalive()Ilya Dryomov1-2/+3
con_fault() can transition the connection into STANDBY right after ceph_con_keepalive() clears STANDBY in clear_standby(): libceph user thread ceph-msgr worker ceph_con_keepalive() mutex_lock(&con->mutex) clear_standby(con) mutex_unlock(&con->mutex) mutex_lock(&con->mutex) con_fault() ... if KEEPALIVE_PENDING isn't set set state to STANDBY ... mutex_unlock(&con->mutex) set KEEPALIVE_PENDING set WRITE_PENDING This triggers warnings in clear_standby() when either ceph_con_send() or ceph_con_keepalive() get to clearing STANDBY next time. I don't see a reason to condition queue_con() call on the previous value of KEEPALIVE_PENDING, so move the setting of KEEPALIVE_PENDING into the critical section -- unlike WRITE_PENDING, KEEPALIVE_PENDING could have been a non-atomic flag. Reported-by: syzbot+acdeb633f6211ccdf886@syzkaller.appspotmail.com Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Tested-by: Myungho Jung <mhjungk@gmail.com>
2019-01-21Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds51-322/+296
Pull networking fixes from David Miller: 1) Fix endless loop in nf_tables, from Phil Sutter. 2) Fix cross namespace ip6_gre tunnel hash list corruption, from Olivier Matz. 3) Don't be too strict in phy_start_aneg() otherwise we might not allow restarting auto negotiation. From Heiner Kallweit. 4) Fix various KMSAN uninitialized value cases in tipc, from Ying Xue. 5) Memory leak in act_tunnel_key, from Davide Caratti. 6) Handle chip errata of mv88e6390 PHY, from Andrew Lunn. 7) Remove linear SKB assumption in fou/fou6, from Eric Dumazet. 8) Missing udplite rehash callbacks, from Alexey Kodanev. 9) Log dirty pages properly in vhost, from Jason Wang. 10) Use consume_skb() in neigh_probe() as this is a normal free not a drop, from Yang Wei. Likewise in macvlan_process_broadcast(). 11) Missing device_del() in mdiobus_register() error paths, from Thomas Petazzoni. 12) Fix checksum handling of short packets in mlx5, from Cong Wang. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (96 commits) bpf: in __bpf_redirect_no_mac pull mac only if present virtio_net: bulk free tx skbs net: phy: phy driver features are mandatory isdn: avm: Fix string plus integer warning from Clang net/mlx5e: Fix cb_ident duplicate in indirect block register net/mlx5e: Fix wrong (zero) TX drop counter indication for representor net/mlx5e: Fix wrong error code return on FEC query failure net/mlx5e: Force CHECKSUM_UNNECESSARY for short ethernet frames tools: bpftool: Cleanup license mess bpf: fix inner map masking to prevent oob under speculation bpf: pull in pkt_sched.h header for tooling to fix bpftool build selftests: forwarding: Add a test case for externally learned FDB entries selftests: mlxsw: Test FDB offload indication mlxsw: spectrum_switchdev: Do not treat static FDB entries as sticky net: bridge: Mark FDB entries that were added by user as such mlxsw: spectrum_fid: Update dummy FID index mlxsw: pci: Return error on PCI reset timeout mlxsw: pci: Increase PCI SW reset timeout mlxsw: pci: Ring CQ's doorbell before RDQ's MAINTAINERS: update email addresses of liquidio driver maintainers ...
2019-01-19Merge git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpfDavid S. Miller3-15/+34
Daniel Borkmann says: ==================== pull-request: bpf 2019-01-20 The following pull-request contains BPF updates for your *net* tree. The main changes are: 1) Fix a out-of-bounds access in __bpf_redirect_no_mac, from Willem. 2) Fix bpf_setsockopt to reset sock dst on SO_MARK changes, from Peter. 3) Fix map in map masking to prevent out-of-bounds access under speculative execution, from Daniel. 4) Fix bpf_setsockopt's SO_MAX_PACING_RATE to support TCP internal pacing, from Yuchung. 5) Fix json writer license in bpftool, from Thomas. 6) Fix AF_XDP to check if an actually queue exists during umem setup, from Krzysztof. 7) Several fixes to BPF stackmap's build id handling. Another fix for bpftool build to account for libbfd variations wrt linking requirements, from Stanislav. 8) Fix BPF samples build with clang by working around missing asm goto, from Yonghong. 9) Fix libbpf to retry program load on signal interrupt, from Lorenz. 10) Various minor compile warning fixes in BPF code, from Mathieu. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-20bpf: in __bpf_redirect_no_mac pull mac only if presentWillem de Bruijn2-10/+12
Syzkaller was able to construct a packet of negative length by redirecting from bpf_prog_test_run_skb with BPF_PROG_TYPE_LWT_XMIT: BUG: KASAN: slab-out-of-bounds in memcpy include/linux/string.h:345 [inline] BUG: KASAN: slab-out-of-bounds in skb_copy_from_linear_data include/linux/skbuff.h:3421 [inline] BUG: KASAN: slab-out-of-bounds in __pskb_copy_fclone+0x2dd/0xeb0 net/core/skbuff.c:1395 Read of size 4294967282 at addr ffff8801d798009c by task syz-executor2/12942 kasan_report.cold.9+0x242/0x309 mm/kasan/report.c:412 check_memory_region_inline mm/kasan/kasan.c:260 [inline] check_memory_region+0x13e/0x1b0 mm/kasan/kasan.c:267 memcpy+0x23/0x50 mm/kasan/kasan.c:302 memcpy include/linux/string.h:345 [inline] skb_copy_from_linear_data include/linux/skbuff.h:3421 [inline] __pskb_copy_fclone+0x2dd/0xeb0 net/core/skbuff.c:1395 __pskb_copy include/linux/skbuff.h:1053 [inline] pskb_copy include/linux/skbuff.h:2904 [inline] skb_realloc_headroom+0xe7/0x120 net/core/skbuff.c:1539 ipip6_tunnel_xmit net/ipv6/sit.c:965 [inline] sit_tunnel_xmit+0xe1b/0x30d0 net/ipv6/sit.c:1029 __netdev_start_xmit include/linux/netdevice.h:4325 [inline] netdev_start_xmit include/linux/netdevice.h:4334 [inline] xmit_one net/core/dev.c:3219 [inline] dev_hard_start_xmit+0x295/0xc90 net/core/dev.c:3235 __dev_queue_xmit+0x2f0d/0x3950 net/core/dev.c:3805 dev_queue_xmit+0x17/0x20 net/core/dev.c:3838 __bpf_tx_skb net/core/filter.c:2016 [inline] __bpf_redirect_common net/core/filter.c:2054 [inline] __bpf_redirect+0x5cf/0xb20 net/core/filter.c:2061 ____bpf_clone_redirect net/core/filter.c:2094 [inline] bpf_clone_redirect+0x2f6/0x490 net/core/filter.c:2066 bpf_prog_41f2bcae09cd4ac3+0xb25/0x1000 The generated test constructs a packet with mac header, network header, skb->data pointing to network header and skb->len 0. Redirecting to a sit0 through __bpf_redirect_no_mac pulls the mac length, even though skb->data already is at skb->network_header. bpf_prog_test_run_skb has already pulled it as LWT_XMIT !is_l2. Update the offset calculation to pull only if skb->data differs from skb->network_header, which is not true in this case. The test itself can be run only from commit 1cf1cae963c2 ("bpf: introduce BPF_PROG_TEST_RUN command"), but the same type of packets with skb at network header could already be built from lwt xmit hooks, so this fix is more relevant to that commit. Also set the mac header on redirect from LWT_XMIT, as even after this change to __bpf_redirect_no_mac that field is expected to be set, but is not yet in ip_finish_output2. Fixes: 3a0af8fd61f9 ("bpf: BPF for lightweight tunnel infrastructure") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
2019-01-20Merge tag 'nfs-for-5.0-2' of git://git.linux-nfs.org/projects/anna/linux-nfsLinus Torvalds6-18/+52
Pull NFS client fixes from Anna Schumaker: "These are mostly fixes for SUNRPC bugs, with a single v4.2 copy_file_range() fix mixed in. Stable bugfixes: - Fix TCP receive code on archs with flush_dcache_page() Other bugfixes: - Fix error code in rpcrdma_buffer_create() - Fix a double free in rpcrdma_send_ctxs_create() - Fix kernel BUG at kernel/cred.c:825 - Fix unnecessary retry in nfs42_proc_copy_file_range() - Ensure rq_bytes_sent is reset before request transmission - Ensure we respect the RPCSEC_GSS sequence number limit - Address Kerberos performance/behavior regression" * tag 'nfs-for-5.0-2' of git://git.linux-nfs.org/projects/anna/linux-nfs: SUNRPC: Address Kerberos performance/behavior regression SUNRPC: Ensure we respect the RPCSEC_GSS sequence number limit SUNRPC: Ensure rq_bytes_sent is reset before request transmission NFSv4.2 fix unnecessary retry in nfs4_copy_file_range sunrpc: kernel BUG at kernel/cred.c:825! SUNRPC: Fix TCP receive code on archs with flush_dcache_page() xprtrdma: Double free in rpcrdma_sendctxs_create() xprtrdma: Fix error code in rpcrdma_buffer_create()
2019-01-19mac80211: fix miscounting of ttl-dropped framesBob Copeland1-1/+3
In ieee80211_rx_h_mesh_fwding, we increment the 'dropped_frames_ttl' counter when we decrement the ttl to zero. For unicast frames destined for other hosts, we stop processing the frame at that point. For multicast frames, we do not rebroadcast it in this case, but we do pass the frame up the stack to process it on this STA. That doesn't match the usual definition of "dropped," so don't count those as such. With this change, something like `ping6 -i0.2 ff02::1%mesh0` from a peer in a ttl=1 network no longer increments the counter rapidly. Signed-off-by: Bob Copeland <bobcopeland@fb.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2019-01-18net: bridge: Mark FDB entries that were added by user as suchIdo Schimmel1-0/+5
Externally learned entries can be added by a user or by a switch driver that is notifying the bridge driver about entries that were learned in hardware. In the first case, the entries are not marked with the 'added_by_user' flag, which causes switch drivers to ignore them and not offload them. The 'added_by_user' flag can be set on externally learned FDB entries based on the 'swdev_notify' parameter in br_fdb_external_learn_add(), which effectively means if the created / updated FDB entry was added by a user or not. Fixes: 816a3bed9549 ("switchdev: Add fdb.added_by_user to switchdev notifications") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: Alexander Petrovskiy <alexpe@mellanox.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Cc: Roopa Prabhu <roopa@cumulusnetworks.com> Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Cc: bridge@lists.linux-foundation.org Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-18net: Fix usage of pskb_trim_rcsumRoss Lagerwall3-0/+3
In certain cases, pskb_trim_rcsum() may change skb pointers. Reinitialize header pointers afterwards to avoid potential use-after-frees. Add a note in the documentation of pskb_trim_rcsum(). Found by KASAN. Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-17neighbour: Do not perturb drop profiles when neigh_probeYang Wei1-1/+1
Replace the kfree_skb() by consume_skb() to be drop monitor(dropwatch, perf) friendly. Signed-off-by: Yang Wei <yang.wei9@zte.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-17net: bridge: Fix ethernet header pointer before check skb forwardableYunjian Wang1-5/+4
The skb header should be set to ethernet header before using is_skb_forwardable. Because the ethernet header length has been considered in is_skb_forwardable(including dev->hard_header_len length). To reproduce the issue: 1, add 2 ports on linux bridge br using following commands: $ brctl addbr br $ brctl addif br eth0 $ brctl addif br eth1 2, the MTU of eth0 and eth1 is 1500 3, send a packet(Data 1480, UDP 8, IP 20, Ethernet 14, VLAN 4) from eth0 to eth1 So the expect result is packet larger than 1500 cannot pass through eth0 and eth1. But currently, the packet passes through success, it means eth1's MTU limit doesn't take effect. Fixes: f6367b4660dd ("bridge: use is_skb_forwardable in forward path") Cc: bridge@lists.linux-foundation.org Cc: Nkolay Aleksandrov <nikolay@cumulusnetworks.com> Cc: Roopa Prabhu <roopa@cumulusnetworks.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: Yunjian Wang <wangyunjian@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-17af_packet: fix raw sockets over 6in4 tunnelNicolas Dichtel1-1/+2
Since commit cb9f1b783850, scapy (which uses an AF_PACKET socket in SOCK_RAW mode) is unable to send a basic icmp packet over a sit tunnel: Here is a example of the setup: $ ip link set ntfp2 up $ ip addr add 10.125.0.1/24 dev ntfp2 $ ip tunnel add tun1 mode sit ttl 64 local 10.125.0.1 remote 10.125.0.2 dev ntfp2 $ ip addr add fd00:cafe:cafe::1/128 dev tun1 $ ip link set dev tun1 up $ ip route add fd00:200::/64 dev tun1 $ scapy >>> p = [] >>> p += IPv6(src='fd00:100::1', dst='fd00:200::1')/ICMPv6EchoRequest() >>> send(p, count=1, inter=0.1) >>> quit() $ ip -s link ls dev tun1 | grep -A1 "TX.*errors" TX: bytes packets errors dropped carrier collsns 0 0 1 0 0 0 The problem is that the network offset is set to the hard_header_len of the output device (tun1, ie 14 + 20) and in our case, because the packet is small (48 bytes) the pskb_inet_may_pull() fails (it tries to pull 40 bytes (ipv6 header) starting from the network offset). This problem is more generally related to device with variable hard header length. To avoid a too intrusive patch in the current release, a (ugly) workaround is proposed in this patch. It has to be cleaned up in net-next. Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=993675a3100b1 Link: http://patchwork.ozlabs.org/patch/1024489/ Fixes: cb9f1b783850 ("ip: validate header length on virtual device xmit") CC: Willem de Bruijn <willemb@google.com> CC: Maxim Mikityanskiy <maximmi@mellanox.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-18bpf: fix SO_MAX_PACING_RATE to support TCP internal pacingYuchung Cheng1-0/+4
If sch_fq packet scheduler is not used, TCP can fallback to internal pacing, but this requires sk_pacing_status to be properly set. Fixes: 8c4b4c7e9ff0 ("bpf: Add setsockopt helper function to bpf") Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Lawrence Brakmo <brakmo@fb.com> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
2019-01-18bpf: bpf_setsockopt: reset sock dst on SO_MARK changesPeter Oskolkov1-1/+4
In sock_setsockopt() (net/core/sock.h), when SO_MARK option is used to change sk_mark, sk_dst_reset(sk) is called. The same should be done in bpf_setsockopt(). Fixes: 8c4b4c7e9ff0 ("bpf: Add setsockopt helper function to bpf") Reported-by: Maciej Żenczykowski <maze@google.com> Signed-off-by: Peter Oskolkov <posk@google.com> Acked-by: Martin KaFai Lau <kafai@fb.com> Reviewed-by: Maciej Żenczykowski <maze@google.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
2019-01-17udp6: add missing rehash callback to udpliteAlexey Kodanev3-1/+3
After commit 23b0269e58ae ("net: udp6: prefer listeners bound to an address"), UDP-Lite only works when specifying a local address for the sockets. This is related to the problem addressed in the commit 719f835853a9 ("udp: add rehash on connect()"). Moreover, __udp6_lib_lookup() now looks for a socket immediately in the secondary hash table. And this issue was found with LTP/network tests as well. Fixes: 23b0269e58ae ("net: udp6: prefer listeners bound to an address") Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-17udp: add missing rehash callback to udpliteAlexey Kodanev3-1/+3
After commit 4cdeeee9252a ("net: udp: prefer listeners bound to an address"), UDP-Lite only works when specifying a local address for the sockets. This is related to the problem addressed in the commit 719f835853a9 ("udp: add rehash on connect()"). Moreover, __udp4_lib_lookup() now looks for a socket immediately in the secondary hash table. The issue was found with LTP/network tests (UDP-Lite test-cases). Fixes: 4cdeeee9252a ("net: udp: prefer listeners bound to an address") Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-17net/sched: cls_flower: allocate mask dynamically in fl_change()Ivan Vecera1-5/+14
Recent changes (especially 05cd271fd61a ("cls_flower: Support multiple masks per priority")) in the fl_flow_mask structure grow it and its current size e.g. on x86_64 with defconfig is 760 bytes and more than 1024 bytes with some debug options enabled. Prior the mentioned commit its size was 176 bytes (using defconfig on x86_64). With regard to this fact it's reasonable to allocate this structure dynamically in fl_change() to reduce its stack size. v2: - use kzalloc() instead of kcalloc() Fixes: 05cd271fd61a ("cls_flower: Support multiple masks per priority") Cc: Jiri Pirko <jiri@resnulli.us> Cc: Paul Blakey <paulb@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ivan Vecera <ivecera@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-17bpf: Correctly annotate implicit fall through in bpf_base_func_protoMathieu Malaterre1-1/+1
There is a plan to build the kernel with -Wimplicit-fallthrough and this place in the code produced a warnings (W=1). To preserve as much of the existing comment only change a ‘:’ into a ‘,’. This is enough change, to match the regular expression expected by GCC. This commit removes the following warning: net/core/filter.c:5310:6: warning: this statement may fall through [-Wimplicit-fallthrough=] Signed-off-by: Mathieu Malaterre <malat@debian.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
2019-01-16udp: with udp_segment release on error pathWillem de Bruijn2-8/+24
Failure __ip_append_data triggers udp_flush_pending_frames, but these tests happen later. The skb must be freed directly. Fixes: bec1f6f697362 ("udp: generate gso with UDP_SEGMENT") Reported-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-16net: bpfilter: change section name of bpfilter UMH blob.Taehee Yoo1-1/+1
The section of bpfilter UMH blob is the ".bpfilter_umh". but this is not an explicit section. so linking warning occurred at compile time for the powerpc. So, this patch makes use of the ".rodata" instead of the ".bpfilter_umh". Config condition: CONFIG_BPFILTER=y CONFIG_BPFILTER_UMH=y Result: ld: warning: orphan section `.bpfilter_umh' from `net/bpfilter/bpfilter_umh_blob.o' being placed in section `.bpfilter_umh' Fixes: 61fbf5933d42 ("net: bpfilter: restart bpfilter_umh when error occurred") Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-16ipv6: route: place a warning with duplicated string with correct extackJakub Kicinski1-12/+2
"IPv6: " prefix is already added by pr_fmt, no need to include it again in the pr_warn() format. The message predates extack support, we can replace the whole thing with an extack message. Suggested-by: David Ahern <dsahern@gmail.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-16net/core/neighbour: fix kmemleak minimal reference count for hash tablesKonstantin Khlebnikov1-1/+1
This should be 1 for normal allocations, 0 disables leak reporting. Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Reported-by: Cong Wang <xiyou.wangcong@gmail.com> Fixes: 85704cb8dcfd ("net/core/neighbour: tell kmemleak about hash tables") Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-16sctp: allocate sctp_sockaddr_entry with kzallocXin Long2-7/+2
The similar issue as fixed in Commit 4a2eb0c37b47 ("sctp: initialize sin6_flowinfo for ipv6 addrs in sctp_inet6addr_event") also exists in sctp_inetaddr_event, as Alexander noticed. To fix it, allocate sctp_sockaddr_entry with kzalloc for both sctp ipv4 and ipv6 addresses, as does in sctp_v4/6_copy_addrlist(). Reported-by: Alexander Potapenko <glider@google.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Reported-by: syzbot+ae0c70c0c2d40c51bb92@syzkaller.appspotmail.com Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-16erspan: build the header with the right proto according to erspan_verXin Long2-11/+18
As said in draft-foschiano-erspan-03#section4: Different frame variants known as "ERSPAN Types" can be distinguished based on the GRE "Protocol Type" field value: Type I and II's value is 0x88BE while Type III's is 0x22EB [ETYPES]. So set it properly in erspan_xmit() according to erspan_ver. While at it, also remove the unused parameter 'proto' in erspan_fb_xmit(). Fixes: 94d7d8f29287 ("ip6_gre: add erspan v2 support") Reported-by: Jianlin Shi <jishi@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-16openvswitch: Avoid OOB read when parsing flow nlattrsRoss Lagerwall1-1/+1
For nested and variable attributes, the expected length of an attribute is not known and marked by a negative number. This results in an OOB read when the expected length is later used to check if the attribute is all zeros. Fix this by using the actual length of the attribute rather than the expected length. Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com> Acked-by: Pravin B Shelar <pshelar@ovn.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-16net_sched: refetch skb protocol for each filterCong Wang1-2/+1
Martin reported a set of filters don't work after changing from reclassify to continue. Looking into the code, it looks like skb protocol is not always fetched for each iteration of the filters. But, as demonstrated by Martin, TC actions could modify skb->protocol, for example act_vlan, this means we have to refetch skb protocol in each iteration, rather than using the one we fetch in the beginning of the loop. This bug is _not_ introduced by commit 3b3ae880266d ("net: sched: consolidate tc_classify{,_compat}"), technically, if act_vlan is the only action that modifies skb protocol, then it is commit c7e2b9689ef8 ("sched: introduce vlan action") which introduced this bug. Reported-by: Martin Olsson <martin.olsson+netdev@sentorsecurity.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-15fou, fou6: do not assume linear skbsEric Dumazet2-4/+14
Both gue_err() and gue6_err() incorrectly assume linear skbs. Fix them to use pskb_may_pull(). BUG: KMSAN: uninit-value in gue6_err+0x475/0xc40 net/ipv6/fou6.c:101 CPU: 0 PID: 18083 Comm: syz-executor1 Not tainted 5.0.0-rc1+ #7 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: <IRQ> __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x173/0x1d0 lib/dump_stack.c:113 kmsan_report+0x12e/0x2a0 mm/kmsan/kmsan.c:600 __msan_warning+0x82/0xf0 mm/kmsan/kmsan_instr.c:313 gue6_err+0x475/0xc40 net/ipv6/fou6.c:101 __udp6_lib_err_encap_no_sk net/ipv6/udp.c:434 [inline] __udp6_lib_err_encap net/ipv6/udp.c:491 [inline] __udp6_lib_err+0x18d0/0x2590 net/ipv6/udp.c:522 udplitev6_err+0x118/0x130 net/ipv6/udplite.c:27 icmpv6_notify+0x462/0x9f0 net/ipv6/icmp.c:784 icmpv6_rcv+0x18ac/0x3fa0 net/ipv6/icmp.c:872 ip6_protocol_deliver_rcu+0xb5a/0x23a0 net/ipv6/ip6_input.c:394 ip6_input_finish net/ipv6/ip6_input.c:434 [inline] NF_HOOK include/linux/netfilter.h:289 [inline] ip6_input+0x2b6/0x350 net/ipv6/ip6_input.c:443 dst_input include/net/dst.h:450 [inline] ip6_rcv_finish+0x4e7/0x6d0 net/ipv6/ip6_input.c:76 NF_HOOK include/linux/netfilter.h:289 [inline] ipv6_rcv+0x34b/0x3f0 net/ipv6/ip6_input.c:272 __netif_receive_skb_one_core net/core/dev.c:4973 [inline] __netif_receive_skb net/core/dev.c:5083 [inline] process_backlog+0x756/0x10e0 net/core/dev.c:5923 napi_poll net/core/dev.c:6346 [inline] net_rx_action+0x78b/0x1a60 net/core/dev.c:6412 __do_softirq+0x53f/0x93a kernel/softirq.c:293 do_softirq_own_stack+0x49/0x80 arch/x86/entry/entry_64.S:1039 </IRQ> do_softirq kernel/softirq.c:338 [inline] __local_bh_enable_ip+0x16f/0x1a0 kernel/softirq.c:190 local_bh_enable+0x36/0x40 include/linux/bottom_half.h:32 rcu_read_unlock_bh include/linux/rcupdate.h:696 [inline] ip6_finish_output2+0x1d64/0x25f0 net/ipv6/ip6_output.c:121 ip6_finish_output+0xae4/0xbc0 net/ipv6/ip6_output.c:154 NF_HOOK_COND include/linux/netfilter.h:278 [inline] ip6_output+0x5ca/0x710 net/ipv6/ip6_output.c:171 dst_output include/net/dst.h:444 [inline] ip6_local_out+0x164/0x1d0 net/ipv6/output_core.c:176 ip6_send_skb+0xfa/0x390 net/ipv6/ip6_output.c:1727 udp_v6_send_skb+0x1733/0x1d20 net/ipv6/udp.c:1169 udpv6_sendmsg+0x424e/0x45d0 net/ipv6/udp.c:1466 inet_sendmsg+0x54a/0x720 net/ipv4/af_inet.c:798 sock_sendmsg_nosec net/socket.c:621 [inline] sock_sendmsg net/socket.c:631 [inline] ___sys_sendmsg+0xdb9/0x11b0 net/socket.c:2116 __sys_sendmmsg+0x580/0xad0 net/socket.c:2211 __do_sys_sendmmsg net/socket.c:2240 [inline] __se_sys_sendmmsg+0xbd/0xe0 net/socket.c:2237 __x64_sys_sendmmsg+0x56/0x70 net/socket.c:2237 do_syscall_64+0xbc/0xf0 arch/x86/entry/common.c:291 entry_SYSCALL_64_after_hwframe+0x63/0xe7 RIP: 0033:0x457ec9 Code: 6d b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 3b b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007f4a5204fc78 EFLAGS: 00000246 ORIG_RAX: 0000000000000133 RAX: ffffffffffffffda RBX: 0000000000000004 RCX: 0000000000457ec9 RDX: 00000000040001ab RSI: 0000000020000240 RDI: 0000000000000003 RBP: 000000000073bf00 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00007f4a520506d4 R13: 00000000004c4ce5 R14: 00000000004d85d8 R15: 00000000ffffffff Uninit was created at: kmsan_save_stack_with_flags mm/kmsan/kmsan.c:205 [inline] kmsan_internal_poison_shadow+0x92/0x150 mm/kmsan/kmsan.c:159 kmsan_kmalloc+0xa6/0x130 mm/kmsan/kmsan_hooks.c:176 kmsan_slab_alloc+0xe/0x10 mm/kmsan/kmsan_hooks.c:185 slab_post_alloc_hook mm/slab.h:446 [inline] slab_alloc_node mm/slub.c:2754 [inline] __kmalloc_node_track_caller+0xe9e/0xff0 mm/slub.c:4377 __kmalloc_reserve net/core/skbuff.c:140 [inline] __alloc_skb+0x309/0xa20 net/core/skbuff.c:208 alloc_skb include/linux/skbuff.h:1012 [inline] alloc_skb_with_frags+0x1c7/0xac0 net/core/skbuff.c:5288 sock_alloc_send_pskb+0xafd/0x10a0 net/core/sock.c:2091 sock_alloc_send_skb+0xca/0xe0 net/core/sock.c:2108 __ip6_append_data+0x42ed/0x5dc0 net/ipv6/ip6_output.c:1443 ip6_append_data+0x3c2/0x650 net/ipv6/ip6_output.c:1619 icmp6_send+0x2f5c/0x3c40 net/ipv6/icmp.c:574 icmpv6_send+0xe5/0x110 net/ipv6/ip6_icmp.c:43 ip6_link_failure+0x5c/0x2c0 net/ipv6/route.c:2231 dst_link_failure include/net/dst.h:427 [inline] vti_xmit net/ipv4/ip_vti.c:229 [inline] vti_tunnel_xmit+0xf3b/0x1ea0 net/ipv4/ip_vti.c:265 __netdev_start_xmit include/linux/netdevice.h:4382 [inline] netdev_start_xmit include/linux/netdevice.h:4391 [inline] xmit_one net/core/dev.c:3278 [inline] dev_hard_start_xmit+0x604/0xc40 net/core/dev.c:3294 __dev_queue_xmit+0x2e48/0x3b80 net/core/dev.c:3864 dev_queue_xmit+0x4b/0x60 net/core/dev.c:3897 neigh_direct_output+0x42/0x50 net/core/neighbour.c:1511 neigh_output include/net/neighbour.h:508 [inline] ip6_finish_output2+0x1d4e/0x25f0 net/ipv6/ip6_output.c:120 ip6_finish_output+0xae4/0xbc0 net/ipv6/ip6_output.c:154 NF_HOOK_COND include/linux/netfilter.h:278 [inline] ip6_output+0x5ca/0x710 net/ipv6/ip6_output.c:171 dst_output include/net/dst.h:444 [inline] ip6_local_out+0x164/0x1d0 net/ipv6/output_core.c:176 ip6_send_skb+0xfa/0x390 net/ipv6/ip6_output.c:1727 udp_v6_send_skb+0x1733/0x1d20 net/ipv6/udp.c:1169 udpv6_sendmsg+0x424e/0x45d0 net/ipv6/udp.c:1466 inet_sendmsg+0x54a/0x720 net/ipv4/af_inet.c:798 sock_sendmsg_nosec net/socket.c:621 [inline] sock_sendmsg net/socket.c:631 [inline] ___sys_sendmsg+0xdb9/0x11b0 net/socket.c:2116 __sys_sendmmsg+0x580/0xad0 net/socket.c:2211 __do_sys_sendmmsg net/socket.c:2240 [inline] __se_sys_sendmmsg+0xbd/0xe0 net/socket.c:2237 __x64_sys_sendmmsg+0x56/0x70 net/socket.c:2237 do_syscall_64+0xbc/0xf0 arch/x86/entry/common.c:291 entry_SYSCALL_64_after_hwframe+0x63/0xe7 Fixes: b8a51b38e4d4 ("fou, fou6: ICMP error handlers for FoU and GUE") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Cc: Stefano Brivio <sbrivio@redhat.com> Cc: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-15tcp: allow MSG_ZEROCOPY transmission also in CLOSE_WAIT stateWillem de Bruijn1-1/+1
TCP transmission with MSG_ZEROCOPY fails if the peer closes its end of the connection and so transitions this socket to CLOSE_WAIT state. Transmission in close wait state is acceptable. Other similar tests in the stack (e.g., in FastOpen) accept both states. Relax this test, too. Link: https://www.mail-archive.com/netdev@vger.kernel.org/msg276886.html Link: https://www.mail-archive.com/netdev@vger.kernel.org/msg227390.html Fixes: f214f915e7db ("tcp: enable MSG_ZEROCOPY") Reported-by: Marek Majkowski <marek@cloudflare.com> Signed-off-by: Willem de Bruijn <willemb@google.com> CC: Yuchung Cheng <ycheng@google.com> CC: Neal Cardwell <ncardwell@google.com> CC: Soheil Hassas Yeganeh <soheil@google.com> CC: Alexey Kodanev <alexey.kodanev@oracle.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-15net/sched: act_tunnel_key: fix memory leak in case of action replaceDavide Caratti1-8/+11
running the following TDC test cases: 7afc - Replace tunnel_key set action with all parameters 364d - Replace tunnel_key set action with all parameters and cookie it's possible to trigger kmemleak warnings like: unreferenced object 0xffff94797127ab40 (size 192): comm "tc", pid 3248, jiffies 4300565293 (age 1006.862s) hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 c0 93 f9 8a ff ff ff ff ................ 41 84 ee 89 ff ff ff ff 00 00 00 00 00 00 00 00 A............... backtrace: [<000000001e85b61c>] tunnel_key_init+0x31d/0x820 [act_tunnel_key] [<000000007f3f6ee7>] tcf_action_init_1+0x384/0x4c0 [<00000000e89e3ded>] tcf_action_init+0x12b/0x1a0 [<00000000c1c8c0f8>] tcf_action_add+0x73/0x170 [<0000000095a9fc28>] tc_ctl_action+0x122/0x160 [<000000004bebeac5>] rtnetlink_rcv_msg+0x263/0x2d0 [<000000009fd862dd>] netlink_rcv_skb+0x4a/0x110 [<00000000b55199e7>] netlink_unicast+0x1a0/0x250 [<000000004996cd21>] netlink_sendmsg+0x2c1/0x3c0 [<000000004d6a94b4>] sock_sendmsg+0x36/0x40 [<000000005d9f0208>] ___sys_sendmsg+0x280/0x2f0 [<00000000dec19023>] __sys_sendmsg+0x5e/0xa0 [<000000004b82ac81>] do_syscall_64+0x5b/0x180 [<00000000a0f1209a>] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [<000000002926b2ab>] 0xffffffffffffffff when the tunnel_key action is replaced, the kernel forgets to release the dst metadata: ensure they are released by tunnel_key_init(), the same way it's done in tunnel_key_release(). Fixes: d0f6dd8a914f4 ("net/sched: Introduce act_tunnel_key") Signed-off-by: Davide Caratti <dcaratti@redhat.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-15Revert "rxrpc: Allow failed client calls to be retried"David Howells5-191/+24
The changes introduced to allow rxrpc calls to be retried creates an issue when it comes to refcounting afs_call structs. The problem is that when rxrpc_send_data() queues the last packet for an asynchronous call, the following sequence can occur: (1) The notify_end_tx callback is invoked which causes the state in the afs_call to be changed from AFS_CALL_CL_REQUESTING or AFS_CALL_SV_REPLYING. (2) afs_deliver_to_call() can then process event notifications from rxrpc on the async_work queue. (3) Delivery of events, such as an abort from the server, can cause the afs_call state to be changed to AFS_CALL_COMPLETE on async_work. (4) For an asynchronous call, afs_process_async_call() notes that the call is complete and tried to clean up all the refs on async_work. (5) rxrpc_send_data() might return the amount of data transferred (success) or an error - which could in turn reflect a local error or a received error. Synchronising the clean up after rxrpc_kernel_send_data() returns an error with the asynchronous cleanup is then tricky to get right. Mostly revert commit c038a58ccfd6704d4d7d60ed3d6a0fca13cf13a4. The two API functions the original commit added aren't currently used. This makes rxrpc_kernel_send_data() always return successfully if it queued the data it was given. Note that this doesn't affect synchronous calls since their Rx notification function merely pokes a wait queue and does not refcounting. The asynchronous call notification function *has* to do refcounting and pass a ref over the work item to avoid the need to sync the workqueue in call cleanup. Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-15tipc: fix uninit-value in tipc_nl_compat_doitYing Xue1-1/+1
BUG: KMSAN: uninit-value in tipc_nl_compat_doit+0x404/0xa10 net/tipc/netlink_compat.c:335 CPU: 0 PID: 4514 Comm: syz-executor485 Not tainted 4.16.0+ #87 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:17 [inline] dump_stack+0x185/0x1d0 lib/dump_stack.c:53 kmsan_report+0x142/0x240 mm/kmsan/kmsan.c:1067 __msan_warning_32+0x6c/0xb0 mm/kmsan/kmsan_instr.c:683 tipc_nl_compat_doit+0x404/0xa10 net/tipc/netlink_compat.c:335 tipc_nl_compat_recv+0x164b/0x2700 net/tipc/netlink_compat.c:1153 genl_family_rcv_msg net/netlink/genetlink.c:599 [inline] genl_rcv_msg+0x1686/0x1810 net/netlink/genetlink.c:624 netlink_rcv_skb+0x378/0x600 net/netlink/af_netlink.c:2447 genl_rcv+0x63/0x80 net/netlink/genetlink.c:635 netlink_unicast_kernel net/netlink/af_netlink.c:1311 [inline] netlink_unicast+0x166b/0x1740 net/netlink/af_netlink.c:1337 netlink_sendmsg+0x1048/0x1310 net/netlink/af_netlink.c:1900 sock_sendmsg_nosec net/socket.c:630 [inline] sock_sendmsg net/socket.c:640 [inline] ___sys_sendmsg+0xec0/0x1310 net/socket.c:2046 __sys_sendmsg net/socket.c:2080 [inline] SYSC_sendmsg+0x2a3/0x3d0 net/socket.c:2091 SyS_sendmsg+0x54/0x80 net/socket.c:2087 do_syscall_64+0x309/0x430 arch/x86/entry/common.c:287 entry_SYSCALL_64_after_hwframe+0x3d/0xa2 RIP: 0033:0x43fda9 RSP: 002b:00007ffd0c184ba8 EFLAGS: 00000213 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 00000000004002c8 RCX: 000000000043fda9 RDX: 0000000000000000 RSI: 0000000020023000 RDI: 0000000000000003 RBP: 00000000006ca018 R08: 00000000004002c8 R09: 00000000004002c8 R10: 00000000004002c8 R11: 0000000000000213 R12: 00000000004016d0 R13: 0000000000401760 R14: 0000000000000000 R15: 0000000000000000 Uninit was created at: kmsan_save_stack_with_flags mm/kmsan/kmsan.c:278 [inline] kmsan_internal_poison_shadow+0xb8/0x1b0 mm/kmsan/kmsan.c:188 kmsan_kmalloc+0x94/0x100 mm/kmsan/kmsan.c:314 kmsan_slab_alloc+0x11/0x20 mm/kmsan/kmsan.c:321 slab_post_alloc_hook mm/slab.h:445 [inline] slab_alloc_node mm/slub.c:2737 [inline] __kmalloc_node_track_caller+0xaed/0x11c0 mm/slub.c:4369 __kmalloc_reserve net/core/skbuff.c:138 [inline] __alloc_skb+0x2cf/0x9f0 net/core/skbuff.c:206 alloc_skb include/linux/skbuff.h:984 [inline] netlink_alloc_large_skb net/netlink/af_netlink.c:1183 [inline] netlink_sendmsg+0x9a6/0x1310 net/netlink/af_netlink.c:1875 sock_sendmsg_nosec net/socket.c:630 [inline] sock_sendmsg net/socket.c:640 [inline] ___sys_sendmsg+0xec0/0x1310 net/socket.c:2046 __sys_sendmsg net/socket.c:2080 [inline] SYSC_sendmsg+0x2a3/0x3d0 net/socket.c:2091 SyS_sendmsg+0x54/0x80 net/socket.c:2087 do_syscall_64+0x309/0x430 arch/x86/entry/common.c:287 entry_SYSCALL_64_after_hwframe+0x3d/0xa2 In tipc_nl_compat_recv(), when the len variable returned by nlmsg_attrlen() is 0, the message is still treated as a valid one, which is obviously unresonable. When len is zero, it means the message not only doesn't contain any valid TLV payload, but also TLV header is not included. Under this stituation, tlv_type field in TLV header is still accessed in tipc_nl_compat_dumpit() or tipc_nl_compat_doit(), but the field space is obviously illegal. Of course, it is not initialized. Reported-by: syzbot+bca0dc46634781f08b38@syzkaller.appspotmail.com Reported-by: syzbot+6bdb590321a7ae40c1a6@syzkaller.appspotmail.com Signed-off-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-15tipc: fix uninit-value in tipc_nl_compat_name_table_dumpYing Xue1-0/+2
syzbot reported: BUG: KMSAN: uninit-value in __arch_swab32 arch/x86/include/uapi/asm/swab.h:10 [inline] BUG: KMSAN: uninit-value in __fswab32 include/uapi/linux/swab.h:59 [inline] BUG: KMSAN: uninit-value in tipc_nl_compat_name_table_dump+0x4a8/0xba0 net/tipc/netlink_compat.c:826 CPU: 0 PID: 6290 Comm: syz-executor848 Not tainted 4.19.0-rc8+ #70 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x306/0x460 lib/dump_stack.c:113 kmsan_report+0x1a2/0x2e0 mm/kmsan/kmsan.c:917 __msan_warning+0x7c/0xe0 mm/kmsan/kmsan_instr.c:500 __arch_swab32 arch/x86/include/uapi/asm/swab.h:10 [inline] __fswab32 include/uapi/linux/swab.h:59 [inline] tipc_nl_compat_name_table_dump+0x4a8/0xba0 net/tipc/netlink_compat.c:826 __tipc_nl_compat_dumpit+0x59e/0xdb0 net/tipc/netlink_compat.c:205 tipc_nl_compat_dumpit+0x63a/0x820 net/tipc/netlink_compat.c:270 tipc_nl_compat_handle net/tipc/netlink_compat.c:1151 [inline] tipc_nl_compat_recv+0x1402/0x2760 net/tipc/netlink_compat.c:1210 genl_family_rcv_msg net/netlink/genetlink.c:601 [inline] genl_rcv_msg+0x185c/0x1a20 net/netlink/genetlink.c:626 netlink_rcv_skb+0x394/0x640 net/netlink/af_netlink.c:2454 genl_rcv+0x63/0x80 net/netlink/genetlink.c:637 netlink_unicast_kernel net/netlink/af_netlink.c:1317 [inline] netlink_unicast+0x166d/0x1720 net/netlink/af_netlink.c:1343 netlink_sendmsg+0x1391/0x1420 net/netlink/af_netlink.c:1908 sock_sendmsg_nosec net/socket.c:621 [inline] sock_sendmsg net/socket.c:631 [inline] ___sys_sendmsg+0xe47/0x1200 net/socket.c:2116 __sys_sendmsg net/socket.c:2154 [inline] __do_sys_sendmsg net/socket.c:2163 [inline] __se_sys_sendmsg+0x307/0x460 net/socket.c:2161 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2161 do_syscall_64+0xbe/0x100 arch/x86/entry/common.c:291 entry_SYSCALL_64_after_hwframe+0x63/0xe7 RIP: 0033:0x440179 Code: 18 89 d0 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 fb 13 fc ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007ffecec49318 EFLAGS: 00000213 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 00000000004002c8 RCX: 0000000000440179 RDX: 0000000000000000 RSI: 0000000020000100 RDI: 0000000000000003 RBP: 00000000006ca018 R08: 0000000000000000 R09: 00000000004002c8 R10: 0000000000000000 R11: 0000000000000213 R12: 0000000000401a00 R13: 0000000000401a90 R14: 0000000000000000 R15: 0000000000000000 Uninit was created at: kmsan_save_stack_with_flags mm/kmsan/kmsan.c:255 [inline] kmsan_internal_poison_shadow+0xc8/0x1d0 mm/kmsan/kmsan.c:180 kmsan_kmalloc+0xa4/0x120 mm/kmsan/kmsan_hooks.c:104 kmsan_slab_alloc+0x10/0x20 mm/kmsan/kmsan_hooks.c:113 slab_post_alloc_hook mm/slab.h:446 [inline] slab_alloc_node mm/slub.c:2727 [inline] __kmalloc_node_track_caller+0xb43/0x1400 mm/slub.c:4360 __kmalloc_reserve net/core/skbuff.c:138 [inline] __alloc_skb+0x422/0xe90 net/core/skbuff.c:206 alloc_skb include/linux/skbuff.h:996 [inline] netlink_alloc_large_skb net/netlink/af_netlink.c:1189 [inline] netlink_sendmsg+0xcaf/0x1420 net/netlink/af_netlink.c:1883 sock_sendmsg_nosec net/socket.c:621 [inline] sock_sendmsg net/socket.c:631 [inline] ___sys_sendmsg+0xe47/0x1200 net/socket.c:2116 __sys_sendmsg net/socket.c:2154 [inline] __do_sys_sendmsg net/socket.c:2163 [inline] __se_sys_sendmsg+0x307/0x460 net/socket.c:2161 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2161 do_syscall_64+0xbe/0x100 arch/x86/entry/common.c:291 entry_SYSCALL_64_after_hwframe+0x63/0xe7 We cannot take for granted the thing that the length of data contained in TLV is longer than the size of struct tipc_name_table_query in tipc_nl_compat_name_table_dump(). Reported-by: syzbot+06e771a754829716a327@syzkaller.appspotmail.com Signed-off-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-15tipc: fix uninit-value in tipc_nl_compat_link_setYing Xue1-0/+5
syzbot reports following splat: BUG: KMSAN: uninit-value in strlen+0x3b/0xa0 lib/string.c:486 CPU: 1 PID: 9306 Comm: syz-executor172 Not tainted 4.20.0-rc7+ #2 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x173/0x1d0 lib/dump_stack.c:113 kmsan_report+0x12e/0x2a0 mm/kmsan/kmsan.c:613 __msan_warning+0x82/0xf0 mm/kmsan/kmsan_instr.c:313 strlen+0x3b/0xa0 lib/string.c:486 nla_put_string include/net/netlink.h:1154 [inline] __tipc_nl_compat_link_set net/tipc/netlink_compat.c:708 [inline] tipc_nl_compat_link_set+0x929/0x1220 net/tipc/netlink_compat.c:744 __tipc_nl_compat_doit net/tipc/netlink_compat.c:311 [inline] tipc_nl_compat_doit+0x3aa/0xaf0 net/tipc/netlink_compat.c:344 tipc_nl_compat_handle net/tipc/netlink_compat.c:1107 [inline] tipc_nl_compat_recv+0x14d7/0x2760 net/tipc/netlink_compat.c:1210 genl_family_rcv_msg net/netlink/genetlink.c:601 [inline] genl_rcv_msg+0x185f/0x1a60 net/netlink/genetlink.c:626 netlink_rcv_skb+0x444/0x640 net/netlink/af_netlink.c:2477 genl_rcv+0x63/0x80 net/netlink/genetlink.c:637 netlink_unicast_kernel net/netlink/af_netlink.c:1310 [inline] netlink_unicast+0xf40/0x1020 net/netlink/af_netlink.c:1336 netlink_sendmsg+0x127f/0x1300 net/netlink/af_netlink.c:1917 sock_sendmsg_nosec net/socket.c:621 [inline] sock_sendmsg net/socket.c:631 [inline] ___sys_sendmsg+0xdb9/0x11b0 net/socket.c:2116 __sys_sendmsg net/socket.c:2154 [inline] __do_sys_sendmsg net/socket.c:2163 [inline] __se_sys_sendmsg+0x305/0x460 net/socket.c:2161 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2161 do_syscall_64+0xbc/0xf0 arch/x86/entry/common.c:291 entry_SYSCALL_64_after_hwframe+0x63/0xe7 The uninitialised access happened in nla_put_string(skb, TIPC_NLA_LINK_NAME, lc->name) This is because lc->name string is not validated before it's used. Reported-by: syzbot+d78b8a29241a195aefb8@syzkaller.appspotmail.com Signed-off-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>