| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
As we invalidate the inetpeer tree along with the routing cache now,
we don't need a genid to reset the redirect handling when the routing
cache is flushed.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We initialize the routing metrics with the values cached on the
inetpeer in rt_init_metrics(). So if we have the metrics cached on the
inetpeer, we ignore the user configured fib_metrics.
To fix this issue, we replace the old tree with a fresh initialized
inet_peer_base. The old tree is removed later with a delayed work queue.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now we have:
eth0: link *down*
br0: port 1(eth0) entered *forwarding* state
br_log_state(p) should be called *after* p->state is set
to BR_STATE_DISABLED.
Reported-by: Zilvinas Valinskas <zilvinas@wilibox.com>
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When br_log_state() is reporting state it should say "entered"
istead of "entering" since state at this point is already
changed.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jesse/openvswitch
|
|
When modifying IP addresses or ports on a UDP packet we don't
correctly follow the rules for unchecksummed packets. This meant
that packets without a checksum can be given a incorrect new checksum
and packets with a checksum can become marked as being unchecksummed.
This fixes it to handle those requirements.
Signed-off-by: Jesse Gross <jesse@nicira.com>
|
|
When OVS_VPORT_ATTR_NAME is specified and dp_ifindex is nonzero, the
logical behavior would be for the vport name lookup scope to be limited
to the specified datapath, but in fact the dp_ifindex value was ignored.
This commit causes the search scope to be honored.
Signed-off-by: Ben Pfaff <blp@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
|
|
When forwarding was set and a new net device is register,
we need add this device to the all-router mcast group.
Signed-off-by: Li Wei <lw@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If reliable event delivery is enabled and ctnetlink fails to deliver
the destroy event in early_drop, the conntrack subsystem cannot
drop any the candidate flow that was planned to be evicted.
Reported-by: Kerin Millar <kerframil@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When net.bridge.bridge-nf-filter-vlan-tagged is 0 (default), vlan packets
arriving should not be sent to ip(6)tables by bridge netfilter.
However, it turns out that we currently always send VLAN packets to
netfilter, if ..
a), CONFIG_VLAN_8021Q is enabled ; or
b), CONFIG_VLAN_8021Q is not set but rx vlan offload is enabled
on the bridge port.
This is because bridge netfilter treats skb with
skb->protocol == ETH_P_IP{V6} as "non-vlan packet".
With rx vlan offload on or CONFIG_VLAN_8021Q=y, the vlan header has
already been removed here, and we cannot rely on skb->protocol alone.
Fix this by only using skb->protocol if the skb has no vlan tag,
or if a vlan tag is present and filter-vlan-tagged bridge netfilter
sysctl is enabled.
We cannot remove the skb->protocol == htons(ETH_P_8021Q) test
because the vlan tag is still around in the CONFIG_VLAN_8021Q=n &&
"ethtool -K $itf rxvlan off" case.
reproducer:
iptables -t raw -I PREROUTING -i br0
iptables -t raw -I PREROUTING -i br0.1
Then send packets to an ip address configured on br0.1 interface.
Even with net.bridge.bridge-nf-filter-vlan-tagged=0, the 1st rule
will match instead of the 2nd one.
With this patch applied, the 2nd rule will match instead.
In the non-local address case, netfilter won't be consulted after
this patch unless the sysctl is switched on.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In adf7ff8, a invalid dereference was added in ebt_make_names.
CC [M] net/bridge/netfilter/ebtables.o
net/bridge/netfilter/ebtables.c: In function `ebt_make_names':
net/bridge/netfilter/ebtables.c:1371:20: warning: `t' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since 7d367e0, ctnetlink_new_conntrack is called without holding
the nf_conntrack_lock spinlock. Thus, ctnetlink_parse_nat_setup
does not require to release that spinlock anymore in the NAT module
autoload case.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
user-space ebtables expects 32 bytes-long names, but xt_match names
use 29 bytes. We have to copy less 29 bytes and then, make sure we
fill the remaining bytes with zeroes.
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit fixes tcp_shift_skb_data() so that it does not shift
SACKed data below snd_una.
This fixes an issue whose symptoms exactly match reports showing
tp->sacked_out going negative since 3.3.0-rc4 (see "WARNING: at
net/ipv4/tcp_input.c:3418" thread on netdev).
Since 2008 (832d11c5cd076abc0aa1eaf7be96c81d1a59ce41)
tcp_shift_skb_data() had been shifting SACKed ranges that were below
snd_una. It checked that the *end* of the skb it was about to shift
from was above snd_una, but did not check that the end of the actual
shifted range was above snd_una; this commit adds that check.
Shifting SACKed ranges below snd_una is problematic because for such
ranges tcp_sacktag_one() short-circuits: it does not declare anything
as SACKed and does not increase sacked_out.
Before the fixes in commits cc9a672ee522d4805495b98680f4a3db5d0a0af9
and daef52bab1fd26e24e8e9578f8fb33ba1d0cb412, shifting SACKed ranges
below snd_una happened to work because tcp_shifted_skb() was always
(incorrectly) passing in to tcp_sacktag_one() an skb whose end_seq
tcp_shift_skb_data() had already guaranteed was beyond snd_una. Hence
tcp_sacktag_one() never short-circuited and always increased
tp->sacked_out in this case.
After those two fixes, my testing has verified that shifting SACKed
ranges below snd_una could cause tp->sacked_out to go negative with
the following sequence of events:
(1) tcp_shift_skb_data() sees an skb whose end_seq is beyond snd_una,
then shifts a prefix of that skb that is below snd_una
(2) tcp_shifted_skb() increments the packet count of the
already-SACKed prev sk_buff
(3) tcp_sacktag_one() sees the end of the new SACKed range is below
snd_una, so it short-circuits and doesn't increase tp->sacked_out
(5) tcp_clean_rtx_queue() sees the SACKed skb has been ACKed,
decrements tp->sacked_out by this "inflated" pcount that was
missing a matching increase in tp->sacked_out, and hence
tp->sacked_out underflows to a u32 like 0xFFFFFFFF, which casted
to s32 is negative.
(6) this leads to the warnings seen in the recent "WARNING: at
net/ipv4/tcp_input.c:3418" thread on the netdev list; e.g.:
tcp_input.c:3418 WARN_ON((int)tp->sacked_out < 0);
More generally, I think this bug can be tickled in some cases where
two or more ACKs from the receiver are lost and then a DSACK arrives
that is immediately above an existing SACKed skb in the write queue.
This fix changes tcp_shift_skb_data() to abort this sequence at step
(1) in the scenario above by noticing that the bytes are below snd_una
and not shifting them.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
otherwise source IPv6 address of ICMPV6_MGM_QUERY packet
might be random junk if IPv6 is disabled on interface or
link-local address is not yet ready (DAD).
Signed-off-by: Ulrich Weber <ulrich.weber@sophos.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
nlmsg_parse() might return an error, so test its return value before
potential random memory accesses.
Errors introduced in commit 115c9b81928 (rtnetlink: Fix problem with
buffer allocation)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit bridge: send proper message_age in config BPDU
added this gem:
bpdu.message_age = (jiffies - root->designated_age)
p->designated_age = jiffies + bpdu->message_age;
Notice how bpdu->message_age is negated when reassigned to
bpdu.message_age. This causes message age to decrease breaking the
STP protocol.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
min age increment needs to round up its min age tick for all
HZ values to guarantee message age is increasing.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In tcp_mark_head_lost() we should not attempt to fragment a SACKed skb
to mark the first portion as lost. This is for two primary reasons:
(1) tcp_shifted_skb() coalesces adjacent regions of SACKed skbs. When
doing this, it preserves the sum of their packet counts in order to
reflect the real-world dynamics on the wire. But given that skbs can
have remainders that do not align to MSS boundaries, this packet count
preservation means that for SACKed skbs there is not necessarily a
direct linear relationship between tcp_skb_pcount(skb) and
skb->len. Thus tcp_mark_head_lost()'s previous attempts to fragment
off and mark as lost a prefix of length (packets - oldcnt)*mss from
SACKed skbs were leading to occasional failures of the WARN_ON(len >
skb->len) in tcp_fragment() (which used to be a BUG_ON(); see the
recent "crash in tcp_fragment" thread on netdev).
(2) there is no real point in fragmenting off part of a SACKed skb and
calling tcp_skb_mark_lost() on it, since tcp_skb_mark_lost() is a NOP
for SACKed skbs.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
When tcp_shifted_skb() shifts bytes from the skb that is currently
pointed to by 'highest_sack' then the increment of
TCP_SKB_CB(skb)->seq implicitly advances tcp_highest_sack_seq(). This
implicit advancement, combined with the recent fix to pass the correct
SACKed range into tcp_sacktag_one(), caused tcp_sacktag_one() to think
that the newly SACKed range was before the tcp_highest_sack_seq(),
leading to a call to tcp_update_reordering() with a degree of
reordering matching the size of the newly SACKed range (typically just
1 packet, which is a NOP, but potentially larger).
This commit fixes this by simply calling tcp_sacktag_one() before the
TCP_SKB_CB(skb)->seq advancement that can advance our notion of the
highest SACKed sequence.
Correspondingly, we can simplify the code a little now that
tcp_shifted_skb() should update the lost_cnt_hint in all cases where
skb == tp->lost_skb_hint.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
1) ICMP sockets leave err uninitialized but we try to return it for the
unsupported MSG_OOB case, reported by Dave Jones.
2) Add new Zaurus device ID entries, from Dave Jones.
3) Pointer calculation in hso driver memset is wrong, from Dan
Carpenter.
4) ks8851_probe() checks unsigned value as negative, fix also from Dan
Carpenter.
5) Fix crashes in atl1c driver due to TX queue handling, from Eric
Dumazet. I anticipate some TX side locking fixes coming in the near
future for this driver as well.
6) The inline directive fix in Bluetooth which was breaking the build
only with very new versions of GCC, from Johan Hedberg.
7) Fix crashes in the ATP CLIP code due to ARP cleanups this merge
window, reported by Meelis Roos and fixed by Eric Dumazet.
8) JME driver doesn't flush RX FIFO correctly, from Guo-Fu Tseng.
9) Some ip6_route_output() callers test the return value for NULL, but
this never happens as the convention is to return a dst entry with
dst->error set. Fixes from RonQing Li.
10) Logitech Harmony 900 should be handled by zaurus driver not
cdc_ether, update white lists and black lists accordingly. From
Scott Talbert.
11) Receiving from certain kinds of devices there won't be a MAC header,
so there is no MAC header to fixup in the IPSEC code, and if we try
to do it we'll crash. Fix from Eric Dumazet.
12) Port type array indexing off-by-one in mlx4 driver, fix from Yevgeny
Petrilin.
13) Fix regression in link-down handling in davinci_emac which causes
all RX descriptors to be freed up and therefore RX to wedge
completely, from Christian Riesch.
14) It took two attempts, but ctnetlink soft lockups seem to be
cured now, from Pablo Neira Ayuso.
15) Endianness bug fix in ENIC driver, from Santosh Nayak.
16) The long ago conversion of the PPP fragmentation code over to
abstracted SKB list handling wasn't perfect, once we get an
out of sequence SKB we don't flush the rest of them like we
should. From Ben McKeegan.
17) Fix regression of ->ip_summed initialization in sfc driver.
From Ben Hutchings.
18) Bluetooth timeout mistakenly using msecs instead of jiffies,
from Andrzej Kaczmarek.
19) Using _sync variant of work cancellation results in deadlocks,
use the non _sync variants instead. From Andre Guedes.
20) Bluetooth rfcomm code had reference counting problems leading
to crashes, fix from Octavian Purdila.
21) The conversion of netem over to classful qdisc handling added
two bugs to netem_dequeue(), fixes from Eric Dumazet.
22) Missing pci_iounmap() in ATM Solos driver. Fix from Julia Lawall.
23) b44_pci_exit() should not have __exit tag since it's invoked from
non-__exit code. From Nikola Pajkovsky.
24) The conversion of the neighbour hash tables over to RCU added a
race, fixed here by adding the necessary reread of tbl->nht, fix
from Michel Machado.
25) When we added VF (virtual function) attributes for network device
dumps, this potentially bloats up the size of the dump of one
network device such that the dump size is too large for the buffer
allocated by properly written netlink applications.
In particular, if you add 255 VFs to a network device, parts of
GLIBC stop working.
To fix this, we add an attribute that is used to turn on these
extended portions of the network device dump. Sophisticaed
applications like 'ip' that want to see this stuff will be changed
to set the attribute, whereas things like GLIBC that don't care
about VFs simply will not, and therefore won't be busted by the
mere presence of VFs on a network device.
Thanks to the tireless work of Greg Rose on this fix.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (53 commits)
sfc: Fix assignment of ip_summed for pre-allocated skbs
ppp: fix 'ppp_mp_reconstruct bad seq' errors
enic: Fix endianness bug.
gre: fix spelling in comments
netfilter: ctnetlink: fix soft lockup when netlink adds new entries (v2)
Revert "netfilter: ctnetlink: fix soft lockup when netlink adds new entries"
davinci_emac: Do not free all rx dma descriptors during init
mlx4_core: Fixing array indexes when setting port types
phy: IC+101G and PHY_HAS_INTERRUPT flag
netdev/phy/icplus: Correct broken phy_init code
ipsec: be careful of non existing mac headers
Move Logitech Harmony 900 from cdc_ether to zaurus
hso: memsetting wrong data in hso_get_count()
netfilter: ip6_route_output() never returns NULL.
ethernet/broadcom: ip6_route_output() never returns NULL.
ipv6: ip6_route_output() never returns NULL.
jme: Fix FIFO flush issue
atm: clip: remove clip_tbl
ipv4: ping: Fix recvmsg MSG_OOB error handling.
rtnetlink: Fix problem with buffer allocation
...
|
|
We expected 0 if module doesn't exist, which is no longer the case
(42046e2e45c109ba703993c510401a11f716c8df,
netfilter: x_tables: return -ENOENT for non-existant matches/targets).
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
|
|
The original spelling and bad word choice makes these comments hard to read.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marcell Zambo and Janos Farago noticed and reported that when
new conntrack entries are added via netlink and the conntrack table
gets full, soft lockup happens. This is because the nf_conntrack_lock
is held while nf_conntrack_alloc is called, which is in turn wants
to lock nf_conntrack_lock while evicting entries from the full table.
The patch fixes the soft lockup with limiting the holding of the
nf_conntrack_lock to the minimum, where it's absolutely required.
It required to extend (and thus change) nf_conntrack_hash_insert
so that it makes sure conntrack and ctnetlink do not add the same entry
twice to the conntrack table.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This reverts commit af14cca162ddcdea017b648c21b9b091e4bf1fa4.
This patch contains a race condition between packets and ctnetlink
in the conntrack addition. A new patch to fix this issue follows up.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Niccolo Belli reported ipsec crashes in case we handle a frame without
mac header (atm in his case)
Before copying mac header, better make sure it is present.
Bugzilla reference: https://bugzilla.kernel.org/show_bug.cgi?id=42809
Reported-by: Niccolò Belli <darkbasic@linuxsystems.it>
Tested-by: Niccolò Belli <darkbasic@linuxsystems.it>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
ip6_route_output() never returns NULL, so it is wrong to
check if the return value is NULL.
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ip6_route_output() never returns NULL, so it is wrong to
check if the return value is NULL.
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 32092ecf0644 (atm: clip: Use device neigh support on top of
"arp_tbl".) introduced a bug since clip_tbl is zeroed : Crash occurs in
__neigh_for_each_release()
idle_timer_check() must use instead arp_tbl and neigh_check_cb() should
ignore non clip neighbours.
Idea from David Miller.
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't return an uninitialized variable as the error, return
-EOPNOTSUPP instead.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement a new netlink attribute type IFLA_EXT_MASK. The mask
is a 32 bit value that can be used to indicate to the kernel that
certain extended ifinfo values are requested by the user application.
At this time the only mask value defined is RTEXT_FILTER_VF to
indicate that the user wants the ifinfo dump to send information
about the VFs belonging to the interface.
This patch fixes a bug in which certain applications do not have
large enough buffers to accommodate the extra information returned
by the kernel with large numbers of SR-IOV virtual functions.
Those applications will not send the new netlink attribute with
the interface info dump request netlink messages so they will
not get unexpectedly large request buffers returned by the kernel.
Modifies the rtnl_calcit function to traverse the list of net
devices and compute the minimum buffer size that can hold the
info dumps of all matching devices based upon the filter passed
in via the new netlink attribute filter mask. If no filter
mask is sent then the buffer allocation defaults to NLMSG_GOODSIZE.
With this change it is possible to add yet to be defined netlink
attributes to the dump request which should make it fairly extensible
in the future.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the fixed race condition happens:
1. While function neigh_periodic_work scans the neighbor hash table
pointed by field tbl->nht, it unlocks and locks tbl->lock between
buckets in order to call cond_resched.
2. Assume that function neigh_periodic_work calls cond_resched, that is,
the lock tbl->lock is available, and function neigh_hash_grow runs.
3. Once function neigh_hash_grow finishes, and RCU calls
neigh_hash_free_rcu, the original struct neigh_hash_table that function
neigh_periodic_work was using doesn't exist anymore.
4. Once back at neigh_periodic_work, whenever the old struct
neigh_hash_table is accessed, things can go badly.
Signed-off-by: Michel Machado <michel@digirati.com.br>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
nothing needs to be done for monitor/AP_VLAN mode on calling
ieee80211_bss_info_change_notify -> drv_bss_info_changed with the change
flag 'BSS_CHANGED_IDLE'. 'wl1271' seems to use BSS_CHANGED_IDLE only for
STA and IBSS mode. further the non-idle state of the monitor mode is
taken care by the 'count' variable which counts non-idle interfaces.
ieee80211_idle_off(local, "in use") will be called.
this fixes the following WARNING when we have initially STA mode
(network manager running) and not associated, and change it to monitor
mode with network manager disabled and bringing up the monitor mode.
this changes the idle state from 'true' (STA unassociated) to 'false'
(MONITOR mode)
exposed by the commit 405385f8ce7a2ed8f82e216d88b5282142e1288b
"mac80211: set bss_conf.idle when vif is connected"
WARNING: net/mac80211/main.c:212
ieee80211_bss_info_change_notify+0x1cf/0x330 [mac80211]()
Hardware name: 64756D6
Pid: 3835, comm: ifconfig Tainted: G O
3.3.0-rc3-wl #9
Call Trace:
[<c0133b02>] warn_slowpath_common+0x72/0xa0
[<fc8e8c3f>] ?
ieee80211_bss_info_change_notify+0x1cf/0x330 [mac80211]
[<fc8e8c3f>] ?
ieee80211_bss_info_change_notify+0x1cf/0x330 [mac80211]
[<c0133b52>] warn_slowpath_null+0x22/0x30
[<fc8e8c3f>]
ieee80211_bss_info_change_notify+0x1cf/0x330 [mac80211]
[<fc8f9de3>] __ieee80211_recalc_idle+0x113/0x430
[mac80211]
[<fc8fabc6>] ieee80211_do_open+0x156/0x7e0 [mac80211]
[<fc8f8a25>] ?
ieee80211_check_concurrent_iface+0x25/0x180 [mac80211]
[<c015dd9f>] ? raw_notifier_call_chain+0x1f/0x30
[<fc8fb290>] ieee80211_open+0x40/0x80 [mac80211]
[<c05894f6>] __dev_open+0x96/0xe0
[<c068fba5>] ? _raw_spin_unlock_bh+0x35/0x40
[<c05881d9>] __dev_change_flags+0x109/0x170
[<c0589423>] dev_change_flags+0x23/0x60
[<c05f3770>] devinet_ioctl+0x6a0/0x770
ieee80211 phy0: device no longer idle - in use
Cc: Eliad Peller <eliad@wizery.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
rate control algorithms concludes the rate as invalid
with rate[i].idx < -1 , while they do also check for rate[i].count is
non-zero. it would be safer to zero initialize the 'count' field.
recently we had a ath9k rate control crash where the ath9k rate control
in ath_tx_status assumed to check only for rate[i].count being non-zero
in one instance and ended up in using invalid rate index for
'connection monitoring NULL func frames' which eventually lead to the crash.
thanks to Pavel Roskin for fixing it and finding the root cause.
https://bugzilla.redhat.com/show_bug.cgi?id=768639
Cc: stable@vger.kernel.org
Cc: Pavel Roskin <proski@gnu.org>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Marcell Zambo and Janos Farago noticed and reported that when
new conntrack entries are added via netlink and the conntrack table
gets full, soft lockup happens. This is because the nf_conntrack_lock
is held while nf_conntrack_alloc is called, which is in turn wants
to lock nf_conntrack_lock while evicting entries from the full table.
The patch fixes the soft lockup with limiting the holding of the
nf_conntrack_lock to the minimum, where it's absolutely required.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Assorted fixes, sat in -next for a week or so...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ocfs2: deal with wraparounds of i_nlink in ocfs2_rename()
vfs: fix compat_sys_stat() handling of overflows in st_nlink
quota: Fix deadlock with suspend and quotas
vfs: Provide function to get superblock and wait for it to thaw
vfs: fix panic in __d_lookup() with high dentry hashtable counts
autofs4 - fix lockdep splat in autofs
vfs: fix d_inode_lookup() dentry ref leak
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
commit 50612537e9 (netem: fix classful handling) added two errors in
netem_dequeue()
1) After checking skb at the head of tfifo queue for time constraints,
it dequeues tail skb, thus adding unwanted reordering.
2) qdisc stats are updated twice per packet
(one when packet dequeued from tfifo, once when delivered)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most rate control implementations assume .get_rate and .tx_status are only
called once the per-station data has been fully initialized.
minstrel_ht crashes if this assumption is violated.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
There are situations where we don't have the
necessary rate control information yet for
station entries, e.g. when associating. This
currently doesn't really happen due to the
dummy station handling; explicitly disabling
rate control when it's not initialised will
allow us to remove dummy stations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
We need to use the _sync() version for cancelling the info and security
timer in the L2CAP connection delete path. Otherwise the delayed work
handler might run after the connection object is freed.
Signed-off-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
__cancel_delayed_work() is being used in some paths where we cannot
sleep waiting for the delayed work to finish. However, that function
might return while the timer is running and the work will be queued
again. Replace the calls with safer cancel_delayed_work() version
which spins until the timer handler finishes on other CPUs and
cancels the delayed work.
Signed-off-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
We should only perform a reset in hci_dev_do_close if the
HCI_QUIRK_NO_RESET flag is set (since in such a case a reset will not be
performed when initializing the device).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
|
|
There is an imbalance in the rfcomm_session_hold / rfcomm_session_put
operations which causes the following crash:
[ 685.010159] BUG: unable to handle kernel paging request at 6b6b6b6b
[ 685.010169] IP: [<c149d76d>] rfcomm_process_dlcs+0x1b/0x15e
[ 685.010181] *pdpt = 000000002d665001 *pde = 0000000000000000
[ 685.010191] Oops: 0000 [#1] PREEMPT SMP
[ 685.010247]
[ 685.010255] Pid: 947, comm: krfcommd Tainted: G C 3.0.16-mid8-dirty #44
[ 685.010266] EIP: 0060:[<c149d76d>] EFLAGS: 00010246 CPU: 1
[ 685.010274] EIP is at rfcomm_process_dlcs+0x1b/0x15e
[ 685.010281] EAX: e79f551c EBX: 6b6b6b6b ECX: 00000007 EDX: e79f40b4
[ 685.010288] ESI: e79f4060 EDI: ed4e1f70 EBP: ed4e1f68 ESP: ed4e1f50
[ 685.010295] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
[ 685.010303] Process krfcommd (pid: 947, ti=ed4e0000 task=ed43e5e0 task.ti=ed4e0000)
[ 685.010308] Stack:
[ 685.010312] ed4e1f68 c149eb53 e5925150 e79f4060 ed500000 ed4e1f70 ed4e1f80 c149ec10
[ 685.010331] 00000000 ed43e5e0 00000000 ed4e1f90 ed4e1f9c c149ec87 0000bf54 00000000
[ 685.010348] 00000000 ee03bf54 c149ec37 ed4e1fe4 c104fe01 00000000 00000000 00000000
[ 685.010367] Call Trace:
[ 685.010376] [<c149eb53>] ? rfcomm_process_rx+0x6e/0x74
[ 685.010387] [<c149ec10>] rfcomm_process_sessions+0xb7/0xde
[ 685.010398] [<c149ec87>] rfcomm_run+0x50/0x6d
[ 685.010409] [<c149ec37>] ? rfcomm_process_sessions+0xde/0xde
[ 685.010419] [<c104fe01>] kthread+0x63/0x68
[ 685.010431] [<c104fd9e>] ? __init_kthread_worker+0x42/0x42
[ 685.010442] [<c14dae82>] kernel_thread_helper+0x6/0xd
This issue has been brought up earlier here:
https://lkml.org/lkml/2011/5/21/127
The issue appears to be the rfcomm_session_put in rfcomm_recv_ua. This
operation doesn't seem be to required as for the non-initiator case we
have the rfcomm_process_rx doing an explicit put and in the initiator
case the last dlc_unlink will drive the reference counter to 0.
There have been several attempts to fix these issue:
6c2718d Bluetooth: Do not call rfcomm_session_put() for RFCOMM UA on closed socket
683d949 Bluetooth: Never deallocate a session when some DLC points to it
but AFAICS they do not fix the issue just make it harder to reproduce.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Gopala Krishna Murala <gopala.krishna.murala@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
Since bluetooth uses multiple protocols types, to avoid lockdep
warnings, we need to use different lockdep classes (one for each
protocol type).
This is already done in bt_sock_create but it misses a couple of cases
when new connections are created. This patch corrects that to fix the
following warning:
<4>[ 1864.732366] =======================================================
<4>[ 1864.733030] [ INFO: possible circular locking dependency detected ]
<4>[ 1864.733544] 3.0.16-mid3-00007-gc9a0f62 #3
<4>[ 1864.733883] -------------------------------------------------------
<4>[ 1864.734408] t.android.btclc/4204 is trying to acquire lock:
<4>[ 1864.734869] (rfcomm_mutex){+.+.+.}, at: [<c14970ea>] rfcomm_dlc_close+0x15/0x30
<4>[ 1864.735541]
<4>[ 1864.735549] but task is already holding lock:
<4>[ 1864.736045] (sk_lock-AF_BLUETOOTH){+.+.+.}, at: [<c1498bf7>] lock_sock+0xa/0xc
<4>[ 1864.736732]
<4>[ 1864.736740] which lock already depends on the new lock.
<4>[ 1864.736750]
<4>[ 1864.737428]
<4>[ 1864.737437] the existing dependency chain (in reverse order) is:
<4>[ 1864.738016]
<4>[ 1864.738023] -> #1 (sk_lock-AF_BLUETOOTH){+.+.+.}:
<4>[ 1864.738549] [<c1062273>] lock_acquire+0x104/0x140
<4>[ 1864.738977] [<c13d35c1>] lock_sock_nested+0x58/0x68
<4>[ 1864.739411] [<c1493c33>] l2cap_sock_sendmsg+0x3e/0x76
<4>[ 1864.739858] [<c13d06c3>] __sock_sendmsg+0x50/0x59
<4>[ 1864.740279] [<c13d0ea2>] sock_sendmsg+0x94/0xa8
<4>[ 1864.740687] [<c13d0ede>] kernel_sendmsg+0x28/0x37
<4>[ 1864.741106] [<c14969ca>] rfcomm_send_frame+0x30/0x38
<4>[ 1864.741542] [<c1496a2a>] rfcomm_send_ua+0x58/0x5a
<4>[ 1864.741959] [<c1498447>] rfcomm_run+0x441/0xb52
<4>[ 1864.742365] [<c104f095>] kthread+0x63/0x68
<4>[ 1864.742742] [<c14d5182>] kernel_thread_helper+0x6/0xd
<4>[ 1864.743187]
<4>[ 1864.743193] -> #0 (rfcomm_mutex){+.+.+.}:
<4>[ 1864.743667] [<c1061ada>] __lock_acquire+0x988/0xc00
<4>[ 1864.744100] [<c1062273>] lock_acquire+0x104/0x140
<4>[ 1864.744519] [<c14d2c70>] __mutex_lock_common+0x3b/0x33f
<4>[ 1864.744975] [<c14d303e>] mutex_lock_nested+0x2d/0x36
<4>[ 1864.745412] [<c14970ea>] rfcomm_dlc_close+0x15/0x30
<4>[ 1864.745842] [<c14990d9>] __rfcomm_sock_close+0x5f/0x6b
<4>[ 1864.746288] [<c1499114>] rfcomm_sock_shutdown+0x2f/0x62
<4>[ 1864.746737] [<c13d275d>] sys_socketcall+0x1db/0x422
<4>[ 1864.747165] [<c14d42f0>] syscall_call+0x7/0xb
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
