| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull networking fixes from David Miller:
"Bug fixes galore, mostly in drivers as is often the case:
1) USB gadget and cdc_eem drivers need adjustments to their frame size
lengths in order to handle VLANs correctly. From Ian Coolidge.
2) TIPC and several network drivers erroneously call tasklet_disable
before tasklet_kill, fix from Xiaotian Feng.
3) r8169 driver needs to apply the WOL suspend quirk to more chipsets,
fix from Cyril Brulebois.
4) Fix multicast filters on RTL_GIGA_MAC_VER_35 r8169 chips, from
Nathan Walp.
5) FDB netlink dumps should use RTM_NEWNEIGH as the message type, not
zero. From John Fastabend.
6) Fix smsc95xx tx checksum offload on big-endian, from Steve
Glendinning.
7) __inet_diag_dump() needs to repsect and report the error value
returned from inet_diag_lock_handler() rather than ignore it.
Otherwise if an inet diag handler is not available for a particular
protocol, we essentially report success instead of giving an error
indication. Fix from Cyrill Gorcunov.
8) When the QFQ packet scheduler sees TSO/GSO packets it does not
handle things properly, and in fact ends up corrupting it's
datastructures as well as mis-schedule packets. Fix from Paolo
Valente.
9) Fix oopser in skb_loop_sk(), from Eric Leblond.
10) CXGB4 passes partially uninitialized datastructures in to FW
commands, fix from Vipul Pandya.
11) When we send unsolicited ipv6 neighbour advertisements, we should
send them to the link-local allnodes multicast address, as per
RFC4861. Fix from Hannes Frederic Sowa.
12) There is some kind of bug in the usbnet's kevent deferral
mechanism, but more immediately when it triggers an uncontrolled
stream of kernel messages spam the log. Rate limit the error log
message triggered when this problem occurs, as sending thousands
of error messages into the kernel log doesn't help matters at all,
and in fact makes further diagnosis more difficult.
From Steve Glendinning.
13) Fix gianfar restore from hibernation, from Wang Dongsheng.
14) The netlink message attribute sizes are wrong in the ipv6 GRE
driver, it was using the size of ipv4 addresses instead of ipv6
ones :-) Fix from Nicolas Dichtel."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
gre6: fix rtnl dump messages
gianfar: ethernet vanishes after restoring from hibernation
usbnet: ratelimit kevent may have been dropped warnings
ipv6: send unsolicited neighbour advertisements to all-nodes
net: usb: cdc_eem: Fix rx skb allocation for 802.1Q VLANs
usb: gadget: g_ether: fix frame size check for 802.1Q
cxgb4: Fix initialization of SGE_CONTROL register
isdn: Make CONFIG_ISDN depend on CONFIG_NETDEVICES
cxgb4: Initialize data structures before using.
af-packet: fix oops when socket is not present
pkt_sched: enable QFQ to support TSO/GSO
net: inet_diag -- Return error code if protocol handler is missed
net: bnx2x: Fix typo in bnx2x driver
smsc95xx: fix tx checksum offload for big endian
rtnetlink: Use nlmsg type RTM_NEWNEIGH from dflt fdb dump
ptp: update adjfreq callback description
r8169: allow multicast packets on sub-8168f chipset.
r8169: Fix WoL on RTL8168d/8111d.
drivers/net: use tasklet_kill in device remove/close process
tipc: do not use tasklet_disable before tasklet_kill
|
|
Spotted after a code review.
Introduced by c12b395a46646bab69089ce7016ac78177f6001f (gre: Support GRE over
IPv6).
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As documented in RFC4861 (Neighbor Discovery for IP version 6) 7.2.6.,
unsolicited neighbour advertisements should be sent to the all-nodes
multicast address.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Due to a NULL dereference, the following patch is causing oops
in normal trafic condition:
commit c0de08d04215031d68fa13af36f347a6cfa252ca
Author: Eric Leblond <eric@regit.org>
Date: Thu Aug 16 22:02:58 2012 +0000
af_packet: don't emit packet on orig fanout group
This buggy patch was a feature fix and has reached most stable
branches.
When skb->sk is NULL and when packet fanout is used, there is a
crash in match_fanout_group where skb->sk is accessed.
This patch fixes the issue by returning false as soon as the
socket is NULL: this correspond to the wanted behavior because
the kernel as to resend the skb to all the listening socket in
this case.
Signed-off-by: Eric Leblond <eric@regit.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the max packet size for some class (configured through tc) is
violated by the actual size of the packets of that class, then QFQ
would not schedule classes correctly, and the data structures
implementing the bucket lists may get corrupted. This problem occurs
with TSO/GSO even if the max packet size is set to the MTU, and is,
e.g., the cause of the failure reported in [1]. Two patches have been
proposed to solve this problem in [2], one of them is a preliminary
version of this patch.
This patch addresses the above issues by: 1) setting QFQ parameters to
proper values for supporting TSO/GSO (in particular, setting the
maximum possible packet size to 64KB), 2) automatically increasing the
max packet size for a class, lmax, when a packet with a larger size
than the current value of lmax arrives.
The drawback of the first point is that the maximum weight for a class
is now limited to 4096, which is equal to 1/16 of the maximum weight
sum.
Finally, this patch also forcibly caps the timestamps of a class if
they are too high to be stored in the bucket list. This capping, taken
from QFQ+ [3], handles the unfrequent case described in the comment to
the function slot_insert.
[1] http://marc.info/?l=linux-netdev&m=134968777902077&w=2
[2] http://marc.info/?l=linux-netdev&m=135096573507936&w=2
[3] http://marc.info/?l=linux-netdev&m=134902691421670&w=2
Signed-off-by: Paolo Valente <paolo.valente@unimore.it>
Tested-by: Cong Wang <amwang@redhat.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We've observed that in case if UDP diag module is not
supported in kernel the netlink returns NLMSG_DONE without
notifying a caller that handler is missed.
This patch makes __inet_diag_dump to return error code instead.
So as example it become possible to detect such situation
and handle it gracefully on userspace level.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
CC: David Miller <davem@davemloft.net>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Pavel Emelyanov <xemul@parallels.com>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull NFS client bugfixes from Trond Myklebust:
- Fix a bunch of deadlock situations:
* State recovery can deadlock if we fail to release sequence ids
before scheduling the recovery thread.
* Calling deactivate_super() from an RPC workqueue thread can
deadlock because of the call to rpc_shutdown_client.
- Display the device name correctly in /proc/*/mounts
- Fix a number of incorrect error return values:
* When NFSv3 mounts fail due to a timeout.
* On NFSv4.1 backchannel setup failure
* On NFSv4 open access checks
- pnfs_find_alloc_layout() must check the layout pointer for NULL
- Fix a regression in the legacy DNS resolved
* tag 'nfs-for-3.7-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS4: nfs4_opendata_access should return errno
NFSv4: Initialise the NFSv4.1 slot table highest_used_slotid correctly
SUNRPC: return proper errno from backchannel_rqst
NFS: add nfs_sb_deactive_async to avoid deadlock
nfs: Show original device name verbatim in /proc/*/mount{s,info}
nfsv3: Make v3 mounts fail with ETIMEDOUTs instead EIO on mountd timeouts
nfs: Check whether a layout pointer is NULL before free it
NFS: fix bug in legacy DNS resolver.
NFSv4: nfs4_locku_done must release the sequence id
NFSv4.1: We must release the sequence id when we fail to get a session slot
NFS: Wait for session recovery to finish before returning
|
|
Change the dflt fdb dump handler to use RTM_NEWNEIGH to
be compatible with bridge dump routines.
The dump reply from the network driver handlers should
match the reply from bridge handler. The fact they were
not in the ixgbe case was effectively a bug. This patch
resolves it.
Applications that were not checking the nlmsg type will
continue to work. And now applications that do check
the type will work as expected.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If tasklet_disable() is called before related tasklet handled,
tasklet_kill will never be finished. tasklet_kill is enough.
Signed-off-by: Xiaotian Feng <dannyfeng@tencent.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Allan Stephens <allan.stephens@windriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: tipc-discussion@lists.sourceforge.net
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
"First post-Sandy pull request"
1) Fix antenna gain handling and initialization of chan->max_reg_power
in wireless, from Felix Fietkau.
2) Fix nexthop handling in H.232 conntrack helper, from Julian
Anastasov.
3) Only process 80211 mesh config header in certain kinds of frames,
from Javier Cardona.
4) 80211 management frame header length needs to be validated, from
Johannes Berg.
5) Don't access free'd SKBs in ath9k driver, from Felix Fietkay.
6) Test for permanent state correctly in VXLAN driver, from Stephen
Hemminger.
7) BNX2X bug fixes from Yaniv Rosner and Dmitry Kravkov.
8) Fix off by one errors in bonding, from Nikolay ALeksandrov.
9) Fix divide by zero in TCP-Illinois congestion control. From Jesper
Dangaard Brouer.
10) TCP metrics code says "Yo dawg, I heard you like sizeof, so I did a
sizeof of a sizeof, so you can size your size" Fix from Julian
Anastasov.
11) Several drivers do mdiobus_free without first doing an
mdiobus_unregister leading to stray pointer references. Fix from
Peter Senna Tschudin.
12) Fix OOPS in l2tp_eth_create() error path, it's another danling
pointer kinda situation. Fix from Tom Parkin.
13) Hardware driven by the vmxnet driver can't handle larger than 16K
fragments, so split them up when necessary. From Eric Dumazet.
14) Handle zero length data length in tcp_send_rcvq() properly. Fix
from Pavel Emelyanov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (38 commits)
tcp-repair: Handle zero-length data put in rcv queue
vmxnet3: must split too big fragments
l2tp: fix oops in l2tp_eth_create() error path
cxgb4: Fix unable to get UP event from the LLD
drivers/net/phy/mdio-bitbang.c: Call mdiobus_unregister before mdiobus_free
drivers/net/ethernet/nxp/lpc_eth.c: Call mdiobus_unregister before mdiobus_free
bnx2x: fix HW initialization using fw 7.8.x
tcp: Fix double sizeof in new tcp_metrics code
net: fix divide by zero in tcp algorithm illinois
net: sctp: Fix typo in net/sctp
bonding: fix second off-by-one error
bonding: fix off-by-one error
bnx2x: Disable FCoE for 57840 since not yet supported by FW
bnx2x: Fix no link on 577xx 10G-baseT
bnx2x: Fix unrecognized SFP+ module after driver is loaded
bnx2x: Fix potential incorrect link speed provision
bnx2x: Restore global registers back to default.
bnx2x: Fix link down in 57712 following LFA
bnx2x: Fix 57810 1G-KR link against certain switches.
ixgbe: PTP get_ts_info missing software support
...
|
|
When sending data into a tcp socket in repair state we should check
for the amount of data being 0 explicitly. Otherwise we'll have an skb
with seq == end_seq in rcv queue, but tcp doesn't expect this to happen
(in particular a warn_on in tcp_recvmsg shoots).
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Reported-by: Giorgos Mavrikas <gmavrikas@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When creating an L2TPv3 Ethernet session, if register_netdev() should fail for
any reason (for example, automatic naming for "l2tpeth%d" interfaces hits the
32k-interface limit), the netdev is freed in the error path. However, the
l2tp_eth_sess structure's dev pointer is left uncleared, and this results in
l2tp_eth_delete() then attempting to unregister the same netdev later in the
session teardown. This results in an oops.
To avoid this, clear the session dev pointer in the error path.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix double sizeof when parsing IPv6 address from
user space because it breaks get/del by specific IPv6 address.
Problem noticed by David Binderman:
https://bugzilla.kernel.org/show_bug.cgi?id=49171
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reading TCP stats when using TCP Illinois congestion control algorithm
can cause a divide by zero kernel oops.
The division by zero occur in tcp_illinois_info() at:
do_div(t, ca->cnt_rtt);
where ca->cnt_rtt can become zero (when rtt_reset is called)
Steps to Reproduce:
1. Register tcp_illinois:
# sysctl -w net.ipv4.tcp_congestion_control=illinois
2. Monitor internal TCP information via command "ss -i"
# watch -d ss -i
3. Establish new TCP conn to machine
Either it fails at the initial conn, or else it needs to wait
for a loss or a reset.
This is only related to reading stats. The function avg_delay() also
performs the same divide, but is guarded with a (ca->cnt_rtt > 0) at its
calling point in update_params(). Thus, simply fix tcp_illinois_info().
Function tcp_illinois_info() / get_info() is called without
socket lock. Thus, eliminate any race condition on ca->cnt_rtt
by using a local stack variable. Simply reuse info.tcpv_rttcnt,
as its already set to ca->cnt_rtt.
Function avg_delay() is not affected by this race condition, as
its called with the socket lock.
Cc: Petr Matousek <pmatouse@redhat.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Correct spelling typo in net/sctp/socket.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The one and only caller (in fs/nfs/nfs4client.c) uses the result
as an errno and would have interpreted an error as EPERM.
Signed-off-by: Weston Andros Adamson <dros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John W. Linville says:
====================
This is a batch of fixes intended for 3.7...
The biggest portion of this is a pull request from Johannes Berg:
"Please pull my mac80211.git tree per below to get a number of fixes. I
have included a patch from Antonio to fix a memcpy overrun, Felix's
patches for the antenna gain/tx power issues, a few mesh-related fixes
from Javier for mac80211 and my own patches to not access data that
might not be present in an skb at all as well as a patch (the duplicate
IE check one) to make mac80211 forward-compatible with potential future
spec extensions that use the same IE multiple times.
It's a bit bigger than I'd like maybe, but I think all of these are
worthwhile fixes at this point."
In addition...
Felix Fietkau fixes an ath9k use-after-free issue.
Stanislaw Gruszka adds a valid value check to rt2800.
Sven Eckelmann adds a check to only check a TID value in a BlockAck, for
frames that could be either a BlockAck or a normal Ack.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
The following patchset contains fixes for your net tree, two of them
are due to relatively recent changes, one has been a longstanding bug,
they are:
* Fix incorrect usage of rt_gateway in the H.323 helper, from
Julian Anastasov.
* Skip re-route in nf_nat code for ICMP traffic. If CONFIG_XFRM is
enabled, we waste cycles to look up for the route again. This problem
seems to be there since really long time. From Ulrich Weber.
* Fix mismatching section in nf_conntrack_reasm, from Hein Tibosch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull Ceph fixes form Sage Weil:
"There are two fixes in the messenger code, one that can trigger a NULL
dereference, and one that error in refcounting (extra put). There is
also a trivial fix that in the fs client code that is triggered by NFS
reexport."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: fix dentry reference leak in encode_fh()
libceph: avoid NULL kref_put when osd reset races with alloc_msg
rbd: reset BACKOFF if unable to re-queue
|
|
WARNING: net/ipv6/netfilter/nf_defrag_ipv6.o(.text+0xe0): Section mismatch in
reference from the function nf_ct_net_init() to the function
.init.text:nf_ct_frag6_sysctl_register()
The function nf_ct_net_init() references the function
__init nf_ct_frag6_sysctl_register().
In case nf_conntrack_ipv6 is compiled as a module, nf_ct_net_init could be
called after the init code and data are unloaded. Therefore remove the
"__net_init" annotation from nf_ct_frag6_sysctl_register().
Signed-off-by: Hein Tibosch <hein_tibosch@yahoo.es>
Acked-by: Cong Wang <amwang@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
ICMP tuples have id in src and type/code in dst.
So comparing src.u.all with dst.u.all will always fail here
and ip_xfrm_me_harder() is called for every ICMP packet,
even if there was no NAT.
Signed-off-by: Ulrich Weber <ulrich.weber@sophos.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Pull networking fixes from David Miller:
"This is what we usually expect at this stage of the game, lots of
little things, mostly in drivers. With the occasional 'oops didn't
mean to do that' kind of regressions in the core code."
1) Uninitialized data in __ip_vs_get_timeouts(), from Arnd Bergmann
2) Reject invalid ACK sequences in Fast Open sockets, from Jerry Chu.
3) Lost error code on return from _rtl_usb_receive(), from Christian
Lamparter.
4) Fix reset resume on USB rt2x00, from Stanislaw Gruszka.
5) Release resources on error in pch_gbe driver, from Veaceslav Falico.
6) Default hop limit not set correctly in ip6_template_metrics[], fix
from Li RongQing.
7) Gianfar PTP code requests wrong kind of resource during probe, fix
from Wei Yang.
8) Fix VHOST net driver on big-endian, from Michael S Tsirkin.
9) Mallenox driver bug fixes from Jack Morgenstein, Or Gerlitz, Moni
Shoua, Dotan Barak, and Uri Habusha.
10) usbnet leaks memory on TX path, fix from Hemant Kumar.
11) Use socket state test, rather than presence of FIN bit packet, to
determine FIONREAD/SIOCINQ value. Fix from Eric Dumazet.
12) Fix cxgb4 build failure, from Vipul Pandya.
13) Provide a SYN_DATA_ACKED state to complement SYN_FASTOPEN in socket
info dumps. From Yuchung Cheng.
14) Fix leak of security path in kfree_skb_partial(). Fix from Eric
Dumazet.
15) Handle RX FIFO overflows more resiliently in pch_gbe driver, from
Veaceslav Falico.
16) Fix MAINTAINERS file pattern for networking drivers, from Jean
Delvare.
17) Add iPhone5 IDs to IPHETH driver, from Jay Purohit.
18) VLAN device type change restriction is too strict, and should not
trigger for the automatically generated vlan0 device. Fix from Jiri
Pirko.
19) Make PMTU/redirect flushing work properly again in ipv4, from
Steffen Klassert.
20) Fix memory corruptions by using kfree_rcu() in netlink_release().
From Eric Dumazet.
21) More qmi_wwan device IDs, from Bjørn Mork.
22) Fix unintentional change of SNAT/DNAT hooks in generic NAT
infrastructure, from Elison Niven.
23) Fix 3.6.x regression in xt_TEE netfilter module, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (57 commits)
tilegx: fix some issues in the SW TSO support
qmi_wwan/cdc_ether: move Novatel 551 and E362 to qmi_wwan
net: usb: Fix memory leak on Tx data path
net/mlx4_core: Unmap UAR also in the case of error flow
net/mlx4_en: Don't use vlan tag value as an indication for vlan presence
net/mlx4_en: Fix double-release-range in tx-rings
bas_gigaset: fix pre_reset handling
vhost: fix mergeable bufs on BE hosts
gianfar_ptp: use iomem, not ioports resource tree in probe
ipv6: Set default hoplimit as zero.
NET_VENDOR_TI: make available for am33xx as well
pch_gbe: fix error handling in pch_gbe_up()
b43: Fix oops on unload when firmware not found
mwifiex: clean up scan state on error
mwifiex: return -EBUSY if specific scan request cannot be honored
brcmfmac: fix potential NULL dereference
Revert "ath9k_hw: Updated AR9003 tx gain table for 5GHz"
ath9k_htc: Add PID/VID for a Ubiquiti WiFiStation
rt2x00: usb: fix reset resume
rtlwifi: pass rx setup error code to caller
...
|
|
The code to allow EAPOL frames even when the station
isn't yet marked associated needs to check that the
incoming frame is long enough and due to paged RX it
also can't assume skb->data contains the right data,
it must use skb_copy_bits(). Fix this to avoid using
data that doesn't really exist.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
A number of places in the mesh code don't check that
the frame data is present and in the skb header when
trying to access. Add those checks and the necessary
pskb_may_pull() calls. This prevents accessing data
that doesn't actually exist.
To do this, export ieee80211_get_mesh_hdrlen() to be
able to use it in mac80211.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Due to pskb_may_pull() checking the skb length, all
non-management frames are checked on input whether
their 802.11 header is fully present. Also add that
check for management frames and remove a check that
is now duplicate. This prevents accessing skb data
beyond the frame end.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The mesh header can have address extension by a 4th
or a 5th and 6th address, but never both. Drop such
frames in 802.11 -> 802.3 conversion along with any
frames that have the wrong extension.
Cc: stable@vger.kernel.org
Reviewed-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The 'ssid' field of the cfg80211_ibss_params is a u8 pointer and
its length is likely to be less than IEEE80211_MAX_SSID_LEN most
of the time.
This patch fixes the ssid copy in ieee80211_ibss_join() by using
the SSID length to prevent it from reading beyond the string.
Cc: stable@vger.kernel.org
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
[rewrapped commit message, small rewording]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Per IEEE Std. 802.11-2012, Sec 8.2.4.4.1, the sequence Control field is
not present in control frames. We noticed this problem when processing
Block Ack Requests.
Cc: stable@vger.kernel.org
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Javier Lopez <jlopex@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Prior this fix, those frames were not received, nor forwarded. Fix
this to receive and not forward.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Doing otherwise is wrong, and may wreak havoc on the mpp tables,
specially if the frame is encrypted.
Cc: stable@vger.kernel.org
Reported-by: Chaoxing Lin <Chaoxing.Lin@ultra-3eti.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Commit a02e4b7dae4551(Demark default hoplimit as zero) only changes the
hoplimit checking condition and default value in ip6_dst_hoplimit, not
zeros all hoplimit default value.
Keep the zeroing ip6_template_metrics[RTAX_HOPLIMIT - 1] to force it as
const, cause as a37e6e344910(net: force dst_default_metrics to const
section)
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ceph_on_in_msg_alloc() method drops con->mutex while it allocates a
message. If that races with a timeout that resends a zillion messages and
resets the connection, and the ->alloc_msg() method returns a NULL message,
it will call ceph_msg_put(NULL) and BUG.
Fix by only calling put if msg is non-NULL.
Fixes http://tracker.newdream.net/issues/3142
Signed-off-by: Sage Weil <sage@inktank.com>
|
|
Instead of the current whitelist which accepts duplicates
only for the quiet and vendor IEs, use a blacklist of all
IEs (that we currently parse) that can't be duplicated.
This avoids detecting a beacon as corrupt in the future
when new IEs are added that can be duplicated.
Cc: stable@vger.kernel.org
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Chris Perl reports that we're seeing races between the wakeup call in
xs_error_report and the connect attempts. Basically, Chris has shown
that in certain circumstances, the call to xs_error_report causes the
rpc_task that is responsible for reconnecting to wake up early, thus
triggering a disconnect and retry.
Since the sk->sk_error_report() calls in the socket layer are always
followed by a tcp_done() in the cases where we care about waking up
the rpc_tasks, just let the state_change callbacks take responsibility
for those wake ups.
Reported-by: Chris Perl <chris.perl@gmail.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@vger.kernel.org
Tested-by: Chris Perl <chris.perl@gmail.com>
|
|
The call to xprt_disconnect_done() that is triggered by a successful
connection reset will trigger another automatic wakeup of all tasks
on the xprt->pending rpc_wait_queue. In particular it will cause an
early wake up of the task that called xprt_connect().
All we really want to do here is clear all the socket-specific state
flags, so we split that functionality out of xs_sock_mark_closed()
into a helper that can be called by xs_abort_connection()
Reported-by: Chris Perl <chris.perl@gmail.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@vger.kernel.org
Tested-by: Chris Perl <chris.perl@gmail.com>
|
|
This reverts commit 55420c24a0d4d1fce70ca713f84aa00b6b74a70e.
Now that we clear the connected flag when entering TCP_CLOSE_WAIT,
the deadlock described in this commit is no longer possible.
Instead, the resulting call to xs_tcp_shutdown() can interfere
with pending reconnection attempts.
Reported-by: Chris Perl <chris.perl@gmail.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@vger.kernel.org
Tested-by: Chris Perl <chris.perl@gmail.com>
|
|
This is needed to ensure that we call xprt_connect() upon the next
call to call_connect().
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@vger.kernel.org
Tested-by: Chris Perl <chris.perl@gmail.com>
|
|
A packet with an invalid ack_seq may cause a TCP Fast Open socket to switch
to the unexpected TCP_CLOSING state, triggering a BUG_ON kernel panic.
When a FIN packet with an invalid ack_seq# arrives at a socket in
the TCP_FIN_WAIT1 state, rather than discarding the packet, the current
code will accept the FIN, causing state transition to TCP_CLOSING.
This may be a small deviation from RFC793, which seems to say that the
packet should be dropped. Unfortunately I did not expect this case for
Fast Open hence it will trigger a BUG_ON panic.
It turns out there is really nothing bad about a TFO socket going into
TCP_CLOSING state so I could just remove the BUG_ON statements. But after
some thought I think it's better to treat this case like TCP_SYN_RECV
and return a RST to the confused peer who caused the unacceptable ack_seq
to be generated in the first place.
Signed-off-by: H.K. Jerry Chu <hkchu@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Mike Kazantsev found 3.5 kernels and beyond were leaking memory,
and tracked the faulty commit to a1c7fff7e18f59e ("net:
netdev_alloc_skb() use build_skb()")
While this commit seems fine, it uncovered a bug introduced
in commit bad43ca8325 ("net: introduce skb_try_coalesce()), in function
kfree_skb_partial()"):
If head is stolen, we free the sk_buff,
without removing references on secpath (skb->sp).
So IPsec + IP defrag/reassembly (using skb coalescing), or
TCP coalescing could leak secpath objects.
Fix this bug by calling skb_release_head_state(skb) to properly
release all possible references to linked objects.
Reported-by: Mike Kazantsev <mk.fraggod@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Bisected-by: Mike Kazantsev <mk.fraggod@gmail.com>
Tested-by: Mike Kazantsev <mk.fraggod@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a bit TCPI_OPT_SYN_DATA (32) to the socket option TCP_INFO:tcpi_options.
It's set if the data in SYN (sent or received) is acked by SYN-ACK. Server or
client application can use this information to check Fast Open success rate.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After the change "Adjust semantics of rt->rt_gateway"
(commit f8126f1d51) we should properly match the nexthop when
destinations are directly connected because rt_gateway can be 0.
The rt_gateway checks in H.323 helper try to avoid the creation
of an unnecessary expectation in this call-forwarding case:
http://people.netfilter.org/zhaojingmin/h323_conntrack_nat_helper/#_Toc133598073
However, the existing code fails to avoid that in many cases,
see this thread:
http://marc.info/?l=linux-netdev&m=135043175028620&w=2
It seems it is not trivial to know from the kernel if two hosts
have to go through the firewall to communicate each other, which
is the main point of the call-forwarding filter code to avoid
creating unnecessary expectations.
So this patch just gets things the way they were as before
commit f8126f1d51.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY fixes from Greg Kroah-Hartman:
"Here are some tty and serial driver fixes for your 3.7-rc1 tree.
Again, the UABI header file fixes, and a number of build and runtime
serial driver bugfixes that solve problems people have been reporting
(the staging driver is a tty driver, hence the fixes coming in through
this tree.)
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'tty-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
staging: dgrp: check return value of alloc_tty_driver
staging: dgrp: check for NULL pointer in (un)register_proc_table
serial/8250_hp300: Missing 8250 register interface conversion bits
UAPI: (Scripted) Disintegrate include/linux/hsi
tty: serial: sccnxp: Fix bug with unterminated platform_id list
staging: serial: dgrp: Add missing #include <linux/uaccess.h>
serial: sccnxp: Allows the driver to be compiled as a module
tty: Fix bogus "callbacks suppressed" messages
net, TTY: initialize tty->driver_data before usage
|
|
Pull nfsd bugfixes from J Bruce Fields.
* 'for-3.7' of git://linux-nfs.org/~bfields/linux:
SUNRPC: Prevent kernel stack corruption on long values of flush
NLM: nlm_lookup_file() may return NLMv4-specific error codes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
Included fixes:
- Fix broadcast packet CRC calculation which can lead to ~80% broadcast packet
loss
- Fix a race condition in duplicate broadcast packet check
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tcp_ioctl() tries to take into account if tcp socket received a FIN
to report correct number bytes in receive queue.
But its flaky because if the application ate the last skb,
we return 1 instead of 0.
Correct way to detect that FIN was received is to test SOCK_DONE.
Reported-by: Elliot Hughes <enh@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On some suspend/resume operations involving wimax device, we have
noticed some intermittent memory corruptions in netlink code.
Stéphane Marchesin tracked this corruption in netlink_update_listeners()
and suggested a patch.
It appears netlink_release() should use kfree_rcu() instead of kfree()
for the listeners structure as it may be used by other cpus using RCU
protection.
netlink_release() must set to NULL the listeners pointer when
it is about to be freed.
Also have to protect netlink_update_listeners() and
netlink_has_listeners() if listeners is NULL.
Add a nl_deref_protected() lockdep helper to properly document which
locks protects us.
Reported-by: Jonathan Kliegman <kliegs@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Stéphane Marchesin <marcheu@google.com>
Cc: Sam Leffler <sleffler@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently we can not flush cached pmtu/redirect informations via
the ipv4_sysctl_rtcache_flush sysctl. We need to check the rt_genid
of the old route and reset the nh exeption if the old route is
expired when we bind a new route to a nh exeption.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
