summaryrefslogtreecommitdiffstats
path: root/net/wireless/Makefile
AgeCommit message (Collapse)AuthorFilesLines
2019-05-14wireless: Skip directory when generating certificatesMaxim Mikityanskiy1-0/+1
Commit 715a12334764 ("wireless: don't write C files on failures") drops the `test -f $$f` check. The list of targets contains the CONFIG_CFG80211_EXTRA_REGDB_KEYDIR directory itself, and this check used to filter it out. After the check was removed, the extra keydir option no longer works, failing with the following message: od: 'standard input': read error: Is a directory This commit restores the check to make extra keydir work again. Fixes: 715a12334764 ("wireless: don't write C files on failures") Signed-off-by: Maxim Mikityanskiy <maxtram95@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-11-09cfg80211: add peer measurement with FTM initiator APIJohannes Berg1-0/+1
Add a new "peer measurement" API, that can be used to measure certain things related to a peer. Right now, only implement FTM (flight time measurement) over it, but the idea is that it'll be extensible to also support measuring the necessary things to calculate e.g. angle-of-arrival for WiGig. The API is structured to have a generic list of peers and channels to measure with/on, and then for each of those a set of measurements (again, only FTM right now) to perform. Results are sent to the requesting socket, including a final complete message. Closing the controlling netlink socket will abort a running measurement. v3: - add a bit to report "final" for partial results - remove list keeping etc. and just unicast out the results to the requester (big code reduction ...) - also send complete message unicast, and as a result remove the multicast group - separate out struct cfg80211_pmsr_ftm_request_peer from struct cfg80211_pmsr_request_peer - document timeout == 0 if no timeout - disallow setting timeout nl80211 attribute to 0, must not include attribute for no timeout - make MAC address randomization optional - change num bursts exponent default to 0 (1 burst, rather rather than the old default of 15==don't care) v4: - clarify NL80211_ATTR_TIMEOUT documentation v5: - remove unnecessary nl80211 multicast/family changes - remove partial results bit/flag, final is sufficient - add max_bursts_exponent, max_ftms_per_burst to capability - rename "frames per burst" -> "FTMs per burst" v6: - rename cfg80211_pmsr_free_wdev() to cfg80211_pmsr_wdev_down() and call it in leave, so the device can't go down with any pending measurements v7: - wording fixes (Lior) - fix ftm.max_bursts_exponent to allow having the limit of 0 (Lior) v8: - copyright statements - minor coding style fixes - fix error path leak Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-12-19cfg80211: ship certificates as hex filesJohannes Berg1-20/+9
Not only does this remove the need for the hexdump code in most normal kernel builds (still there for the extra directory), but it also removes the need to ship binary files, which apparently is somewhat problematic, as Randy reported. While at it, also add the generated files to clean-files. Reported-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-12-19cfg80211: always rewrite generated files from scratchThierry Reding1-2/+2
Currently the certs C code generation appends to the generated files, which is most likely a leftover from commit 715a12334764 ("wireless: don't write C files on failures"). This causes duplicate code in the generated files if the certificates have their timestamps modified between builds and thereby trigger the generation rules. Fixes: 715a12334764 ("wireless: don't write C files on failures") Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-12-06wireless: don't write C files on failuresJohannes Berg1-10/+38
Change the scripting inside the shipped/extra certs C code generation to not write the file when there are any failures. That way, if the build aborts due to failures, we don't get into a situation where a dummy file has been created and the next build succeeds, but not with the desired output. Fixes: 90a53e4432b1 ("cfg80211: implement regdb signature checking") Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-12-06wireless: replace usage of hexdump with od/sedJohannes Berg1-2/+2
Since od/sed are in posix, hopefully there's a better chance people will have them, over hexdump. Fixes: 90a53e4432b1 ("cfg80211: implement regdb signature checking") Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-11-04Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller1-0/+1
Files removed in 'net-next' had their license header updated in 'net'. We take the remove from 'net-next'. Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-02License cleanup: add SPDX GPL-2.0 license identifier to files with no licenseGreg Kroah-Hartman1-0/+1
Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-13cfg80211: don't print log output for building shipped-certsArnd Bergmann1-2/+2
Building an allmodconfig kernel with 'make -s' now prints a single line: GEN net/wireless/shipped-certs.c Using '$(kecho)' here will skip the output with 'make -s' but otherwise keeps printing it, which is consistent with how we handle all the other output. Fixes: 90a53e4432b1 ("cfg80211: implement regdb signature checking") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-10-11cfg80211: implement regdb signature checkingJohannes Berg1-0/+22
Currently CRDA implements the signature checking, and the previous commits added the ability to load the whole regulatory database into the kernel. However, we really can't lose the signature checking, so implement it in the kernel by loading a detached signature (regulatory.db.p7s) and check it against built-in keys. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-10-11cfg80211: reg: remove support for built-in regdbJohannes Berg1-6/+0
Parsing and building C structures from a regdb is no longer needed since the "firmware" file (regulatory.db) can be linked into the kernel image to achieve the same effect. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-01-14Merge tag 'mac80211-next-for-davem-2017-01-13' of ↵David S. Miller1-0/+1
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next Johannes Berg says: ==================== For 4.11, we seem to have more than in the past few releases: * socket owner support for connections, so when the wifi manager (e.g. wpa_supplicant) is killed, connections are torn down - wpa_supplicant is critical to managing certain operations, and can opt in to this where applicable * minstrel & minstrel_ht updates to be more efficient (time and space) * set wifi_acked/wifi_acked_valid for skb->destructor use in the kernel, which was already available to userspace * don't indicate new mesh peers that might be used if there's no room to add them * multicast-to-unicast support in mac80211, for better medium usage (since unicast frames can use *much* higher rates, by ~3 orders of magnitude) * add API to read channel (frequency) limitations from DT * add infrastructure to allow randomizing public action frames for MAC address privacy (still requires driver support) * many cleanups and small improvements/fixes across the board ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2017-01-06cfg80211: support ieee80211-freq-limit DT propertyRafał Miłecki1-0/+1
This patch adds a helper for reading that new property and applying limitations of supported channels specified this way. It is used with devices that normally support a wide wireless band but in a given config are limited to some part of it (usually due to board design). For example a dual-band chipset may be able to support one band only because of used antennas. It's also common that tri-band routers have separated radios for lower and higher part of 5 GHz band and it may be impossible to say which is which without a DT info. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> [add new function to documentation, fix link] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-12-16Makefile: drop -D__CHECK_ENDIAN__ from cflagsMichael S. Tsirkin1-2/+0
That's the default now, no need for makefiles to set it. Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Kalle Valo <kvalo@codeaurora.org> Acked-by: Marcel Holtmann <marcel@holtmann.org> Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
2014-11-04cfg80211: 802.11p OCB mode handlingRostislav Lisovy1-1/+1
This patch adds new iface type (NL80211_IFTYPE_OCB) representing the OCB (Outside the Context of a BSS) mode. When establishing a connection to the network a cfg80211_join_ocb function is called (particular nl80211_command is added as well). A mandatory parameters during the ocb_join operation are 'center frequency' and 'channel width (5/10 MHz)'. Changes done in mac80211 are minimal possible required to avoid many warnings (warning: enumeration value 'NL80211_IFTYPE_OCB' not handled in switch) during compilation. Full functionality (where needed) is added in the following patch. Signed-off-by: Rostislav Lisovy <rostislav.lisovy@fel.cvut.cz> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-18cfg80211: add tracing to rdev-opsBeni Lev1-1/+3
Add tracing to make debugging cfg80211/mac80211 (or full-mac driver) interaction easier. Signed-off-by: Beni Lev <beni.lev@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Reviewed-by: Hila Gonen <hila.gonen@intel.com> Tested-by: Hila Gonen <hila.gonen@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> [add a cast to int to sizeof() to avoid warning] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-06-29cfg80211: introduce cfg80211_stop_apMichal Kazior1-1/+1
This functionality will be reused when interface is going down. Avoids code duplication. Also adds missing wdev locking. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2010-12-06cfg80211/mac80211: add mesh join/leave commandsJohannes Berg1-1/+1
Instead of tying mesh activity to interface up, add join and leave commands for mesh. Since we must be backward compatible, let cfg80211 handle joining a mesh if a mesh ID was pre-configured when the device goes up. Note that this therefore must modify mac80211 as well since mac80211 needs to lose the logic to start the mesh on interface up. We now allow querying mesh parameters before the mesh is connected, which simply returns defaults. Setting them (internally renamed to "update") is only allowed while connected. Specify them with the new mesh join command instead where needed. In mac80211, beaconing must now also follow the mesh enabled/not enabled state, which is done by testing the mesh ID. Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-21wireless: support internal statically compiled regulatory databaseJohn W. Linville1-0/+6
This patch provides infrastructure for machine translation of the regulatory rules database used by CRDA into a C data structure. It includes code for searching that database as an alternative to dynamic regulatory rules updates via CRDA. Most people should use CRDA instead of this infrastructure, but it provides a better alternative than the WIRELESS_OLD_REGULATORY infrastructure (which can now be removed). Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-07wireless: implement basic ethtool support for cfg80211 devicesJohn W. Linville1-1/+1
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-07wext: refactorJohannes Berg1-2/+6
Refactor wext to * split out iwpriv handling * split out iwspy handling * split out procfs support * allow cfg80211 to have wireless extensions compat code w/o CONFIG_WIRELESS_EXT After this, drivers need to - select WIRELESS_EXT - for wext support - select WEXT_PRIV - for iwpriv support - select WEXT_SPY - for iwspy support except cfg80211 -- which gets new hooks in wext-core.c and can then get wext handlers without CONFIG_WIRELESS_EXT. Wireless extensions procfs support is auto-selected based on PROC_FS and anything that requires the wext core (i.e. WIRELESS_EXT or CFG80211_WEXT). Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-14cfg80211: validate channel settings across interfacesJohannes Berg1-1/+2
Currently, there's a problem that affects regulatory enforcement and connection stability, in that it is possible to switch the channel while connected to a network or joined to an IBSS. The problem comes from the fact that we only validate the channel against the current interface's type, not against any other interface. Thus, you have any type of interface up, additionally bring up a monitor mode interface and switch the channel on the monitor. This will obviously also switch the channel on the other interface. The problem now is that if you do that while sending beacons for IBSS mode, you can switch to a disabled channel or a channel that doesn't allow beaconing. Combined with a managed mode interface connected to an AP instead of an IBSS interface, you can easily break the connection that way. To fix this, this patch validates any channel change with all available interfaces, and disallows such changes on secondary interfaces if another interface is connected to an AP or joined to an IBSS. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-10cfg80211: managed mode wext compatibilityJohannes Berg1-1/+1
This adds code to make it possible to use the cfg80211 connect() API with wireless extensions, and because the previous patch added emulation of that API with auth() and assoc(), by extension also supports wext on that. At the same time, removes code from mac80211 for wext, but doesn't yet clean up mac80211's mlme code more. Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-10cfg80211: connect/disconnect APISamuel Ortiz1-1/+1
This patch introduces the cfg80211 connect/disconnect API. The goal here is to run the AUTH and ASSOC steps in one call. This is needed for some fullmac cards that run both steps directly from the target, after the host driver sends a connect command. Additionally, all the new crypto parameters for connect() are now also valid for associate() -- although associate requires the IEs to be used, the information can be useful for drivers and should be given. Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-05-20mac80211/cfg80211: move wiphy specific debugfs entries to cfg80211Luis R. Rodriguez1-0/+1
This moves the cfg80211 specific stuff to new cfg80211 debugfs entries. Non-mac80211 will also get these entries now. There were only 4 which we take: rts_threshold fragmentation_threshold short_retry_limit long_retry_limit Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22cfg80211/nl80211: add IBSS APIJohannes Berg1-1/+1
This adds IBSS API along with (preliminary) wext handlers. The wext handlers can only do IBSS so you need to call them from your own wext handlers if the mode is IBSS. The nl80211 API requires * an SSID * a channel (frequency) for the case that a new IBSS has to be created It optionally supports * a flag to fix the channel * a fixed BSSID The cfg80211 code also takes care to leave the IBSS before the netdev is set down. If wireless extensions are used, it also caches values when the interface is down and instructs the driver to join when the interface is set up. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27nl80211: Event notifications for MLME eventsJouni Malinen1-1/+1
Add new nl80211 event notifications (and a new multicast group, "mlme") for informing user space about received and processed Authentication, (Re)Association Response, Deauthentication, and Disassociation frames in station and IBSS modes (i.e., MLME SAP interface primitives MLME-AUTHENTICATE.confirm, MLME-ASSOCIATE.confirm, MLME-REASSOCIATE.confirm, MLME-DEAUTHENTICATE.indicate, and MLME-DISASSOCIATE.indication). The event data is encapsulated as the 802.11 management frame since we already have the frame in that format and it includes all the needed information. This is the initial step in providing MLME SAP interface for authentication and association with nl80211. In other words, kernel code will act as the MLME and a user space application can control it as the SME. Signed-off-by: Jouni Malinen <j@w1.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27cfg80211/nl80211: remove usage of CONFIG_NL80211Reinette Chatre1-2/+1
The scan capability added to cfg80211/nl80211 introduced a dependency on nl80211 by cfg80211. We can thus no longer have just cfg80211 without nl80211. Specifically, cfg80211_scan_done() calls nl80211_send_scan_aborted() or nl80211_send_scan_done(). Now we remove the option for user to select nl80211. It will always be compiled if user selects cfg80211. Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-13cfg80211/nl80211: scanning (and mac80211 update to use it)Johannes Berg1-1/+1
This patch adds basic scan capability to cfg80211/nl80211 and changes mac80211 to use it. The BSS list that cfg80211 maintains is made driver-accessible with a private area in each BSS struct, but mac80211 doesn't yet use it. That's another large project. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-12mac80211/cfg80211: check endianness in sparse runsJohannes Berg1-0/+2
Make sure sparse checks endianness when run on mac80211/cfg80211. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Cc: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-05cfg80211: handle SIOCGIWNAMEJohannes Berg1-0/+1
This patch moves the SIOCGIWNAME handling from mac80211 to cfg80211. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-11-21lib80211: absorb crypto bits from net/ieee80211John W. Linville1-0/+3
These bits are shared already between ipw2x00 and hostap, and could probably be shared both more cleanly and with other drivers. This commit simply relocates the code to lib80211 and adjusts the drivers appropriately. Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-10-31wireless: consolidate on a single escape_essid implementationJohn W. Linville1-0/+1
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-02-29cfg80211 API for channels/bitrates, mac80211 and driver conversionJohannes Berg1-1/+1
This patch creates new cfg80211 wiphy API for channel and bitrate registration and converts mac80211 and drivers to the new API. The old mac80211 API is completely ripped out. All drivers (except ath5k) are updated to the new API, in many cases I expect that optimisations can be done. Along with the regulatory code I've also ripped out the IEEE80211_HW_DEFAULT_REG_DOMAIN_CONFIGURED flag, I believe it to be unnecessary if the hardware simply gives us whatever channels it wants to support and we then enable/disable them as required, which is pretty much required for travelling. Additionally, the patch adds proper "basic" rate handling for STA mode interface, AP mode interface will have to have new API added to allow userspace to set the basic rate set, currently it'll be empty... However, the basic rate handling will need to be moved to the BSS conf stuff. I do expect there to be bugs in this, especially wrt. transmit power handling where I'm basically clueless about how it should work. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[NL80211]: add netlink interface to cfg80211Johannes Berg1-0/+1
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-07-12[PATCH] cfg80211: Radiotap parserAndy Green1-1/+1
Generic code to walk through the fields in a radiotap header, accounting for nasties like extended "field present" bitfields and alignment rules Signed-off-by: Andy Green <andy@warmcat.com> Signed-off-by: Jiri Benc <jbenc@suse.cz> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-04-26[WEXT]: Move to net/wirelessJohannes Berg1-0/+1
This patch moves dev/core/wireless.c to net/wireless/wext.c. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25[WIRELESS] cfg80211: New wireless config infrastructure.Johannes Berg1-1/+3
This patch creates the core cfg80211 code along with some sysfs bits. This is a stripped down version to allow mac80211 to function, but doesn't include any configuration yet except for creating and removing virtual interfaces. This patch includes the nl80211 header file but it only contains the interface types which the cfg80211 interface for creating virtual interfaces relies on. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25[WIRELESS]: Refactor wireless Kconfig.Johannes Berg1-0/+1
This patch refactors the wireless Kconfig all over and already introduces net/wireless/Kconfig with just the WEXT bit for now, the cfg80211 patch will add to that as well. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>