summaryrefslogtreecommitdiffstats
path: root/net/ncsi/ncsi-manage.c
AgeCommit message (Collapse)AuthorFilesLines
2022-06-23net/ncsi: use proper "mellanox" DT vendor prefixKrzysztof Kozlowski1-1/+2
"mlx" Devicetree vendor prefix is not documented and instead "mellanox" should be used. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20220622115416.7400-1-krzysztof.kozlowski@linaro.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-01-15all: replace find_next{,_zero}_bit with find_first{,_zero}_bit where appropriateYury Norov1-2/+2
find_first{,_zero}_bit is a more effective analogue of 'next' version if start == 0. This patch replaces 'next' with 'first' where things look trivial. Signed-off-by: Yury Norov <yury.norov@gmail.com> Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
2021-09-01net/ncsi: add get MAC address command to get Intel i210 MAC addressIvan Mikhaylov1-1/+24
This patch adds OEM Intel GMA command and response handler for it. Signed-off-by: Brad Ho <Brad_Ho@phoenix.com> Signed-off-by: Paul Fertser <fercerpav@gmail.com> Signed-off-by: Ivan Mikhaylov <i.mikhaylov@yadro.com> Link: https://lore.kernel.org/r/20210830171806.119857-2-i.mikhaylov@yadro.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-07-08net/ncsi: add NCSI Intel OEM command to keep PHY upIvan Mikhaylov1-0/+45
This allows to keep PHY link up and prevents any channel resets during the host load. It is KEEP_PHY_LINK_UP option(Veto bit) in i210 datasheet which block PHY reset and power state changes. Signed-off-by: Ivan Mikhaylov <i.mikhaylov@yadro.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-08net/ncsi: fix restricted cast warning of sparseIvan Mikhaylov1-3/+3
Sparse reports: net/ncsi/ncsi-rsp.c:406:24: warning: cast to restricted __be32 net/ncsi/ncsi-manage.c:732:33: warning: cast to restricted __be32 net/ncsi/ncsi-manage.c:756:25: warning: cast to restricted __be32 net/ncsi/ncsi-manage.c:779:25: warning: cast to restricted __be32 Signed-off-by: Ivan Mikhaylov <i.mikhaylov@yadro.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-07net/ncsi: Fix spelling mistakesZheng Yongjun1-1/+1
Fix some spelling mistakes in comments: constuct ==> construct chanels ==> channels Detination ==> Destination Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-30net/ncsi: Avoid channel_monitor hrtimer deadlockMilton Miller1-7/+13
Calling ncsi_stop_channel_monitor from channel_monitor is a guaranteed deadlock on SMP because stop calls del_timer_sync on the timer that invoked channel_monitor as its timer function. Recognise the inherent race of marking the monitor disabled before deleting the timer by just returning if enable was cleared. After a timeout (the default case -- reset to START when response received) just mark the monitor.enabled false. If the channel has an entry on the channel_queue list, or if the state is not ACTIVE or INACTIVE, then warn and mark the timer stopped and don't restart, as the locking is broken somehow. Fixes: 0795fb2021f0 ("net/ncsi: Stop monitor if channel times out or is inactive") Signed-off-by: Milton Miller <miltonm@us.ibm.com> Signed-off-by: Eddie James <eajames@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-11-12net/ncsi: Fix netlink registrationJoel Stanley1-5/+0
If a user unbinds and re-binds a NC-SI aware driver the kernel will attempt to register the netlink interface at runtime. The structure is marked __ro_after_init so registration fails spectacularly at this point. # echo 1e660000.ethernet > /sys/bus/platform/drivers/ftgmac100/unbind # echo 1e660000.ethernet > /sys/bus/platform/drivers/ftgmac100/bind ftgmac100 1e660000.ethernet: Read MAC address 52:54:00:12:34:56 from chip ftgmac100 1e660000.ethernet: Using NCSI interface 8<--- cut here --- Unable to handle kernel paging request at virtual address 80a8f858 pgd = 8c768dd6 [80a8f858] *pgd=80a0841e(bad) Internal error: Oops: 80d [#1] SMP ARM CPU: 0 PID: 116 Comm: sh Not tainted 5.10.0-rc3-next-20201111-00003-gdd25b227ec1e #51 Hardware name: Generic DT based system PC is at genl_register_family+0x1f8/0x6d4 LR is at 0xff26ffff pc : [<8073f930>] lr : [<ff26ffff>] psr: 20000153 sp : 8553bc80 ip : 81406244 fp : 8553bd04 r10: 8085d12c r9 : 80a8f73c r8 : 85739000 r7 : 00000017 r6 : 80a8f860 r5 : 80c8ab98 r4 : 80a8f858 r3 : 00000000 r2 : 00000000 r1 : 81406130 r0 : 00000017 Flags: nzCv IRQs on FIQs off Mode SVC_32 ISA ARM Segment none Control: 00c5387d Table: 85524008 DAC: 00000051 Process sh (pid: 116, stack limit = 0x1f1988d6) ... Backtrace: [<8073f738>] (genl_register_family) from [<80860ac0>] (ncsi_init_netlink+0x20/0x48) r10:8085d12c r9:80c8fb0c r8:85739000 r7:00000000 r6:81218000 r5:85739000 r4:8121c000 [<80860aa0>] (ncsi_init_netlink) from [<8085d740>] (ncsi_register_dev+0x1b0/0x210) r5:8121c400 r4:8121c000 [<8085d590>] (ncsi_register_dev) from [<805a8060>] (ftgmac100_probe+0x6e0/0x778) r10:00000004 r9:80950228 r8:8115bc10 r7:8115ab00 r6:9eae2c24 r5:813b6f88 r4:85739000 [<805a7980>] (ftgmac100_probe) from [<805355ec>] (platform_drv_probe+0x58/0xa8) r9:80c76bb0 r8:00000000 r7:80cd4974 r6:80c76bb0 r5:8115bc10 r4:00000000 [<80535594>] (platform_drv_probe) from [<80532d58>] (really_probe+0x204/0x514) r7:80cd4974 r6:00000000 r5:80cd4868 r4:8115bc10 Jakub pointed out that ncsi_register_dev is obviously broken, because there is only one family so it would never work if there was more than one ncsi netdev. Fix the crash by registering the netlink family once on boot, and drop the code to unregister it. Fixes: 955dc68cb9b2 ("net/ncsi: Add generic netlink family") Signed-off-by: Joel Stanley <joel@jms.id.au> Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Link: https://lore.kernel.org/r/20201112061210.914621-1-joel@jms.id.au Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-08-23treewide: Use fallthrough pseudo-keywordGustavo A. R. Silva1-2/+2
Replace the existing /* fall through */ comments and its variants with the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary fall-through markings when it is the case. [1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
2020-01-09net/ncsi: Support for multi host mellanox cardVijay Khemka1-0/+69
Multi host Mellanox cards require MAC affinity to be set before receiving any config commands. All config commands should also have unicast address for source address in command header. Adding GMA and SMAF(Set Mac Affinity) for Mellanox card and call these in channel probe state machine if it is defined in device tree. Signed-off-by: Vijay Khemka <vijaykhemka@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-30net/ncsi: Fix gma flag setting after responseVijay Khemka1-3/+0
gma_flag was set at the time of GMA command request but it should only be set after getting successful response. Movinng this flag setting in GMA response handler. This flag is used mainly for not repeating GMA command once received MAC address. Signed-off-by: Vijay Khemka <vijaykhemka@fb.com> Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-09-19net/ncsi: Disable global multicast filterVijay Khemka1-87/+11
Disabling multicast filtering from NCSI if it is supported. As it should not filter any multicast packets. In current code, multicast filter is enabled and with an exception of optional field supported by device are disabled filtering. Mainly I see if goal is to disable filtering for IPV6 packets then let it disabled for every other types as well. As we are seeing issues with LLDP not working with this enabled filtering. And there are other issues with IPV6. By Disabling this multicast completely, it is working for both IPV6 as well as LLDP. Signed-off-by: Vijay Khemka <vijaykhemka@fb.com> Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
2019-05-30treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 152Thomas Gleixner1-5/+1
Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 3029 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-11-27net/ncsi: Add NCSI Mellanox OEM commandVijay Khemka1-1/+27
This patch adds OEM Mellanox commands and response handling. It also defines OEM Get MAC Address handler to get and configure the device. ncsi_oem_gma_handler_mlx: This handler send NCSI mellanox command for getting mac address. ncsi_rsp_handler_oem_mlx: This handles response received for all mellanox OEM commands. ncsi_rsp_handler_oem_mlx_gma: This handles get mac address response and set it to device. Signed-off-by: Vijay Khemka <vijaykhemka@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-17net/ncsi: Configure multi-package, multi-channel modes with failoverSamuel Mendoza-Jonas1-45/+219
This patch extends the ncsi-netlink interface with two new commands and three new attributes to configure multiple packages and/or channels at once, and configure specific failover modes. NCSI_CMD_SET_PACKAGE mask and NCSI_CMD_SET_CHANNEL_MASK set a whitelist of packages or channels allowed to be configured with the NCSI_ATTR_PACKAGE_MASK and NCSI_ATTR_CHANNEL_MASK attributes respectively. If one of these whitelists is set only packages or channels matching the whitelist are considered for the channel queue in ncsi_choose_active_channel(). These commands may also use the NCSI_ATTR_MULTI_FLAG to signal that multiple packages or channels may be configured simultaneously. NCSI hardware arbitration (HWA) must be available in order to enable multi-package mode. Multi-channel mode is always available. If the NCSI_ATTR_CHANNEL_ID attribute is present in the NCSI_CMD_SET_CHANNEL_MASK command the it sets the preferred channel as with the NCSI_CMD_SET_INTERFACE command. The combination of preferred channel and channel whitelist defines a primary channel and the allowed failover channels. If the NCSI_ATTR_MULTI_FLAG attribute is also present then the preferred channel is configured for Tx/Rx and the other channels are enabled only for Rx. Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-17net/ncsi: Reset channel state in ncsi_start_dev()Samuel Mendoza-Jonas1-6/+105
When the NCSI driver is stopped with ncsi_stop_dev() the channel monitors are stopped and the state set to "inactive". However the channels are still configured and active from the perspective of the network controller. We should suspend each active channel but in the context of ncsi_stop_dev() the transmit queue has been or is about to be stopped so we won't have time to do so. Instead when ncsi_start_dev() is called if the NCSI topology has already been probed then call ncsi_reset_dev() to suspend any channels that were previously active. This resets the network controller to a known state, provides an up to date view of channel link state, and makes sure that mode flags such as NCSI_MODE_TX_ENABLE are properly reset. In addition to ncsi_start_dev() use ncsi_reset_dev() in ncsi-netlink.c to update the channel configuration more cleanly. Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-17net/ncsi: Don't mark configured channels inactiveSamuel Mendoza-Jonas1-2/+1
The concepts of a channel being 'active' and it having link are slightly muddled in the NCSI driver. Tweak this slightly so that NCSI_CHANNEL_ACTIVE represents a channel that has been configured and enabled, and NCSI_CHANNEL_INACTIVE represents a de-configured channel. This distinction is important because a channel can be 'active' but have its link down; in this case the channel may still need to be configured so that it may receive AEN link-state-change packets. Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-17net/ncsi: Don't deselect package in suspend if activeSamuel Mendoza-Jonas1-2/+13
When a package is deselected all channels of that package cease communication. If there are other channels active on the package of the suspended channel this will disable them as well, so only send a deselect-package command if no other channels are active. Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-17net/ncsi: Probe single packages to avoid conflictSamuel Mendoza-Jonas1-55/+30
Currently the NCSI driver sends a select-package command to all possible packages simultaneously to discover what packages are available. However at this stage in the probe process the driver does not know if hardware arbitration is available: if it isn't then this process could cause collisions on the RMII bus when packages try to respond. Update the probe loop to probe each package one by one, and once complete check if HWA is universally supported. Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-17net/ncsi: Don't enable all channels when HWA availableSamuel Mendoza-Jonas1-46/+4
NCSI hardware arbitration allows multiple packages to be enabled at once and share the same wiring. If the NCSI driver recognises that HWA is available it unconditionally enables all packages and channels; but that is a configuration decision rather than something required by HWA. Additionally the current implementation will not failover on link events which can cause connectivity to be lost unless the interface is manually bounced. Retain basic HWA support but remove the separate configuration path to enable all channels, leaving this to be handled by a later implementation. Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-17net/ncsi: Add NCSI Broadcom OEM commandVijay Khemka1-0/+82
This patch adds OEM Broadcom commands and response handling. It also defines OEM Get MAC Address handler to get and configure the device. ncsi_oem_gma_handler_bcm: This handler send NCSI broadcom command for getting mac address. ncsi_rsp_handler_oem_bcm: This handles response received for all broadcom OEM commands. ncsi_rsp_handler_oem_bcm_gma: This handles get mac address response and set it to device. Signed-off-by: Vijay Khemka <vijaykhemka@fb.com> Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-15net/ncsi: Extend NC-SI Netlink interface to allow user space to send NC-SI ↵Justin.Lee1@Dell.com1-0/+16
command The new command (NCSI_CMD_SEND_CMD) is added to allow user space application to send NC-SI command to the network card. Also, add a new attribute (NCSI_ATTR_DATA) for transferring request and response. The work flow is as below. Request: User space application -> Netlink interface (msg) -> new Netlink handler - ncsi_send_cmd_nl() -> ncsi_xmit_cmd() Response: Response received - ncsi_rcv_rsp() -> internal response handler - ncsi_rsp_handler_xxx() -> ncsi_rsp_handler_netlink() -> ncsi_send_netlink_rsp () -> Netlink interface (msg) -> user space application Command timeout - ncsi_request_timeout() -> ncsi_send_netlink_timeout () -> Netlink interface (msg with zero data length) -> user space application Error: Error detected -> ncsi_send_netlink_err () -> Netlink interface (err msg) -> user space application Signed-off-by: Justin Lee <justin.lee1@dell.com> Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-20net/ncsi: Use netdev_dbg for debug messagesJoel Stanley1-18/+15
This moves all of the netdev_printk(KERN_DEBUG, ...) messages over to netdev_dbg. As Joe explains: > netdev_dbg is not included in object code unless > DEBUG is defined or CONFIG_DYNAMIC_DEBUG is set. > And then, it is not emitted into the log unless > DEBUG is set or this specific netdev_dbg is enabled > via the dynamic debug control file. Which is what we're after in this case. Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-20net/ncsi: Drop no more channels messageJoel Stanley1-2/+0
This does not provide useful information. As the ncsi maintainer said: > either we get a channel or broadcom has gone out to lunch Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-20net/ncsi: Silence debug messagesJoel Stanley1-7/+7
In normal operation we see this series of messages as the host drives the network device: ftgmac100 1e660000.ethernet eth0: NCSI: LSC AEN - channel 0 state down ftgmac100 1e660000.ethernet eth0: NCSI: suspending channel 0 ftgmac100 1e660000.ethernet eth0: NCSI: configuring channel 0 ftgmac100 1e660000.ethernet eth0: NCSI: channel 0 link down after config ftgmac100 1e660000.ethernet eth0: NCSI interface down ftgmac100 1e660000.ethernet eth0: NCSI: LSC AEN - channel 0 state up ftgmac100 1e660000.ethernet eth0: NCSI: configuring channel 0 ftgmac100 1e660000.ethernet eth0: NCSI interface up ftgmac100 1e660000.ethernet eth0: NCSI: LSC AEN - channel 0 state down ftgmac100 1e660000.ethernet eth0: NCSI: suspending channel 0 ftgmac100 1e660000.ethernet eth0: NCSI: configuring channel 0 ftgmac100 1e660000.ethernet eth0: NCSI: channel 0 link down after config ftgmac100 1e660000.ethernet eth0: NCSI interface down ftgmac100 1e660000.ethernet eth0: NCSI: LSC AEN - channel 0 state up ftgmac100 1e660000.ethernet eth0: NCSI: configuring channel 0 ftgmac100 1e660000.ethernet eth0: NCSI interface up This makes all of these messages netdev_dbg. They are still useful to debug eg. misbehaving network device firmware, but we do not need them filling up the kernel logs in normal operation. Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-17net/ncsi: Refactor MAC, VLAN filtersSamuel Mendoza-Jonas1-174/+52
The NCSI driver defines a generic ncsi_channel_filter struct that can be used to store arbitrarily formatted filters, and several generic methods of accessing data stored in such a filter. However in both the driver and as defined in the NCSI specification there are only two actual filters: VLAN ID filters and MAC address filters. The splitting of the MAC filter into unicast, multicast, and mixed is also technically not necessary as these are stored in the same location in hardware. To save complexity, particularly in the set up and accessing of these generic filters, remove them in favour of two specific structs. These can be acted on directly and do not need several generic helper functions to use. This also fixes a memory error found by KASAN on ARM32 (which is not upstream yet), where response handlers accessing a filter's data field could write past allocated memory. [ 114.926512] ================================================================== [ 114.933861] BUG: KASAN: slab-out-of-bounds in ncsi_configure_channel+0x4b8/0xc58 [ 114.941304] Read of size 2 at addr 94888558 by task kworker/0:2/546 [ 114.947593] [ 114.949146] CPU: 0 PID: 546 Comm: kworker/0:2 Not tainted 4.16.0-rc6-00119-ge156398bfcad #13 ... [ 115.170233] The buggy address belongs to the object at 94888540 [ 115.170233] which belongs to the cache kmalloc-32 of size 32 [ 115.181917] The buggy address is located 24 bytes inside of [ 115.181917] 32-byte region [94888540, 94888560) [ 115.192115] The buggy address belongs to the page: [ 115.196943] page:9eeac100 count:1 mapcount:0 mapping:94888000 index:0x94888fc1 [ 115.204200] flags: 0x100(slab) [ 115.207330] raw: 00000100 94888000 94888fc1 0000003f 00000001 9eea2014 9eecaa74 96c003e0 [ 115.215444] page dumped because: kasan: bad access detected [ 115.221036] [ 115.222544] Memory state around the buggy address: [ 115.227384] 94888400: fb fb fb fb fc fc fc fc 04 fc fc fc fc fc fc fc [ 115.233959] 94888480: 00 00 00 fc fc fc fc fc 00 04 fc fc fc fc fc fc [ 115.240529] >94888500: 00 00 04 fc fc fc fc fc 00 00 04 fc fc fc fc fc [ 115.247077] ^ [ 115.252523] 94888580: 00 04 fc fc fc fc fc fc 06 fc fc fc fc fc fc fc [ 115.259093] 94888600: 00 00 06 fc fc fc fc fc 00 00 04 fc fc fc fc fc [ 115.265639] ================================================================== Reported-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-05net/ncsi: Add generic netlink familySamuel Mendoza-Jonas1-4/+26
Add a generic netlink family for NCSI. This supports three commands; NCSI_CMD_PKG_INFO which returns information on packages and their associated channels, NCSI_CMD_SET_INTERFACE which allows a specific package or package/channel combination to be set as the preferred choice, and NCSI_CMD_CLEAR_INTERFACE which clears any preferred setting. Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-21treewide: setup_timer() -> timer_setup() (2 field)Kees Cook1-4/+3
This converts all remaining setup_timer() calls that use a nested field to reach a struct timer_list. Coccinelle does not have an easy way to match multiple fields, so a new script is needed to change the matches of "&_E->_timer" into "&_E->_field1._timer" in all the rules. spatch --very-quiet --all-includes --include-headers \ -I ./arch/x86/include -I ./arch/x86/include/generated \ -I ./include -I ./arch/x86/include/uapi \ -I ./arch/x86/include/generated/uapi -I ./include/uapi \ -I ./include/generated/uapi --include ./include/linux/kconfig.h \ --dir . \ --cocci-file ~/src/data/timer_setup-2fields.cocci @fix_address_of depends@ expression e; @@ setup_timer( -&(e) +&e , ...) // Update any raw setup_timer() usages that have a NULL callback, but // would otherwise match change_timer_function_usage, since the latter // will update all function assignments done in the face of a NULL // function initialization in setup_timer(). @change_timer_function_usage_NULL@ expression _E; identifier _field1; identifier _timer; type _cast_data; @@ ( -setup_timer(&_E->_field1._timer, NULL, _E); +timer_setup(&_E->_field1._timer, NULL, 0); | -setup_timer(&_E->_field1._timer, NULL, (_cast_data)_E); +timer_setup(&_E->_field1._timer, NULL, 0); | -setup_timer(&_E._field1._timer, NULL, &_E); +timer_setup(&_E._field1._timer, NULL, 0); | -setup_timer(&_E._field1._timer, NULL, (_cast_data)&_E); +timer_setup(&_E._field1._timer, NULL, 0); ) @change_timer_function_usage@ expression _E; identifier _field1; identifier _timer; struct timer_list _stl; identifier _callback; type _cast_func, _cast_data; @@ ( -setup_timer(&_E->_field1._timer, _callback, _E); +timer_setup(&_E->_field1._timer, _callback, 0); | -setup_timer(&_E->_field1._timer, &_callback, _E); +timer_setup(&_E->_field1._timer, _callback, 0); | -setup_timer(&_E->_field1._timer, _callback, (_cast_data)_E); +timer_setup(&_E->_field1._timer, _callback, 0); | -setup_timer(&_E->_field1._timer, &_callback, (_cast_data)_E); +timer_setup(&_E->_field1._timer, _callback, 0); | -setup_timer(&_E->_field1._timer, (_cast_func)_callback, _E); +timer_setup(&_E->_field1._timer, _callback, 0); | -setup_timer(&_E->_field1._timer, (_cast_func)&_callback, _E); +timer_setup(&_E->_field1._timer, _callback, 0); | -setup_timer(&_E->_field1._timer, (_cast_func)_callback, (_cast_data)_E); +timer_setup(&_E->_field1._timer, _callback, 0); | -setup_timer(&_E->_field1._timer, (_cast_func)&_callback, (_cast_data)_E); +timer_setup(&_E->_field1._timer, _callback, 0); | -setup_timer(&_E._field1._timer, _callback, (_cast_data)_E); +timer_setup(&_E._field1._timer, _callback, 0); | -setup_timer(&_E._field1._timer, _callback, (_cast_data)&_E); +timer_setup(&_E._field1._timer, _callback, 0); | -setup_timer(&_E._field1._timer, &_callback, (_cast_data)_E); +timer_setup(&_E._field1._timer, _callback, 0); | -setup_timer(&_E._field1._timer, &_callback, (_cast_data)&_E); +timer_setup(&_E._field1._timer, _callback, 0); | -setup_timer(&_E._field1._timer, (_cast_func)_callback, (_cast_data)_E); +timer_setup(&_E._field1._timer, _callback, 0); | -setup_timer(&_E._field1._timer, (_cast_func)_callback, (_cast_data)&_E); +timer_setup(&_E._field1._timer, _callback, 0); | -setup_timer(&_E._field1._timer, (_cast_func)&_callback, (_cast_data)_E); +timer_setup(&_E._field1._timer, _callback, 0); | -setup_timer(&_E._field1._timer, (_cast_func)&_callback, (_cast_data)&_E); +timer_setup(&_E._field1._timer, _callback, 0); | _E->_field1._timer@_stl.function = _callback; | _E->_field1._timer@_stl.function = &_callback; | _E->_field1._timer@_stl.function = (_cast_func)_callback; | _E->_field1._timer@_stl.function = (_cast_func)&_callback; | _E._field1._timer@_stl.function = _callback; | _E._field1._timer@_stl.function = &_callback; | _E._field1._timer@_stl.function = (_cast_func)_callback; | _E._field1._timer@_stl.function = (_cast_func)&_callback; ) // callback(unsigned long arg) @change_callback_handle_cast depends on change_timer_function_usage@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._field1; identifier change_timer_function_usage._timer; type _origtype; identifier _origarg; type _handletype; identifier _handle; @@ void _callback( -_origtype _origarg +struct timer_list *t ) { ( ... when != _origarg _handletype *_handle = -(_handletype *)_origarg; +from_timer(_handle, t, _field1._timer); ... when != _origarg | ... when != _origarg _handletype *_handle = -(void *)_origarg; +from_timer(_handle, t, _field1._timer); ... when != _origarg | ... when != _origarg _handletype *_handle; ... when != _handle _handle = -(_handletype *)_origarg; +from_timer(_handle, t, _field1._timer); ... when != _origarg | ... when != _origarg _handletype *_handle; ... when != _handle _handle = -(void *)_origarg; +from_timer(_handle, t, _field1._timer); ... when != _origarg ) } // callback(unsigned long arg) without existing variable @change_callback_handle_cast_no_arg depends on change_timer_function_usage && !change_callback_handle_cast@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._field1; identifier change_timer_function_usage._timer; type _origtype; identifier _origarg; type _handletype; @@ void _callback( -_origtype _origarg +struct timer_list *t ) { + _handletype *_origarg = from_timer(_origarg, t, _field1._timer); + ... when != _origarg - (_handletype *)_origarg + _origarg ... when != _origarg } // Avoid already converted callbacks. @match_callback_converted depends on change_timer_function_usage && !change_callback_handle_cast && !change_callback_handle_cast_no_arg@ identifier change_timer_function_usage._callback; identifier t; @@ void _callback(struct timer_list *t) { ... } // callback(struct something *handle) @change_callback_handle_arg depends on change_timer_function_usage && !match_callback_converted && !change_callback_handle_cast && !change_callback_handle_cast_no_arg@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._field1; identifier change_timer_function_usage._timer; type _handletype; identifier _handle; @@ void _callback( -_handletype *_handle +struct timer_list *t ) { + _handletype *_handle = from_timer(_handle, t, _field1._timer); ... } // If change_callback_handle_arg ran on an empty function, remove // the added handler. @unchange_callback_handle_arg depends on change_timer_function_usage && change_callback_handle_arg@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._field1; identifier change_timer_function_usage._timer; type _handletype; identifier _handle; identifier t; @@ void _callback(struct timer_list *t) { - _handletype *_handle = from_timer(_handle, t, _field1._timer); } // We only want to refactor the setup_timer() data argument if we've found // the matching callback. This undoes changes in change_timer_function_usage. @unchange_timer_function_usage depends on change_timer_function_usage && !change_callback_handle_cast && !change_callback_handle_cast_no_arg && !change_callback_handle_arg@ expression change_timer_function_usage._E; identifier change_timer_function_usage._field1; identifier change_timer_function_usage._timer; identifier change_timer_function_usage._callback; type change_timer_function_usage._cast_data; @@ ( -timer_setup(&_E->_field1._timer, _callback, 0); +setup_timer(&_E->_field1._timer, _callback, (_cast_data)_E); | -timer_setup(&_E._field1._timer, _callback, 0); +setup_timer(&_E._field1._timer, _callback, (_cast_data)&_E); ) // If we fixed a callback from a .function assignment, fix the // assignment cast now. @change_timer_function_assignment depends on change_timer_function_usage && (change_callback_handle_cast || change_callback_handle_cast_no_arg || change_callback_handle_arg)@ expression change_timer_function_usage._E; identifier change_timer_function_usage._field1; identifier change_timer_function_usage._timer; identifier change_timer_function_usage._callback; type _cast_func; typedef TIMER_FUNC_TYPE; @@ ( _E->_field1._timer.function = -_callback +(TIMER_FUNC_TYPE)_callback ; | _E->_field1._timer.function = -&_callback +(TIMER_FUNC_TYPE)_callback ; | _E->_field1._timer.function = -(_cast_func)_callback; +(TIMER_FUNC_TYPE)_callback ; | _E->_field1._timer.function = -(_cast_func)&_callback +(TIMER_FUNC_TYPE)_callback ; | _E._field1._timer.function = -_callback +(TIMER_FUNC_TYPE)_callback ; | _E._field1._timer.function = -&_callback; +(TIMER_FUNC_TYPE)_callback ; | _E._field1._timer.function = -(_cast_func)_callback +(TIMER_FUNC_TYPE)_callback ; | _E._field1._timer.function = -(_cast_func)&_callback +(TIMER_FUNC_TYPE)_callback ; ) // Sometimes timer functions are called directly. Replace matched args. @change_timer_function_calls depends on change_timer_function_usage && (change_callback_handle_cast || change_callback_handle_cast_no_arg || change_callback_handle_arg)@ expression _E; identifier change_timer_function_usage._field1; identifier change_timer_function_usage._timer; identifier change_timer_function_usage._callback; type _cast_data; @@ _callback( ( -(_cast_data)_E +&_E->_field1._timer | -(_cast_data)&_E +&_E._field1._timer | -_E +&_E->_field1._timer ) ) // If a timer has been configured without a data argument, it can be // converted without regard to the callback argument, since it is unused. @match_timer_function_unused_data@ expression _E; identifier _field1; identifier _timer; identifier _callback; @@ ( -setup_timer(&_E->_field1._timer, _callback, 0); +timer_setup(&_E->_field1._timer, _callback, 0); | -setup_timer(&_E->_field1._timer, _callback, 0L); +timer_setup(&_E->_field1._timer, _callback, 0); | -setup_timer(&_E->_field1._timer, _callback, 0UL); +timer_setup(&_E->_field1._timer, _callback, 0); | -setup_timer(&_E._field1._timer, _callback, 0); +timer_setup(&_E._field1._timer, _callback, 0); | -setup_timer(&_E._field1._timer, _callback, 0L); +timer_setup(&_E._field1._timer, _callback, 0); | -setup_timer(&_E._field1._timer, _callback, 0UL); +timer_setup(&_E._field1._timer, _callback, 0); | -setup_timer(&_field1._timer, _callback, 0); +timer_setup(&_field1._timer, _callback, 0); | -setup_timer(&_field1._timer, _callback, 0L); +timer_setup(&_field1._timer, _callback, 0); | -setup_timer(&_field1._timer, _callback, 0UL); +timer_setup(&_field1._timer, _callback, 0); | -setup_timer(_field1._timer, _callback, 0); +timer_setup(_field1._timer, _callback, 0); | -setup_timer(_field1._timer, _callback, 0L); +timer_setup(_field1._timer, _callback, 0); | -setup_timer(_field1._timer, _callback, 0UL); +timer_setup(_field1._timer, _callback, 0); ) @change_callback_unused_data depends on match_timer_function_unused_data@ identifier match_timer_function_unused_data._callback; type _origtype; identifier _origarg; @@ void _callback( -_origtype _origarg +struct timer_list *unused ) { ... when != _origarg } Signed-off-by: Kees Cook <keescook@chromium.org>
2017-11-21treewide: setup_timer() -> timer_setup()Kees Cook1-5/+3
This converts all remaining cases of the old setup_timer() API into using timer_setup(), where the callback argument is the structure already holding the struct timer_list. These should have no behavioral changes, since they just change which pointer is passed into the callback with the same available pointers after conversion. It handles the following examples, in addition to some other variations. Casting from unsigned long: void my_callback(unsigned long data) { struct something *ptr = (struct something *)data; ... } ... setup_timer(&ptr->my_timer, my_callback, ptr); and forced object casts: void my_callback(struct something *ptr) { ... } ... setup_timer(&ptr->my_timer, my_callback, (unsigned long)ptr); become: void my_callback(struct timer_list *t) { struct something *ptr = from_timer(ptr, t, my_timer); ... } ... timer_setup(&ptr->my_timer, my_callback, 0); Direct function assignments: void my_callback(unsigned long data) { struct something *ptr = (struct something *)data; ... } ... ptr->my_timer.function = my_callback; have a temporary cast added, along with converting the args: void my_callback(struct timer_list *t) { struct something *ptr = from_timer(ptr, t, my_timer); ... } ... ptr->my_timer.function = (TIMER_FUNC_TYPE)my_callback; And finally, callbacks without a data assignment: void my_callback(unsigned long data) { ... } ... setup_timer(&ptr->my_timer, my_callback, 0); have their argument renamed to verify they're unused during conversion: void my_callback(struct timer_list *unused) { ... } ... timer_setup(&ptr->my_timer, my_callback, 0); The conversion is done with the following Coccinelle script: spatch --very-quiet --all-includes --include-headers \ -I ./arch/x86/include -I ./arch/x86/include/generated \ -I ./include -I ./arch/x86/include/uapi \ -I ./arch/x86/include/generated/uapi -I ./include/uapi \ -I ./include/generated/uapi --include ./include/linux/kconfig.h \ --dir . \ --cocci-file ~/src/data/timer_setup.cocci @fix_address_of@ expression e; @@ setup_timer( -&(e) +&e , ...) // Update any raw setup_timer() usages that have a NULL callback, but // would otherwise match change_timer_function_usage, since the latter // will update all function assignments done in the face of a NULL // function initialization in setup_timer(). @change_timer_function_usage_NULL@ expression _E; identifier _timer; type _cast_data; @@ ( -setup_timer(&_E->_timer, NULL, _E); +timer_setup(&_E->_timer, NULL, 0); | -setup_timer(&_E->_timer, NULL, (_cast_data)_E); +timer_setup(&_E->_timer, NULL, 0); | -setup_timer(&_E._timer, NULL, &_E); +timer_setup(&_E._timer, NULL, 0); | -setup_timer(&_E._timer, NULL, (_cast_data)&_E); +timer_setup(&_E._timer, NULL, 0); ) @change_timer_function_usage@ expression _E; identifier _timer; struct timer_list _stl; identifier _callback; type _cast_func, _cast_data; @@ ( -setup_timer(&_E->_timer, _callback, _E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, &_callback, _E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, _callback, (_cast_data)_E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, &_callback, (_cast_data)_E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, (_cast_func)_callback, _E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, (_cast_func)&_callback, _E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, (_cast_func)_callback, (_cast_data)_E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, (_cast_func)&_callback, (_cast_data)_E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E._timer, _callback, (_cast_data)_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, _callback, (_cast_data)&_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, &_callback, (_cast_data)_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, &_callback, (_cast_data)&_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, (_cast_func)_callback, (_cast_data)_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, (_cast_func)_callback, (_cast_data)&_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, (_cast_func)&_callback, (_cast_data)_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, (_cast_func)&_callback, (_cast_data)&_E); +timer_setup(&_E._timer, _callback, 0); | _E->_timer@_stl.function = _callback; | _E->_timer@_stl.function = &_callback; | _E->_timer@_stl.function = (_cast_func)_callback; | _E->_timer@_stl.function = (_cast_func)&_callback; | _E._timer@_stl.function = _callback; | _E._timer@_stl.function = &_callback; | _E._timer@_stl.function = (_cast_func)_callback; | _E._timer@_stl.function = (_cast_func)&_callback; ) // callback(unsigned long arg) @change_callback_handle_cast depends on change_timer_function_usage@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._timer; type _origtype; identifier _origarg; type _handletype; identifier _handle; @@ void _callback( -_origtype _origarg +struct timer_list *t ) { ( ... when != _origarg _handletype *_handle = -(_handletype *)_origarg; +from_timer(_handle, t, _timer); ... when != _origarg | ... when != _origarg _handletype *_handle = -(void *)_origarg; +from_timer(_handle, t, _timer); ... when != _origarg | ... when != _origarg _handletype *_handle; ... when != _handle _handle = -(_handletype *)_origarg; +from_timer(_handle, t, _timer); ... when != _origarg | ... when != _origarg _handletype *_handle; ... when != _handle _handle = -(void *)_origarg; +from_timer(_handle, t, _timer); ... when != _origarg ) } // callback(unsigned long arg) without existing variable @change_callback_handle_cast_no_arg depends on change_timer_function_usage && !change_callback_handle_cast@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._timer; type _origtype; identifier _origarg; type _handletype; @@ void _callback( -_origtype _origarg +struct timer_list *t ) { + _handletype *_origarg = from_timer(_origarg, t, _timer); + ... when != _origarg - (_handletype *)_origarg + _origarg ... when != _origarg } // Avoid already converted callbacks. @match_callback_converted depends on change_timer_function_usage && !change_callback_handle_cast && !change_callback_handle_cast_no_arg@ identifier change_timer_function_usage._callback; identifier t; @@ void _callback(struct timer_list *t) { ... } // callback(struct something *handle) @change_callback_handle_arg depends on change_timer_function_usage && !match_callback_converted && !change_callback_handle_cast && !change_callback_handle_cast_no_arg@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._timer; type _handletype; identifier _handle; @@ void _callback( -_handletype *_handle +struct timer_list *t ) { + _handletype *_handle = from_timer(_handle, t, _timer); ... } // If change_callback_handle_arg ran on an empty function, remove // the added handler. @unchange_callback_handle_arg depends on change_timer_function_usage && change_callback_handle_arg@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._timer; type _handletype; identifier _handle; identifier t; @@ void _callback(struct timer_list *t) { - _handletype *_handle = from_timer(_handle, t, _timer); } // We only want to refactor the setup_timer() data argument if we've found // the matching callback. This undoes changes in change_timer_function_usage. @unchange_timer_function_usage depends on change_timer_function_usage && !change_callback_handle_cast && !change_callback_handle_cast_no_arg && !change_callback_handle_arg@ expression change_timer_function_usage._E; identifier change_timer_function_usage._timer; identifier change_timer_function_usage._callback; type change_timer_function_usage._cast_data; @@ ( -timer_setup(&_E->_timer, _callback, 0); +setup_timer(&_E->_timer, _callback, (_cast_data)_E); | -timer_setup(&_E._timer, _callback, 0); +setup_timer(&_E._timer, _callback, (_cast_data)&_E); ) // If we fixed a callback from a .function assignment, fix the // assignment cast now. @change_timer_function_assignment depends on change_timer_function_usage && (change_callback_handle_cast || change_callback_handle_cast_no_arg || change_callback_handle_arg)@ expression change_timer_function_usage._E; identifier change_timer_function_usage._timer; identifier change_timer_function_usage._callback; type _cast_func; typedef TIMER_FUNC_TYPE; @@ ( _E->_timer.function = -_callback +(TIMER_FUNC_TYPE)_callback ; | _E->_timer.function = -&_callback +(TIMER_FUNC_TYPE)_callback ; | _E->_timer.function = -(_cast_func)_callback; +(TIMER_FUNC_TYPE)_callback ; | _E->_timer.function = -(_cast_func)&_callback +(TIMER_FUNC_TYPE)_callback ; | _E._timer.function = -_callback +(TIMER_FUNC_TYPE)_callback ; | _E._timer.function = -&_callback; +(TIMER_FUNC_TYPE)_callback ; | _E._timer.function = -(_cast_func)_callback +(TIMER_FUNC_TYPE)_callback ; | _E._timer.function = -(_cast_func)&_callback +(TIMER_FUNC_TYPE)_callback ; ) // Sometimes timer functions are called directly. Replace matched args. @change_timer_function_calls depends on change_timer_function_usage && (change_callback_handle_cast || change_callback_handle_cast_no_arg || change_callback_handle_arg)@ expression _E; identifier change_timer_function_usage._timer; identifier change_timer_function_usage._callback; type _cast_data; @@ _callback( ( -(_cast_data)_E +&_E->_timer | -(_cast_data)&_E +&_E._timer | -_E +&_E->_timer ) ) // If a timer has been configured without a data argument, it can be // converted without regard to the callback argument, since it is unused. @match_timer_function_unused_data@ expression _E; identifier _timer; identifier _callback; @@ ( -setup_timer(&_E->_timer, _callback, 0); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, _callback, 0L); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, _callback, 0UL); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E._timer, _callback, 0); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, _callback, 0L); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, _callback, 0UL); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_timer, _callback, 0); +timer_setup(&_timer, _callback, 0); | -setup_timer(&_timer, _callback, 0L); +timer_setup(&_timer, _callback, 0); | -setup_timer(&_timer, _callback, 0UL); +timer_setup(&_timer, _callback, 0); | -setup_timer(_timer, _callback, 0); +timer_setup(_timer, _callback, 0); | -setup_timer(_timer, _callback, 0L); +timer_setup(_timer, _callback, 0); | -setup_timer(_timer, _callback, 0UL); +timer_setup(_timer, _callback, 0); ) @change_callback_unused_data depends on match_timer_function_unused_data@ identifier match_timer_function_unused_data._callback; type _origtype; identifier _origarg; @@ void _callback( -_origtype _origarg +struct timer_list *unused ) { ... when != _origarg } Signed-off-by: Kees Cook <keescook@chromium.org>
2017-11-11net/ncsi: Improve general state loggingSamuel Mendoza-Jonas1-19/+57
The NCSI driver is mostly silent which becomes a headache when trying to determine what has occurred on the NCSI connection. This adds additional logging in a few key areas such as state transitions and calling out certain errors more visibly. Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-03net/ncsi: Make local function ncsi_get_filter() staticWei Yongjun1-1/+1
Fixes the following sparse warnings: net/ncsi/ncsi-manage.c:41:5: warning: symbol 'ncsi_get_filter' was not declared. Should it be static? Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-21net/ncsi: Enforce failover on link monitor timeoutGavin Shan1-3/+5
The NCSI channel has been configured to provide service if its link monitor timer is enabled, regardless of its state (inactive or active). So the timeout event on the link monitor indicates the out-of-service on that channel, for which a failover is needed. This sets NCSI_DEV_RESHUFFLE flag to enforce failover on link monitor timeout, regardless the channel's original state (inactive or active). Also, the link is put into "down" state to give the failing channel lowest priority when selecting for the active channel. The state of failing channel should be set to active in order for deinitialization and failover to be done. Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-21net/ncsi: Disable HWA mode when no channels are foundGavin Shan1-2/+10
When there are no NCSI channels probed, HWA (Hardware Arbitration) mode is enabled. It's not correct because HWA depends on the fact: NCSI channels exist and all of them support HWA mode. This disables HWA when no channels are probed. Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-21net/ncsi: Stop monitor if channel times out or is inactiveSamuel Mendoza-Jonas1-6/+9
ncsi_channel_monitor() misses stopping the channel monitor in several places that it should, causing a WARN_ON_ONCE() to trigger when the monitor is re-started later, eg: [ 459.040000] WARNING: CPU: 0 PID: 1093 at net/ncsi/ncsi-manage.c:269 ncsi_start_channel_monitor+0x7c/0x90 [ 459.040000] CPU: 0 PID: 1093 Comm: kworker/0:3 Not tainted 4.10.17-gaca2fdd #140 [ 459.040000] Hardware name: ASpeed SoC [ 459.040000] Workqueue: events ncsi_dev_work [ 459.040000] [<80010094>] (unwind_backtrace) from [<8000d950>] (show_stack+0x20/0x24) [ 459.040000] [<8000d950>] (show_stack) from [<801dbf70>] (dump_stack+0x20/0x28) [ 459.040000] [<801dbf70>] (dump_stack) from [<80018d7c>] (__warn+0xe0/0x108) [ 459.040000] [<80018d7c>] (__warn) from [<80018e70>] (warn_slowpath_null+0x30/0x38) [ 459.040000] [<80018e70>] (warn_slowpath_null) from [<803f6a08>] (ncsi_start_channel_monitor+0x7c/0x90) [ 459.040000] [<803f6a08>] (ncsi_start_channel_monitor) from [<803f7664>] (ncsi_configure_channel+0xdc/0x5fc) [ 459.040000] [<803f7664>] (ncsi_configure_channel) from [<803f8160>] (ncsi_dev_work+0xac/0x474) [ 459.040000] [<803f8160>] (ncsi_dev_work) from [<8002d244>] (process_one_work+0x1e0/0x450) [ 459.040000] [<8002d244>] (process_one_work) from [<8002d510>] (worker_thread+0x5c/0x570) [ 459.040000] [<8002d510>] (worker_thread) from [<80033614>] (kthread+0x124/0x164) [ 459.040000] [<80033614>] (kthread) from [<8000a5e8>] (ret_from_fork+0x14/0x2c) This also updates the monitor instead of just returning if ncsi_xmit_cmd() fails to send the get-link-status command so that the monitor properly times out. Fixes: e6f44ed6d04d3 "net/ncsi: Package and channel management" Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-11net/ncsi: Don't limit vids based on hot_channelSamuel Mendoza-Jonas1-8/+9
Currently we drop any new VLAN ids if there are more than the current (or last used) channel can support. Most importantly this is a problem if no channel has been selected yet, resulting in a segfault. Secondly this does not necessarily reflect the capabilities of any other channels. Instead only drop a new VLAN id if we are already tracking the maximum allowed by the NCSI specification. Per-channel limits are already handled by ncsi_add_filter(), but add a message to set_one_vid() to make it obvious that the channel can not support any more VLAN ids. Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-09-05net/ncsi: fix ncsi_vlan_rx_{add,kill}_vid referencesArnd Bergmann1-0/+2
We get a new link error in allmodconfig kernels after ftgmac100 started using the ncsi helpers: ERROR: "ncsi_vlan_rx_kill_vid" [drivers/net/ethernet/faraday/ftgmac100.ko] undefined! ERROR: "ncsi_vlan_rx_add_vid" [drivers/net/ethernet/faraday/ftgmac100.ko] undefined! Related to that, we get another error when CONFIG_NET_NCSI is disabled: drivers/net/ethernet/faraday/ftgmac100.c:1626:25: error: 'ncsi_vlan_rx_add_vid' undeclared here (not in a function); did you mean 'ncsi_start_dev'? drivers/net/ethernet/faraday/ftgmac100.c:1627:26: error: 'ncsi_vlan_rx_kill_vid' undeclared here (not in a function); did you mean 'ncsi_vlan_rx_add_vid'? This fixes both problems at once, using a 'static inline' stub helper for the disabled case, and exporting the functions when they are present. Fixes: 51564585d8c6 ("ftgmac100: Support NCSI VLAN filtering when available") Fixes: 21acf63013ed ("net/ncsi: Configure VLAN tag filter") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-08-28net/ncsi: Configure VLAN tag filterSamuel Mendoza-Jonas1-3/+305
Make use of the ndo_vlan_rx_{add,kill}_vid callbacks to have the NCSI stack process new VLAN tags and configure the channel VLAN filter appropriately. Several VLAN tags can be set and a "Set VLAN Filter" packet must be sent for each one, meaning the ncsi_dev_state_config_svf state must be repeated. An internal list of VLAN tags is maintained, and compared against the current channel's ncsi_channel_filter in order to keep track within the state. VLAN filters are removed in a similar manner, with the introduction of the ncsi_dev_state_config_clear_vids state. The maximum number of VLAN tag filters is determined by the "Get Capabilities" response from the channel. Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-20net/ncsi: Choose hot channel as active one if necessaryGavin Shan1-3/+19
The issue was found on BCM5718 which has two NCSI channels in one package: C0 and C1. C0 is in link-up state while C1 is in link-down state. C0 is chosen as active channel until unplugging and plugging C0's cable: On unplugging C0's cable, LSC (Link State Change) AEN packet received on C0 to report link-down event. After that, C1 is chosen as active channel. LSC AEN for link-up event is lost on C0 when plugging C0's cable back. We lose the network even C0 is usable. This resolves the issue by recording the (hot) channel that was ever chosen as active one. The hot channel is chosen to be active one if none of available channels in link-up state. With this, C0 is still the active one after unplugging C0's cable. LSC AEN packet received on C0 when plugging its cable back. Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-20net/ncsi: Fix stale link state of inactive channels on failoverGavin Shan1-1/+27
The issue was found on BCM5718 which has two NCSI channels in one package: C0 and C1. Both of them are connected to different LANs, means they are in link-up state and C0 is chosen as the active one until resetting BCM5718 happens as below. Resetting BCM5718 results in LSC (Link State Change) AEN packet received on C0, meaning LSC AEN is missed on C1. When LSC AEN packet received on C0 to report link-down, it fails over to C1 because C1 is in link-up state as software can see. However, C1 is in link-down state in hardware. It means the link state is out of synchronization between hardware and software, resulting in inappropriate channel (C1) selected as active one. This resolves the issue by sending separate GLS (Get Link Status) commands to all channels in the package before trying to do failover. The last link states of all channels in the package are retrieved. With it, C0 (not C1) is selected as active one as expected. Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-20net/ncsi: Avoid if statements in ncsi_suspend_channel()Gavin Shan1-28/+50
There are several if/else statements in the state machine implemented by switch/case in ncsi_suspend_channel() to avoid duplicated code. It makes the code a bit hard to be understood. This drops if/else statements in ncsi_suspend_channel() to improve the code readability as Joel Stanley suggested. Also, it becomes easy to add more states in the state machine without affecting current code. No logical changes introduced by this. Suggested-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-04net/ncsi: Introduce ncsi_stop_dev()Gavin Shan1-13/+24
This introduces ncsi_stop_dev(), as counterpart to ncsi_start_dev(), to stop the NCSI device so that it can be reenabled in future. This API should be called when the network device driver is going to shutdown the device. There are 3 things done in the function: Stop the channel monitoring; Reset channels to inactive state; Report NCSI link down. Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-04net/ncsi: Rework the channel monitoringGavin Shan1-19/+25
The original NCSI channel monitoring was implemented based on a backoff algorithm: the GLS response should be received in the specified interval. Otherwise, the channel is regarded as dead and failover should be taken if current channel is an active one. There are several problems in the implementation: (A) On BCM5718, we found when the IID (Instance ID) in the GLS command packet changes from 255 to 1, the response corresponding to IID#1 never comes in. It means we cannot make the unfair judgement that the channel is dead when one response is missed. (B) The code's readability should be improved. (C) We should do failover when current channel is active one and the channel monitoring should be marked as disabled before doing failover. This reworks the channel monitoring to address all above issues. The fields for channel monitoring is put into separate struct and the state of channel monitoring is predefined. The channel is regarded alive if the network controller responses to one of two GLS commands or both of them in 5 seconds. Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-04net/ncsi: Allow to extend NCSI request propertiesGavin Shan1-9/+10
There is only one NCSI request property for now: the response for the sent command need drive the workqueue or not. So we had one field (@driven) for the purpose. We lost the flexibility to extend NCSI request properties. This replaces @driven with @flags and @req_flags in NCSI request and NCSI command argument struct. Each bit of the newly introduced field can be used for one property. No functional changes introduced. Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-04net/ncsi: Rework request index allocationGavin Shan1-8/+9
The NCSI request index (struct ncsi_request::id) is put into instance ID (IID) field while sending NCSI command packet. It was designed the available IDs are given in round-robin fashion. @ndp->request_id was introduced to represent the next available ID, but it has been used as number of successively allocated IDs. It breaks the round-robin design. Besides, we shouldn't put 0 to NCSI command packet's IID field, meaning ID#0 should be reserved according section 6.3.1.1 in NCSI spec (v1.1.0). This fixes above two issues. With it applied, the available IDs will be assigned in round-robin fashion and ID#0 won't be assigned. Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-04net/ncsi: Don't probe on the reserved channel ID (0x1f)Gavin Shan1-2/+2
We needn't send CIS (Clear Initial State) command to the NCSI reserved channel (0x1f) in the enumeration. We shouldn't receive a valid response from CIS on NCSI channel 0x1f. Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-04net/ncsi: Introduce NCSI_RESERVED_CHANNELGavin Shan1-7/+7
This defines NCSI_RESERVED_CHANNEL as the reserved NCSI channel ID (0x1f). No logical changes introduced. Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-04net/ncsi: Avoid unused-value build warning from ia64-linux-gccGavin Shan1-17/+54
xchg() is used to set NCSI channel's state in order for consistent access to the state. xchg()'s return value should be used. Otherwise, one build warning will be raised (with -Wunused-value) as below message indicates. It is reported by ia64-linux-gcc (GCC) 4.9.0. net/ncsi/ncsi-manage.c: In function 'ncsi_channel_monitor': arch/ia64/include/uapi/asm/cmpxchg.h:56:2: warning: value computed is \ not used [-Wunused-value] ((__typeof__(*(ptr))) __xchg((unsigned long) (x), (ptr), sizeof(*(ptr)))) ^ net/ncsi/ncsi-manage.c:202:3: note: in expansion of macro 'xchg' xchg(&nc->state, NCSI_CHANNEL_INACTIVE); This removes the atomic access to NCSI channel's state avoid the above build warning. We have to hold the channel's lock when its state is readed or updated. No functional changes introduced. Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-25net/ncsi: avoid maybe-uninitialized warningArnd Bergmann1-13/+19
gcc-4.9 and higher warn about the newly added NSCI code: net/ncsi/ncsi-manage.c: In function 'ncsi_process_next_channel': net/ncsi/ncsi-manage.c:1003:2: error: 'old_state' may be used uninitialized in this function [-Werror=maybe-uninitialized] The warning is a false positive and therefore harmless, but it would be good to avoid it anyway. I have determined that the barrier in the spin_unlock_irqsave() is what confuses gcc to the point that it cannot track whether the variable was unused or not. This rearranges the code in a way that makes it obvious to gcc that old_state is always initialized at the time of use, functionally this should not change anything. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-19net/ncsi: Package and channel managementGavin Shan1-0/+763
This manages NCSI packages and channels: * The available packages and channels are enumerated in the first time of calling ncsi_start_dev(). The channels' capabilities are probed in the meanwhile. The NCSI network topology won't change until the NCSI device is destroyed. * There in a queue in every NCSI device. The element in the queue, channel, is waiting for configuration (bringup) or suspending (teardown). The channel's state (inactive/active) indicates the futher action (configuration or suspending) will be applied on the channel. Another channel's state (invisible) means the requested action is being applied. * The hardware arbitration will be enabled if all available packages and channels support it. All available channels try to provide service when hardware arbitration is enabled. Otherwise, one channel is selected as the active one at once. * When channel is in active state, meaning it's providing service, a timer started to retrieve the channe's link status. If the channel's link status fails to be updated in the determined period, the channel is going to be reconfigured. It's the error handling implementation as defined in NCSI spec. Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Acked-by: Joel Stanley <joel@jms.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-19net/ncsi: Resource managementGavin Shan1-0/+436
NCSI spec (DSP0222) defines several objects: package, channel, mode, filter, version and statistics etc. This introduces the data structs to represent those objects and implement functions to manage them. Also, this introduces CONFIG_NET_NCSI for the newly implemented NCSI stack. * The user (e.g. netdev driver) dereference NCSI device by "struct ncsi_dev", which is embedded to "struct ncsi_dev_priv". The later one is used by NCSI stack internally. * Every NCSI device can have multiple packages simultaneously, up to 8 packages. It's represented by "struct ncsi_package" and identified by 3-bits ID. * Every NCSI package can have multiple channels, up to 32. It's represented by "struct ncsi_channel" and identified by 5-bits ID. * Every NCSI channel has version, statistics, various modes and filters. They are represented by "struct ncsi_channel_version", "struct ncsi_channel_stats", "struct ncsi_channel_mode" and "struct ncsi_channel_filter" separately. * Apart from AEN (Asynchronous Event Notification), the NCSI stack works in terms of command and response. This introduces "struct ncsi_req" to represent a complete NCSI transaction made of NCSI request and response. link: https://www.dmtf.org/sites/default/files/standards/documents/DSP0222_1.1.0.pdf Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Acked-by: Joel Stanley <joel@jms.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-10 13:36:19 +0000