summaryrefslogtreecommitdiffstats
path: root/net/mac80211
AgeCommit message (Collapse)AuthorFilesLines
2017-11-20mac80211: properly free requested-but-not-started TX agg sessionsJohannes Berg1-0/+5
When deleting a station or otherwise tearing down all aggregation sessions, make sure to delete requested but not yet started ones, to avoid the following scenario: * session is requested, added to tid_start_tx[] * ieee80211_ba_session_work() runs, gets past BLOCK_BA check * ieee80211_sta_tear_down_BA_sessions() runs, locks &sta->ampdu_mlme.mtx, e.g. while deleting the station - deleting all active sessions * ieee80211_ba_session_work() continues since tear down flushes it, and calls ieee80211_tx_ba_session_handle_start() for the new session, arms the timer for it * station deletion continues to __cleanup_single_sta() and frees the session struct, while the timer is armed Reported-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-11-20mac80211: aggregation: Convert timers to use timer_setup()Kees Cook4-60/+45
In preparation for unconditionally passing the struct timer_list pointer to all timer callbacks, switch to using the new timer_setup() and from_timer() to pass the timer pointer explicitly. This removes the tid mapping array and expands the tid structures to add a pointer back to the station, along with the tid index itself. Cc: Johannes Berg <johannes@sipsolutions.net> Cc: "David S. Miller" <davem@davemloft.net> Cc: linux-wireless@vger.kernel.org Cc: netdev@vger.kernel.org Signed-off-by: Kees Cook <keescook@chromium.org> [switch tid variables to u8, the valid range is 0-15 at most, initialize tid_tx->sta/tid properly] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-11-20mac80211: Convert timers to use timer_setup()Kees Cook11-59/+50
In preparation for unconditionally passing the struct timer_list pointer to all timer callbacks, switch to using the new timer_setup() and from_timer() to pass the timer pointer explicitly. Cc: Johannes Berg <johannes@sipsolutions.net> Cc: "David S. Miller" <davem@davemloft.net> Cc: linux-wireless@vger.kernel.org Cc: netdev@vger.kernel.org Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-11-15Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-nextLinus Torvalds22-269/+270
Pull networking updates from David Miller: "Highlights: 1) Maintain the TCP retransmit queue using an rbtree, with 1GB windows at 100Gb this really has become necessary. From Eric Dumazet. 2) Multi-program support for cgroup+bpf, from Alexei Starovoitov. 3) Perform broadcast flooding in hardware in mv88e6xxx, from Andrew Lunn. 4) Add meter action support to openvswitch, from Andy Zhou. 5) Add a data meta pointer for BPF accessible packets, from Daniel Borkmann. 6) Namespace-ify almost all TCP sysctl knobs, from Eric Dumazet. 7) Turn on Broadcom Tags in b53 driver, from Florian Fainelli. 8) More work to move the RTNL mutex down, from Florian Westphal. 9) Add 'bpftool' utility, to help with bpf program introspection. From Jakub Kicinski. 10) Add new 'cpumap' type for XDP_REDIRECT action, from Jesper Dangaard Brouer. 11) Support 'blocks' of transformations in the packet scheduler which can span multiple network devices, from Jiri Pirko. 12) TC flower offload support in cxgb4, from Kumar Sanghvi. 13) Priority based stream scheduler for SCTP, from Marcelo Ricardo Leitner. 14) Thunderbolt networking driver, from Amir Levy and Mika Westerberg. 15) Add RED qdisc offloadability, and use it in mlxsw driver. From Nogah Frankel. 16) eBPF based device controller for cgroup v2, from Roman Gushchin. 17) Add some fundamental tracepoints for TCP, from Song Liu. 18) Remove garbage collection from ipv6 route layer, this is a significant accomplishment. From Wei Wang. 19) Add multicast route offload support to mlxsw, from Yotam Gigi" * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2177 commits) tcp: highest_sack fix geneve: fix fill_info when link down bpf: fix lockdep splat net: cdc_ncm: GetNtbFormat endian fix openvswitch: meter: fix NULL pointer dereference in ovs_meter_cmd_reply_start netem: remove unnecessary 64 bit modulus netem: use 64 bit divide by rate tcp: Namespace-ify sysctl_tcp_default_congestion_control net: Protect iterations over net::fib_notifier_ops in fib_seq_sum() ipv6: set all.accept_dad to 0 by default uapi: fix linux/tls.h userspace compilation error usbnet: ipheth: prevent TX queue timeouts when device not ready vhost_net: conditionally enable tx polling uapi: fix linux/rxrpc.h userspace compilation errors net: stmmac: fix LPI transitioning for dwmac4 atm: horizon: Fix irq release error net-sysfs: trigger netlink notification on ifalias change via sysfs openvswitch: Using kfree_rcu() to simplify the code openvswitch: Make local function ovs_nsh_key_attr_size() static openvswitch: Fix return value check in ovs_meter_cmd_features() ...
2017-11-07Merge branch 'linus' into locking/core, to resolve conflictsIngo Molnar13-8/+52
Conflicts: include/linux/compiler-clang.h include/linux/compiler-gcc.h include/linux/compiler-intel.h include/uapi/linux/stddef.h Signed-off-by: Ingo Molnar <mingo@kernel.org>
2017-11-04Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller11-0/+11
Files removed in 'net-next' had their license header updated in 'net'. We take the remove from 'net-next'. Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-02Merge tag 'spdx_identifiers-4.14-rc8' of ↵Linus Torvalds11-0/+11
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core Pull initial SPDX identifiers from Greg KH: "License cleanup: add SPDX license identifiers to some files Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>" * tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: License cleanup: add SPDX license identifier to uapi header files with a license License cleanup: add SPDX license identifier to uapi header files with no license License cleanup: add SPDX GPL-2.0 license identifier to files with no license
2017-11-02License cleanup: add SPDX GPL-2.0 license identifier to files with no licenseGreg Kroah-Hartman11-0/+11
Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-30Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2-8/+41
Several conflicts here. NFP driver bug fix adding nfp_netdev_is_nfp_repr() check to nfp_fl_output() needed some adjustments because the code block is in an else block now. Parallel additions to net/pkt_cls.h and net/sch_generic.h A bug fix in __tcp_retransmit_skb() conflicted with some of the rbtree changes in net-next. The tc action RCU callback fixes in 'net' had some overlap with some of the recent tcf_block reworking. Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-25mac80211: don't compare TKIP TX MIC key in reinstall preventionJohannes Berg1-2/+34
For the reinstall prevention, the code I had added compares the whole key. It turns out though that iwlwifi firmware doesn't provide the TKIP TX MIC key as it's not needed in client mode, and thus the comparison will always return false. For client mode, thus always zero out the TX MIC key part before doing the comparison in order to avoid accepting the reinstall of the key with identical encryption and RX MIC key, but not the same TX MIC key (since the supplicant provides the real one.) Fixes: fdf7cb4185b6 ("mac80211: accept key reinstall without changing anything") Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-10-25locking/atomics: COCCINELLE/treewide: Convert trivial ACCESS_ONCE() patterns ↵Mark Rutland1-1/+1
to READ_ONCE()/WRITE_ONCE() Please do not apply this to mainline directly, instead please re-run the coccinelle script shown below and apply its output. For several reasons, it is desirable to use {READ,WRITE}_ONCE() in preference to ACCESS_ONCE(), and new code is expected to use one of the former. So far, there's been no reason to change most existing uses of ACCESS_ONCE(), as these aren't harmful, and changing them results in churn. However, for some features, the read/write distinction is critical to correct operation. To distinguish these cases, separate read/write accessors must be used. This patch migrates (most) remaining ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following coccinelle script: ---- // Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and // WRITE_ONCE() // $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch virtual patch @ depends on patch @ expression E1, E2; @@ - ACCESS_ONCE(E1) = E2 + WRITE_ONCE(E1, E2) @ depends on patch @ expression E; @@ - ACCESS_ONCE(E) + READ_ONCE(E) ---- Signed-off-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: davem@davemloft.net Cc: linux-arch@vger.kernel.org Cc: mpe@ellerman.id.au Cc: shuah@kernel.org Cc: snitzer@redhat.com Cc: thor.thayer@linux.intel.com Cc: tj@kernel.org Cc: viro@zeniv.linux.org.uk Cc: will.deacon@arm.com Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
2017-10-22Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller1-4/+17
There were quite a few overlapping sets of changes here. Daniel's bug fix for off-by-ones in the new BPF branch instructions, along with the added allowances for "data_end > ptr + x" forms collided with the metadata additions. Along with those three changes came veritifer test cases, which in their final form I tried to group together properly. If I had just trimmed GIT's conflict tags as-is, this would have split up the meta tests unnecessarily. In the socketmap code, a set of preemption disabling changes overlapped with the rename of bpf_compute_data_end() to bpf_compute_data_pointers(). Changes were made to the mv88e6060.c driver set addr method which got removed in net-next. The hyperv transport socket layer had a locking change in 'net' which overlapped with a change of socket state macro usage in 'net-next'. Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-18mac80211: validate user rate mask before configuring driverJohannes Berg1-6/+6
Ben reported that when the user rate mask is rejected for not matching any basic rate, the driver had already been configured. This is clearly an oversight in my original change, fix this by doing the validation before calling the driver. Reported-by: Ben Greear <greearb@candelatech.com> Fixes: e8e4f5280ddd ("mac80211: reject/clear user rate mask if not usable") Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-10-18mac80211: use constant time comparison with keysJason A. Donenfeld1-1/+2
Otherwise we risk leaking information via timing side channel. Fixes: fdf7cb4185b6 ("mac80211: accept key reinstall without changing anything") Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-10-16mac80211: accept key reinstall without changing anythingJohannes Berg1-4/+17
When a key is reinstalled we can reset the replay counters etc. which can lead to nonce reuse and/or replay detection being impossible, breaking security properties, as described in the "KRACK attacks". In particular, CVE-2017-13080 applies to GTK rekeying that happened in firmware while the host is in D3, with the second part of the attack being done after the host wakes up. In this case, the wpa_supplicant mitigation isn't sufficient since wpa_supplicant doesn't know the GTK material. In case this happens, simply silently accept the new key coming from userspace but don't take any action on it since it's the same key; this keeps the PN replay counters intact. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-10-13mac80211: don't track HT capability changesJohannes Berg1-11/+3
The code here (more or less accidentally) tracks the HT capability of the AP when connected, and we found at least one AP that erroneously toggles its 20/40 capability bit when changing between 20/40 MHz. The connection to the AP is then broken because we set the 40 MHz disable flag based on this, as soon as it switches to 20 MHz, but because the flag then changed, we disconnect. I'd be inclined to just ignore this issue, since we then reconnect while the AP is in 20 MHz mode and never use 40 MHz with it again, but this code is a bit strange anyway - we don't use the capabilities for anything else. Change the code to simply not track the HT capabilities at all, which assumes that the AP at least sets 20/40 capability when operating in 40 MHz (or higher). If not, rate scaling might end up using only the narrower bandwidth. The new behaviour also mirrors what VHT does, where we only check the VHT operation. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-10-11mac80211: use crypto_aead_authsize()Johannes Berg1-2/+2
Evidently this API is intended to be used to isolate against API changes, so use it instead of accessing ->authsize. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-10-11mac80211: only remove AP VLAN frames from TXQJohannes Berg3-22/+39
When removing an AP VLAN interface, mac80211 currently purges the entire TXQ for the AP interface. Fix this by using the FQ API introduced in the previous patch to filter frames. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-10-11mac80211: aead api to reduce redundancyXiang Gao7-152/+111
Currently, the aes_ccm.c and aes_gcm.c are almost line by line copy of each other. This patch reduce code redundancy by moving the code in these two files to crypto/aead_api.c to make it a higher level aead api. The file aes_ccm.c and aes_gcm.c are removed and all the functions there are now implemented in their headers using the newly added aead api. Signed-off-by: Xiang Gao <qasdfgtyuiop@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-10-06net/mac80211/mesh_plink: Convert timers to use timer_setup()Kees Cook4-7/+10
In preparation for unconditionally passing the struct timer_list pointer to all timer callbacks, switch to using the new timer_setup() and from_timer() to pass the timer pointer explicitly. This requires adding a pointer back to the sta_info since container_of() can't resolve the sta_info. Cc: Johannes Berg <johannes@sipsolutions.net> Cc: "David S. Miller" <davem@davemloft.net> Cc: linux-wireless@vger.kernel.org Cc: netdev@vger.kernel.org Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-10-02mac80211: fix STA_SLOW_THRESHOLD htmldocs failureStanislaw Gruszka1-1/+1
Patch fixes htmldocs build problem: Error(.//net/mac80211/sta_info.h:416): cannot understand prototype: 'STA_SLOW_THRESHOLD 6000 ' Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-10-02mac80211: fix bandwidth computation for TDLS peersManikanta Pubbisetty1-0/+10
Section 11.23.1 of 80211-2016 specification allows TDLS peers to operate on wider bandwidths though they are connected to a BSS which do not support wider bandwidth operations, provided both the peers advertise wider bandwidth capabilities. The existing logic considers the minimum of station's and AP's capability for bandwidth computation. The same logic applies for TDLS peers as well, this restricts operating on wider bandwidths over a TDLS link when the peers are connected to legacy APs. As an example, if 80Mhz VHT capable peers are connected to a 20Mhz 5 GHz AP, then as per the existing logic TDLS operation will be restricted to 20Mhz. Address this problem by not considering BSS capability in bandwidth computation if the participating TDLS peers have wider bandwidth capability. Signed-off-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com> [lots of wording/typo fixes] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-09-21mac80211: recalculate some sta parameters after insertionGregory Greenman1-25/+32
Sometimes a station is added already in ASSOC state. For example, in AP mode, when a client station didn't get assoc resp and sends an assoc req again. If a station is inserted when its state is ASSOC or higher, the min chandef and allow_p2p_go_ps should be recalculated again after the insertion. Before this patch the recalculation happened only in sta_info_move_state which occurs before the insertion of the sta and thus even though it calls ieee80211_recalc_min_chandef/_p2p_go_ps_allowed functions, since sdata->local->sta_list is still empty at this point, it doesn't do anything. Signed-off-by: Gregory Greenman <gregory.greenman@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-09-21mac80211: use offsetofend()Johannes Berg4-10/+8
This was created using the following spatch: @find@ type S; expression M, M2; position p; @@ offsetof(S, M) + sizeof(M2)@p @script:python@ m << find.M; m2 << find.M2; @@ if not m2.endswith('-> ' + m): cocci.include_match(False) @change@ type find.S; expression find.M, find.M2; position find.p; @@ -offsetof(S, M) + sizeof(M2)@p +offsetofend(S, M) Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-09-21mac80211: Simplify locking in ieee80211_sta_tear_down_BA_sessions()Ilan peer1-5/+7
Simplify the locking in ieee80211_sta_tear_down_BA_sessions() and lock sta->ampdu_mlme.mtx over the entire function instead of locking/unlocking it for each TID etc. Signed-off-by: Ilan Peer <ilan.peer@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-09-21mac80211: add documentation to ieee80211_rx_ba_offl()Luca Coelho1-2/+2
Add documentation to ieee80211_rx_ba_offl() function and, while at it, rename the bit argument to tid, for consistency. Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-09-21mac80211: oce: enable receiving of bcast probe respRoee Zamir1-9/+28
One of OCE's optimizations is acception of broadcast probe responses. Accept broadcast probe responses but don't set NL80211_EXT_FEATURE_ACCEPT_BCAST_PROBE_RESP. Because a device's firmware may filter out the broadcast probe resp - drivers should set this flag. Signed-off-by: Roee Zamir <roee.zamir@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> [johannes: make accepting broadcast conditional on the nl80211 scan flag that was added for that specific purpose] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-09-21mac80211: simplify and clarify IE splittingJohannes Berg2-24/+16
There's no need to split off IEs from the ones obtained from userspace, if they were already split off, so for example IEs that went before HT don't have to be listed again to go before VHT. Simplify the code here so it's clearer. While at it, also clarify the comments regarding the DMG (60 GHz) elements. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-09-21mac80211: avoid allocating TXQs that won't be usedJohannes Berg1-1/+3
For AP_VLAN and monitor interfaces we'll never use the TXQs we allocated, so avoid doing so. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-09-06mac80211: fix deadlock in driver-managed RX BA session startJohannes Berg3-14/+28
When an RX BA session is started by the driver, and it has to tell mac80211 about it, the corresponding bit in tid_rx_manage_offl gets set and the BA session work is scheduled. Upon testing this bit, it will call __ieee80211_start_rx_ba_session(), thus deadlocking as it already holds the ampdu_mlme.mtx, which that acquires again. Fix this by adding ___ieee80211_start_rx_ba_session(), a version of the function that requires the mutex already held. Cc: stable@vger.kernel.org Fixes: 699cb58c8a52 ("mac80211: manage RX BA session offload without SKB queue") Reported-by: Matteo Croce <mcroce@redhat.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-09-06mac80211: Complete ampdu work schedule during session tear downIlan peer1-0/+18
Commit 7a7c0a6438b8 ("mac80211: fix TX aggregation start/stop callback race") added a cancellation of the ampdu work after the loop that stopped the Tx and Rx BA sessions. However, in some cases, e.g., during HW reconfig, the low level driver might call mac80211 APIs to complete the stopping of the BA sessions, which would queue the ampdu work to handle the actual completion. This work needs to be performed as otherwise mac80211 data structures would not be properly synced. Fix this by checking if BA session STOP_CB bit is set after the BA session cancellation and properly clean the session. Signed-off-by: Ilan Peer <ilan.peer@intel.com> [Johannes: the work isn't flushed because that could do other things we don't want, and the locking situation isn't clear] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-09-05mac80211: flush hw_roc_start work before cancelling the ROCAvraham Stern1-0/+2
When HW ROC is supported it is possible that after the HW notified that the ROC has started, the ROC was cancelled and another ROC was added while the hw_roc_start worker is waiting on the mutex (since cancelling the ROC and adding another one also holds the same mutex). As a result, the hw_roc_start worker will continue to run after the new ROC is added but before it is actually started by the HW. This may result in notifying userspace that the ROC has started before it actually does, or in case of management tx ROC, in an attempt to tx while not on the right channel. In addition, when the driver will notify mac80211 that the second ROC has started, mac80211 will warn that this ROC has already been notified. Fix this by flushing the hw_roc_start work before cancelling an ROC. Cc: stable@vger.kernel.org Signed-off-by: Avraham Stern <avraham.stern@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-09-05mac80211: agg-tx: call drv_wake_tx_queue in proper contextJohannes Berg1-0/+4
Since drv_wake_tx_queue() is normally called in the TX path, which is already in an RCU critical section, we should call it the same way in the aggregation code path, so if the driver expects to be able to use RCU, it'll already be protected without having to enter a nested critical section. Additionally, disable soft-IRQs, since not doing so could cause issues in a driver that relies on them already being disabled like in the other path. Fixes: ba8c3d6f16a1 ("mac80211: add an intermediate software queue implementation") Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-09-05mac80211: Fix null pointer dereference with iTXQ supportChunho Lee1-1/+2
This change adds null pointer check before dereferencing pointer dev on netif_tx_start_all_queues() when an interface is added. With iTXQ support, netif_tx_start_all_queues() is always called while an interface is added. however, the netdev queues are not associated and dev is null when the interface is either NL80211_IFTYPE_P2P_DEVICE or NL80211_IFTYPE_NAN. Signed-off-by: Chunho Lee <ch.lee@newracom.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-09-05mac80211: add MESH IE in the correct orderLiad Kaufman1-1/+1
VHT MESH support was added, but the order of the IEs wasn't enforced. Fix that. Signed-off-by: Liad Kaufman <liad.kaufman@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-09-05mac80211: shorten debug prints using ht_dbg() to avoid warningSharon Dvir1-2/+2
Invoking ht_dbg() with too long of a string will print a warning. Shorten the messages while retaining the printed patameters. Signed-off-by: Sharon Dvir <sharon.dvir@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-09-05mac80211: fix VLAN handling with TXQsJohannes Berg2-9/+44
With TXQs, the AP_VLAN interfaces are resolved to their owner AP interface when enqueuing the frame, which makes sense since the frame really goes out on that as far as the driver is concerned. However, this introduces a problem: frames to be encrypted with a VLAN-specific GTK will now be encrypted with the AP GTK, since the information about which virtual interface to use to select the key is taken from the TXQ. Fix this by preserving info->control.vif and using that in the dequeue function. This now requires doing the driver-mapping in the dequeue as well. Since there's no way to filter the frames that are sitting on a TXQ, drop all frames, which may affect other interfaces, when an AP_VLAN is removed. Cc: stable@vger.kernel.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-09-05mac80211: fix incorrect assignment of reassoc valueSimon Dinkin1-1/+1
this fix minor issue in the log message. in ieee80211_rx_mgmt_assoc_resp function, when assigning the reassoc value from the mgmt frame control: ieee80211_is_reassoc_resp function need to be used, instead of ieee80211_is_reassoc_req function. Signed-off-by: Simon Dinkin <simon.dinkin@tandemg.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-08-09mac80211: add api to start ba session timer expired flowNaftali Goldstein1-1/+21
Some drivers handle rx buffer reordering internally (and by extension handle also the rx ba session timer internally), but do not ofload the addba/delba negotiation. Add an api for these drivers to properly tear-down the ba session, including sending a delba. Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2017-06-20net: manual clean code which call skb_put_[data:zero]yuan linyu2-18/+13
Signed-off-by: yuan linyu <Linyu.Yuan@alcatel-sbell.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-16networking: make skb_push & __skb_push return void pointersJohannes Berg3-4/+4
It seems like a historic accident that these return unsigned char *, and in many places that means casts are required, more often than not. Make these functions return void * and remove all the casts across the tree, adding a (u8 *) cast only where the unsigned char pointer was used directly, all done with the following spatch: @@ expression SKB, LEN; typedef u8; identifier fn = { skb_push, __skb_push, skb_push_rcsum }; @@ - *(fn(SKB, LEN)) + *(u8 *)fn(SKB, LEN) @@ expression E, SKB, LEN; identifier fn = { skb_push, __skb_push, skb_push_rcsum }; type T; @@ - E = ((T *)(fn(SKB, LEN))) + E = fn(SKB, LEN) @@ expression SKB, LEN; identifier fn = { skb_push, __skb_push, skb_push_rcsum }; @@ - fn(SKB, LEN)[0] + *(u8 *)fn(SKB, LEN) Note that the last part there converts from push(...)[0] to the more idiomatic *(u8 *)push(...). Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-16networking: make skb_put & friends return void pointersJohannes Berg8-15/+15
It seems like a historic accident that these return unsigned char *, and in many places that means casts are required, more often than not. Make these functions (skb_put, __skb_put and pskb_put) return void * and remove all the casts across the tree, adding a (u8 *) cast only where the unsigned char pointer was used directly, all done with the following spatch: @@ expression SKB, LEN; typedef u8; identifier fn = { skb_put, __skb_put }; @@ - *(fn(SKB, LEN)) + *(u8 *)fn(SKB, LEN) @@ expression E, SKB, LEN; identifier fn = { skb_put, __skb_put }; type T; @@ - E = ((T *)(fn(SKB, LEN))) + E = fn(SKB, LEN) which actually doesn't cover pskb_put since there are only three users overall. A handful of stragglers were converted manually, notably a macro in drivers/isdn/i4l/isdn_bsdcomp.c and, oddly enough, one of the many instances in net/bluetooth/hci_sock.c. In the former file, I also had to fix one whitespace problem spatch introduced. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-16networking: introduce and use skb_put_data()Johannes Berg8-53/+37
A common pattern with skb_put() is to just want to memcpy() some data into the new space, introduce skb_put_data() for this. An spatch similar to the one for skb_put_zero() converts many of the places using it: @@ identifier p, p2; expression len, skb, data; type t, t2; @@ ( -p = skb_put(skb, len); +p = skb_put_data(skb, data, len); | -p = (t)skb_put(skb, len); +p = skb_put_data(skb, data, len); ) ( p2 = (t2)p; -memcpy(p2, data, len); | -memcpy(p, data, len); ) @@ type t, t2; identifier p, p2; expression skb, data; @@ t *p; ... ( -p = skb_put(skb, sizeof(t)); +p = skb_put_data(skb, data, sizeof(t)); | -p = (t *)skb_put(skb, sizeof(t)); +p = skb_put_data(skb, data, sizeof(t)); ) ( p2 = (t2)p; -memcpy(p2, data, sizeof(*p)); | -memcpy(p, data, sizeof(*p)); ) @@ expression skb, len, data; @@ -memcpy(skb_put(skb, len), data, len); +skb_put_data(skb, data, len); (again, manually post-processed to retain some comments) Reviewed-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-16networking: convert many more places to skb_put_zero()Johannes Berg14-44/+23
There were many places that my previous spatch didn't find, as pointed out by yuan linyu in various patches. The following spatch found many more and also removes the now unnecessary casts: @@ identifier p, p2; expression len; expression skb; type t, t2; @@ ( -p = skb_put(skb, len); +p = skb_put_zero(skb, len); | -p = (t)skb_put(skb, len); +p = skb_put_zero(skb, len); ) ... when != p ( p2 = (t2)p; -memset(p2, 0, len); | -memset(p, 0, len); ) @@ type t, t2; identifier p, p2; expression skb; @@ t *p; ... ( -p = skb_put(skb, sizeof(t)); +p = skb_put_zero(skb, sizeof(t)); | -p = (t *)skb_put(skb, sizeof(t)); +p = skb_put_zero(skb, sizeof(t)); ) ... when != p ( p2 = (t2)p; -memset(p2, 0, sizeof(*p)); | -memset(p, 0, sizeof(*p)); ) @@ expression skb, len; @@ -memset(skb_put(skb, len), 0, len); +skb_put_zero(skb, len); Apply it to the tree (with one manual fixup to keep the comment in vxlan.c, which spatch removed.) Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-15Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller6-40/+48
The conflicts were two cases of overlapping changes in batman-adv and the qed driver. Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-13Merge tag 'mac80211-for-davem-2017-06-13' of ↵David S. Miller5-37/+44
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211 Johannes Berg says: ==================== Some fixes: * Avi fixes some fallout from my mac80211 RX flags changes * Emmanuel fixes an issue with adhering to the spec, and an oversight in the SMPS management code * Jason's patch makes mac80211 use constant-time memory comparisons for message authentication, to avoid having potentially observable timing differences * my fix makes mac80211 set the basic rates bitmap before the channel so the next update to the driver has more consistent data - this required another rework patch to remove some useless 5/10 MHz code that can never be hit ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-13mac80211: add the action to the drv_ampdu_action tracepointEmmanuel Grumbach1-4/+7
It is very useful to know what ampdu action is currently happening. Add this information to the tracepoint. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-06-13mac80211: don't send SMPS action frame in AP mode when not neededEmmanuel Grumbach1-0/+2
mac80211 allows to modify the SMPS state of an AP both, when it is started, and after it has been started. Such a change will trigger an action frame to all the peers that are currently connected, and will be remembered so that new peers will get notified as soon as they connect (since the SMPS setting in the beacon may not be the right one). This means that we need to remember the SMPS state currently requested as well as the SMPS state that was configured initially (and advertised in the beacon). The former is bss->req_smps and the latter is sdata->smps_mode. Initially, the AP interface could only be started with SMPS_OFF, which means that sdata->smps_mode was SMPS_OFF always. Later, a nl80211 API was added to be able to start an AP with a different AP mode. That code forgot to update bss->req_smps and because of that, if the AP interface was started with SMPS_DYNAMIC, we had: sdata->smps_mode = SMPS_DYNAMIC bss->req_smps = SMPS_OFF That configuration made mac80211 think it needs to fire off an action frame to any new station connecting to the AP in order to let it know that the actual SMPS configuration is SMPS_OFF. Fix that by properly setting bss->req_smps in ieee80211_start_ap. Fixes: f69931748730 ("mac80211: set smps_mode according to ap params") Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-06-13mac80211/wpa: use constant time memory comparison for MACsJason A. Donenfeld1-4/+5
Otherwise, we enable all sorts of forgeries via timing attack. Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: linux-wireless@vger.kernel.org Cc: stable@vger.kernel.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-06-13mac80211: set bss_info data before configuring the channelJohannes Berg1-10/+28
When mac80211 changes the channel, it also calls into the driver's bss_info_changed() callback, e.g. with BSS_CHANGED_IDLE. The driver may, like iwlwifi does, access more data from bss_info in that case and iwlwifi accesses the basic_rates bitmap, but if changing from a band with more (basic) rates to one with fewer, an out-of-bounds access of the rate array may result. While we can't avoid having invalid data at some point in time, we can avoid having it while we call the driver - so set up all the data before configuring the channel, and then apply it afterwards. This fixes https://bugzilla.kernel.org/show_bug.cgi?id=195677 Reported-by: Johannes Hirte <johannes.hirte@datenkhaos.de> Tested-by: Johannes Hirte <johannes.hirte@datenkhaos.de> Debugged-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>