summaryrefslogtreecommitdiffstats
path: root/net/mac80211/scan.c
AgeCommit message (Collapse)AuthorFilesLines
2020-09-28mac80211: convert S1G beacon to scan resultsThomas Pedersen1-4/+13
This commit finds the correct offset for Information Elements in S1G beacon frames so they can be reported in scan results. Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com> Link: https://lore.kernel.org/r/20200922022818.15855-8-thomas@adapt-ip.com Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-09-28mac80211: s1g: choose scanning width based on frequencyThomas Pedersen1-0/+17
An S1G BSS can beacon at either 1 or 2 MHz and the channel width is unique to a given frequency. Ignore scan channel width for now and use the allowed channel width. Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com> Link: https://lore.kernel.org/r/20200922022818.15855-3-thomas@adapt-ip.com Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-09-28nl80211/cfg80211: support 6 GHz scanningTova Mussai1-2/+7
Support 6 GHz scanning, by * a new scan flag to scan for colocated BSSes advertised by (and found) APs on 2.4 & 5 GHz * doing the necessary reduced neighbor report parsing for this, to find them * adding the ability to split the scan request in case the device by itself cannot support this. Also add some necessary bits in mac80211 to not break with these changes. Signed-off-by: Tova Mussai <tova.mussai@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Link: https://lore.kernel.org/r/20200918113313.232917c93af9.Ida22f0212f9122f47094d81659e879a50434a6a2@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-07-31mac80211: remove unused flags argument in transmit functionsMathy Vanhoef1-1/+1
The flags argument in transmit functions is no longer being used and can be removed. Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be> Link: https://lore.kernel.org/r/20200723100153.31631-5-Mathy.Vanhoef@kuleuven.be Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-07-31mac80211: use same flag everywhere to avoid sequence number overwriteMathy Vanhoef1-4/+3
Use the IEEE80211_TX_CTRL_NO_SEQNO flag in ieee80211_tx_info to mark probe requests whose sequence number must not be overwritten. This provides consistency with the radiotap flag that can be set to indicate that the sequence number of an injected frame should not be overwritten. Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be> Link: https://lore.kernel.org/r/20200723100153.31631-4-Mathy.Vanhoef@kuleuven.be Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-07-31nl80211: S1G band and channel definitionsThomas Pedersen1-0/+1
Gives drivers the definitions needed to advertise support for S1G bands. Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com> Link: https://lore.kernel.org/r/20200602062247.23212-1-thomas@adapt-ip.com Link: https://lore.kernel.org/r/20200731055636.795173-1-thomas@adapt-ip.com Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-05-31mac80211: Add HE 6GHz capabilities element to probe requestIlan Peer1-8/+9
On 6 GHz, the 6 GHz capabilities element should be added, do that. Signed-off-by: Ilan Peer <ilan.peer@intel.com> [add commit message] Link: https://lore.kernel.org/r/20200528213443.8ee764f0cde0.I2b0c66b60e11818c97c9803e04a6a197c6376243@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-05-31mac80211: avoid using ext NSS high BW if not supportedJohannes Berg1-0/+6
If the AP advertises inconsistent data, namely it has CCFS1 or CCFS2, but doesn't advertise support for 160/80+80 bandwidth or "Extended NSS BW Support", then we cannot use any MCSes in the the higher bandwidth. Thus, avoid connecting with higher bandwidth since it's less efficient that way. Link: https://lore.kernel.org/r/20200528213443.0e55d40c3ccc.I6fd0b4708ebd087e5e46466c3e91f6efbcbef668@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-04-24mac80211: add freq_offset to RX statusThomas Pedersen1-1/+2
RX status needs a KHz component, so add freq_offset. We can reduce the bits for the frequency since 60 GHz isn't supported. Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com> Link: https://lore.kernel.org/r/20200402011810.22947-5-thomas@adapt-ip.com [fix commit message] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-04-24mac80211: handle channel frequency offsetThomas Pedersen1-0/+1
cfg80211_chan_def and ieee80211_channel recently gained a frequency offset component. Handle this where it makes sense (potentially required by S1G channels). For IBSS, TDLS, CSA, and ROC we return -EOPNOTSUPP if a channel with frequency offset is passed, since they may or may not work. Once someone tests and verifies these commands work on thos types of channels, we can remove that error. join_ocb and join_mesh look harmless because they use a simple ieee80211_vif_use_channel(), which is using an already verified channel, so we let those through. Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com> Link: https://lore.kernel.org/r/20200402011810.22947-4-thomas@adapt-ip.com Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-02-21cfg80211: remove support for adjacent channel compensationEmmanuel Grumbach1-2/+1
The only driver that used that was iwlwifi and it removed support for this. Remove the feature here as well. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Link: https://lore.kernel.org/r/20200214232336.a530de38e511.I393bc395f6037c8cca6421ed550e3072dc248aed@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2019-10-07mac80211: fix scan when operating on DFS channels in ETSI domainsAaron Komisar1-2/+28
In non-ETSI regulatory domains scan is blocked when operating channel is a DFS channel. For ETSI, however, once DFS channel is marked as available after the CAC, this channel will remain available (for some time) even after leaving this channel. Therefore a scan can be done without any impact on the availability of the DFS channel as no new CAC is required after the scan. Enable scan in mac80211 in these cases. Signed-off-by: Aaron Komisar <aaron.komisar@tandemg.com> Link: https://lore.kernel.org/r/1570024728-17284-1-git-send-email-aaron.komisar@tandemg.com Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2019-06-19treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500Thomas Gleixner1-4/+1
Based on 2 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation # extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 4122 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Enrico Weigelt <info@metux.net> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-08mac80211: support multi-bssidSara Sharon1-2/+9
Add support for multi-bssid. This includes: - Parsing multi-bssid element - Overriding DTIM values - Taking into account in various places the inner BSSID instead of transmitter BSSID - Save aside some multi-bssid properties needed by drivers Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2019-02-08mac80211: move the bss update from elements to an helperSara Sharon1-70/+80
This will allow iterating over multiple BSSs inside cfg80211_bss, in case of multiple BSSID. Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2019-02-08mac80211: pass bssids to elements parsing functionSara Sharon1-35/+40
In multiple BSSID, we have nested IEs inside the multiple BSSID IE, that override the external ones for that specific BSS. As preparation for supporting that, pass 2 BSSIDs to the parse function, the transmitter, and the selected BSSID, so it can know which IEs to choose. If the selected BSSID is NULL, the outer ones will be applied. Change ieee80211_bss_info_update to parse elements itself, instead of receiving them parsed, so we have the relevant bss entry in hand. Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-11-09mac80211: allow hardware scan to fall back to softwareJohannes Berg1-4/+18
In some cases, like in the rsi driver hardware scan offload, there may be scenarios in which hardware scan might not be available or desirable. Allow drivers to cope with this by letting them fall back to software scan by returning the special value 1 from the hardware scan method. Requested-by: Sushant Kumar Mishra <sushant2k1513@gmail.com> Requested-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-06-30Merge tag 'mac80211-next-for-davem-2018-06-29' of ↵David S. Miller1-6/+50
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next Small merge conflict in net/mac80211/scan.c, I preserved the kcalloc() conversion. -DaveM Johannes Berg says: ==================== This round's updates: * finally some of the promised HE code, but it turns out to be small - but everything kept changing, so one part I did in the driver was >30 patches for what was ultimately <200 lines of code ... similar here for this code. * improved scan privacy support - can now specify scan flags for randomizing the sequence number as well as reducing the probe request element content * rfkill cleanups * a timekeeping cleanup from Arnd * various other cleanups ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-15mac80211: support scan features for improved scan privacyJohannes Berg1-5/+30
Support the new random SN and minimal probe request contents scan flags for the case of software scan - for hardware scan the drivers need to opt in, but may need to do only that, depending on their implementation. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
2018-06-15mac80211: split ieee80211_send_probe_req()Johannes Berg1-2/+20
This function is passed many more parameters in the scan case than in the MLME case, and differentiates the two cases inside. Split it up and make both versions static to simplify things. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
2018-06-15mac80211: add probe request building flagsJohannes Berg1-3/+4
Add flags to pass through to probe request building and change the "bool directed" to be one of them. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
2018-06-12treewide: kzalloc() -> kcalloc()Kees Cook1-1/+1
The kzalloc() function has a 2-factor argument form, kcalloc(). This patch replaces cases of: kzalloc(a * b, gfp) with: kcalloc(a * b, gfp) as well as handling cases of: kzalloc(a * b * c, gfp) with: kzalloc(array3_size(a, b, c), gfp) as it's slightly less ugly than: kzalloc_array(array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: kzalloc(4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ type TYPE; expression THING, E; @@ ( kzalloc( - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | kzalloc( - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression COUNT; typedef u8; typedef __u8; @@ ( kzalloc( - sizeof(u8) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(__u8) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(char) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(unsigned char) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(u8) * COUNT + COUNT , ...) | kzalloc( - sizeof(__u8) * COUNT + COUNT , ...) | kzalloc( - sizeof(char) * COUNT + COUNT , ...) | kzalloc( - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - kzalloc + kcalloc ( - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ identifier SIZE, COUNT; @@ - kzalloc + kcalloc ( - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( kzalloc( - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( kzalloc( - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc( - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc( - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ identifier STRIDE, SIZE, COUNT; @@ ( kzalloc( - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression E1, E2, E3; constant C1, C2, C3; @@ ( kzalloc(C1 * C2 * C3, ...) | kzalloc( - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | kzalloc( - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | kzalloc( - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | kzalloc( - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( kzalloc(sizeof(THING) * C2, ...) | kzalloc(sizeof(TYPE) * C2, ...) | kzalloc(C1 * C2 * C3, ...) | kzalloc(C1 * C2, ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - kzalloc + kcalloc ( - (E1) * E2 + E1, E2 , ...) | - kzalloc + kcalloc ( - (E1) * (E2) + E1, E2 , ...) | - kzalloc + kcalloc ( - E1 * E2 + E1, E2 , ...) ) Signed-off-by: Kees Cook <keescook@chromium.org>
2018-03-21mac80211: inform wireless layer when frame RSSI is invalidTosoni1-1/+3
When the low-level driver returns an invalid RSSI indication, set the signal value to 0 as an indication to the upper layer. Also, skip average level computation if signal is invalid. Signed-off-by: Jean Pierre TOSONI <jp.tosoni@acksys.fr> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-09-21mac80211: oce: enable receiving of bcast probe respRoee Zamir1-9/+28
One of OCE's optimizations is acception of broadcast probe responses. Accept broadcast probe responses but don't set NL80211_EXT_FEATURE_ACCEPT_BCAST_PROBE_RESP. Because a device's firmware may filter out the broadcast probe resp - drivers should set this flag. Signed-off-by: Roee Zamir <roee.zamir@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> [johannes: make accepting broadcast conditional on the nl80211 scan flag that was added for that specific purpose] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-28cfg80211: add request id to cfg80211_sched_scan_*() apiArend Van Spriel1-2/+2
Have proper request id filled in the SCHED_SCAN_RESULTS and SCHED_SCAN_STOPPED notifications toward user-space by having the driver provide it through the api. Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by: Franky Lin <franky.lin@broadcom.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-28mac80211: separate encoding/bandwidth from flagsJohannes Berg1-4/+4
We currently use a lot of flags that are mutually incompatible, separate this out into actual encoding and bandwidth enum values. Much of this again done with spatch, with manual post-editing, mostly to add the switch statements and get rid of the conversions. @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_80MHZ +status->bw = RATE_INFO_BW_80 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_40MHZ +status->bw = RATE_INFO_BW_40 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_20MHZ +status->bw = RATE_INFO_BW_20 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_160MHZ +status->bw = RATE_INFO_BW_160 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_5MHZ +status->bw = RATE_INFO_BW_5 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_10MHZ +status->bw = RATE_INFO_BW_10 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_VHT +status->encoding = RX_ENC_VHT @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_HT +status->encoding = RX_ENC_HT @@ expression status; @@ -status.enc_flags |= RX_ENC_FLAG_VHT +status.encoding = RX_ENC_VHT @@ expression status; @@ -status.enc_flags |= RX_ENC_FLAG_HT +status.encoding = RX_ENC_HT @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_HT) +(status->encoding == RX_ENC_HT) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_VHT) +(status->encoding == RX_ENC_VHT) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_5MHZ) +(status->bw == RATE_INFO_BW_5) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_10MHZ) +(status->bw == RATE_INFO_BW_10) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_40MHZ) +(status->bw == RATE_INFO_BW_40) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_80MHZ) +(status->bw == RATE_INFO_BW_80) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_160MHZ) +(status->bw == RATE_INFO_BW_160) Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-28mac80211: clean up rate encoding bits in RX statusJohannes Berg1-4/+4
In preparation for adding support for HE rates, clean up the driver report encoding for rate/bandwidth reporting on RX frames. Much of this patch was done with the following spatch: @@ expression status; @@ -status->flag & (RX_FLAG_HT | RX_FLAG_VHT) +status->enc_flags & (RX_ENC_FLAG_HT | RX_ENC_FLAG_VHT) @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_SHORTPRE +status->enc_flags op RX_ENC_FLAG_SHORTPRE @@ expression status; @@ -status->flag & RX_FLAG_SHORTPRE +status->enc_flags & RX_ENC_FLAG_SHORTPRE @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_HT +status->enc_flags op RX_ENC_FLAG_HT @@ expression status; @@ -status->flag & RX_FLAG_HT +status->enc_flags & RX_ENC_FLAG_HT @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_40MHZ +status->enc_flags op RX_ENC_FLAG_40MHZ @@ expression status; @@ -status->flag & RX_FLAG_40MHZ +status->enc_flags & RX_ENC_FLAG_40MHZ @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_SHORT_GI +status->enc_flags op RX_ENC_FLAG_SHORT_GI @@ expression status; @@ -status->flag & RX_FLAG_SHORT_GI +status->enc_flags & RX_ENC_FLAG_SHORT_GI @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_HT_GF +status->enc_flags op RX_ENC_FLAG_HT_GF @@ expression status; @@ -status->flag & RX_FLAG_HT_GF +status->enc_flags & RX_ENC_FLAG_HT_GF @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_VHT +status->enc_flags op RX_ENC_FLAG_VHT @@ expression status; @@ -status->flag & RX_FLAG_VHT +status->enc_flags & RX_ENC_FLAG_VHT @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_STBC_MASK +status->enc_flags op RX_ENC_FLAG_STBC_MASK @@ expression status; @@ -status->flag & RX_FLAG_STBC_MASK +status->enc_flags & RX_ENC_FLAG_STBC_MASK @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_LDPC +status->enc_flags op RX_ENC_FLAG_LDPC @@ expression status; @@ -status->flag & RX_FLAG_LDPC +status->enc_flags & RX_ENC_FLAG_LDPC @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_10MHZ +status->enc_flags op RX_ENC_FLAG_10MHZ @@ expression status; @@ -status->flag & RX_FLAG_10MHZ +status->enc_flags & RX_ENC_FLAG_10MHZ @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_5MHZ +status->enc_flags op RX_ENC_FLAG_5MHZ @@ expression status; @@ -status->flag & RX_FLAG_5MHZ +status->enc_flags & RX_ENC_FLAG_5MHZ @@ assignment operator op; expression status; @@ -status->vht_flag op RX_VHT_FLAG_80MHZ +status->enc_flags op RX_ENC_FLAG_80MHZ @@ expression status; @@ -status->vht_flag & RX_VHT_FLAG_80MHZ +status->enc_flags & RX_ENC_FLAG_80MHZ @@ assignment operator op; expression status; @@ -status->vht_flag op RX_VHT_FLAG_160MHZ +status->enc_flags op RX_ENC_FLAG_160MHZ @@ expression status; @@ -status->vht_flag & RX_VHT_FLAG_160MHZ +status->enc_flags & RX_ENC_FLAG_160MHZ @@ assignment operator op; expression status; @@ -status->vht_flag op RX_VHT_FLAG_BF +status->enc_flags op RX_ENC_FLAG_BF @@ expression status; @@ -status->vht_flag & RX_VHT_FLAG_BF +status->enc_flags & RX_ENC_FLAG_BF @@ assignment operator op; expression status, STBC; @@ -status->flag op STBC << RX_FLAG_STBC_SHIFT +status->enc_flags op STBC << RX_ENC_FLAG_STBC_SHIFT @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_SHORTPRE +status.enc_flags op RX_ENC_FLAG_SHORTPRE @@ expression status; @@ -status.flag & RX_FLAG_SHORTPRE +status.enc_flags & RX_ENC_FLAG_SHORTPRE @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_HT +status.enc_flags op RX_ENC_FLAG_HT @@ expression status; @@ -status.flag & RX_FLAG_HT +status.enc_flags & RX_ENC_FLAG_HT @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_40MHZ +status.enc_flags op RX_ENC_FLAG_40MHZ @@ expression status; @@ -status.flag & RX_FLAG_40MHZ +status.enc_flags & RX_ENC_FLAG_40MHZ @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_SHORT_GI +status.enc_flags op RX_ENC_FLAG_SHORT_GI @@ expression status; @@ -status.flag & RX_FLAG_SHORT_GI +status.enc_flags & RX_ENC_FLAG_SHORT_GI @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_HT_GF +status.enc_flags op RX_ENC_FLAG_HT_GF @@ expression status; @@ -status.flag & RX_FLAG_HT_GF +status.enc_flags & RX_ENC_FLAG_HT_GF @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_VHT +status.enc_flags op RX_ENC_FLAG_VHT @@ expression status; @@ -status.flag & RX_FLAG_VHT +status.enc_flags & RX_ENC_FLAG_VHT @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_STBC_MASK +status.enc_flags op RX_ENC_FLAG_STBC_MASK @@ expression status; @@ -status.flag & RX_FLAG_STBC_MASK +status.enc_flags & RX_ENC_FLAG_STBC_MASK @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_LDPC +status.enc_flags op RX_ENC_FLAG_LDPC @@ expression status; @@ -status.flag & RX_FLAG_LDPC +status.enc_flags & RX_ENC_FLAG_LDPC @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_10MHZ +status.enc_flags op RX_ENC_FLAG_10MHZ @@ expression status; @@ -status.flag & RX_FLAG_10MHZ +status.enc_flags & RX_ENC_FLAG_10MHZ @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_5MHZ +status.enc_flags op RX_ENC_FLAG_5MHZ @@ expression status; @@ -status.flag & RX_FLAG_5MHZ +status.enc_flags & RX_ENC_FLAG_5MHZ @@ assignment operator op; expression status; @@ -status.vht_flag op RX_VHT_FLAG_80MHZ +status.enc_flags op RX_ENC_FLAG_80MHZ @@ expression status; @@ -status.vht_flag & RX_VHT_FLAG_80MHZ +status.enc_flags & RX_ENC_FLAG_80MHZ @@ assignment operator op; expression status; @@ -status.vht_flag op RX_VHT_FLAG_160MHZ +status.enc_flags op RX_ENC_FLAG_160MHZ @@ expression status; @@ -status.vht_flag & RX_VHT_FLAG_160MHZ +status.enc_flags & RX_ENC_FLAG_160MHZ @@ assignment operator op; expression status; @@ -status.vht_flag op RX_VHT_FLAG_BF +status.enc_flags op RX_ENC_FLAG_BF @@ expression status; @@ -status.vht_flag & RX_VHT_FLAG_BF +status.enc_flags & RX_ENC_FLAG_BF @@ assignment operator op; expression status, STBC; @@ -status.flag op STBC << RX_FLAG_STBC_SHIFT +status.enc_flags op STBC << RX_ENC_FLAG_STBC_SHIFT @@ @@ -RX_FLAG_STBC_SHIFT +RX_ENC_FLAG_STBC_SHIFT Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-12-13mac80211: Remove unused 'len' variableKirtika Ruchandani1-5/+3
Commit 633e27132625 (mac80211: split sched scan IEs) introduced the len variable to keep track of the return value of ieee80211_build_preq_ies() but did not use it. Compiling with W=1 gives the following warning, fix it. net/mac80211/scan.c: In function ‘__ieee80211_request_sched_scan_start’: net/mac80211/scan.c:1123:9: warning: variable ‘len’ set but not used [-Wunused-but-set-variable] This is a harmless warning and is only being fixed to reduce the noise with W=1 in the kernel. Fixes: 633e27132625 ("mac80211: split sched scan IEs") Cc: David Spinadel <david.spinadel@intel.com> Cc: Alexander Bondar <alexander.bondar@intel.com> Cc: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Kirtika Ruchandani <kirtika@chromium.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-09-15mac80211: fix scan completed tracingJohannes Berg1-1/+1
Passing the 'info' pointer where a 'info->aborted' is expected will always lead to tracing to erroneously record that the scan was aborted, fix that by passing the correct info->aborted. The remaining data will be collected in cfg80211, so I haven't duplicated it here. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-07-06mac80211: report failure to start (partial) scan as scan abortJohannes Berg1-2/+3
Rather than reporting the scan as having completed, report it as being aborted. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-07-06mac80211: Add support for beacon report radio measurementAvraham Stern1-8/+34
Add the following to support beacon report radio measurement with the measurement mode field set to passive or active: 1. Propagate the required scan duration to the device 2. Report the scan start time (in terms of TSF) 3. Report each BSS's detection time (also in terms of TSF) TSF times refer to the BSS that the interface that requested the scan is connected to. Signed-off-by: Assaf Krauss <assaf.krauss@intel.com> Signed-off-by: Avraham Stern <avraham.stern@intel.com> [changed ath9k/10k, at76c59x-usb, iwlegacy, wl1251 and wlcore to match the new API] Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-07-06nl80211: support beacon report scanningAvraham Stern1-2/+7
Beacon report radio measurement requires reporting observed BSSs on the channels specified in the beacon request. If the measurement mode is set to passive or active, it requires actually performing a scan (passive or active, accordingly), and reporting the time that the scan was started and the time each beacon/probe was received (both in terms of TSF of the BSS of the requesting AP). If the request mode is table, this information is optional. In addition, the radio measurement request specifies the channel dwell time for the measurement. In order to use scan for beacon report when the mode is active or passive, add a parameter to scan request that specifies the channel dwell time, and add scan start time and beacon received time to scan results information. Supporting beacon report is required for Multi Band Operation (MBO). Signed-off-by: Assaf Krauss <assaf.krauss@intel.com> Signed-off-by: David Spinadel <david.spinadel@intel.com> Signed-off-by: Avraham Stern <avraham.stern@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-04-12cfg80211: remove enum ieee80211_bandJohannes Berg1-6/+6
This enum is already perfectly aliased to enum nl80211_band, and the only reason for it is that we get IEEE80211_NUM_BANDS out of it. There's no really good reason to not declare the number of bands in nl80211 though, so do that and remove the cfg80211 one. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-04-05mac80211: Support a scan request for a specific BSSIDJouni Malinen1-1/+3
If the cfg80211 scan trigger operation specifies a single BSSID, use that value instead of the wildcard BSSID in the Probe Request frames. Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-04-05mac80211: allow drivers to report CLOCK_BOOTTIME for scan resultsJohannes Berg1-1/+3
This was requested by Android, and the appropriate cfg80211 API had been added by Dmitry. Support it in mac80211, allowing drivers to provide the timestamp. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-01-26mac80211: Requeue work after scan complete for all VIF types.Sachin Kulkarni1-1/+11
During a sw scan ieee80211_iface_work ignores work items for all vifs. However after the scan complete work is requeued only for STA, ADHOC and MESH iftypes. This occasionally results in event processing getting delayed/not processed for iftype AP when it coexists with a STA. This can result in data halt and eventually disconnection on the AP interface. Cc: stable@vger.kernel.org Signed-off-by: Sachin Kulkarni <Sachin.Kulkarni@imgtec.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-01-14mac80211: handle sched_scan_stopped vs. hw restart raceEliad Peller1-0/+8
On hw restart, mac80211 might try to reconfigure already stopped sched scan, if ieee80211_sched_scan_stopped_work() wasn't scheduled yet. This in turn will keep the device driver with scheduled scan configured, while both mac80211 and cfg80211 will clear their sched scan state once the work is scheduled. Fix it by ignoring ieee80211_sched_scan_stopped() calls while in hw restart, and flush the work before starting the reconfiguration. Signed-off-by: Eliad Peller <eliadx.peller@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-12-02mac80211: do not actively scan DFS channelsAntonio Quartulli1-4/+5
DFS channels should not be actively scanned as we can't be sure if we are allowed or not. If the current channel is in the DFS band, active scan might be performed after CSA, but we have no guarantee about other channels, therefore it is safer to prevent active scanning at all. Cc: stable@vger.kernel.org Signed-off-by: Antonio Quartulli <antonio@open-mesh.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-11-03mac80211: don't reconfigure sched scan in case of wowlanEliad Peller1-5/+7
Scheduled scan has to be reconfigured only if wowlan wasn't configured, since otherwise it should continue to run (with the 'any' trigger) or be aborted. The current code will end up asking the driver to start a new scheduled scan without stopping the previous one, and leaking some memory (from the previous request.) Fix this by doing the abort/restart under the proper conditions. Signed-off-by: Eliad Peller <eliadx.peller@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-10-14mac80211: remove PM-QoS listenerJohannes Berg1-1/+0
As this API has never really seen any use and most drivers don't ever use the value derived from it, remove it. Change the only driver using it (rt2x00) to simply use the DTIM period instead of the "max sleep" time. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-10-13mac80211: use new cfg80211_inform_bss_frame_data() APIJohannes Berg1-10/+9
The new API is more easily extensible with a metadata struct passed to it, use it in mac80211. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-06-10mac80211: convert HW flags to unsigned long bitmapJohannes Berg1-5/+5
As we're running out of hardware capability flags pretty quickly, convert them to use the regular test_bit() style unsigned long bitmaps. This introduces a number of helper functions/macros to set and to test the bits, along with new debugfs code. The occurrences of an explicit __clear_bit() are intentional, the drivers were never supposed to change their supported bits on the fly. We should investigate changing this to be a per-frame flag. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-06-09mac80211: ignore invalid scan RSSI valuesSara Sharon1-1/+7
Channels in 2.4GHz band overlap, this means that if we send a probe request on channel 1 and then move to channel 2, we will hear the probe response on channel 2. In this case, the RSSI will be lower than if we had heard it on the channel on which it was sent (1 in this case). The scan result ignores those invalid values and the station last signal should not be updated as well. In case the scan determines the signal to be invalid turn on the flag so the station last signal will not be updated with the value and thus user space probing for NL80211_STA_INFO_SIGNAL and NL80211_STA_INFO_SIGNAL_AVG will not get this invalid RSSI value. Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-06-02mac80211: rename single hw-scan flag to follow naming conventionJohannes Berg1-3/+3
The naming convention is to always have the flags prefixed with IEEE80211_HW_ so they're 'namespaced', make this flag follow it. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-03-30mac80211: IBSS fix scan requestJanusz.Dziedzic@tieto.com1-9/+16
In case of wide bandwidth (wider than 20MHz) used by IBSS, scan all channels in chandef to be able to find neighboring IBSS netwqworks that use the same overall channels but a different control channel. Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-01-23mac80211: complete scan work immediately if quiesced or suspendedLuciano Coelho1-0/+5
It is possible that a deferred scan is queued after the queues are flushed in __ieee80211_suspend(). The deferred scan work may be scheduled by ROC or ieee80211_stop_poll(). To make sure don't start a new scan while suspending, check whether we're quiescing or suspended and complete the scan immediately if that's the case. Signed-off-by: Luciano Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-01-14mac80211: don't defer scans in case of radar detectionEliad Peller1-1/+1
Radar detection can last indefinite time. There is no point in deferring a scan request in this case - simply return -EBUSY. Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-01-14mac80211: remove local->radar_detect_enabledEliad Peller1-1/+1
local->radar_detect_enabled should tell whether radar_detect is enabled on any interface belonging to local. However, it's not getting updated correctly in many cases (actually, when testing with hwsim it's never been set, even when the dfs master is beaconing). Instead of handling all the corner cases (e.g. channel switch), simply check whether radar detection is enabled only when needed, instead of caching the result. Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-01-14mac80211: let flush() drop packets when possibleEmmanuel Grumbach1-2/+2
When roaming / suspending, it makes no sense to wait until the transmit queues of the device are empty. In extreme condition they can be starved (VO saturating the air), but even in regular cases, it is pointless to delay the roaming because the low level driver is trying to send packets to an AP which is far away. We'd rather drop these packets and let TCP retransmit if needed. This will allow to speed up the roaming. For suspend, the explanation is even more trivial. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-11-19mac80211: allow drivers to support NL80211_SCAN_FLAG_RANDOM_ADDRJohannes Berg1-10/+38
Allow drivers to support NL80211_SCAN_FLAG_RANDOM_ADDR with software based scanning and generate a random MAC address for them for every scan request with the flag. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-13 17:41:22 +0000